Junlan Electronic OKUSBB66232 SOUNDBAR SPEAKER User Manual 1

Shenzhen Junlan Electronic Ltd SOUNDBAR SPEAKER 1

User Manual

Please read this instruction manual carefully and keep it for future referenceMODEL:T-23237" Bluetooth Soundbar Speaker
WARNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSETHIS UNIT TO RAIN OR MOISTURE.WARNING: USE UNDER SUPERVISION OF AN ADULT DUE TO LONGCORD This unit has a long cord that can be easily tripped on or pulled on,causing injury. Please make sure it is arranged so that it will not drape over atabletop, etc. Where it can be pulled on by children or tripped over accidentally.FCC STATEMENT:This device complies with part 15 of the FCC Rules. Operation is subject to thefollowing two conditions:(1)This device may not cause harmful interference, and(2)This device must accept any interference received, including interferencethat may cause undesired operation. The antenna(s) used for this transmittermust be installed to provide a separation distance of at least 20 cm from allpersons and must not be co-located or operating in conjunction with any otherantenna or transmitter.CAUTION: TO REDUCE THE ELECTRIC SHOCK, DO NOT REMOVE THECOVER (OR BACK). NO USER SERVICEABLE PART INSIDE, REFERSERVICING TO QUALIFIED SERVICE PERSONNEL.CAUTIONRISK OF ELECTRIC SHOCK DO NOT OPENDANGEROUS VOLTAGE:The lighting flash with arrowhead symbol withinan equilateral triangle is intended to alert the user to the presence ofuninsulated “dangerous voltage” within the product’s enclosure that maybe of sufficient magnitude to constitute a risk of electric shock to persons.ATTENTION:The exclamation point within an equilateral triangle is intended toalert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance.2
This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interference by one or more ofthe following measures:●Reorient or relocate the receiving antenna.●Increase the separation between the equipment and receiver.●Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected.●Consult the dealer or an experienced radio/TV technician for help.FCC WARNING:To assure continued operation, follow the attached installation instructions anduse only shield cables when connecting to other devices. Changes ormodifications not expressly approved by the party responsible for compliancecould void the user's authority to operate the equipment.Before using the unit, be sure to read all operating instruction carefully, pleasenote that these are general precautions and may not pertain to your unit. Forexample, this unit may not have the capability to be connected to an outdoorantenna.1. Read these instructionsAll the safety and operating instructions should be read before the appliance isoperated.2. Keep these instructionsThe safety and operating instructions should be kept for future reference.3. Heed all warningsAll warnings on the appliance and in the operating instructions should beadhered to.4. Follow all instructionsAll operation and use instructions should be followed.FCC NOTICE:5. Do not use this apparatus near waterThe appliance should not be used near water; for example, near a bath tub,3
washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimmingpool.6. Clean only with dry clothThe appliance should be cleaned only as recommended by the manufacturer.7. Do not block any ventilation openings.Install in accordance with themanufacturer’s instructions.Slots and openings in the cabinet and in the back or bottom are provided forventilation, to ensure reliable operation of the product and to protect it fromoverheating. These openings must not be blocked or covered. The openingsshould never be blocked by placing the product on a bed, sofa, rug, or similarsurface. This product should never be placed near or over a radiator or heatsource. This product should not be placed in a built-in installation, such as abookcase or rack unless proper ventilation is provided or the manufacturer’sinstructions have been adhered to.8. Do not install near any heat sources such as radiators, heat registers,stoves, or other apparatus (including amplifiers) that produce heat.9. Do not defeat the safety purpose of the polarized or grounding-typeplug. A polarized plug has two blades with one wider than the other. Agrounding type plug has two blades and a third grounding prong. Thewide or the third prong are provided for your safety. If the provided plugdoes not fit into your outlet, consult an electrician for replacement of theobsolete outlet.10. Protect the power cord from being walked on or pinched particularlyat plugs, convenience receptacles, and the point where they exit from theapparatus.11. Only use attachments / accessories specified by the manufacturer.12. Use only with a cart, stand, tripod, bracket, or tablespecified by the manufacturer, or sold with the apparatus.When a cart is used, use caution when moving thecart/apparatus combination to avoid injuryfrom tip-over.An appliance and cart combination should be moved with care. Quick stop,excessive fore and uneven surfaces may cause the appliance and cartcombination to overturn.13. Unplug this apparatus during lightning storms or when unused forlong periods of time.To protect your product from a lightning storm, or when it is left unattended andunused for long periods of time, unplug it from the wall outlet and disconnectthe antenna or cable system. This will prevent damage to the product due tolightning and power-line surges.14. Refer all servicing to qualified service personnel. Servicing isrequired when the apparatus has been damaged in any way, such aspower-supply cord or plug is damaged, liquid has been spilled or objectshave fallen into the apparatus, the apparatus has been exposed to rain or4
moisture, does not operate normally, or has been dropped.15. Power sourceThis product should be operated only from the type of power source indicatedon the marking label. If you are not sure of the type of power supply to yourhome, consult your appliance dealer or local power company. For productsintended to operate from battery power, or other source, refer to the operationinstructions.16. Power linesAn outside antenna system should not be located in the vicinity of overheadpower lines or other electric light or power circuits, or where it can fall into suchpower lines or circuits. When installing an outside antenna system, extremecare should be taken to keep from touching such power lines or circuits ascontact with them might be fatal.17. OverloadingDo not overload wall outlets and extension cords as this can result in a risk offire or electric shock.18. Object and liquid entryNever push objects of any kind into the product through openings as they maytouch dangerous voltage points or short out parts that could result in fire orelectric shock. Never spill or spray any type of liquid on the product.19. Outdoor antenna groundingIf an outside antenna is connected to the product, be sure the antenna systemis grounded so as to provide some protection against voltage surges and builtup static charges. Section 810 of the National Electric Code ANSI/ NFPA 70provides information with respect to proper grounding of the mast andsupporting structure, grounding of the lead- in wire to an antenna dischargeproduct, size of grounding conductors, location of antenna- discharge product,connection to grounding electrodes and requirements for the groundingelectrodes.5
20. ServiceDo not attempt to service this product yourself as opening or removing coversmay expose you to dangerous voltage or other hazards. Refer all servicing toqualified service personnel.b)If liquid has been spilled or objects have fallen into the product.c)If the product has been exposed to rain or water.d)If the product does not operate normally by following the operatinginstructions. Adjust only those controls that are covered by the operatinginstructions, as an adjustment of other controls may result in damage and willrequire extensive work by a qualified technician to restore the product to itsnormal operation.e)If the product has been dropped or the cabinet has been damaged.f)When the product exhibits a distinct change in performance- this indicates aneed for service.25. Note to CATV system installerThis reminder is provided to call the CATV system installer' s attention toArticle 820- 40 of the NEC that provides guidelines for proper grounding and,in particular, specifies that the cable ground shall be connected to thegrounding system of the building, as close to the point of cable entry aspractical.NOTE: Refer all servicing to qualified service personnel. Servicing isrequired when the unit has been damaged in any way such as thefollowing: the power-supply cord or plug has been damaged, liquid hasbeen spilled into unit, the unit has been exposed to rain or moisture, theunit has been dropped or the unit does not operate normally.21. Replacement partsWhen replacement parts are required, be sure the service technician usesreplacement parts specified by the manufacturer or those that have the samecharacteristics as the original parts. Unauthorized substitutions may result infire or electric shock or other hazards.22. Safety checkUpon completion of any service or repairs to this product, ask the servicetechnician to perform safety checks to determine that the product is in properoperating condition.23. Wall or ceiling mountingThe product should be mounted to a wall or ceiling only as recommended bythe manufacturer.24. Damage requiring serviceUnplug this product from the wall outlet and refer service to qualified servicepersonnel under the following conditions.a)When the power- supply cord or plug is damaged.6
INSTALLATION123Main UnitSlave UnitStep 1: Match and insert the Main Unit to Slave Unit.Step 2: Turn the Slave Unit as the arrowhead direction in illustration.Step 3: Make sure both Main Unit and Slave unit fixed firmly.1. Install the Main Unit to Slave UnitWhen placing the Sound Bar on an entertainment center, bookshelf, or any type ofenclosed space, be sure to allow at least 2-3 inches of space around the Sound Bar forventilation. If the Sound Bar is enclosed in a tight space, without ventilation, heatgenerated from the Sound Bar could produce a potential heat hazard.2-3inches2-3inches1.1 Placing on table - ventilation7
A. Mark the position of the mounting screws on the wall using a pencil.C. Put the sound bar onto the mounting screws. Make sure they are firm and stable.35.73 inchesB. Drill the screws directly into the marks that you have made on the wall and leave approx. 0.3 inches length to hook the sound bar.(screws not included)2.1 Mounting to a wooden wall2.2 Mountingto a brick wallA. Mark the position of the mounting screws on the wall using a pencil.E. Put the sound bar onto the mounting screws. Make sure they are firm and stable.C. Insert the fixing plug and hammer into the holes.D. Secure the screws into the fixing plug and leave approx. 0.3 inches length to hookthe sound bar.B. Drill 2 holes on wall with a powerful electric drill. 35.73 inches(screws and plastic fixing plug are not included)907.6mm(35.73 inch)2. The Installation Distance429.6mm(16.9 inch)8
3. Installation to the base●Install the Main Unit to the base132Base for Main UnitBaseMain UnitStep 1: Match and insert the Main Unit to the Base.Step 2: Turn the Main Unit as the arrowhead direction in illustration.Step 3: Make sure Main Unit and Base are fixed firmly.9
●Install the Slave Unit to the base123Base for Slave UnitBaseSlave UnitStep 1: Match and insert the Slave Unit to the Base.Step 2: Turn the Slave Unit as the arrowhead direction in illustration.Step 3: Make sure Slave Unit and Base are fixed firmly.10
PROdUCT OvERvIEW12. USB PLAYER Port112345678910 111. Speaker2. Remote Sensor3. VOL+ Button4. VOL- Button7. Power/Standby Button8. DC IN Jack9. LINE IN Jacks10. AUX IN Jack11. OPTICAL IN JackFront ViewRear View11115. Mode Indicator13SOURCEVO L –VO L +6. Play/Pause ButtonHDMIOPTICA LAUX INUSB PLAYERDC 16V1213. HDMI IN Jack
REMOTE CONTROL121234567101112158913141. POWER Button2. BT Mode Button3. USB Mode Button4. AUX IN Mode Button5. LINE IN Mode Button6. Play/Pause Button7. EQ Button8. Previous Button9. VOL- Button10. MUTE Button11. OPTICAL Mode Button12. HDMI Mode Button13. PAIR Button14. Next Button15. VOL+ Button
BATTERY INSTALLATION OF REMOTE CONTROL913Remote control operation range●When there is an obstacle between the remote and the transmitter, the unit may not operate.●When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong lightshines on the REMOTE SENSOR of the unit, the operation of the remote may be unstable.Battery installation:1.Slide and lift the battery door. polarity markings.3.Close up the battery door.Follow these precautions when using a battery in this device:2.Use only the size and type of battery specified.3.Be sure to follow the correct polarity when installing the battery as indicated in the battery compartment. A reversed battery may cause damage to the device.4.Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with new ones.5.If the batteries in the device are completely drained or the device will not be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.6.Do not try to recharge batteries not included to be recharged; they can overheat and rupture. (Follow battery manufacture’s instructions.)7.The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.9.Clean the battery contacts, and also those the device, prior to battery installation.Battery precaution:8.Remove batteries promptly if consumed.1.Warning-Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.2.Install two “AAA” size batteries into the battery compartment as indicated by the
GENERAL OPERATIONBlue.............................................................................................Bluetooth Mode 1. Connect the AC/DC adapter to the unit and wall outlet. The source indicator will Violet ............................................................................................AUX IN Mode Green.................................................................................................USB Mode Indigo(blue+green).................................................................OPTICAL IN Mode 144. During Playback:~ Press the VOL+ or VOL- buttons repeatedly to adjust volume.~ Press the MUTE button on remote control to turn on or turn off sound.~ Press the EQ button on remote control repeatedly to set to different EQ mode.5. When finish listening, press and hold the /STANDBY button on the unit orstandby mode.2. Press and hold the /STANDBY button on the unit or press the button onremote control to power on the unit.turn red.turn to:Orange(red+green).......................................................................HDMI IN Mode press the button on remote control to put it into3. Press the /STANDBY button on the unit repeatedly or press the BT, USB, OPTICAL, AUX IN, LINE IN or HDMI button on remote control to switch to thedesired mode. The color of source indicator will White(red+green+blue).................................................................LINE IN Mode
BLUETOOTH OPERATION105. After successful paired, the source indicator will stay solid.function is activated and they are in working range.6. During playback:~ Press the or button on remote control to skip tracks.1. Power on the unit as previously explained.remote control, the source indicator will turn Blue and blink. 3. Power on the external Bluetooth enable device and enter Bluetooth mode and try searching the unit.4. When " TEWELL T-232 " appears, select it and make connection.NOTE: The unit will be automatically paired with the last paired Bluetooth device if their Bluetooth 152. Press the /STANDBY button on the unit repeatedly or press the BT button on 7. Press the PAIR button on remote control to disconnect the current connection.~ Press the button on the unit or remote control to pause, press it again to resume playback.
OPTICAL-IN OPERATION4. Power on the connected external player and start playback the music as usual.Turn on the digital audio output and set it to PCM (Plus Code Modulation) type similar to the follows figure:BassTrebleBalanceSelect Move MENU ExitSound Mode StandardSurround OffAVL OffAudio Language EnglishPicture Time Setup Lock OffAudioAudioDigital Output PCMDigital Output PCM1. Connect the Optical out jack from the external audio player (such as TV, DVD player etc.) to the OPTICAL IN jack on the rear of the unit with the optical connection cable as illustated below:(For PCM format only)OPTICAL OUTRear ViewTV or DVD player etc.2. Power on the unit as previously explained.16HDMIOPTICA LAUX INUSB PLAYERDC 16V3. Press the /STANDBY button on the unit repeatedly or press the OPTICAL button on the remote control, the source indicator turns to Indigo(blue+green).
LINE IN OPERATION An external Audio/Video player(such as TV, DVD palyer etc.) can be connected to this unit and listen through the unit's speakers.1. Plug one end of the line in cable into the LINE IN jacks(L&R) on the unit.2. Plug the other end of the line in cable into the Line Out jacks(L&R) on TV or DVDpalyer etc.Line out jacks of TV/DVD player etc.LR Video5. Power on the connected external player and start playback the music as usual.3. Power on the unit as previously explained.17whiteredRear ViewHDMIOPTICA LAUX INUSB PLAYERDC 16V4. Press the /STANDBY button on the unit repeatedly or press the LINE IN button on the remote control, the source indicator turns to White(red+green+blue).
AUX IN OPERATIONAn external Audio player(such as mobile phone, MP3 palyer etc.) can be connected to this unit and listen through the unit's speakers.Mobile PhoneConnect to the Phones; AUX Out;Line Out Jack of the external devices (Such like MP3 Player; cell phones; iPod/iPad ... etc)MP3 Player1. Plug one end of the AUX IN Cable into the AUX IN jack on the unit.2. Plug another end of the AUX IN Cable into the headphone hack or Aux Out jackon the external audio player.5. Power on the connected external player and start playback the music as usual.3. Power on the unit as previously explained.18Rear ViewHDMIOPTICA LAUX INUSB PLAYERDC 16V4. Press the /STANDBY button on the unit repeatedly or press the AUX IN button on the remote control, the source indicator turns to Violet.
19HdMI IN OPERATION An external Audio/Video player(such as TV, DVD palyer etc.) can be connected to this unit and listen through the unit's speakers.1. Plug one end of the HDMI cable into the HDMI IN port on the unit.2. Plug the other end of the HDMI cable into the HDMI IN (ARC) port on TV or DVDpalyer etc.HDMI out jacks of TV/DVD player etc.LR Video5. Power on the connected external player and start playback the music as usual.3. Power on the unit as previously explained.Rear ViewHDMI IN (ARC)Explanation: ARC (Audio Return Channel)HDMIOPTICA LAUX INUSB PLAYERDC 16V4. Press the /STANDBY button on the unit repeatedly or press the HDMI button on the remote control, the source indicator turns to Orange(red+green).
20USB PLAYER OPERATION1. Power on the unit as previously explained.2. Press the /STANDBY button on the unit repeatedly or press the USB buttonon the remote control, the source indicator turns to Green. 3. Insert an USB Device to the USB PLAYER port on the unit. The unit willautomatically play after a few seconds.4. During playback:~ Press the or button on remote control to skip tracks.~ Press the button on the unit or remote control to pause, press it again to resume playback.HDMIOPTICA LAUX INUSB PLAYERDC 16VUSB
TROUBLESHOOTINGPlay music/movie in the paired/connected device as usual and makesure the volume level of it is in highlevel.Sound distortion/rattle Volume level too high Reduce the volume level by pressingReduce the volume level of thepaired/connected device.Bluetoothreception failurePut the external BT device close to theunit.Have not paired Pair the unit with the BT Device as theprocedures stated in this manual.Input source incorrectThe unit is in standby modeThe paired/connected deviceis not in playback modeThe external device istoo far from the unitRemote Controlnot functioning Out of rangeThe batteries in the remotecontrol are drainedPoint the remote control to theremote sensor on the unit within16 feet, +/-30 degressReplace with new batteryNo sound orsound weakVolume level in minimum position Raise the volume level by pressing the VOL + Button on the unitSYMPTOM POSSIBLE CAUSE POSSIBLE SOLUTIONNo power The adapter is not connected Connect the adapter to the unit and wall outletto power on the unitOr press VOL+ button on remote controlon remote control to switch to desiredmode the VOL - Button on the unitOr press VOL- button on remote control21Press the SOURCE button on unit orPress and hold the /STANDBY button on unit or or press the button on remote control
SPECIFICATIONSSPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGEWITHOUT NOTICEis a trademark on a registered trademark of BluetoothSIG Inc. All other trademarks and trade names are those of their respective owners.22Power input ............................................................................AC100~240V, 50/60HzPower output ......................................................................DC16V 1.8AAudio output ...................................................................................................4x7.5WBluetooth effective working range in open area......................................up to 32 feetRemote effective working range..............................................................up to 16 feetPACKAGES1 x User Manual1 x Power Adapter1 x Remote Control 1 x AUX IN Cable 1 x LINE IN Cable1 x Main Unit & Slave Unit2 x Metal Bases

Navigation menu