Jvc Car Amplifier Ks Ax3101D Users Manual AX3104/KS AX3102/KS

Jvc-Ks-Ax3102-Instruction-Manual-772698 jvc-ks-ax3102-instruction-manual-772698

JVC Car Amplifier KS-AX3104 MA482ien

KS-AX3104 to the manual cd8b1c4a-7f51-44ce-af1a-308f5cade3e4

2015-01-26

: Jvc Jvc-Car-Amplifier-Ks-Ax3101D-Users-Manual-320115 jvc-car-amplifier-ks-ax3101d-users-manual-320115 jvc pdf

Open the PDF directly: View PDF PDF.
Page Count: 3

1
KS-AX3104
KS-AX3102
KS-AX3101D
POWER AMPLIFIER: INSTRUCTIONS
УСИЛИТЕЛЬ МОЩНОСТИ: ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ 1110NYMMDWTKK
EN, RU
© 2011 Victor Company of Japan, Limited
ENGLISH
Thank you for purchasing a JVC product.
If you have any questions or require information regarding installation kits, consult your “JVC IN-
CAR ENTERTAINMENT” or a company supplying the kits.
For safety....
• Stop the car before performing any complicated operations.
CAUTIONS AND NOTES
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems.
JVC recommends consulting a qualifi ed technician for installation.
• This unit uses BTL (Balanced Transformerless) amplifi er circuitry, i.e., fl oating ground system,
so comply with the following:
– Do not connect the “·” terminals of the speakers to each other.
– Do not connect the “·” terminals of the speakers to the metal body or chassis.
• Cover the unused leads with insulating tape to prevent them from short circuiting.
• When an extension lead is used, it should be as thick and short as possible; connect it fi rmly
with insulating tape.
• Be sure to leave an appropriate space between the antenna (aerial) and the wires of this unit.
• If the fuse blows, fi rst make sure the wires aren’t touching to cause a short circuit then replace
the old fuse with one with the same rating.
• Do not let pebbles, sand or metallic objects get inside the unit.
• To keep the heat dissipation mechanism running effectively, wipe the accumulated dust off
periodically.
• Listening to the tape, radio, CD or digital audio player, etc. with the volume set at a high level
for a long period of time will exhaust the battery, while the engine is turned off or while the
engine is idling.
• This unit becomes very hot. Be careful not to touch the unit not only when using but after using.
DO NOT disassemble the unit since there are no user serviceable parts inside.
INSTALLATION
The following illustration shows a typical installation. However, you should make adjustments
corresponding to your specifi c car.
Å Location of the unit
Under the front seat
Onto the trunk floor
• Mount this unit on a firm surface, such as in the
trunk or under the front seat.
• Since heat is generated in the unit, do not
mount it near inflammable objects. In addition,
mount it in an area that will not prevent the unit
from dissipating the heat.
• Do not mount the unit in the places subject to
heat: near a radiator, in a glove compartment or
in insulated areas such as under a car mat that
will prevent the unit from dissipating heat.
• When mounting the unit under the front seat,
make sure that adjusting the seat position will
not catch any wire of the unit.
ı Install the unit
Provided screw
φ 4 × 20 mm (13/16 in.)
Drilled hole
• When mounting this unit, be sure to use the
provided screws.
• If any other screws are used, there is a risk of
loosening the unit or damaging the parts under
the car floor.
• Before drilling holes in the trunk to install the
unit, make sure that there is a sufficient space
under the trunk so that you do not drill holes in
the fuel tank, etc.
SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
This equipment has been designed and manufactured to meet international safety standards but, like any electrical
equipment, care must be taken if you are to obtain the best results and safety is to be assured.
DO read the operating instructions before you attempt to use the equipment.
DO ensure that all electrical connections (including the mains plug, extension leads and interconnections between
pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and
withdraw the mains plug when making or changing connections.
DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
DO be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any
way–switch off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for
unattended operation or has a standby mode. Switch off using the switch on the equipment and make sure that your
family know how to do this. Special arrangements may need to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic
safety. It is illegal to watch television whilst driving.
DON’T listen to headphones at high volume as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings. Overheating will cause
damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws–to ensure complete safety always fit the
manufacturer’s approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
— NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case — this could
result in a fatal electrical shock.
— NEVER guess or take chances with electrical equipment of any kind–it is better to be safe than sorry!
E43486-340B
POWER SUPPLY
To metallic body or chassis
(To an accessory terminal)
Fuse*
Car battery
Ignition switch
JVC car receiver, etc.
Remote turn-on line
KS-AX3102
KS-AX3104
KS-AX3101D * Not Supplied
Caution
To prevent short circuits while making connections, keep the battery’s negative terminal
disconnected.
• When using a power cord (purchased separately), be sure to place the fuse near the battery as
shown.
• Connect the lead wire (power cord) through which power is supplied directly to the battery’s
“ª” terminal only after all the other connections have been made.
The proper lead wire connected to each POWER terminal is as follows.
• + B and GND: AWG 8 to AWG 4 (The cross section is about 8
mm2
to 21
mm2
.)
• REM: AWG 18 to AWG 8 (The cross section is about 0.8
mm2
to 8
mm2
.)
a When you use JVC car receiver with a remote lead, connect to the REM terminal on this unit.
b When you connect a unit without a remote lead, connect to the accessory circuit of the car
which is activated by the ignition switch. In this case, noise may occur when the car receiver
is turned on or off. To avoid this noise, do not turn on or off the car receiver itself. You can
turn on or off the car receiver along with the on/off operation of the ignition switch.
TERMINAL CONNECTIONS
When making terminal connections, properly fi x each terminal with the provided screw by turning
it as illustrated.
• Use ring terminals (not provided) for secure connection.
Notes
• Make sure the screw is fixed in place to prevent disconnections.
• Avoid over-tightening as it may cause the damage to the screw or its
head slot.
SPEAKER SYSTEMS
Notes
• Be sure not to connect the “·” terminals of the speakers to a common point.
• If the same lead is used for both left/right or front/rear speaker wirings, this unit cannot be used.
Always use the independent leads for each speaker. In this case, redo the wirings.
• Use the speakers with an impedance of 2 Ω to 8 Ω (4 Ω to 8 Ω: when used in Bridge Mode).
• Use the speakers which have sufficient capacity to the unit.
The proper lead connected to each SPEAKER OUTPUT terminal is as follows.
KS-AX3104/KS-AX3102: AWG 18 to AWG 12 (The cross section is about 0.8 mm2 to 3.3 mm2).
KS-AX3101D: AWG 18 to AWG 8 (The cross section is about 0.8 mm
2
to 8 mm
2
).
Dear Customer,
This apparatus is in conformance with the valid European directives and
standards regarding electromagnetic compatibility and electrical safety.
European representative of Victor Company of Japan, Limited is:
JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg
Germany
Information for Users on Disposal of Old Equipment and Batteries
[European Union only]
These symbols indicate that the product and the battery with this symbol should
not be disposed as general household waste at its end-of-life.
If you wish to dispose of this product and the battery, please do so in accordance
with applicable national legislation or other rules in your country and municipality.
By disposing of this product correctly, you will help to conserve natural resources
and will help prevent potential negative effects on the environment and human
health.
Notice:
The sign Pb below the symbol for batteries indicates that this battery contains lead.
Products
Battery
For Customer Use:
Enter below the Model No. and Serial No. which
are located on the top or bottom of the cabinet.
Retain this information for future reference.
Model No.
Serial No.
LVT2205-001A
[K/US]
KSAX310_EN_GE_NL_FR_UK_AR.indd 1KSAX310_EN_GE_NL_FR_UK_AR.indd 1 11/3/10 2:40:29 PM11/3/10 2:40:29 PM
2
SPEAKER CONNECTIONS
Connection varies depending on the number of the speakers used in your car. Select the
appropriate connection referring to the following diagrams.
Notes
• Securely connect all the parts. If the connections are loose, due to contact resistance etc., heat
will break out and may cause an accident.
• Run the connection leads under the car mats to prevent accidental disconnections.
Å When your receiver is equipped with line output.
ı When your receiver is NOT equipped with line output.
KS-AX3104
FRONT REAR
KS-AX3102
KS-AX3101D
• Connect each lead of the speaker input connector to a speaker positive lead or chassis*1 of the
receiver.
• Cover the terminals of unused speaker negative leads of the receiver with insulating tape to
prevent short circuits.
JVC car receiver, etc.
Rear ground terminal
Black lead of the speaker input connector
*1 Example: connecting to the ground
RECEIVER
GND
KS-AX3104
4-speaker system—Normal Mode
• Use the speakers with an impedance of 2 Ω to 8 Ω.
REAR
FRONT
FRONT REAR
CROSSOVER
OFF
LPF HPF OFF
LPF HPF
CROSSOVERHIGH INPUT
L/MONO L/MONO
INPUT
RR
HIGH INPUT
MIN MAX
LEVEL
MIN MAX
LEVEL
JVC car receiver, etc.
Front Front
Rear Rear
Line out
(Front)
Line out
(Rear)
*2*2
ı Speaker input connector.
Connector lead To Receiver Connector lead To Receiver
a White "FRONT LEFT (+)" =Front left (+) lead d Green "REAR LEFT (+)" =Rear left (+) lead
b Black "RECEIVER GND" =Chassis*1e Black "RECEIVER GND" =Chassis*1
c Gray "FRONT RIGHT (+)" =Front right (+) lead f Purple "REAR RIGHT (+)" =Rear right (+) lead
Å
2-speaker system plus subwoofer—Bridge Mode
• Use the speakers with an impedance of 2 Ω to 8 Ω.
• Use the subwoofer with an impedance of 4 Ω to 8 Ω.
REAR
FRONT
FRONT REAR
CROSSOVER
OFF
LPF HPF OFF
LPF HPF
CROSSOVERHIGH INPUT
L/MONO L/MONO
INPUT
RR
HIGH INPUT
MIN MAX
LEVEL
MIN MAX
LEVEL
JVC car receiver, etc.
Front Front
Subwoofer
Line out
(Front)
Line out (Rear) or
Subwoofer out
*2*2
ı Speaker input connector.
Connector lead To Receiver Connector lead To Receiver
a White "FRONT LEFT (+)" =Front left (+) lead d Green "REAR LEFT (+)" =Rear left (+) lead
b Black "RECEIVER GND" =Chassis*1e Black "RECEIVER GND" =Chassis*1
c Gray "FRONT RIGHT (+)" =Front right (+) lead f Purple "REAR RIGHT (+)" =Rear right (+) lead
Å
2-speaker system—Bridge Mode
• Use the speakers with an impedance of 4 Ω to 8 Ω.
• Be sure to connect the line output from the receiver to the left (L) jack on this unit.
REAR
FRONT
FRONT REAR
CROSSOVER
OFF
LPF HPF OFF
LPF HPF
CROSSOVERHIGH INPUT
L/MONO L/MONO
INPUT
RR
HIGH INPUT
MIN MAX
LEVEL
MIN MAX
LEVEL
JVC car receiver, etc. Front
Front
Line out
*2
ı Speaker input connector.
Connector lead To Receiver Connector lead To Receiver
a White "FRONT LEFT (+)" =Front left (+) lead d Green "REAR LEFT (+)" =Front right (+) lead
b Black "RECEIVER GND" =Chassis*1e Black "RECEIVER GND" =Chassis*1
c Gray "FRONT RIGHT (+)" =Front left (+) lead f Purple "REAR RIGHT (+)" =Front right (+) lead
Å
KS-AX3102
2-speaker system—Normal Mode
• Use the speakers with an impedance of 2 Ω to 8 Ω.
OFF
LPF HPF
CROSSOVER
INPUT
R
HIGH INPUT
MIN MAX
LEVEL
L/MONO
*2
JVC car receiver, etc.
Line out
ı Speaker input connector.
Connector lead To Receiver
a White "LEFT (+)" =Left (+) lead
b Black "RECEIVER GND" =Chassis*1
c Gray "RIGHT (+)" =Right (+) lead
Å
2-speaker system plus subwoofer
• Use the speakers with an impedance of 2 Ω to 8 Ω.
OFF
LPF HPF
CROSSOVER
INPUT
R
HIGH INPUT
MIN MAX
LEVEL
L/MONO
JVC car receiver, etc.
Line out
(Front)
ı Speaker input connector.
Connector lead To Receiver
a White "LEFT (+)" =Left (+) lead
b Black "RECEIVER GND" =Chassis*1
c Gray "RIGHT (+)" =Right (+) lead
Å
Line out (Rear) or
Subwoofer out
Subwoofer
JVC amplifier, etc.
(Purchased separately)
*2
*2
Subwoofer system—Bridge Mode
• Use the speakers with an impedance of 4 Ω to 8 Ω.
OFF
LPF HPF
CROSSOVER
INPUT
R
HIGH INPUT
MIN MAX
LEVEL
L/MONO
JVC car receiver, etc.
ı Speaker input connector.
Connector lead To Receiver
a White "LEFT (+)" =Left (+) lead
b Black "RECEIVER GND" =Chassis*1
c Gray "RIGHT (+)" =Right (+) lead
Å
Line out (Rear)
or
Subwoofer out
Subwoofer
*2
2-speaker system (2 amplifi ers)—Bridge Mode
• Use the speakers with an impedance of 4 Ω to 8 Ω.
• Be sure to connect the line output from the receiver to the left (L) jack on this unit.
OFF
LPF HPF
CROSSOVER
INPUT
R
HIGH INPUT
MIN MAX
LEVEL
L/MONO
OFF
LPF HPF
CROSSOVER
INPUT
R
HIGH INPUT
MIN MAX
LEVEL
L/MONO
JVC car receiver, etc.
ı Speaker input connector.
Connector lead To Receiver
a White "LEFT (+)" =Front left (+) lead
b Black "RECEIVER GND" =Chassis*1
c Gray "RIGHT (+)" =Front left (+) lead
Å
Line out
*2
ı Speaker input connector.
Connector lead To Receiver
a White "LEFT (+)" =Front right (+) lead
b Black "RECEIVER GND" =Chassis*1
c Gray "RIGHT (+)" =Front right (+) lead
KS-AX3101D
Subwoofer system
• Use the speakers with an impedance of 2 Ω to 8 Ω.
HIGH INPUTINPUT
R
L/MONO
PRE OUT
R
L
Line out (Rear)
or
Subwoofer out
JVC car receiver, etc.
ı Speaker input connector.
Connector lead To Receiver
a White "LEFT (+)" =Left (+) lead
b Black "RECEIVER GND" =Chassis*1
c Gray "RIGHT (+)" =Right (+) lead
Å
Subwoofer
*2
*2 Not supplied
KSAX310_EN_GE_NL_FR_UK_AR.indd 2KSAX310_EN_GE_NL_FR_UK_AR.indd 2 11/3/10 2:29:47 PM11/3/10 2:29:47 PM
3
SPECIFICATIONS
KS-AX3104 KS-AX3102 KS-AX3101D
Power Output
• Normal Mode:
Signal-to-Noise Ratio
60 W RMS × 4 channels at 4 Ω and ≤ 1% THD + N
76 dBA (reference: 1 W into 4 Ω)
65 W RMS × 2 channels at 4 Ω and ≤ 1% THD + N
76 dBA (reference: 1 W into 4 Ω)
250 W RMS × 1 channels at 4 Ω and ≤ 1% THD + N
60 dBA (reference: 1 W into 4 Ω)
Power Output
• Normal Mode: 90 W RMS × 4 channels at 2 Ω and ≤ 1% THD + N 90 W RMS × 2 channels at 2 Ω and ≤ 1% THD + N 400 W RMS × 1 channels at 2 Ω and ≤ 1% THD + N
• Bridge Mode: 150 W RMS × 2 channels at 4 Ω and ≤ 1% THD + N 150 W RMS × 1 channels at 4 Ω and ≤ 1% THD + N —
Maximum Power Output 800 W (400 W × 2) 400 W 800 W
Load Impedance
• Normal Mode: 4 Ω (2 Ω to 8 Ω allowance) 4 Ω (2 Ω to 8 Ω allowance) 4 Ω (2 Ω to 8 Ω allowance)
• Bridge Mode: 4 Ω (4 Ω to 8 Ω allowance) 4 Ω (4 Ω to 8 Ω allowance) —
Frequency Response 5 Hz to 50,000 Hz ( +0 dB, –3 dB) 5 Hz to 50,000 Hz ( +0 dB, –3 dB) 20 Hz to 200 Hz ( +0 dB, –3 dB)
Input Sensitivity/Impedance 2 V/21 kΩ (0.3 V to 6 V, variable) 2 V/21 kΩ (0.3 V to 6 V, variable) 2 V/40 kΩ (0.3 V to 6 V, variable)
Distortion Less than 0.04% (at 1 kHz) Less than 0.04% (at 1 kHz) Less than 0.08% (at 100 Hz)
Power Requirement DC 14.4 V (11 V to 16 V allowance) DC 14.4 V (11 V to 16 V allowance) DC 14.4 V (11 V to 16 V allowance)
Grounding system Negative ground Negative ground Negative ground
Dimensions (W×H×D) 335 mm × 51 mm × 212 mm
(13-4/16 in. × 2-1/16 in. × 8-6/16 in.)
202 mm × 51 mm × 212 mm
(8 in. × 2-1/16 in. × 8-6/16 in.)
222 mm × 51 mm × 212 mm
(8-12/16 in. × 2-1/16 in. × 8-6/16 in.)
Mass (approx.) 2.43 kg (5.3 lbs) 1.52 kg (3.4 lbs) 1.83 kg (4.0 lbs)
Accessories Speaker input connector 3P × 2
Mounting Screw
φ
4 × 20 mm (13/16 in.) × 4
Speaker input connector 3P × 1
Mounting Screw
φ
4 × 20 mm (13/16 in.) × 4
Speaker input connector 3P × 1
Mounting Screw
φ
4 × 20 mm (13/16 in.) × 4
Design and specifi cations are subject to change without notice.
CONTROLS
KS-AX3104
CROSSOVER
OFF
LPF HPF OFF
LPF HPF
CROSSOVER
POWER
HIGH INPUT
L/MONO L/MONO
HIGH INPUT
MIN MAX
LEVEL
MIN MAX
LEVEL
INPUT
FRONT REAR
KS-AX3102 KS-AX3101D
OFF
LPF HPF
CROSSOVER
POWER
MIN MAX
LEVEL
MIN MAX
LEVEL
MIN MAX
BASS BOOST
50Hz 200Hz
LPF
POWER
Å POWER indicator
The green lamp lights while the unit is turned on.
ı CROSSOVER filter switch
OFF: Normally set to this position. The switch is preset to this position when the unit is
shipped.
LPF: Set to this position when you want to turn on the LPF (Low-Pass Filter) switch. The Low-
Pass Filter transmits frequencies lower than 80 Hz.
HPF: Set to this position when you want to turn on the HPF (High-Pass Filter) switch. The
High-Pass Filter transmits frequencies higher than 150 Hz.
Ç Input LEVEL controller
The input level can be adjusted with this control when this unit is connected to other source
equipment. Adjust the level while listening to the sound. This control is preset to MIN when
the unit is shipped.
Î BASS BOOST controller
Turning this boosts the 45 Hz frequency within the range of 0 dB to +18 dB. Adjust the level
while listening to the sound. This controller is preset to MIN when the unit is shipped.
‰ LPF (Low-Pass Filter) controller
Adjust the cutoff frequency (the Low-Pass Filter transmits frequencies lower than the cutoff
frequency) within the range of 50 Hz to 200 Hz. Adjust the level while listening to the
sound. This controller is preset to 50 Hz when the unit is shipped.
TROUBLESHOOTING
The POWER indicator does not light.
• Change the fuses if the current one is blown.
• Connect the ground lead securely to a metal part of the car.
• Turn on the equipment connected to this unit.
• Confirm the battery voltage (11 V to 16 V).
• Use a relay if your system employs too many amplifiers.
• Leave the unit turned off to cool it down if it heats up abnormally.
No sound is heard.
• Confirm the connections for the power supply (see "POWER SUPPLY" on page 1).
• Connect the RCA pin cords to the INPUT jacks, or the speaker input connector to the HIGH
INPUT terminal.
• Confirm the speaker wirings and the position of the CROSSOVER filter switch (See “SPEAKER
CONNECTIONS” on page 2).
Alternator noise is heard.
• Keep the leads of the POWER terminals away from the RCA pin cords.
• Keep the RCA pin cords away from other electrical cables in the car.
• Connect the ground lead securely to a metal part of the car.
• Make sure the speaker negative leads do not touch the car chassis.
• Connect a bypass capacitor across the accessory switches (horn, fan, etc....).
Noise is made when you connect the unit to an AM (MW/LW) tuner.
• Move all the leads of this unit away from the antenna (aerial) lead.
KS-AX3101D
2-Subwoofer system (2 amplifi ers)
• Use the speakers with an impedance of 2 Ω to 8 Ω.
• Incoming signals from INPUT jacks are emitted through the PRE OUT jacks.
Line out (Rear)
or
Subwoofer out
JVC car receiver, etc.
ı Speaker input connector.
Connector lead To Receiver
a White "LEFT (+)" =Left (+) lead
b Black "RECEIVER GND" =Chassis*1
c Gray "RIGHT (+)" =Right (+) lead
Å
Subwoofer
*2
Subwoofer
*2
2-Subwoofer system
• Use the speakers with an impedance of 4 Ω to 8 Ω.
HIGH INPUT
INPUT
R
L/MONO
PRE OUT
R
L
Line out (Rear)
or
Subwoofer out
*2
JVC car receiver, etc.
ı Speaker input connector.
Connector lead To Receiver
a White "LEFT (+)" =Left (+) lead
b Black "RECEIVER GND" =Chassis*1
c Gray "RIGHT (+)" =Right (+) lead
Å
Subwoofer
Subwoofer
5-speaker system plus subwoofer—5.1-channel (3 amplifi ers)
• Use the speakers with an impedance of 2 Ω to 8 Ω.
• Be sure to connect the line output from the receiver to the left (L) jack on this unit.
HIGH INPUT
INPUT
R
L/MONO
PRE OUT
R
L
JVC car receiver, etc.
ı Speaker input connector.
Connector lead To Receiver
a White "LEFT (+)" =Left (+) lead
b Black "RECEIVER GND" =Chassis*1
c Gray "RIGHT (+)" =Left (+) lead
Å
Subwoofer
*2
JVC amplifier, etc.
(Purchased separately)
JVC amplifier, etc.
(Purchased separately) Center Speaker
Front
Speaker
Rear
Speaker
Line out (Front)
Line out (Rear)
*2
*2
*2
Line out
(Center)
Subwoofer out
KSAX310_EN_GE_NL_FR_UK_AR.indd 3KSAX310_EN_GE_NL_FR_UK_AR.indd 3 11/4/10 11:10:59 AM11/4/10 11:10:59 AM

Navigation menu