Junlan Electronic SBB55166 37 INCH STEREO SOUND BAR SYSTEM with Digital Optical Input and Bluetooth Wireless Technology User Manual 1

Shenzhen Junlan Electronic Ltd 37 INCH STEREO SOUND BAR SYSTEM with Digital Optical Input and Bluetooth Wireless Technology 1

User Manual

Size: 148.5(W) x 210(H)mm (A5)
  WARNING:Changes or modifications to this unit  not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonable protection against harmful interferencein a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to  try to correct theinterference by one or more of the following measures:     •Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help. •••FCC WarningsFCC NOTICE:To assure continued compliance, follow the attached installation instructions and use only shielded cables when connecting to other devices. Modifications not authorized by the manufacturer may void user’s authority to operate this device.2IMPORTANT SAFETY INSTRUCTIONSFCC ID:OKUSBB55166
3IMPORTANT SAFETY INSTRUCTIONS
NOTES:1. Insert the small plug from the supplied AC/DC Adapter to the DC IN Jack on the rear of unit.2. Connect the AC/DC Adapter to the wall outlet having AC 100-240V~;  50/60Hz.To the wall outletThis AC/DC Adaptor intended to be correctly orientated in a vertical or floor mount position.To save energy, unplug the AC/DC Adaptor from the wall outlet if you may not use the unit for an extended period of time.    4POWER SOURCEThe Red Standby Indicator on the front of unit will illuminate.DC INDC      9V,1.5ATo the DC IN jack on the rear of the unit.Remove and discard the insulation film as illustrated on the right.RELE ASEPUSHOPENR2025C+SNFig.1 Fig.2 Fig.3If the button cell is drained, replace it by a new one as below:1. Push and slide out the battery holder as Fig.1 below.2. Replace the button cell with a new CR2025 button cell as the polaritymarkings on the rear of the Remote Control as Fig.2 below.3. Close the battery holder as Fig.3 below.Follow these Battery Precaution when using a battery in this device:1. Use only the size and type of battery specified.BATTERY PRECAUTIONS:2. Be sure to follow the correct polarity when installing the battery as indicated in the battery compartment. A reversed battery may cause damage to the device.3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.Main  Unit:Remote  Control:
51. Placing on the table2. Mounting the Speaker Bar onto a wallDistance Between Two Brackets2-3 inchesINSTALLATIONWhen placing the Sound Bar on an entertainment center, bookshelf, or any type of enclosedspace, be sure to allow at least 2-3 inches of space around the Sound Bar for ventilation. If theSound Bar is enclosed in a tight space, without ventilation, heat generated from the Sound Barcould produce a potential heat hazard.24.9 inchesWe recommend having this unit professionally mounted. By using wall mounting accessories,the unit can be mounted onto a wall.AUX INLINE INL ROPTICAL INDC INDC      9V,1.5 A6. Do not dispose of battery in fire. Battery may explodes or leak.7. Clean the battery contacts and also those of the device prior to battery installation.4. If the batteries in the device are consumed or the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.5. Do not try to recharge the battery not intended to be recharged; it can overheat and rupture. (Follow battery manufacturer’s instructions.)8.            This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burn in just 2 hours and can lead to death.Keep new and used batteries away from children. If the battery compartment does not closesecurely, stop using the product and keep it away from children.If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Mounting to a wall2.1 Mountingto a wooden wall2.2 Mountingto a brick wall(1) (2)24.9 inches24.9 inches6A. Mark the position of the mounting screws on the wall using a pencil (not included).B. Drill the supplied mounting screws directly into the marks that you have made on the walland leave approx. 0.3 inches length to hook the sound bar.C. Put the sound bar onto the mounting screws. Make sure they are firm and stable.A. Mark the position of the supplied mounting screws on the wall using a pencil (not included).E. Put the sound bar onto the mounting screws. Make sure they are firm and stable.B. Drill 2 holes on wall with a powerful electric drill (not included).C. Insert the supplied plastic inserts into the holes by hammer (not included).D. Secure the supplied mounting screws into the plastic insert and leave approx. 0.3 inchlength to hook the sound bar.
7LOCATION OF CONTROLS123145678910 114. AUX IN Jack 7. DC IN Jack8. STANDBY/SOURCE Button9.      (Play/Pause) Button10.      (Volume Down/Skip Backward) Button11.      (Volume Up/Skip Forward) Button6. LINE IN Jacks5. OPTICAL IN Jack2. Indicators3. Remote Sensor1. SpeakersAUX INLINE INL ROPTICAL INDC INDC      9V,1.5AFront  View :Rear  View :Top  View :
8LOCATION OF CONTROLS - REMOTE CONTROL123457897.      (Mute) Button1.      (Standby On/Off) Button2.      (Play/Pause) Button3.      (Skip Backward) Button4. SOURCE Button5. VOL- (Volume Down) Button8.       (Skip Forward) Button9. VOL+ (Volume Up) ButtonEQ66. EQ (Equalizer) Button°30 °30Approx. 16 feetEFFECTIVE DISTANCE OF REMOTE TRANSMITTERWhen there is an obstacle between the unit and the transmitter, the unit may not operate.NOTES:When direct sunlight, an incandescent lamp, fluorescent lamp or any other strong light shineson the REMOTE SENSOR of the unit, the operation of the remote may be unstable.EQ
9OPERATIONS4. During playback: GENERAL OPERATION:1. Connected the unit to AC power as previously instructed. The Red Standby Indicator on the  front of unit will illuminate.2. Press the STANDBY/SOURCE Button on the top of unit or press the      Button on the RemoteControl to power on the unit from Standby mode. 3. Press the STANDBY/SOURCE Button on the top of unit or press the SOURCE Button on thethe front of unit will changes as your selection (see list below):BT (Bluetooth) BlueLINE IN   GreenAUX IN   Purple (Red + Blue Mixed)A. Press and release the     or     buttons on the unit or press the VOL + or VOL- buttons on the Remote Control repeatedly to adjust volume level as desired.B. Press the     (Mute) Button on the Remote Control to mute the sound temporary, press again to turn it back.5. When finished listening, press and hold the STANDBY/SOURCE Button on the top of unit approximately 2 seconds or press the     Button on the Remote Control to turn the unit to Standby mode. Playback Mode: Color of the INDICATOR on front panelRemote Control repeatedly to switch to desired playback mode. The color of the indicator on OPTICAL IN  Indigo (Blue + Green Mixed)C. Press the EQ (Equalizer) Button on the Remote Control repeatedly to select and set equalizer effects as desired. 6. To save energy, unplug the AC/DC Adaptor from the wall outlet if you may not use the unit foran extended period of time.
10First time use or re-pairing the unit to a new BT Device, pair as follows:3. If pairing is complete you may now play music with your external BT Device.4. During playback:If while pairing you are asked for a code please try "0000" or "1234".1. Power on the external BT Device and enter to BT mode.4. After pairing is complete, you may now play music with your external BT Device.BT MODE:BT (Bluetooth) pairing:Notes:Normal operation after pairing:1. Power on the unit and enter to BT mode as previously instructed. The color of the indicator on the front of unit will turn to blue and blink. 2. Power on the external BT Device and enter to BT searching mode. Start pairing following the on screen instructions from the external BT Device. After paired, the blue indicator will stop blinking.Press and hold the       or      buttons on the unit or press the        or        buttons on Remote Control repeatedly to skip tracks.When the external BT Device searched the unit, our model number "CHT988" will appear on  the display of external BT Device.2. Power on the unit and enter to BT mode as previously instructed. The color of the indicator on the front of unit will turn to blue and blink.3. Wait a few seconds until the unit is automatically paired to the external BT Device. The blue indicator will stop blinking.Press the      Button on the unit or Remote Control to pause, press again to resume normal playback.
11Line out jacks of TV L R VideoRedWhiteIN:Listen music from RCA output jacks from an external Video/Audio Player such as a Television;2. Connect the other end of the cable to the LINE IN Jacks on the rear of unit as illustrated below:1. Connect one end of the RCA Connection Cable (included) to the Line Out Jacks on theexternal Video/Audio Player.3. Power on the unit and enter to LINE IN mode as previously instructed. The color of the indicator on the front of unit will turn to Green. 4. Play the video/music on the connected Video/Audio Player as usual. (Make sure the volumelevel of the connected Video/Audio Player is turned to high level.)DVD Player, VCR … etc.LINEAUX INLINE INL ROPTICAL INDC INDC      9V,1.5ATo the LINE IN JacksSupplied RCA Connection CableTo  the Line Out Jacks on theexternal Video/Audio Player
Mobile PhoneConnect to the Phones; AUX Out;Line Out Jack of the external devices (Such like MP3 Player; cell phones;  iPod/iPad ... etc)MP3 Player12AUX IN :3. Power on the unit and enter to AUX IN mode as previously instructed. The color of theindicator on the front of unit will turn to Purple (Red + Blue Mixed).4. Play the music on the connected Audio Player as usual. (Make sure the volume level of theconnected Audio Player is turned to high level.)1. Connect one end of the Supplied Audio Connection Cable to the Line Out/AUX Out Jack on the external Audio Player.2. Connect the other end of the cable to the AUX IN Jack on the rear of unit as illustrated below: Listen music from an external Audio Player such as a MP3 Player, Discman … etc.AUX INLINE INL ROPTICAL INDC INDC      9V,1.5A....................................................................................................................................................................................................................................To AUX IN Jack
13Optical Connection CableTVListen music from the Optical Out Jack on an external Video Player or Television:OPTICAL IN:1. Connect one end of the Optical Connection Cable (not included) to the Optical Out Jack on the external Video Player or Television.2. Connect the other end of the cable to the OPTCAL IN Jack on the rear of unit as illustratedbelow:  3. Power on the unit and enter to Optical IN mode as previously instructed. The color of theindicator on the front of unit will turn to Indigo (Blue + Green Mixed).4. Plays the video on the connected Video Player or watching the TV program on the connected TV as usual.AUX INLINE INL ROPTICAL INDC INDC      9V,1.5AOPTICAL OUTTo the OPTCAL IN Jack To the Optical Out Jack on external Video Player or Television (Not included)
14Input source incorrectPress the STANDY/SOURCE Button onThe unit is in standby modeThe paired/connected deviceis not in playback modeThe external BT device istoo far from the unitRemote Controlnot functioning Out of  remote control rangeThe button cell in the Remote Controlare drainedPoint the remote control to the RemoteSensor on the unit within 16 feet, +/- 30degreeNo sound orsound weak Raise the volume level by press and SYMPTOM POSSIBLE CAUSE POSSIBLE SOLUTIONNo power The adapter is not connected Connect the adapter to the unit and wall outlet as page 4the unit or press the      Button on the Remote Control to power on the unitpress the VOL+ Button on Remote Controlon the unit or the  SOURCE Button on the Remote Control repeatedly to switch to desired mode press the VOL- Button on the Remote Press the STANDY/SOURCE Button1. To prevent fire or shock hazard, disconnect your unit from the AC wall outlet when cleaning.3. Mild soap and a damp cloth may be used.CLEANING:2. The finish on your unit may be cleaned with a dust cloth and cared for as other furniture. Use caution when cleaning and wiping the plastic parts.from standby moderelease the + Button on the top of unit orrepeatedly Reduce the volume level by press and release the - Button on the top of unit or Control repeatedlyVolume level too high Reduce the volume level of the paired/connected deviceReplace it by a new CR2025 button cellBT have not paired Pair the unit with the BT device as page 10Bluetooth not functioningPlace the external BT device close to theunitSound distortion/rattlePlay music/movie in the paired/connecteddevice as usual and make sure the volume level of it is in high levelVolume level in minimum positionTROUBLESHOOTING GUIDECLEANING
1 x AC/DC Adapter (Input: AC 100-240V~, 50/60Hz, 0.5A )(Output: DC         9V, 1500mA,           )1 x Remote Control, using CR2025 button cell ( Included, already installed )1 x Audio Connection Cable with 3.5mm Stereo Plugs15SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGEWITHOUT NOTICEPower Source...........................................................................................DC       9V, 1.5A,Bluetooth effective working range in open area............................................................up to 32 feetRemote effective working range....................................................................................up to 16 feet1 x Owner's ManualAudio Power..............................................................................5W per Channel (Total 10W, RMS) BT Version...................................................................................................................................4.12 x Plastic Inserts (For Wall Mounting)2 x Metallic Screws (For Wall Mounting)GENERAL SPECIFICATIONACCESSORIES1 x RCA Connection Cable

Navigation menu