Junlan Electronic ONB18SB ONN 37in BLUETOOTH SOUNDBAR User Manual 1

Shenzhen Junlan Electronic Ltd ONN 37in BLUETOOTH SOUNDBAR 1

User Manual

PRODUCT GUIDEONN 37" BLUETOOTH SOUNDBARMODEL:ONB18SB001
WARNING:TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSETHIS UNIT TO RAIN OR MOISTURE.WARNING: USE UNDER SUPERVISION OF AN ADULT DUE TO LONGCORD This unit has a long cord that can be easily tripped on or pulled on,causing injury. Please make sure it is arranged so that it will not drape over atabletop, etc. Where it can be pulled on by children or tripped over accidentally.FCC STATEMENT:This device complies with part 15 of the FCC Rules. Operation is subject to thefollowing two conditions:(1)This device may not cause harmful interference, and(2)This device must accept any interference received, including interferencethat may cause undesired operation. The antenna(s) used for this transmittermust be installed to provide a separation distance of at least 20 cm from allpersons and must not be co-located or operating in conjunction with any otherantenna or transmitter.CAUTION: TO REDUCE THE ELECTRIC SHOCK, DO NOT REMOVE THECOVER (OR BACK). NO USER SERVICEABLE PART INSIDE, REFERSERVICING TO QUALIFIED SERVICE PERSONNEL.CAUTIONRISK OF ELECTRIC SHOCK            DO NOT OPENDANGEROUS VOLTAGE:The lighting flash with arrowhead symbol withinan equilateral triangle is intended to alert the user to the presence ofuninsulated “dangerous voltage” within the product’s enclosure that maybe of sufficient magnitude to constitute a risk of electric shock to persons.ATTENTION:The exclamation point within an equilateral triangle is intended toalert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance.2This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1)this device may not cause interference(2) this device must accept any interference, including interference that may cause undesired operation of the device.      (1) l'appareil ne doit pas produire de brouillage, etLe présent appareil est conforme aux CNR d'Industrie Canada applicables auxappareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si  le brouillage est susceptible d'en compromettre lefonctionnement.
This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off andon, the user is encouraged to try to correct the interference by one or more ofthe following measures:●Reorient or relocate the receiving antenna.●Increase the separation between the equipment and receiver.●Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected.●Consult the dealer or an experienced radio/TV technician for help.FCC WARNING:To assure continued operation, follow the attached installation instructions anduse only shield cables when connecting to other devices. Changes ormodifications not expressly approved by the party responsible for compliancecould void the user's authority to operate the equipment.Before using the unit, be sure to read all operating instruction carefully, pleasenote that these are general precautions and may not pertain to your unit. Forexample, this unit may not have the capability to be connected to an outdoorantenna.1. Read these instructionsAll the safety and operating instructions should be read before the appliance isoperated.2. Keep these instructionsThe safety and operating instructions should be kept for future reference.3. Heed all warningsAll warnings on the appliance and in the operating instructions should beadhered to.4. Follow all instructionsAll operation and use instructions should be followed.FCC NOTICE:5. Do not use this apparatus near waterThe appliance should not be used near water; for example, near a bath tub,3
washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimmingpool.6. Clean only with dry clothThe appliance should be cleaned only as recommended by the manufacturer.7. Do not block any ventilation openings.Install in accordance with themanufacturer’s instructions.Slots and openings in the cabinet and in the back or bottom are provided forventilation, to ensure reliable operation of the product and to protect it fromoverheating. These openings must not be blocked or covered. The openingsshould never be blocked by placing the product on a bed, sofa, rug, or similarsurface. This product should never be placed near or over a radiator or heatsource. This product should not be placed in a built-in installation, such as abookcase or rack unless proper ventilation is provided or the manufacturer’sinstructions have been adhered to.8. Do not install near any heat sources such as radiators, heat registers,stoves, or other apparatus (including amplifiers) that produce heat.9. Do not defeat the safety purpose of the polarized or grounding-typeplug. A polarized plug has two blades with one wider than the other. Agrounding type plug has two blades and a third grounding prong. Thewide or the third prong are provided for your safety. If the provided plugdoes not fit into your outlet, consult an electrician for replacement of theobsolete outlet.10. Protect the power cord from being walked on or pinched particularlyat plugs, convenience receptacles, and the point where they exit from theapparatus.11. Only use attachments / accessories specified by the manufacturer.12. Use only with a cart, stand, tripod, bracket, or tablespecified by the manufacturer, or sold with the apparatus.When a cart is used, use caution when moving thecart/apparatus combination to avoid injuryfrom tip-over.An appliance and cart combination should be moved with care. Quick stop,excessive fore and uneven surfaces may cause the appliance and cartcombination to overturn.13. Unplug this apparatus during lightning storms or when unused forlong periods of time.To protect your product from a lightning storm, or when it is left unattended andunused for long periods of time, unplug it from the wall outlet and disconnectthe antenna or cable system. This will prevent damage to the product due tolightning and power-line surges.14. Refer all servicing to qualified service personnel. Servicing isrequired when the apparatus has been damaged in any way, such aspower-supply cord or plug is damaged, liquid has been spilled or objectshave fallen into the apparatus, the apparatus has been exposed to rain or4
moisture, does not operate normally, or has been dropped.15. Power sourceThis product should be operated only from the type of power source indicatedon the marking label. If you are not sure of the type of power supply to yourhome, consult your appliance dealer or local power company. For productsintended to operate from battery power, or other source, refer to the operationinstructions.16. Power linesAn outside antenna system should not be located in the vicinity of overheadpower lines or other electric light or power circuits, or where it can fall into suchpower lines or circuits. When installing an outside antenna system, extremecare should be taken to keep from touching such power lines or circuits ascontact with them might be fatal.17. OverloadingDo not overload wall outlets and extension cords as this can result in a risk offire or electric shock.18. Object and liquid entryNever push objects of any kind into the product through openings as they maytouch dangerous voltage points or short out parts that could result in fire orelectric shock. Never spill or spray any type of liquid on the product.19. Outdoor antenna groundingIf an outside antenna is connected to the product, be sure the antenna systemis grounded so as to provide some protection against voltage surges and builtup static charges. Section 810 of the National Electric Code ANSI/ NFPA 70provides information with respect to proper grounding of the mast andsupporting structure, grounding of the lead- in wire to an antenna dischargeproduct, size of grounding conductors, location of antenna- discharge product,connection to grounding electrodes and requirements for the groundingelectrodes.5
20. ServiceDo not attempt to service this product yourself as opening or removing coversmay expose you to dangerous voltage or other hazards. Refer all servicing toqualified service personnel.b)If liquid has been spilled or objects have fallen into the product.c)If the product has been exposed to rain or water.d)If the product does not operate normally by following the operatinginstructions. Adjust only those controls that are covered by the operatinginstructions, as an adjustment of other controls may result in damage and willrequire extensive work by a qualified technician to restore the product to itsnormal operation.e)If the product has been dropped or the cabinet has been damaged.f)When the product exhibits a distinct change in performance- this indicates aneed for service.25. Note to CATV system installerThis reminder is provided to call the CATV system installer' s attention toArticle 820- 40 of the NEC that provides guidelines for proper grounding and,in particular, specifies that the cable ground shall be connected to thegrounding system of the building, as close to the point of cable entry aspractical.NOTE: Refer all servicing to qualified service personnel. Servicing isrequired when the unit has been damaged in any way such as thefollowing: the power-supply cord or plug has been damaged, liquid hasbeen spilled into unit, the unit has been exposed to rain or moisture, theunit has been dropped or the unit does not operate normally.21. Replacement partsWhen replacement parts are required, be sure the service technician usesreplacement parts specified by the manufacturer or those that have the samecharacteristics as the original parts. Unauthorized substitutions may result infire or electric shock or other hazards.22. Safety checkUpon completion of any service or repairs to this product, ask the servicetechnician to perform safety checks to determine that the product is in properoperating condition.23. Wall or ceiling mountingThe product should be mounted to a wall or ceiling only as recommended bythe manufacturer.24. Damage requiring serviceUnplug this product from the wall outlet and refer service to qualified servicepersonnel under the following conditions.a)When the power- supply cord or plug is damaged.6
AUX INLINE INL ROPT INDC IN      16VPROdUCT OvERvIEW7TOP PANELFRONT VIEWREAR PANEL910 112. Remote Sensor5. Mode Indicator6. Volume Down Button7. Volume Up Button3. Power On/Off Button4. Mode Switch Button 9. OPTICAL IN Jack10. LINE IN Jacks8. AUX IN Jack11. DC IN Jack/I AUXINOPTINLINEIN1124 5 67831. Speaker
BATTERY INSTALLATION OF REMOTE CONTROLFig.1Fig.2 Fig.3Remove and discard the insulation film as Fig.1.Replacing battery for Remote ControlFirst time use8REMOTE CONTROL12345678910111.    (Power On/Off) Button2. AUX Button3. LINE IN Button4.      (Previous) Button6.      (Mute) Button10.      (Next) Button11.      Play/Pause Button12.          (Volume Up/Down)Button9.       (Mode Switch) ButtonOPENOPEN3V CR20253V CR20251. Pull out the battery holder as Fig.2.2. Replace the old button cell with a new CR2025 button cell  with the polarity markings facing upward as Fig.3.3. Push back the battery holder as Fig.4.Fig.4AUX OPTICALLINEIN      TALK MOVIEMUSICSound ModeVOLSTANDARD127.      (Bluetooth)Button8. OPTICAL Button5. Sound Mode (MUSIC, TALK, MOVIE, STANDARD)
99BATTERY PRECAUTIONSFollow these precautions when using a battery in this device:1. Use only the size and type of battery specified.2. Be sure to follow the correct polarity when installing the battery as indicated in the batterycompartment, a reserved battery may cause damage to the device.3. Do not mix different types of batteries together ( e.g: Alkaline and Carbon -zinc )or old batteries with fresh ones.4. If the batteries in the device are consumed or the device is not to be used for a long period of time,remove the batteries to prevent damage or injury from possible leakage.5. Do not try to recharge the battery as it is not intended to be recharged; it can overheat and rupture.(Follow the battery manufacturer’s instructions.)6. The batteries shall not be exposed to excessive heat such as sunshine or fire.7. Clean the battery contacts and also those of the device prior to battery installation.8. The remote control is supplied with a coin/buttoncell battery. If the coin button cell battery isswallowed, it can cause severe internal burns injust 2 hours and can lead to death. Keep newand used battery away from children. If theBattery compartment does not close securely,stop using the product and keep it away fromchildren. If you think batteries might have beenswallowed or placed any part of the body, seekimmediate medical attention.CR2025Remote control operation range●●When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong lightshines on the REMOTE SENSOR of the unit, the operation of the remote may be unstable.CAUTION●Danger of explosion if the battery is incorrectly replaced.●Replace only with the same or equivalent type.16.4 Feet (5M)When there is an obstacle between the transmitter and the unit, the unit may not operate.AUX OPT ICA LLIN EIN      TALK MOVIEMUSICSound ModeVOLSTANDARD
PLACEMENT AND MOUNTING1. Placing the device on a table - VentilationWhen placing the Sound Bar on an entertainment center, bookshelf, or any type ofenclosed space, be sure to allow at least 2-3 inches of space around the Sound Bar forventilation. If the Sound Bar is enclosed in a tight space, without ventilation, heatgenerated from the Sound Bar could produce a potential heat hazard.2. The Installation Distance2-3inches2-3inches10700mm (27.56 inches)
2.1 Mountingto a wooden wallA. Mark the position of the mounting screws on the wall using a pencil.C. Put the sound bar onto the mounting screws. Make sure they are firm and stable.2.2 Mountingto a brick wall27.56 inchesB. Drill the screws directly into the marks that you have made on the wall and leave approx. 0.3 inches length to hook the sound bar.(screws not included)(screws and plastic fixing plug are not included)A. Mark the position of the mounting screws on the wall using a pencil.E. Put the sound bar onto the mounting screws. Make sure they are firm and stable.C. Insert the fixing plug and hammer into the holes.D. Secure the screws into the fixing plug and leave approx. 0.3 inches length to hookthe sound bar.B. Drill 2 holes on wall with a powerful electric drill. 27.56 inches11
GENERAL OPERATION1. Connect the AC/DC adapter to the unit and wall outlet. 3. Press the         button on the unit or remote control repeatedly to switch to the 124. During Playing:~ Press the + or - button on the unit or remote control repeatedly to adjust volume.~ Press the       button on remote control to turn off sound, the  mode indicator on 2. Press  the        button on the unit or press the     button on remote control to power on the unit.5. Press  the        button on the unit or press the     button on remote control toto power off the unit. /Idesired mode. Or press the AUX, OPTICAL,      , LINE IN  button on the remotecontrol to turn to desired mode, the corresponding mode indicator on top of the unit will light up.~ Press the MUSIC button on remote control to turn to MUSIC sound effect mode.~ Press the TALK button on remote control to turn to TALK sound effect mode.~ Press the MOVIE button on remote control to turn to MOVIE sound effect mode.~ Press the STANDARD button on remote control to turn to normal sound effect mode./Ithe unit w ill blink, press the button again to resume.
BLUETOOTH OPERATION105. After successful pairing, the Bluetooth indicator will stop blinking.function are activated and they are in working range.6. During playing:~ Press the       or       button on remote control to skip tracks.~ Press the      button on remote control to pause, press it again to resume.1. Power on the unit as previously explained.3. Power on the external Bluetooth enable device and enter Bluetooth mode and try searching the unit.NOTE: The unit will be automatically connected with the last connected Bluetooth  device if their Bluetooth 137. Press and hold the     button on remote control to disconnect current connection.4. When   appears, select it and make connection.2. Press the       button on the unit or remote control repeatedly or press the    button on remote control to switch to  Bluetooth mode, the Bluetooth indicator on the unit  will turn Blue and blink."ONB18SB001"
AUX IN OPERATIONAn external Audio player(such as mobile phone, MP3 player etc.) can be connected  to this unit and listen through the unit's speakers.Rear PanelMobile PhoneConnect to the Phones; AUX Out;Line Out Jack of the external devices (Such like MP3 Player; cell phones;  iPod/iPad ... etc)MP3 Player1. Plug one end of the AUX IN Cable into the AUX IN  jack on the unit.2. Plug another end of the AUX IN Cable into the headphone jack or Aux Out jackon the external audio player.5. Power on the connected external player and start playing the music as usual.143. Power on the unit as previously explained.4. Press the       button on the unit or remote control repeatedly or press the AUX button on remote control to switch to  AUX IN mode, the AUX IN indicator on the   unit will turn Blue.AUX INLINE INL ROPT INDC IN      16V
LINE IN OPERATION    An external Audio/Video player(such as TV, DVD player etc.) can be connected to this unit and listen through the unit's speakers.1. Plug one end of the line in cable into the LINE IN jacks(L&R) on the unit.2. Plug the other end of the line in cable into the Line Out jacks(L&R) on TV or DVDplayer etc.Line out jacks of TV/DVD player etc.L R Video15white5. Power on the connected external player and start playing the music as usual.3. Power on the unit as previously explained.Rear PanelAUX INLINE INL ROPT INDC IN      16V4. Press the       button on the unit or remote control repeatedly or press the  LINE IN button on remote control to switch to  LINE IN mode, the LINE IN indicator   on the unit will turn Blue.red
OPTICAL-IN OPERATION4. Power on the connected external player and start playing the music as usual.Turn on the digital audio output and set it to PCM (Pulse Code Modulation) type similar to the below figure:BassTrebleBalanceSelect Move MENU ExitSound Mode StandardSurround OffAVL OffAudio Language EnglishPicture Time Setup Lock OffAudioAudioDigital Output PCMDigital Output PCM1. Connect the Optical out jack from the external audio player (such as TV, DVD player etc.) to the OPT IN jack on the rear of the unit with the optical connection cable as illustated below:(For PCM format only)OPTICAL OUTOptical Connection Cable TV or DVD player etc.162. Power on the unit as previously explained.Rear PanelAUX INLINE INL ROPT INDC IN      16V3. Press the       button on the unit or remote control repeatedly or press the  OPTICAL button on remote control to switch to  OPTICAL IN mode, the OPT IN indicator on the unit will turn Blue.(not included)
TROUBLESHOOTINGPlay music/movie in the paired/connected device as usual and makesure the volume level of it is in highlevel.Sound distortion/rattle Volume level too high Reduce the volume level by pressingReduce the volume level of thepaired/connected device.Bluetoothreception failurePut the external BT device close to theunit.Have not paired Pair the unit with the BT Device as theprocedures stated in this manual.Input source incorrectPress the        buttonThe unit is in power off modeThe paired/connected deviceis not in playback modeThe external device istoo far from the unitRemote Controlnot functioning Out of working rangeThe battery in the remotecontrol is drainedPoint the remote control to theremote sensor on the unit within16 feet, +/-30 degressReplace with new batteryNo sound orsound weakVolume level in minimum position  Raise the volume level by pressing the  + Button on the unit or onSYMPTOM POSSIBLE CAUSE POSSIBLE SOLUTIONNo power The adapter is not connected Connect the adapter to the unit and wall outletremote controldesired mode the  - Button on the top of the unitor on remote control17Press the           button on the unit or on remote control to switch to/I on the unit or press the      button on remote control to power on the unit
SPECIFICATIONSSPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGEWITHOUT NOTICE18Power input ............................................................................AC100~240V, 50/60HzPower output ......................................................................DC16V       1.5AAudio output ................................................................................................2x12.5W Bluetooth effective working range in open area......................................up to 32 feetRemote effective working range..............................................................up to 16 feetPACKAGES1x User Manual1x Power Adapter1x Remote Control 1x AUX IN Cable 1x LINE IN Cable1x Main Unit
LIMITED PRODUCT WARRANTYThis quality product is warranted to be free from manufacturer’s defects in material and workman-ship,provided that the unit is used under the normal operating conditions intended by the manufacturer.Should you have any problem with this product, please and it is highly recommended to visit our website atwww.curtisint.com before you take any other steps as we have additional copies of instruction manuals,operating manuals and trouble shooting tips on our website which gives you the answer on most of thequestions you could have in operating the unit.TERMS OF WARRANTYC.I. Service Dept. warrants this product to be free from defects in materials and workmanship for 90 days onparts and 90 days on labor. If you originally purchased your product more than 90 days ago, a repair feemay apply.Nothing within this warranty shall imply that C.I. will be responsible or liable for any damage to any itemsplaced in this product, whether due to any defect of the product, or its use, whether proper or improper.EXCLUSIONSSave as herein provided, C.I. Service Dept. (Canada) or C.I. Service Dept. (USA), there are no otherwarranties, conditions, representations or guarantees, express or implied, made or intended by C.I. or itsauthorized distributors and all other warranties, conditions, representations or guarantees, including anywarranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation orstatue is hereby expressly excluded. Save as herein provided, C.I. Service Dept. (Canada) or C.I. ServiceDept. (USA), shall not be responsible for any damages to persons or property, including the unit itself,howsoever caused or any consequential damages arising from the malfunction of the unit and by thepurchase of the unit, the purchaser does hereby agree to indemnify and save harmless C.I. from any claimfor damages to persons or property caused by the unit.TO OBTAIN REPAIRS UNDER THE TERMS OF THIS WARRANTY1. The original purchaser must present a copy of the original bill of sale and the service warranty card.2. Any alterations, abuse, misuse, battery corrosion or accidental damage voids the warranty.3. The warranty does not cover cabinets and accessories.4. No warranty or insurance contained or set out shall apply when damage or repair is caused by powerfailure; damage in transit or when moving the unit; improper power supply; use for commercial orindustrial purposes; service calls resulting in customer education, etc.5. The defective product should be mailed to:Canada U.S.AC.I. Service Dept. Curtis International Ltd315 Attwell DriveToronto, ONM9W 5C1c/o Lotus International Company6880CommerceBlvd.Canton MI 48187U.S.A.For service assistance and product information, please call: 1-800-968-9853.If mailing the product, the freight must be prepaid and a money order for $7.00 should be includedto cover the cost of insurance and the return of the product.6. C.I. reserves the right to repair or replace the parts which have become defective.Model No. Date Purchased Serial No.

Navigation menu