Junlan Electronic SBB32170 MEDIA CENTER User Manual
Shenzhen Junlan Electronic Ltd MEDIA CENTER
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2732869 |
| Application ID | Lp+XwH2vblEJMfLGtK5ofQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 70.84kB (885533 bits) |
| Date Submitted | 2015-08-31 00:00:00 |
| Date Available | 2015-08-31 00:00:00 |
| Creation Date | 2015-08-28 19:19:05 |
| Producing Software | Acrobat Distiller 11.0 (Windows) |
| Document Lastmod | 2015-08-28 19:19:05 |
| Document Title | untitled |
| Document Author: | Test |
Media Center MODEL:WMSMCZ3 --INSTALLATION AND OPERATION MANUAL-PLEASE READ INSTRUCTIONS CAREFULLY AND KEEP FOR FUTURE REFERENCE The lighting flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER S E RV I C I N G TO Q U A L I F I E D S E RV I C E PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. USE UNDER SUPERVISION OF AN ADULT DUE TO LONG CORD This unit has a long cord that can easily be tripped on or pulled on, causing injury, Please make sure it is arranged so it will not drape over a tabletop, etc. Where it can be pulled on by children or tripped over accidentally. FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not Installed and used in accordance with the instructions, may cause harmful interference to radio is no communications. However, there guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television which can be determined by reception, turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ● Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet with a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. "This equipment complies with FCC RF radiation exposure WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. Before using the unit, be sure to read all operating instructions carefully. Please note that these are general precautions and may not pertain to your unit. 1 ) Read these instructions All the safety and operating instructions should be read before the product is operated. 2 ) Keep these instructions The safety and operating instructions should be retained for future reference. 3 ) Heed all warnings All warnings on the product and in the operating instructions should be adhered to. 4 ) Follow all instructions All operating and use instructions should be followed. limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body." FCC WARNING: To assure continued compliance, follow the attached installation instructions and use only shielded cables when connecting to other devices. Modifications not authorized by the manufacturer may void user`s authority to operate this device. 5 ) Do not use this apparatus near water Do not use this product near water and moisture, for example: near a bathtub, washbowl, kitchen sink or laundry tub; in a wet basement; or near a swimming pool. 13 ) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture does not operate normally, or has been dropped. 6 ) Clean only with dry cloth Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning. 7)Do not block any ventilation openings. Install in accordance with the manufacturer's instructions Slots and openings in the cabinet and in the back or bottom are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should never be placed near or over a radiator or heat source. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 14 ) Power source This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other source, refer to the operation instructions. 15 ) Service Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 8 ) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus(including amplifiers) that produce heat. 9 ) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that objects filled with liquids, such as vases shall not be placed on apparatus. 10 ) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 ) Only use attachments/accessories specified by the manufacturer. 12 ) Unplug this apparatus during lightning storms or when unused for long periods of time To protect your product from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. FEATURES Digital FM tuner w/10 presets Bluetooth wireless technology 4 zone audio distribution 4 zone video distribution 3.5 mm aux input jack on front panel USB input on front panel w/device charging capabilities Digital Optical input on rear panel 2 analog stereo inputs on rear panel LED backlit controls Wireless remote control included PACKING LIST OPTICAL ZONE A ........ ........ ........ ........ ........ ........ ........ ........ BT USB AUX IN FM TV DVD ZONE C റͬറTUN+ റͬറTUN- VOL+ VOL- റͬറ ZONE B PAIR MUTE AAA AAA Main Unit User Manual DC Power Extension (Red and Black) Wire FM Antenna AV Connection Cable Screw Cover Remote Control with Two Batteries External Remote Sensor Screws for Installation Wire Harness for Speakers PLACING AND MOUNTING 1. Placing When plaing the media center in any type of enclosed space, be sure to allowe space around it for ventilation. If plaing in a tight space without ventilation, heat generated from the unit could produce a potential heat hazard. 2. Mounting Mounting Distance 254mm 80mm GENERAL VIEW Front View 11 9 8 10 6. USB Jack 7. AUX IN Jack 8. Play/Pause/ Preset/ Memory/Preset Play Button 9. PAIR Button 10. SOURCE Button 11. POWER Button 1. LED Display 2. Remote Sensor 3. Previous/Tune Down Next /Tune Up 4. Volume Down Volume Up 5. ZONE A/B/C Button Rear View 1 2 4 5 6 1.TV Audio In Jacks 2.DVD Audio In Jacks 3.Antenna Jack 4.EXT IR (External Remote Sensor) Jack 5.VIDEO Out Jack x 4 6.VIDEO In Jack 7.External Subwoofer Connector 8.Optical In Power Jack 9.Speaker/Power Wire Socket SPEAKER/POWER WIRE SOCKET DIAGRAM 10A FUSE SPEAKER (6X4-ohms) WIRING COLOR CODE GUIDE 12V DC Power Extension CAUTION! Connecting the speakers incorrectly will cause distortion and damage the power amplifier. RED - POWER IN 12V + BLACK - POWER GND 10A FUSE GREEN/BLACK - C LEFT RED - POWER IN 12V + 10A FUSE VIOLET - C RIGHT + BLACK - POWER GND GREEN - C LEFT + WHITE - B LEFT + VIOLET/BLACK - C RIGHT - BLUE/BLACK - A RIGHT - GRAY/BLACK - B RIGHT - WHITE/BLACK - B LEFT - ORANGE - A LEFT + BLUE - A RIGHT + GRAY - B RIGHT + ORANGE/BLACK - A LEFT - REMOTE CONTROL 1. POWER button 2. Bluetooth Mode Switch button POWER 3. AUX IN Mode Switch button 4. TV Mode Switch button 5. TUNE - / 14 BT USB ZONE B AUX IN FM ZONE C TV DVD 15 /TUNE+ button 16 6. VOL ( Volume )+/- buttons 7. OPTICAL ZONE A ( Play/Pause )/ ( Memory/ Preset /Preset Play )button 10 8. OPTICAL Mode Switch button 9. USB Mode Switch button 10. FM Mode Switch button 11. DVD Mode Switch button റͬറTUN- റͬറTUN+ VOL- VOL+ റͬറ PAIR 11 MUTE 12 12. MUTE button 13 13. PAIR button 14. ZONE A button 15. ZONE B button 16. ZONE C button EXT IR (External Remote Sensor) Jack on rear panel If using external remote sensor, insert the plug into the EXT IR Jack as the arrowhead shown on above picture. BATTERY INSTALLATION--- REMOTE CONTROL Battery Installation 1.Slide and lift the battery door (Figure 1). 2.Install 2 (two) AAA size batteries into the battery compartment as indicated by the polarity markings (Figure 2). 3.Replace the battery door (Figure 3). Battery Precaution Remote Control Effective Range When there is an obstacle between the unit and the remote control, the remote control may not operate properly. When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shines on the remote control of the unit, the remote control may not operate properly. GENERAL OPERATIONS 1. Press the Power button on the unit or remote control to power on the unit from standby mode. 2. Press the SOURCE button repeatedly to switch to desired mode as the following. BT TV AUX FM OPTICAL USB 3. During Playback: ~ Press the VOL (Volume)-/+ buttons to adjust volume level as desired. ~ Press Mute button on the Remote Control to mute the sound on all active zones. Press again to resume. ~ Press ZONE A, ZONE B or ZONE C button on the Remote Control or on front panel to switch ON or OFF the corresponding ZONE A/B/C speakers. 4. When finished listening, press the Power button to power off the unit. 5. If the unit is not used for long period of time, please disconnect power. 10 LISTEN TO FM RADIO 1. Power ON the unit. 2. Press the SOURCE button repeatedly until FM appears on the display. Or press FM on Remote Control. 3. Press and hold the /TUNE - or /TUNE + buttons and then release, The unit will start to search next ( or previous ) available FM radio station then plays. 4. When a station searched, press and hold the റͬറ button to display the desired storage location(such as Pxx.), then press റͬറ button to change the storage lacation, press and hold the റͬറ button to complete station storage. A total of 10 stations can be stored into the unit's memory. 5. Press റͬറ button on remote control to play the preset stored station. FM Antenna Insert the Antenna into the ANTENNA Jack on rear panel shown on right picture. The antenna wire on the rear of the unit is for radio reception. If reception is weak, unwind and extend the wire or relocate the wire to improve the radio reception. BLUETOOTH PAIRING AND PLAYBACK Pairing the unit to external BT Device as follows: 1. Power ON the unit. 2. Press the SOURCE button repeatedly until "BT" appears on display and flash. Or press BT button on Remote Control. 3. Turn on the external BT Device and enter BT searching mode. Start pairing as the screen instructions on the external BT Player. ( For details pairing procedures, please refer to the user's manual of your BT Device. ) Notes: ~ When the external BT Device searched the unit, "WMSMCZ3" will appear on the display of the external BT Device. ~ Pairing code "0000" may need to be entered. 4. After successfully paired and connected, the "BT" on display will stay lit. Normal operation after paired: ~ Press the VOL (Volume)-/+ buttons to adjust volume level as desired. 5.Disconnect the current pairing and connection by pressing the PAIR button on the unit or on remote control, and try to pair and connect with other external BT device. 11 ADDING OPTIONAL EXTERNAL SUBWOOFER NOTE: Before connecting, disconnect power. 1. Connect one end of subwoofer connection cable ( not supplied ) to the "+" Jack on the rear of the unit as the figure above. 2. Connect the other end to the "-" Jack on the rear of the unit as the figure above. 3. Power ON the unit. 4. Play the music as usual and set the desired volume. 12 CONNECT USING OPTICAL Optical Cable(Not Supplied) DVD or TV NOTE: Before connecting, disconnect power. 1. Connect one end of optical connection cable ( not supplied ) to the optical jack on the rear of the unit as pictured above. 2. Connect the other end to the DVD or TV back panel. 3. Power ON the unit. 4. Press the SOURCE button repeatedly until the "OPTICAL" appears on display. Or press OPTICAL button on Remote Control. 5. Play the music as usual and set the desired volume. NOTE: If there is no audio output (only picture) when your TV or DVD player is connected to the unit, please check DVD audio setting, and set the digital output to PCM format as below example picture. Picture Audio Sound Mode Bass Treble Balance Surround AVL Digital Output Audio Language Select Time Setup Lock Off MENU Exit Standard Off Off PCM English Move 13 CONNECT TO TV/DVD White MAIN TV Red Yellow Red White Yellow Yellow Yellow Yellow TV 2 TV 3 TV 4 DVD or TV NOTE: Before connecting, disconnect power. 1. Connect as the figure above.(TV 2, 3, 4 are optional to connect) 2. Power ON the unit. 3. Press the SOURCE button repeatedly until "TV" appears on display. TV audio is selected and will play through the unit. Or press TV button on Remote Control. 4. Press the SOURCE button repeatedly until "DVD" appears on display. DVD audio is selected and will play through the unit. Or press DVD button on Remote Control. 5. Play the audio or video as usual and set the desired volume. 14 AUX IN : LISTEN TO EXTERNAL AUDIO DEVICES To the Phones/Aux Out/Line Out Jack on the external audio device 1. Connect one end of audio connection cable (not supplied) to the AUX IN jack on the front of the unit as pictured above. 2. Connect the other end to the Audio out/Line out/Phone jack on the external player ( such as iPod, iPhone, iPad, MP3 player, Discman... etc. ) 3. Power ON the unit. 4. Press the SOURCE button repeatedly until "AUX" appears on display. Or press AUX IN button on Remote Control. 5. Play the music in the external player as usual and set the desired volume. USB : LISTEN TO EXTERNAL AUDIO DEVICES USB 1. Insert the USB as in the figure above. 2. Power ON the unit. 3. Insert the USB, then press the SOURCE button repeatedly until "USB" appears on screen. Or press USB button on Remote Control. 4. Play the music in the external player as usual and set the desired volume. NOTE: The USB port can also be used for charging. 15 TROUBLESHOOTING GUIDE Check the following guide before requesting service 6<03720 No power No sound 3266,%/(&$86( 3266,%/(628/7,21 power cable not connected or blown fuse ~Check fuse ~Check 12V connection Volume in minimum position Raise volume level by pressing the VOL (Volume) + button The connected device is not in playback mode Play the music/movie in the connected device as usual and make sure the volume level of it is in high level Input source incorrect Press the SOURCE button repeatedly to set the input source to the desired mode Bass level of the connected device too high Reduce the bass level of the connected device Volume level too high Reduce the volume level by pressing the VOL (Volume ) - button The batteries are consumed Replace with new batteries Sound distortion Remote not working Bluetooth reception failure The external device is too far from the unit Move the external BT device closer to the unit Pair both units Have not paired 16 SPECIFICATIONS Operation Voltage...........................................................................................................DC10V-14V Power Supply Requirement................................................................DC 12 Volts, Negative Ground Overall Dimension..................................................................................813(W)x107.2(H)x83(D)mm Max Power Consumption...........................................................................................................90W Video In/Out Level...........................................................................1 Vp-p/Load impedance:75 ohm Radio Coverage ...............................................................................................FM 87.5 -108.0 MH z Bluetooth Effective Range.............................................................................................Up to 30 feet (Measured in open area. Wall and structures may affect the effective range.) Remote Effective Range................................................................................................Up to 15 feet NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE. 17 www.riverparkinc.com C 2015 RIVERPARK Inc. V. 071015
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : Test Create Date : 2015:08:28 19:19:05+08:00 Modify Date : 2015:08:28 19:19:05+08:00 XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Metadata Date : 2015:06:23 11:08:15+08:00 Format : application/pdf Creator : Test Title : untitled Producer : Acrobat Distiller 11.0 (Windows) Document ID : uuid:ee895f37-5f5f-4ab5-8d5d-c8bbf00b9055 Instance ID : uuid:9f294c53-6594-4286-9cf9-e55cb1104c8e Page Count : 18EXIF Metadata provided by EXIF.tools