Jvc Mx Gt90 Users Manual GT90&80&70[J]Coverf

If not then 20920ien Manual: ://resources.jvc.com/Resources/00/00/98/20920ien

2015-01-23

: Jvc Jvc-Mx-Gt90-Users-Manual-325452 jvc-mx-gt90-users-manual-325452 jvc pdf

Open the PDF directly: View PDF .
Page Count: 34

Download
Open PDF In Browser	View PDF

COMPACT COMPONENT SYSTEM

MX-GT90
MX-GT80
MX-G70

— Consists of CA-MXGT90 and SP-MXGT90.
— Consists of CA-MXGT80 and SP-MXGT80.

— Consists of CA-MXG70 and SP-MXG70.

STANDBY/ON
PLAY & EXCHANGE

STANDBY

CD-R/RW PLAYBACK

MX-GT90

SP-MXGT90

CA-MXGT90

STANDBY/ON
PLAY & EXCHANGE

STANDBY

CD-R/RW PLAYBACK

MX-GT80

SP-MXGT80

CA-MXGT80

SP-MXGT80

STANDBY/ON
PLAY & EXCHANGE

STANDBY

CD-R/RW PLAYBACK

MX-G70

SP-MXG70

CA-MXG70

SP-MXG70

INSTRUCTIONS

For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.

GVT0052-001A
[J]

MX-GT90&80&70[J]Coverf

12/20/00, 11:03 PM

Warnings, Cautions and Others
Mises en garde, précautions et indications diverses

CAUTION

WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.

RISK OF ELECTRIC SHOCK
DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.

The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.

ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir
le coffret de l’appareil.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.

The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.

For U.S.A.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

For Canada/pour le Canada
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS
LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQUAU FOND.

Caution –– STANDBY/ON
button!
Disconnect the mains plug to shut the power off completely.
The STANDBY/ON
button in any position does not
disconnect the mains line. The power can be remote
controlled.
Attention –– Commutateur STANDBY/ON
button!
Déconnecter la fiche de secteur pour couper complètement
le courant. Le commutateur STANDBY/ON
ne coupe
jamais complètement la ligne de secteur, quelle que soit sa
position. Le courant peut être télécommandé.

1. CLASS 1 LASER PRODUCT
2. DANGER: Invisible laser radiation when open and interlock
failed or defeated. Avoid direct exposure to beam.
3. CAUTION: Do not open the top cover. There are no user
serviceable parts inside the Unit; leave all servicing to
qualified service personnel.
1. PRODUIT LASER CLASSE 1
2. ATTENTION: Radiation laser invisible quand l'appareil est
ouvert ou que le verrouillage est en panne ou désactivé.
Eviter une exposition directe au rayon.
3. ATTENTION: Ne pas ouvrir le couvercle du dessus. Il n'y a
aucune pièce utilisable à l'intérieur. Laisser à un personnel
qualifié le soin de réparer votre appareil.

For Canada/pour le Canada
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS
B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL
APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING
EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,”
ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE
BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS
NUMIRIQUES DE CLASSE B PRESCRITES DANS LA NORME
SUR LE MATERIEL BROUILLEUR: “APPAREILS NUMERIQUES”,
NMB-003
EDICTEE
PAR
LE
MINISTRE
DES
COMMUNICATIONS.

– G-1 –
MX-GT90&80&70[J]Safetyf

12/20/00, 11:04 PM

Instructions for safe use
(Statement in accordance with the UL standards)
1) Read Instructions — Read carefully this instructions for
your safe use before this appliance is installed, wireconnected, and operated.
2) Retain Instructions — For your future reference, retain
this instruction.
3) Follow Instructions — Follow and obey all warnings,
cautions and instructions marked on this appliance and
this instruction.
4) Water and Moisture — Do not expose this appliance to
rain, water and moisture, or operate it near water — for
example near a bathtub, wash bowl, kitchen sink,
laundry tub, in a wet basement or near a swimming pool,
and the like.

11) Outdoor Antenna Grounding — If this appliance is
provided with means to connect the outdoor antenna
and outside antenna is connected to this appliance, be
sure the antenna system is grounded so as to provide
some protection against voltage surges and built-up
static charges. Article 810 of the National Electrical
Code, ANSI/ NFPA 70, provides information with regard
to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antennadischarge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding
electrodes, and requirements for the grounding
electrode. Example of antenna grounding is illustrated in
here.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE

5) Ventilation and Heat — This appliance should be
situated so that its location does not interfere with its
proper ventilation. For example, this appliance should
not be situated on a bed, sofa, rug, or similar surface
that may block the ventilation openings; or, placed in a
built-in installation, such as a bookcase or cabinet that
may impede the flow of air through the ventilation
openings. This appliance should be situated away from
heat sources such as radiators, heat registers, stoves,
or other appliances (including amplifiers) that produce
heat.
6) Power sources — This appliance should be connected
to a power supply only of the type as marked on this
appliance.
7) Polarization — The precautions that should be taken so
that the polarization means of this appliance is not
defeated.
8) Power Cord Protection — Power supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the
appliance.
9) Cleaning — The appliance should be cleaned only as
recommended by the manufacturer.
10) Power Lines — An outdoor antenna should be located
away from power lines.

ANTENNA
LEAD IN
WIRE

GROUND
CLAMP

ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)

ELECTRIC
SERVICE
EQUIPMENT

GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)

NEC — NATIONAL ELECTRICAL CODE

12) Nonuse Periods — The power cord of the appliance
should be unplugged from the outlet when left unused
for a long period of time.
13) Object and Liquid Entry — Care should be taken so that
objects do not fall and liquids are not spilled into the
enclosure through openings.
14) Damage Requiring Service — The appliance should be
serviced by qualified service personnel when : (a) The
power-supply cord or the plug has been damaged; or (b)
Objects have fallen, or liquid has been spilled into the
appliance; or (c) The appliance has been exposed to
rain; or (d) The appliance does not appear to operate
normally or exhibits a marked change in performance; or
(e) The appliance has been dropped, or the enclosure
damaged.
15) Servicing — The user should not attempt to service the
appliance beyond that described in the operating
instructions. All other servicing should be referred to
qualified service personnel.

– G-2 –
MX-GT90&80&70[J]Safetyf

12/20/00, 11:04 PM

Introduction
We would like to thank you for purchasing one of our JVC products.
Before operating this unit, read this manual carefully and thoroughly to
obtain the best possible performance from your unit, and retain this manual
for future reference.
About This Manual

Power sources

This manual is organized as follows:

• When unplugging from the wall outlet, always pull the
plug, not the AC power cord.

• The manual mainly explains operations using the
buttons and controls on the unit. You can also use the
buttons on the remote control if they have the same or
similar names (or marks) as those on the unit.
If operation using the remote control is different from
that using the unit, it is then explained.
• Basic and common information that is the same for many
functions is grouped in one place, and is not repeated in
each procedure. For instance, we do not repeat the
information about turning on/off the unit, setting the
volume, changing the sound effects, and others, which are
explained in the section “Common Operations” on pages 9
to 11.
• The following marks are used in this manual:
Gives you warnings and cautions to prevent
from damage or risk of fire/electric shock.
Also gives you information which is not good
for obtaining the best possible performance
from the unit.

DO NOT handle the AC power cord with wet
hands.

Moisture condensation
Moisture may condense on the lens inside the unit in the
following cases:
• After starting heating in the room
• In a damp room
• If the unit is brought directly from a cold to a warm place
Should this occur, the unit may malfunction. In this case,
leave the unit turned on for a few hours until the moisture
evaporates, unplug the AC power cord, and then plug it in
again.

Others

Gives you information and hints you had better
know.

• Should any metallic object or liquid fall into the unit,
unplug the unit and consult your dealer before operating
any further.
• If you are not going to operate the unit for an extended
period of time, unplug the AC power cord from the wall
outlet.
DO NOT disassemble the unit since there are no
user serviceable parts inside.

Precautions

If anything goes wrong, unplug the AC power cord and
consult your dealer.

Installation
• Install in a place which is level, dry and neither too hot nor
too cold — between 5˚C (41˚F) and 35˚C (95˚F).
• Install the unit in a location with adequate ventilation to
prevent internal heat built-up in the unit.
• Leave sufficient distance between the unit and the TV.
• Keep the speakers away from the TV to avoid interference
with TV.
DO NOT install the unit in a location near heat
sources, or in a place subject to direct sunlight,
excessive dust or vibration.

–1–
EN01-12.MX-G90&80&70[J]f

12/20/00, 10:57 PM

Contents
Location of the Buttons and Controls ....................... 3
Front Panel ................................................................. 3
Remote Control .......................................................... 5

Getting Started ............................................................ 6
Supplied Accessories .................................................. 6
Putting the Batteries into the Remote Control ........... 6
Connecting Antennas ................................................. 6
Connecting Speakers .................................................. 7
Connecting Other Equipment ..................................... 8
Canceling the display demonstration ........................ 8

Common Operations .................................................. 9
Turning On or Off the Power ....................................... 9
Setting the Clock ........................................................ 9
Selecting the Sources................................................... 9
Adjusting the Volume ............................................... 10
Reinforcing the Bass Sound ..................................... 10
Selecting the Sound Modes ...................................... 10
Creating Your Own Sound Mode
— Manual Mode ................................................. 11

Listening to FM and AM Broadcasts ...................... 12
Tuning in a Station ................................................... 12
Presetting Stations .................................................... 12
Tuning in a Preset Station ........................................ 12

Playing Back CDs (CD/CD-R/CD-RW) .................. 13
Loading CDs ............................................................ 13
Playing Back the Entire Discs
— Continuous Play ............................................. 14
Basic CD Operations ................................................ 14
Programming the Playing Order of the Tracks
— Program Play ................................................. 15
Playing at Random — Random Play ....................... 16
Repeating Tracks or CDs — Repeat Play ................ 16
Prohibiting Disc Ejection — Tray Lock ................... 16

Playing Back Tapes ................................................... 17
Playing Back a Tape ................................................. 17
Locating the Beginning of a Song — Music Scan ... 17

Recording .................................................................. 18
Recording a Tape on Deck B ....................................
Dubbing Tapes ..........................................................
CD Direct Recording .................................................
Auto Edit Recording ..................................................

18
19
19
20

Using the Timers ....................................................... 21
Using Daily Timer ....................................................
Using Recording Timer ............................................
Using Sleep Timer ....................................................
Timer Priority ...........................................................

21
23
24
24

Maintenance .............................................................. 25
Troubleshooting ........................................................ 26
Specifications ............................................................. 27

–2–
EN01-12.MX-G90&80&70[J]f

12/20/00, 10:57 PM

Location of the Buttons and Controls
Become familiar with the buttons and controls on your unit.

Front Panel

1
STANDBY/ON

PLAY & EXCHANGE

STANDBY

3
4

u
i

CD-R/RW PLAYBACK

o
5

;
a

6
7
8

s
d

f
g
h

p
q
w
e
r

–3–
EN01-12.MX-G90&80&70[J]f

12/20/00, 10:57 PM

Continued

Display Window

6
7

See pages in the parentheses for details.

Front Panel
1 Disc trays
2 STANDBY/ON
button and STANDBY lamp
(9, 22, 23)
3 Remote sensor
4 PRESET + / – control (12)
4 / ¢ (reverse search/forward search) control
(9, 11, 14 – 16, 20 – 23)
5 Display window
6 TAPE 2 3 button and lamp (9, 17 – 19)
Pressing this button also turns on the unit.
7 CD 3¥8 (play/pause) button and lamp (9, 14 – 16, 20)
Pressing this button also turns on the unit.
8 FM/AM button and lamp (9, 12)
Pressing this button also turns on the unit.
9 AUX button and lamp (9)
Pressing this button also turns on the unit.
p CD play mode buttons
• REPEAT button (16)
• PROGRAM button (15)
• RANDOM button (16)
q CLOCK/TIMER button (9, 21 – 24)
w PHONES jack (10)
e CD REC START button (19, 20)
r EDIT button (20)
t Deck A cassette holder (17)
y 0 EJECT button for deck A (17)
u Disc number buttons and lamps (CD1, CD2, and CD3)
(14, 15, 19, 20)
Pressing one of these buttons also turns on the unit.
i SET/DISPLAY button (9, 11, 12, 15, 20 – 24)
o 0 (Disc tray open/close) (CD1, CD2, and CD3) buttons
(13, 14, 16)
Pressing one of these buttons also turns on the unit.
; CANCEL/DEMO button (8, 9, 16, 20 – 24)

a SOUND MODE control (10)
s SUBWOOFER LEVEL + / – control (10)
d TUNING + / – buttons (12)
1 / ¡ (fast left/fast right) buttons (11, 14, 17)
f VOLUME + / – control (10)
g 7 (stop) button (14 – 20, 23)
h Tape operation buttons
• TAPE A/B button (17)
• REVERSE MODE button (17, 19, 20)
• REC START/STOP button (18 – 20, 23)
j DUBBING button (19)
k Deck B cassette holder (17 – 20, 23)
l EJECT 0 button for deck B (17, 18)

Display Window
1 Timer indicators
•
(Timer), DAILY (Daily Timer), REC (Recording
Timer), and SLEEP (Sleeping Timer) indicators
2 Tape operation indicators
• A/B (operating deck),
(recording), 2 3 (tape
direction), and
(reverse mode) indicators
3 CD track number (1 – 16) indicators
4 Tuner operation indicators
• MONO and ST (stereo) indicators
5 Disc indicators
6 SOUND MODE indicator
7 CD play mode indicators
• REPEAT (ALL/1/DISC), PRGM (program), and
RANDOM indicators
8 SUBWOOFER LEVEL indicator
9 Main display
• Shows the source name, frequency, etc.
p Audio level indicator

–4–
EN01-12.MX-G90&80&70[J]f

12/20/00, 10:57 PM

Remote Control
Remote Control

8
9
p

q
w
e
r

3
4

t
y

1 Disc number buttons (CD1, CD2, and CD3)
(14, 15)
Pressing one of these buttons also turns on the unit.
2 Number buttons (12, 14, 15)
3 4 (reverse search) button (12, 14, 15, 17)
4 7 (stop) button (14 – 18, 20, 23)
5 REC START/STOP button (18 – 20)
6 SOUND MODE button (10)
7 FADE MUTING button (10)
8 STANDBY/ON
button (9)
9 SLEEP button (24)
p AUX button (9)
Pressing this button also turns on the unit.
q FM/AM button (9, 12)
Pressing this button also turns on the unit.
w FM MODE button (12)
e CD 3¥8 button (9, 14 – 16)
Pressing this button also turns on the unit.
r ¢ (forward search) button (12, 14 – 17)
t TAPE 2 3 button (9, 17, 18)
Pressing this button also turns on the unit.
y TAPE A/B button (17)
u SUBWOOFER LEVEL + / – buttons (10)
i VOLUME + / – buttons (10)

6
7

STANDBY/ON
PLAY & EXCHANGE

STANDBY

CD-R/RW PLAYBACK

When using the remote control, point it at
the remote sensor on the front panel.

–5–
EN01-12.MX-G90&80&70[J]f

12/20/00, 10:57 PM

Getting Started

Continued

Supplied Accessories

Connecting Antennas

Make sure that you have all the following items.
The number in the parentheses indicates the quantity of the
pieces supplied.

FM antenna

•
•
•
•

ENN

ANT

AM loop antenna (1)
FM antenna (1)
Remote control (1)
Batteries (2)

FM antenna (supplied)

EXT
AM LOOP

5
FM 7 IAL
X
COA

If anything is missing, consult your dealer immediately.

Putting the Batteries into the Remote Control
Insert the batteries — R6(SUM-3)/AA(15F) — into the
remote control, by matching the polarity (+ and –) on the
batteries with the + and – markings on the battery
compartment.
When the remote control can no longer operate the unit,
replace both batteries at the same time.

1 Attach the FM antenna to the FM 75 Ω
COAXIAL terminal.

2 Extend the FM antenna.
3 Fasten it up in the position which gives you
the best reception, then fix it on the wall, etc.

1
About the supplied FM antenna
The FM antenna supplied with this unit can be used as temporary
measure. If reception is poor, you can connect an outdoor FM
antenna.
R6(SUM-3)/AA(15F)

To connect an outdoor FM antenna
Before connecting it, disconnect the supplied FM antenna.
Outdoor FM antenna
(not supplied)

3
A

ENN

ANT

EXT
AM LOOP

• DO NOT use an old battery together with a
new one.
• DO NOT use different types of batteries
together.
• DO NOT expose batteries to heat or flame.
• DO NOT leave the batteries in the battery
compartment when you are not going to use
the remote control for an extended period of
time. Otherwise, it will be damaged from
battery leakage.

5
FM 7 IAL
X
COA

A 75 Ω antenna with coaxial type connector should be
used.

–6–
EN01-12.MX-G90&80&70[J]f

12/20/00, 10:57 PM

Connecting Speakers

AM antenna

For MX-GT90 and MX-GT80:
DO NOT carry the speaker by holding the duct
tube (on the top of the speaker).

ANTENNA

Vinyl-covered wire
(not supplied)

1
1

AM EXT
AM LOOP

2
FM 75
COAXIAL

Red
Speaker cords
(red/black)

SUBWOOFERS
LEFT

RIGHT

Black
AM loop antenna
(supplied)

Speaker cords
(red/black)

Black
RIGHT

LEFT
MAIN
SPEAKERS
CAUTION: SPEAKER
IMPEDANCE
6
16

1 Connect the AM loop antenna to the AM
LOOP terminals as illustrated.

Blue

• If the AM loop antenna wire is covered
with vinyl, remove the vinyl by twisting
it as shown in the diagram.

Speaker cords
(blue/black)

2 Turn the AM loop antenna until you have the
best reception.

From front
right speaker

From front
left speaker

To connect an outdoor AM antenna
When reception is poor, connect a single vinyl-covered wire
to the AM EXT terminal and extend it horizontally. (The AM
loop antenna must remain connected.)

From left
subwoofer

From right
subwoofer

For better reception of both FM and AM
• Make sure the antenna conductors do not touch any other
terminals and connecting cords.
• Keep the antennas away from metallic parts of the unit,
connecting cords, and the AC power cord.

–7–
EN01-12.MX-G90&80&70[J]f

12/20/00, 10:57 PM

1 Open the speaker terminals on the rear of the
unit.

To connect audio equipment with an optical digital
input terminal
You can record CD sound onto the connected digital
equipment.

2 Insert the end of the speaker cord into the
terminal.
Match the polarity (colors) of the speaker terminals: Red
(+) to red (+) and black (–) to black (–); Blue (+) to blue
(+) and black (–) to black (–).

CD OPTICAL
DIGITAL OUTPUT

Protective
plug

3 Close the speaker terminals.
Before connecting the
other equipment,
remove the protective
plug from the terminal.

IMPORTANT: Use only speakers with the same speaker
impedance as indicated by the speaker terminals on the
rear of the unit.

Connecting Other Equipment
Audio equipment with
an optical digital input

You can connect both analog and digital equipment.
• DO NOT connect any equipment while the power
is on.
• DO NOT plug in any equipment until all
connections are complete.

To optical digital input

Connect an optical digital cord (not supplied) between the
optical digital input terminal on the other equipment and the
CD OPTICAL DIGITAL OUTPUT terminal.

To connect an analog component
Be sure that the plugs of the audio cords are colored: White
plugs and jacks are for left audio signals, and red ones for
right audio signals.

Now, you can plug the AC power cord.
When connecting the AC power cord into a wall outlet, the
unit automatically starts display demonstration.
IMPORTANT: Be sure to check all connections to be done
before plugging the AC power cord into a wall outlet.

Audio equipment

Canceling the display demonstration

To audio output

On the unit ONLY:
For playing the other equipment through this unit,
connect between the audio output jacks on the other
equipment and AUX jacks by using audio cords (not
supplied).

To cancel the display demonstration, press
CANCEL/DEMO until “DEMO OFF” appears
on the display.

When you press other buttons
The display demonstration stops temporarily. It will start
automatically again (if no operation is done for 2 minutes) until you
cancel it by pressing CANCEL/DEMO.

To start the display demonstration manually
Press and hold CANCEL/DEMO again for more than 1
second.

–8–
EN01-12.MX-G90&80&70[J]f

12/20/00, 10:57 PM

Common Operations
Turning On or Off the Power

3 Turn 4 / ¢ to adjust the minute, then

To turn on the unit, press
STANDBY/ON
so that the
STANDBY lamp goes off.

STANDBY/ON

To turn off the unit (on standby), press
STANDBY/ON
again so that the
STANDBY lamp lights up.

STANDBY/ON

press SET/DISPLAY.
STANDBY

To check the clock time
STANDBY

Press and hold SET/DISPLAY while playing any source.
• Each time you press and hold the button, the source
indication and the clock time alternate on the display.

To adjust the clock again

A little power is always consumed even while the unit is on
standby.
To switch off the power supply completely, unplug the AC
power cord from the AC outlet.

If you have adjusted the clock before, you need to press
CLOCK/TIMER repeatedly until the clock setting mode is
selected.
• Each time you press the button, the clock/timer setting
modes change as follows:

When you unplug the AC power cord or if a power
failure occurs
The clock is reset to “AM 12:00” right away, while the tuner preset
stations (see page 12) will be erased in a few days.

DAILY
Canceled

REC

ON TIME
Clock
setting

ON TIME

(The hour digits start flashing.)

Setting the Clock
Before operating the unit any further, first set the clock built
in this unit.
You can set the clock whether the unit is on or off.

On the unit ONLY:

1 Press CLOCK/TIMER.
The hour digits start flashing on the display.

When you unplug the AC power cord or if a power
failure occurs
The clock loses the setting and is reset to “AM 12:00.” You need to
set the clock again.

Selecting the Sources
To listen to the FM/AM broadcasts, press FM/AM. (See
page 12.)
To play back CDs, press CD 3¥8. (See pages 13 – 16.)
To play back tapes, press TAPE 2 3. (See page 17.)
To select the external equipment as the source, press AUX.

2 Turn 4 / ¢ to adjust
the hour, then press
SET/DISPLAY.
The minute digits start flashing on the
display.

If you want to correct the
hour after pressing
SET/DISPLAY, press
CANCEL/DEMO. The hour
digits start flashing again.

When you press the play button for a particular source
(FM/AM, CD 3/8, TAPE 2 3, and AUX), the unit turns on
(and the unit starts playing the source if it is ready —
COMPU PLAY CONTROL).

About the audio level indicator
All the audio level indicators light up when no signals come in.

–9–
EN01-12.MX-G90&80&70[J]f

12/20/00, 10:58 PM

Continued

Adjusting the Volume

Selecting the Sound Modes

You can adjust the volume level only while the unit is turned
on. The volume level can be adjusted in 32 steps (VOL MIN,
VOL 01 — VOL 30, and VOL MAX).

You can select one of the 6 preset sound modes (3 surround
modes and 3 SEA — Sound Effect Amplifier — modes). This
function only affects the playback sound, but does not affect
your recording.

Turn VOLUME + / – clockwise (+) to
increase the volume or
counterclockwise (–) to decrease it.

To select the sound modes, turn
SOUND MODE (or press
SOUND MODE on the remote control)
until the sound mode you want appears on
the display.

When using the remote control, press VOLUME + to increase
the volume or press VOLUME – to decrease it.

The SOUND MODE indicator
also lights up on the display.

For private listening
Connect a pair of headphones to the PHONES jack. No sound
comes out of the speakers. Be sure to turn down the volume before
connecting or putting on headphones.
DO NOT turn off (on standby) the unit with the
volume set to an extremely high level; otherwise, a
sudden blast of sound can damage your hearing,
speakers and/or headphones when you turn on the
unit or start playing any source next time.
REMEMBER you cannot adjust the volume level
while the unit is on standby.

• The sound modes change as follows:
D.CLUB
OFF

(Canceled)

STADIUM

ROCK
POP
CLASSIC

MANUAL 3
MANUAL 2
MANUAL 1
* When using the remote control, the sound mode changes in
only one way.

To turn down the volume level temporarily
Press FADE MUTING on the remote control.
The volume level gradually decreases to
“VOL MIN.”

Surround modes **:
D.CLUB: Increases resonance and bass.
HALL:
Adds depth and brilliance to the sound.
STADIUM: Adds clarity and spreads the sound, like in an
outdoor stadium.

To restore the sound, press the button again.

Reinforcing the Bass Sound
You can select one of the 4 subwoofer levels. This function
only affects the playback sound, but does not affect your
recording. The subwoofer level can be adjusted in 4 steps —
LEVEL 1, LEVEL 2, LEVEL 3, and LEVEL 4 (MAX
LEVEL).
Turn SUBWOOFER LEVEL + / –
clockwise (+) to increase the subwoofer
sound or counterclockwise (–) to
decrease it.
When using the remote control, press
SUBWOOFER LEVEL + to increase the subwoofer volume
or press SUBWOOFER LEVEL – to decrease it.
SUBWOOFER indicator always lights up
when the unit is on.

HALL

(Dance CLUB)

SEA (Sound Effect Amplifier) modes:
ROCK:
Boosts low and high frequency. Good for
acoustic music.
POP:
Good for vocal music.
CLASSIC: Good for classical music.
Manual modes:
MANUAL 1/2/3:
Your individual mode stored in memory. See
“Creating Your Own Sound Mode — Manual
Mode.”
OFF:

Cancels the sound mode. The SOUND MODE
indicator goes off from the display.

** Surround elements are added to the SEA elements to create a
being-there feeling in your room.
When one of these modes is selected, the SOUND MODE
indicator lights up as —
While one of the SEA modes including manual modes (SEA
elements without surround elements) is selected, the SOUND
MODE indicator lights up as —

– 10 –
EN01-12.MX-G90&80&70[J]f

12/20/00, 10:58 PM

Creating Your Own Sound Mode
— Manual Mode

4 Press SET/DISPLAY again.

You can change SEA pattern to suit your preference. These
changed settings can be stored in the MANUAL 1,
MANUAL 2, and MANUAL 3 modes.
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start from step 1
again.

5 Turn

On the unit ONLY:

4 / ¢ to select one
of the MANUAL 1, 2, and 3
modes into which you want
to store the SEA pattern.

1 Select one of the preset sound modes.
• If you want to add the surround elements in your
SEA pattern, select one of the surround modes
(D.CLUB, HALL, or STADIUM) before starting the
procedure below. (See “Selecting the Sound Modes” on
page 10.)

6 Press SET/DISPLAY again.

2 Press and hold SET/DISPLAY
until “SEA CONT” appears on
the display.
The SEA pattern you have created are stored into the
MANUAL mode selected in the above step.

To use your own sound mode
Select MANUAL 1, MANUAL 2, or MANUAL 3 mode
when using the sound modes. See “Selecting the Sound
Modes” on page 10.

When you unplug the AC power cord or if a power
failure occurs
The setting will be erased in a few days. If this happens, set the
manual sound modes again.
Current level appears.

3 Adjust the SEA pattern.
1) Turn 4 / ¢ to select
the frequency range to
adjust (LOW, MID,
HIGH).
2) Press 1 or ¡ to
adjust the level (–3 to +3) of
the selected frequency
range.
3) Repeat steps 1) and 2) to
adjust the level of the other
frequency ranges.

– 11 –
EN01-12.MX-G90&80&70[J]f

12/20/00, 10:58 PM

Listening to FM and AM Broadcasts
Tuning in a Station

On the unit ONLY:

1 Press FM/AM.

1 Tune in the station you want to preset.
• See “Tuning in a Station.”

The unit automatically turns on and
tunes in the previously tuned station
(either FM or AM).
• Each time you press the button, the
band alternates between FM and AM.

2 Press SET/DISPLAY.

2 Start searching for stations.
On the unit:
Press and hold TUNING +
or TUNING – for more than
1 second.
On the remote control:
Press and hold ¢ or 4
for more than 1 second.

3 Turn PRESET + / – to select a
preset number.

4 Press SET/DISPLAY again.

The unit starts searching for stations
and stops when a station of sufficient
signal strength is tuned in.
• If a program is broadcast in stereo, the ST (stereo)
indicator lights up.

The tuned station in step 1 is stored in the
preset number selected in step 3.
• Storing a new station on a used number erases the
previously stored one.

To stop searching, press TUNING + or TUNING – (or ¢ /
4 on the remote control).
When you press TUNING + or TUNING – (or ¢ /
4 on the remote control) briefly and repeatedly
The frequency changes step by step.

When you unplug the AC power cord or if a power
failure occurs
The preset stations will be erased in a few days. If this happens,
preset the stations again.

To change the FM reception mode
When an FM stereo broadcast is hard to receive
or noisy, press FM MODE on the remote
control so that the MONO indicator lights up
on the display. Reception improves.
To restore the stereo effect, press FM MODE again so that
the MONO indicator goes off. In this stereo mode, you can
hear stereo sounds when a program is broadcasted.

Tuning in a Preset Station

Presetting Stations

2 Select a preset number.

1 Press FM/AM.
The unit automatically turns on and
tunes in the previously tuned station
(either FM or AM).
• Each time you press the button, the
band alternates between FM and AM.

You can preset 30 FM and 15 AM stations.
In some cases, test frequencies have been already memorized
for the tuner since the factory examined the tuner preset
function before shipment. This is not a malfunction. You can
preset the stations you want into memory by following the
presetting method.
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start from step 1
again.

On the unit:
Turn PRESET + / –.
On the remote control:
Press the number buttons.
Ex.: For preset number 5, press 5.
For preset number 15, press
+10 then 5.
For preset number 20, press
+10, then 10.
For preset number 25, press
+10, +10, then 5.
For preset number 30, press
+10, +10, then 10.

– 12 –
EN01-12.MX-G90&80&70[J]f

12/20/00, 10:58 PM

Playing Back CDs (CD/CD-R/CD-RW)
This unit has been designed to playback the following CDs:
• CD (Audio CD)
• CD-R (CD-Recordable)
• CD-RW (CD-ReWritable)

Loading CDs
On the unit ONLY:

1 Press 0 for the disc tray
(CD1, CD2, and CD3) you
want to load a CD onto.

Continued use of irregular shape CDs
(heart-shape, octagonal, etc.) can damage
the System.

The unit automatically turns on and
the disc tray comes out.

2 Place a disc correctly on the circle of the disc

General Notes

tray, with its label side up.

In general, you will have the best performance by keeping
your CDs and the mechanism clean.
• Store CDs in their cases, and keep them in cabinets or on
shelves.
• Keep the system’s disc trays closed when not in use.

CORRECT

• When using a CD single (8 cm), place it on the inner
circle of the disc tray.

When playing a CD-R or CD-RW
User-edited CD-Rs (CD-Recordable) and CD-RWs
(CD-ReWritable) can be played back only if they are already
“finalized.”
• You can play back your original CD-Rs or CD-RWs
recorded in music CD format. (However, they may not be
played back depending on their characteristics or recording
conditions.)
• Before playing back CD-Rs or CD-RWs, read their
instructions or cautions carefully.
• Some CD-Rs or CD-RWs may not be played back on this
unit because of their disc characteristics, damage or stain
on them, or the player’s lens is dirty.
• CD-RWs may require a longer readout time. This is caused
by the fact that the reflectance of CD-RWs is lower than for
regular CDs.

INCORRECT

3 Press the same 0 you have
pressed in step 1.
The disc tray closes, and the
corresponding disc number lamp and
disc indicator light up on the display
(CD1, CD2, and CD3).

4 Repeat steps 1 to 3 to place other CDs.
When loading more than one CD continuously
When you press 0 for the next tray you want to place another CD
onto, the first disc tray automatically closes and then the next tray
comes out.

About the disc indicators and disc number lamps
Each disc indicator corresponds to the disc tray of the same number.

Disc number
Disc indicator
Disc marker
• The disc marker lights up for the disc number you have selected.
• The disc indicator flashes while the corresponding CD is being
played.
• The disc indicators goes off when the unit has detected that there
is no CD on the corresponding disc tray.

– 13 –
EN13-17.MX-G90&80&70[J]f

12/21/00, 12:15 PM

Continued

Playing Back the Entire Discs
— Continuous Play

Basic CD Operations
While playing a CD, you can do the following operations.

1 Load CDs.
2 Press one of the disc number

To exchange CDs during playback of another
Press 0 corresponding to a CD, not playing or selected
currently, to eject and exchange the CD.
If you exchange CDs during play, the current play will not
stop until all CDs you have exchanged are played.

buttons (CD1, CD2, and
CD3) for the disc you want to
play.
CD play starts from the first track of
the selected disc and the disc number lamp starts flashing.
Tracks of the currently playing disc
(Track numbers exceeding 16 are not displayed.)

To stop play for a moment
Press CD 3¥8.
While pausing, the elapsed playing time
flashes on the display.
To resume playing, press CD 3¥8.

To go to another track

Track number

Elapsed playing time

• Pressing CD 3/8 instead of the disc number buttons
starts playing back if a CD is on the trays.
• If no CD is placed on the selected disc tray, “NO DISC”
appears on the display.
To stop playing, press 7.
To remove the disc, press 0 for the corresponding disc tray.

CD playback sequence
When 3 CDs* are loaded on the disc trays, they are played in one of
the following sequences.
• When CD1 is pressed: CD1 ] CD2 ] CD3 (then stops)
• When CD2 is pressed: CD2 ] CD3 ] CD1 (then stops)
• When CD3 is pressed: CD3 ] CD1 ] CD2 (then stops)
* When only 2 CDs are loaded, they are played in the same order,
but the disc tray without a CD is skipped.

Turn 4 / ¢ before or during
playback (or press 4 / ¢ on the
remote control).
• 4: Goes back to the beginning of
the current or previous tracks.
• ¢: Skips to the beginning of the
next or succeeding tracks.
If you turn 4 / ¢ (or press 4 / ¢ on the remote
control) before playing
You can change the tracks continuously.

To locate a particular point in a track
During play, press and hold 1 or ¡
(or 4 / ¢ on the remote control).
• 1 (or 4): Fast reverses the disc.
• ¡ (or ¢): Fast forwards the disc.

To go to another track directly using the number
buttons
Pressing the number button(s) on the remote control before or
during play allows you to start playing the track number you
want.
Ex.: For track number 5, press 5.
For track number 15, press +10,
then 5.
For track number 20, press +10,
then 10.
For track number 32, press +10,
+10, +10, then 2.

– 14 –
EN13-17.MX-G90&80&70[J]f

12/21/00, 12:15 PM

Programming the Playing Order of the Tracks
— Program Play
You can arrange the order in which tracks play before you
start playing. You can program up to 32 tracks.
• To use Repeat play (see page 16) for Program play, press
REPEAT after starting Program play.
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start from step 2
again.

5 Program other tracks you want.
• To program tracks from the same disc, repeat step 4.
• To program tracks from a different disc, repeat steps 3
and 4.

6 Press CD 3¥8.
The tracks are played in the order you
have programed.
To stop playing, press 7.

1 Load CDs.
• If the current playing source is not the CD player, press
CD 3¥8, then 7 before going to the next step.

To exit from Program play mode, press PROGRAM again
before or after play. The PRGM (program) indicator goes off.
The program you have made is stored in memory.

2 Press PROGRAM so that
“PROGRAM” appears on the
display.
The PRGM (program) indicator also lights up on the
display.

• If a program has been stored in memory, the program is
called up.

3 Press one of the disc number
buttons (CD1, CD2, and
CD3) to select the disc
number you want to play.
Track number

• If you try to program the 33rd track
“FULL” will appear on the display.
• If your entry is ignored
You have tried to program a track from an empty tray, or a track
number that does not exist on the CD (for example, selecting track
14 on a CD that only has 12 tracks). Such entries are ignored.
• If the total playing time is 100 minutes or more
“-- -- : -- --” will appear on the display.

To check the program contents
Before playing, you can check the
program contents by pressing ¢ or 4
on the remote control.
• ¢ : Shows the programed tracks in
the programed order.
• 4 : Shows them in the reverse order.

To modify the program

Disc number

Program step number

4 Select a track from the CD
selected in the above step.
On the unit:
Turn 4 / ¢ to select the
track number and press
SET/DISPLAY.
On the remote control:
Press the number buttons.
• For how to use the number buttons,
see “To go to another track directly
using the number buttons” on page 14.

Before or after playing, you can erase the last
programed tracks by pressing
CANCEL/DEMO.
• Each time you press the button, the programed
track shown on the display is erased from the
program.
• Ejecting a CD will also erase the track numbers
programmed from the ejected CD.
To add tracks in the program before playing, simply select
the track numbers you want to add by following step 4 of the
programming procedure on page 15.
To erase the entire program before or after playing, press
7. “PROGRAM” appears on the display.
The program you have made will be erased, when —
• You eject all the CDs.
• You unplug the AC power cord.
• A power failure occurs.

– 15 –
EN13-17.MX-G90&80&70[J]f

12/21/00, 12:16 PM

Playing at Random — Random Play

Repeating Tracks or CDs — Repeat Play

The tracks of all loaded CDs will play at random.
• To use Repeat play for Random play, press REPEAT after
starting Random play.

You can have all the CDs, the program or the individual track
currently playing repeat as many times as you like.

On the unit ONLY:

1 Load CDs.
• If the current playing source is not the CD player, press
CD 3¥8, then 7 before going to the next step.

2 Press RANDOM so that
“RANDOM” appears on the display.
The RANDOM indicator also lights up on the
display.

To repeat playing, press REPEAT during or
before play. To use Repeat play for Program
play and Random play, press the button after
starting playback.
• Each time you press the button, Repeat play mode changes
as follows, and the following indicator lights up on the
display:
REPEAT ALL
Canceled

REPEAT 1 DISC
REPEAT 1

REPEAT ALL:

Repeats all the tracks on all the CDs
(continuously or at random), or all the
tracks in the program.
REPEAT 1 DISC : Repeats all the tracks on one CD.
• REPEAT 1 DISC is not used for
Program play and Random play.
REPEAT 1:
Repeats one track on one CD.

3 Press CD 3¥8.
The tracks are played at random.
Random play ends when all the tracks
are played once.
To skip the currently playing track, turn 4 / ¢ to the
right (or press ¢ on the remote control).
Even if you turn 4 / ¢ to the left (or press 4 on
the remote control)
You cannot go back to the previous tracks during Random play.

To stop playing, press 7.
• Random play also stops when one of the disc trays is
opened.
To exit from Random play mode, press RANDOM again
before or after play.

To cancel Repeat play, press REPEAT repeatedly until the
REPEAT indicators go off from the display.
• Repeat play is also canceled when you select Program play
or Random play.

Prohibiting Disc Ejection — Tray Lock
You can prohibit CD ejection from the unit and lock CDs.
• This operation is possible only when the source is the CD
player.

On the unit ONLY:
To prohibit disc ejection, press 0 for
any disc tray while holding down 7. (If
there is any disc tray opened, close it
first.)
“LOCKED” appears for a while, and the
loaded CDs are locked.
To cancel the prohibition and unlock
the CDs, press 0 for any disc tray while
holding down 7.
“UNLOCKED” appears for a while, and
the loaded CDs are unlocked.

If you try to eject CDs
“LOCKED” appears to inform you that the Tray Lock is in use.

– 16 –
EN13-17.MX-G90&80&70[J]f

12/21/00, 12:16 PM

Playing Back Tapes
You can play back type I, type II, and type IV tapes without
changing any settings.

Playing Back a Tape

To play both sides repeatedly — Reverse Mode
Reverse Mode works for both decks at the same time.
When it is in use, the tape automatically reverses at the end of
a side and the unit starts playing for the other side of the tape,
and repeats the same process.
To use Reverse Mode, press
REVERSE MODE so that the Reverse Mode
indicator on the display lights up like —
.
To cancel Reverse Mode, press the button
again so that the Reverse Mode indicator on the
display lights up like — .

1 Press EJECT (0) for the deck you want to
use.

For Deck B
For Deck A

2 Put a cassette in with the exposed part of the

When Reverse Mode is on with cassettes in both decks
A and B
After the reverse (2) side of the tape finishes playing, the tape in the
other deck starts playing.

tape down.

Locating the Beginning of a Song
— Music Scan
You can use Music Scan to locate the beginning of a song.
Music Scan searches for blank portions that usually separate
recorded songs, then plays the next song.

3 Close the cassette holder gently.

To find the beginning of the current song
During play, press 1 or ¡ (4 or
¢ on the remote control) in the opposite
direction to the tape play.
The tape direction indicator of the opposite
direction to the tape play starts flashing
slowly.
Searching stops automatically at the beginning of the current
song, and the current song starts automatically.

If you put cassettes in both decks A and B, the last deck
you have put a cassette into is selected.
To select the other deck, press TAPE A/B.

4 Press TAPE 2 3.
The tape play starts and the tape
direction indicator (3 or 2) starts
flashing slowly to indicate the tape
running direction.
• Each time you press the button, the
tape direction changes.
3 : plays the front side.
2 : plays the reverse side.
• If no cassette is inserted, “NO TAPE” appears on the
display.
When the tape plays to the end, the deck automatically
stops if the Reverse Mode is not on. (See “To play both
sides repeatedly — Reverse Mode.”)

To find the beginning of the next song
During play, press 1 or ¡ (4 or
¢ on the remote control) in the same
direction as the tape play.
The tape direction indicator of the same
direction as the tape play starts flashing
slowly and quickly alternately.
Searching stops automatically at the beginning of the next
song, and the next song starts automatically.

To stop playing, press 7.
To operate the other deck, press TAPE A/B,
then TAPE 2 3.
To fast-wind to the left or to the right, press 1 or ¡
(4 or ¢ on the remote control) while the tape is not
running.
The tape direction indicator (2 or 3) starts flashing quickly
on the display.

Music Scan works by detecting a 4-second long blank
between each song, so it will not work well in the
following cases
• No blank at the beginning of a song.
• Noise (often caused by much use or poor quality dubbing) which
fills the blank.
• Long, very soft passages or pauses in a song.

To remove the cassette, press 0 EJECT for deck A or
EJECT 0 for deck B.

The use of the C-120 or thinner tape is not
recommended, since characteristic deterioration
may occur and this tape easily jams in the pinchrollers and the capstans.

– 17 –
EN13-17.MX-G90&80&70[J]f

12/21/00, 12:16 PM

Recording

Continued

Recording a Tape on Deck B

IMPORTANT:
• It should be noted that it may be unlawful to re-record
pre-recorded tapes, records, or discs without the
consent of the owner of copyright in the sound or video
recording, broadcast or cable programme and in any
literary, dramatic, musical, or artistic embodied
therein.
• The recording level is automatically set correctly, so it is
not affected by the VOLUME, the SUBWOOFER LEVEL,
and the SOUND MODE controls. Thus, during recording
you can adjust the sound you are actually listening to
without affecting the recording level.
• If recordings you have made have excessive noise or static,
the unit may be too close to a TV. Increase the distance
between the TV and the unit.
• You can use type I tape for recording.

1 Press EJECT 0 for the deck B.

2 Put a recordable cassette into deck B.
3 Close the cassette holder gently.
4 Check the tape direction of deck B.

• If the tape direction is not correct, press TAPE 2 3
twice then 7 to change the tape direction.

To protect your recording
Cassettes have two small
tabs on the back to protect
from unexpected erasure or
re-recording.
To protect your recording,
remove these tabs.
To re-record on a protected tape, cover the holes with
adhesive tape.

5 Start playing the source — FM, AM, CD
player, deck A, or auxiliary equipment
connected to AUX jacks.
• When the source is CD, you can also use CD Direct
Recording (see page 19) and Auto Edit Recording (see
page 20).
• When the source is deck A, you can also use the
dubbing method (see “Dubbing Tapes” on page 19).

To keep the best recording and playback sound quality
If the heads, capstans, and pinch rollers of the cassette decks
become dirty, the following will occur:
• Impaired sound quality
• Discontinuous sound
• Fading
• Incomplete erasure
• Difficulty in recording

6 Start recording.
On the unit:
Press REC START/STOP.
On the remote control:
Press and hold REC START/STOP
for more than 1 second.
The
(recording) indicator lights up on
the display and recording starts.
• If no cassette is inserted, “NO TAPE” appears on the
display. If a protected tape is inserted, “NO REC”
appears on the display.

To clean the heads, capstans, and pinch rollers
Use a cotton swab moistened with alcohol.
Pinch rollers
Capstans

To stop recording immediately, press 7.
To remove the cassette, press EJECT 0 for deck B.

Heads

To demagnetize the heads
Turn off the unit, and use a head demagnetizer (available at
electronics and audio shops).

– 18 –
EN18-26.MX-G90&80&70[J]f

12/20/00, 11:04 PM

CD Direct Recording

To record on both sides — Reverse Mode
Press REVERSE MODE so that the Reverse
Mode indicator lights up like —
.
• When using the Reverse Mode for recording,
start recording in the forward (3) direction
first. Otherwise, recording will stop when recording is done
only on one side (reverse) of the tape.
To cancel Reverse Mode, press the button again so that the
Reverse Mode indicator lights up like — .

Dubbing Tapes

Everything on the CD goes onto the tape in the order it is on
the CD, or according to the order you have made for Program
play.

On the unit ONLY:

1 Put a recordable cassette into deck B.
2 Load CDs.
3 Press one of the disc
number buttons (CD1,
CD2, and CD3) to select
the disc, then 7.

You can record from one tape to another.

On the unit ONLY:

• If you want to make a program, perform steps 2 to 5 on
page 15. After making a program, go to the next step.

1 Press TAPE 2 3, then 7.

4 Press CD REC START.
“CD REC” appears, and the
(recording) indicator lights up on the
display.
Deck B starts recording and the CD player starts playing.
When the recording is done, “CD REC FINISHED”
appears on the display, and the CD player and deck B
stop.

2 Put the source cassette in deck A, and a
recordable cassette into deck B.
• Put the cassettes in both decks so that the tapes will run
in the forward (3) direction.

3 Press DUBBING.
The
(recording) indicator lights up on
the display and dubbing starts.

To stop dubbing, press 7 so that both decks (A and B) stop.

To record on both sides — Reverse Mode
Press REVERSE MODE so that the Reverse
Mode indicator lights up like —
.
To cancel Reverse Mode, press the button
again so that the Reverse Mode indicator
lights up like — .

To stop recording, press REC START/STOP
or 7. So that a 4-second blank portion is
created on the recording tape. (Remember a 4second blank is important when using Music
Scan — see page 17.)

To record on both sides — Reverse Mode
Press REVERSE MODE so that the Reverse
Mode indicator lights up like —
.
• When using the Reverse Mode for CD Direct
Recording, start recording in the forward (3)
direction first. When the tape reaches its end while
recording a song in the forward direction (3), the last song
will be re-recorded at the beginning of the reverse side (2).
If you start recording on the reverse side (2), recording
will stop when recording is done only on one side (reverse)
of the tape.
To cancel Reverse Mode, press the button again so that the
Reverse Mode indicator lights up like — .

– 19 –
EN18-26.MX-G90&80&70[J]f

12/20/00, 11:04 PM

Auto Edit Recording

4 Press SET/DISPLAY.
• Each time you press the button, the tracks to
be recorded on the front side (“SIDE-A”)
and on the reverse side (“SIDE-B”) alternate.

By using Auto Edit Recording, you can record the CD tracks
to fit the tape. Auto Edit Recording makes a program by
selecting the CD tracks in numerical order. However, to
prevent the end of the last track on the front side from being
cut off, the last track is selected so as to fit on the remaining
tape length.

Tracks to be recorded on the
reverse side (SIDE-B) appear.

On the unit ONLY:

1 Load CDs.
• If the current playing source is not the CD player, press
CD 3¥8, then 7 before going to the next step.

2 Press EDIT.

5 Put a recordable cassette of appropriate
length into deck B.

6 Press REVERSE MODE so that
the Reverse Mode indicator lights
up like
.
• Without turning on the Reverse Mode
(
), recording will stop when the front
side of the tape is recorded.

3 Press the disc number

7 Press CD REC START.

button (CD1, CD2, and
CD3) for the disc you want
to record from.

“TAPE SIDE-A STAND-BY” appears,
and the
(recording) indicator lights
up on the display.
Deck B starts recording then, about 10 seconds later, the
CD player starts playing.
When the recording is done, “CD REC FINISHED”
appears on the display, and the CD player and deck B
stop.
• If a tape has not been rewound, deck B will rewind the
tape before it starts recording.
• A 10-second blank portion is automatically created at
the beginning of each side of the tape.

The optimum tape length for the disc appears.

To change the tape length manually
If the tape length selected is not satisfactory, you can
change the tape length by turning 4 / ¢ on the unit.
You can select the tape length among the following
— 40, 46, 50, 54, 60, 64, 70, 74, 80, 84, and 90.

To stop during Auto Edit Recording
Press REC START/STOP or 7. So that a 4-second blank
portion is created on the recording tape. (Remember a 4second blank is important when using Music Scan — see
page 17.)
To cancel Auto Edit Recording
Press CANCEL/DEMO or 7 before or after play.

– 20 –
EN18-26.MX-G90&80&70[J]f

12/20/00, 11:05 PM

Using the Timers
On the unit ONLY:

There are three timers available — Daily Timer, Recording
Timer, and Sleep Timer.
Before using the timers, you need to set the clock built in the
unit. (See page 9.)

1 Press CLOCK/TIMER repeatedly
until “DAILY” appears on the
display.
indicator lights up and DAILY (Daily
Timer) indicator also starts flashing on the
display.

Using Daily Timer
With Daily Timer, you can wake to your favorite music or
radio program. You can set the timer whether the unit is on or
off.

How Daily Timer actually works
The unit automatically turns on, set the volume level to the
preset level, and starts playing the specified source when the
on-time comes (the
indicator flashes just before the ontime, and continues flashing while the timer is operating).
Then, when the off-time comes (“OFF” flashes just before the
off-time), the unit automatically turns off (on standby).
The Daily timer works everyday automatically.
If you do not want to use the Daily timer, turn off the Daily
timer. (See “To turn on or off Daily Timer after its setting is
done” on page 22.)
The timer setting remains in memory until you change it.
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start from step 1
again.
• To correct a mis-entry while setting the timer, press
CANCEL/DEMO.

Before you start...
• When using the tuner as the source to play —
– Make sure to select a desired station.
• When using a CD as the source to play —
– Make sure there is a CD on the selected disc number
tray.
• When using a tape as the source to play —
– Make sure that a tape is in the deck whose deck
indicator (A or B) is lit on the display.
– Make sure that the tape direction is correct.
• When using the external component as the source to
play —
– Set the timer equipped on the external component at
the same time.

• Each time you press the button, the timer setting modes
change as follows:
DAILY
Canceled

REC

ON TIME
Clock
setting

ON TIME

(See page 9.)

2 Press CLOCK/TIMER again.
“ON TIME” appears for 2 seconds, then the
unit enters on-time setting mode.

3 Set the on-time you want the unit to turn on
at.
1) Turn 4 / ¢ to set the hour,
then press SET/DISPLAY.
2) Turn 4 / ¢ to set the minute,
then press SET/DISPLAY.
“OFF TIME” appears for 2
seconds on the display, then the
unit enters off-time setting mode.

4 Set the off-time you want the
unit to turn off (on standby)
at.
1) Turn 4 / ¢ to set the hour, then press
SET/DISPLAY.
2) Turn 4 / ¢ to set the minute, then press
SET/DISPLAY.
The unit enters source selecting mode.

– 21 –
EN18-26.MX-G90&80&70[J]f

12/20/00, 11:05 PM

Continued

5 Turn 4 / ¢ to select the source to play,

9 Press STANDBY/ON

to
turn off the unit (on standby)
if you have set the Daily Timer
with the unit turned on.

then press SET/DISPLAY.
• The source changes as follows:
TUNER FM
AUX

TUNER AM

TAPE

– CD

AM”
Turn 4 / ¢ to select the preset station number, then
press SET/DISPLAY.
The unit enters volume setting mode.

– –”

1) Turn 4 / ¢ to select the disc number, then press
SET/DISPLAY.
2) Turn 4 / ¢ to set the track number, then press
SET/DISPLAY.
The unit enters volume setting mode.

7 Turn 4 / ¢ to set the
volume level.
• The volume level changes as follows:
VOL 05

VOL 15

VOL 10

If the unit is turned on when the on-time comes
Daily Timer does not work.
Even if you unplug the AC power cord or if a power
failure occurs
Once you set the timer, the timer setting may remain stored in
memory in a few days. In this case, check whether the timer setting
still remains or not.

To turn on or off Daily Timer after its setting is done

6 When selecting “TUNER FM” or “TUNER

VOL – –

1 Press CLOCK/TIMER repeatedly until
“DAILY” appears on the display.
2 To turn off the Daily Timer, press
CANCEL/DEMO.
indicator and the DAILY (Daily Timer)
indicator go off from the display (“OFF”
appears for a while).
The Daily Timer is canceled, but the
setting for the Daily Timer remains in
memory.
To turn on the Daily Timer, press
SET/DISPLAY.
indicator and the DAILY (Daily Timer)
indicator light up on the display. The
settings you have done are shown on the
display in sequence for your confirmation.

• If you select “ VOL – –,” the volume is set to the last
level when the unit has been turned off.

8 Press SET/DISPLAY to complete
the Daily Timer setting.
The DAILY (Daily Timer) indicator stops
flashing and remains lit. The settings you
have done are shown on the display in
sequence.

– 22 –
EN18-26.MX-G90&80&70[J]f

STANDBY

––

TUNER FM: tunes into a specified preset FM station.
= go to step 6.
TUNER AM: tunes into a specified preset AM station.
= go to step 6.
– CD – –: plays a disc from a specified track of a
specified disc. = go to step 6.
TAPE:
plays a tape in deck A or B.
= go to step 7.
AUX:
plays an external source. = go to step 7.

When selecting “– CD

STANDBY/ON

12/20/00, 11:05 PM

4 Set the on-time you want the

Using Recording Timer

unit to turn on at.

With Recording Timer, you can make a tape of a radio
broadcast automatically. You can set the timer whether the
system is on or off.

1) Turn 4 / ¢ to set the hour,
then press SET/DISPLAY.
2) Turn 4 / ¢ to set the minute,
then press SET/DISPLAY.
“OFF TIME” appears for 2
seconds, then the unit enters offtime setting mode.

How Recording Timer actually works
The unit automatically turns on, tunes into the specified
station, sets the volume level to “MIN,” and starts recording
when the on-time comes (the
indicator flashes just before
the on-time, and continues flashing while the timer is
operating). Then, when the off-time comes (“OFF” appears
just before the off-time), the unit automatically turns off (on
standby).
The timer setting remains in memory until you change it.
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start from step 1
again.
• To correct a mis-entry while setting the timer, press
CANCEL/DEMO.

5 Set the off-time you want the
unit to turn off (on standby) at.
1) Turn 4 / ¢ to set the hour, then press
SET/DISPLAY.
2) Turn 4 / ¢ to set the minute, then press
SET/DISPLAY.
The unit enters preset station selecting mode.

6 Select the preset station.

1) Turn 4 / ¢ to select the band (“TUNER FM” or
“TUNER AM”), then press SET/DISPLAY.
2) Turn 4 / ¢ to select a preset channel number,
then press SET/DISPLAY.
The REC (Recording Timer) indicator stops flashing
and remains lit. The settings you have done are shown
on the display in sequence.

On the unit ONLY:

1 Put a recordable cassette into deck B.
2 Press CLOCK/TIMER repeatedly
until “REC” appears on the
display.

7 Press STANDBY/ON

to
turn off the unit (on standby)
if necessary.

The REC (Recording Timer) indicator also
starts flashing on the display.

STANDBY/ON
STANDBY

If you want to listen to another source while recording
Press REC START/STOP or 7 to stop recording. Without stopping
it, you cannot change the source.

• Each time you press the button, the timer setting modes
change as follows:
DAILY
Canceled

ON TIME
Clock
setting

REC
ON TIME

Even if you unplug the AC power cord or if a power
failure occurs
Once you set the timer, the timer setting may remain stored in
memory in a few days. In this case, check whether the timer setting
still remains or not.

(See page 9.)

3 Press CLOCK/TIMER again.
“ON TIME” appears for 2 seconds, then the
unit enters on-time setting mode.

– 23 –
EN18-26.MX-G90&80&70[J]f

12/20/00, 11:05 PM

To turn on or off Recording Timer after its setting is
done

Timer Priority

1 Press CLOCK/TIMER repeatedly until
“REC” appears on the display.

Since each timer can be set separately, you may wonder what
happens if the setting for these timers overlaps.
Here are examples.

2 To turn off the Recording Timer, press
CANCEL/DEMO.
The REC (Recording Timer) indicator goes
off from the display.
The Recording Timer is canceled, but the
setting for the Recording Timer remains in
memory.
To turn on the Recording Timer, press
SET/DISPLAY.
The REC (Recording Timer) indicator lights
up on the display. The settings you have done
are shown on the display in sequence for your
confirmation.

Recording Timer has priority over Daily Timer and Sleep
Timer.
• If Daily Timer is set to come on while Recording Timer is
operating, Daily Timer will not come on at all.
AM 6:00

does not work.

• If Recording Timer is set to come on while Sleep Timer is
operating, Sleep Timer will not work (the SLEEP indicator
does not go off).
9:30

10:00

10:30

Recording Timer
Sleep Timer

With Sleep Timer, you can fall asleep to music.
You can set Sleep Timer only while the unit is turned on.

does not work.

How Sleep Timer actually works
The unit automatically turns off after the specified time
length passes.

On the remote control ONLY:

1 Press SLEEP.
The time length until the shut-off time
appears and the SLEEP indicator starts
flashing on the display.
• Each time you press the button, the time length changes
as follows:
SLEEP20

SLEEP30

SLEEP120

SLEEP60

SLEEP90

2 Wait for about 5 seconds after specifying the
time length.
The SLEEP indicator stops flashing and remains lit.
To check the remaining time until the shut-off time, press
SLEEP once so that the remaining time until the shut-off time
appears for about 5 seconds.
To change the shut-off time, press SLEEP repeatedly until
the desired time length appears on the display.
To cancel the setting, press SLEEP repeatedly unitil the
SLEEP indicator goes off.
• Sleep Timer is also canceled when you turn off the unit.

– 24 –
EN18-26.MX-G90&80&70[J]f

7:30

Daily Timer

Using Sleep Timer

Canceled

7:00

Recording Timer

PM 9:00

SLEEP10

6:30

12/20/00, 11:05 PM

Maintenance
To get the best performance of the unit, keep your discs, tapes, and mechanism clean.

Handling discs

Handling cassette tapes
• Remove the disc from its case by
holding it at the edge while pressing the
center hole lightly.
• Do not touch the shiny surface of the
disc, or bend the disc.
• Put the disc back in its case after use to
prevent warping.

• If the tape is loose in its cassette, take
up the slack by inserting a pencil in
one of the reels and rotating.
• If the tape is loose, it may get
stretched, cut, or caught in the
cassette.

• Be careful not to touch the tape
surface.

• Be careful not to scratch the surface of
the disc when placing it back in its
case.
• Avoid exposure to direct sunlight,
temperature extremes, and moisture.

• Avoid the following places to store the
tape:
— In dusty places
— In direct sunlight or heat
— In moist areas
— Near a magnet

To clean the disc
Wipe the disc with a soft cloth in a
straight line from center to edge.

Cleaning the unit
DO NOT use any solvent — such as conventional
record cleaner, spray, thinner, or benzine — to
clean the disc.

• Stains on the unit
Should be wiped off with a soft cloth. If the unit is
heavily stained, wipe it with a cloth soaked in water
diluted neutral detergent and wrung well, then wipe clean
with a dry cloth.
• Since the unit may deteriorate in quality, become
damaged or get its paint peeled off, be careful about
the followings.
— DO NOT wipe it with a hard cloth.
— DO NOT wipe it strong.
— DO NOT wipe it with thinner or benzine.
— DO NOT apply any volatile substance such as
insecticides to it.
— DO NOT allow any rubber or plastic to remain in
contact with it for a long time.

– 25 –
EN18-26.MX-G90&80&70[J]f

12/20/00, 11:05 PM

Troubleshooting
If you are having a problem with your unit, check this list for a possible solution before calling for service.
If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified person,
such as your dealer, for service.
Symptom

Cause

Action

Unable to cancel the display demonstration.

Other buttons will pressed to cancel the
display demonstration.

Press CANCEL/DEMO on the unit. (See
page 8.)

No sound is heard.

Connections are incorrect or loose.

Check all connections and make
corrections. (See pages 6 to 8.)

Hard to listen to broadcasts because of
noise.

• Antennas are disconnected.
• The AM loop antenna is too close to the
unit.
• The FM antenna is not properly extended
and positioned.

• Reconnect the antennas correctly and
securely.
• Change the position and direction of the
AM loop antenna.
• Extend the FM antenna at the best
position.

The disc sound is discontinuous.

The disc is scratched or dirty.

Clean or replace the disc. (See above.)

The disc tray does not open or close.

• The AC power cord is not plugged in.
• Trays are locked.

• Plug the AC power cord.
• Unlock the trays. (See page 16.)

The disc does not play.

The disc is placed upside down.

Place the disc with the label side up.

The cassette holders cannot be opened.

Power supply from the AC power cord has
been cut off while the tape was running.

Turn on the unit.

Impossible to record.

Small tabs on the back of the cassette are
removed.

Cover the holes with adhesive tape.

Operations are disabled.

The built-in microprocessor may
malfunction due to external electrical
interference.

Unplug the AC power cord and then plug it
back in.

Unable to operate the unit from the remote
control.

• The path between the remote control and
the remote sensor on the unit is blocked.
• The batteries are exhausted.

• Remove the obstruction.
• Replace the batteries.

– 26 –
EN18-26.MX-G90&80&70[J]f

12/20/00, 11:05 PM

Specifications

Design and specifications are subject to change without notice.

MX-GT90

MX-GT80

Amplifier section — CA-MXGT90

Amplifier section — CA-MXGT80

Output Power
SUBWOOFERS:

160 W per channel, min. RMS, driven into
6 Ω at 63 Hz with no more than 10% total
harmonic distortion.
MAIN SPEAKERS: 70 W per channel, min. RMS, driven into
6 Ω at 1 kHz with no more than 10% total
harmonic distortion.
Audio input sensitivity/Impedance
(at 1 kHz, measured at tape recording signal 300 mV)
AUX:
390 mV/50 kΩ
Digital output: CD OPTICAL DIGITAL OUTPUT
Signal wave length:
660 nm
Output level:
–15 dBm to –12 dBm
Speakers/Impedance:
SUBWOOFERS:
6 Ω – 16 Ω
MAIN SPEAKERS: 6 Ω – 16 Ω

Tuner
FM tuning range:
AM tuning range:

Tuner
87.5 MHz – 108.0 MHz
530 kHz – 1 710 kHz

CD player
CD capacity:
Dynamic range:
Signal-to-noise ratio:
Wow and flutter:

130 W per channel, min. RMS, driven into
6 Ω at 63 Hz with no more than 10% total
harmonic distortion.
MAIN SPEAKERS: 55 W per channel, min. RMS, driven into
6 Ω at 1 kHz with no more than 10% total
harmonic distortion.
Audio input sensitivity/Impedance
(at 1 kHz, measured at tape recording signal 300 mV)
AUX:
390 mV/50 kΩ
Digital output: CD OPTICAL DIGITAL OUTPUT
Signal wave length:
660 nm
Output level:
–15 dBm to –12 dBm
Speakers/Impedance:
SUBWOOFERS:
6 Ω – 16 Ω
MAIN SPEAKERS: 6 Ω – 16 Ω
FM tuning range:
AM tuning range:

87.5 MHz – 108.0 MHz
530 kHz – 1 710 kHz

CD player
3 CDs
85 dB
90 dB
Immeasurable

CD capacity:
Dynamic range:
Signal-to-noise ratio:
Wow and flutter:

3 CDs
85 dB
90 dB
Immeasurable

Cassette deck

Frequency response
Normal (type I): 50 Hz – 14 000 Hz
Wow and flutter
0.15% (WRMS)

General

Power requirement:
Power consumption:

AC 120 V
, 60 Hz
175 W/220 VA (at operation)
22 W (on standby)
Dimensions (approx.): 265 mm x 335 mm x 401 mm (W/H/D)
(10 7/16 in. x 13 1/4 in. x 15 13/16 in.)
Mass (approx.):
10.0 kg (22.1 lbs)

Power requirement:
Power consumption:

Supplied accessories

See page 6.

Speaker section — SP-MXGT90

Speaker section — SP-MXGT80

Type:

3-Way 3-Speaker Bass-Reflex Type
Dual Giga-Tube Band-Pass Subwoofers
Speaker units:
Subwoofer:
20 cm (7 7/8 in.) cone x1
Woofer:
10 cm (3 15/16 in.) cone x1
Tweeter:
5 cm (2 in.) dome x1
Power handling capacity:
Subwoofer:
160 W
Main speaker: 70 W
Impedance:
Subwoofer:
6Ω
Main speaker: 6 Ω
Frequency range:
Subwoofer:
25 Hz – 250 Hz
Main speaker: 75 Hz – 32 000 Hz
Sound pressure level: Subwoofer:
77 dB/W•m
Main speaker: 84 dB/W•m
Dimensions (approx.): 255 mm x 449 mm x 389 mm (W/H/D)
(10 1/16 in. x 17 11/16 in. x 15 3/8 in.)
Mass (approx.):
8.5 kg (18.8 lbs) each

AC 120 V
, 60 Hz
165 W/210 VA (at operation)
20 W (on standby)
Dimensions (approx.): 265 mm x 335 mm x 401 mm (W/H/D)
(10 7/16 in. x 13 1/4 in. x 15 13/16 in.)
Mass (approx.):
10.0 kg (22.1 lbs)

3-Way 3-Speaker Bass-Reflex Type
Dual Giga-Tube Band-Pass Subwoofers
Speaker units:
Subwoofer:
16 cm (6 5/16 in.) cone x1
Woofer:
10 cm (3 15/16 in.) cone x1
Tweeter:
5 cm (2 in.) dome x1
Power handling capacity:
Subwoofer:
130 W
Main speaker: 55 W
Impedance:
Subwoofer:
6Ω
Main speaker: 6 Ω
Frequency range:
Subwoofer:
30 Hz – 120 Hz
Main speaker: 75 Hz – 29 000 Hz
Sound pressure level: Subwoofer:
78 dB/W•m
Main speaker: 85 dB/W•m
Dimensions (approx.): 230 mm x 439 mm x 340 mm (W/H/D)
(9 1/16 in. x 17 5/16 in. x 13 7/16 in.)
Mass (approx.):
7.2 kg (15.9 lbs) each

– 27 –
EN18-26.MX-G90&80&70[J]f

12/20/00, 11:05 PM

MX-G70
Amplifier section — CA-MXG70
Output Power
SUBWOOFERS:

110 W per channel, min. RMS, driven into
6 Ω at 63 Hz with no more than 10% total
harmonic distortion.
MAIN SPEAKERS: 55 W per channel, min. RMS, driven into
6 Ω at 1 kHz with no more than 10% total
harmonic distortion.
Audio input sensitivity/Impedance
(at 1 kHz, measured at tape recording signal 300 mV)
AUX:
390 mV/50 kΩ
Digital output: CD OPTICAL DIGITAL OUTPUT
Signal wave length:
660 nm
Output level:
–15 dBm to –12 dBm
Speakers/Impedance:
SUBWOOFERS:
6 Ω – 16 Ω
MAIN SPEAKERS: 6 Ω – 16 Ω

Tuner
FM tuning range:
AM tuning range:

87.5 MHz – 108.0 MHz
530 kHz – 1 710 kHz

CD player
CD capacity:
Dynamic range:
Signal-to-noise ratio:
Wow and flutter:

3 CDs
85 dB
90 dB
Immeasurable

Cassette deck
Frequency response
Normal (type I): 50 Hz – 14 000 Hz
Wow and flutter
0.15% (WRMS)

General
Power requirement:
Power consumption:

AC 120 V
, 60 Hz
160 W/205 VA (at operation)
20 W (on standby)
Dimensions (approx.): 265 mm x 335 mm x 401 mm (W/H/D)
(10 7/16 in. x 13 1/4 in. x 15 13/16 in.)
Mass (approx.):
10.0 kg (22.1 lbs)

Supplied accessories
See page 6.

Speaker section — SP-MXG70
Type:

3-Way 3-Speaker Bass-Reflex type
Twin Hyper Power-Drive Subwoofer
Speaker units:
Subwoofer:
14 cm (5 9/16 in.) cone x1
Woofer:
16 cm (6 5/16 in.) cone x1
Tweeter:
5 cm (2 in.) dome x1
Power handling capacity:
Subwoofer:
110 W
Main speaker: 55 W
Impedance:
Subwoofer:
6Ω
Main speaker: 6 Ω
Frequency range:
Subwoofer:
29 Hz – 310 Hz
Main speaker: 70 Hz – 29 000 Hz
Sound pressure level: Subwoofer:
76 dB/W•m
Main speaker: 87 dB/W•m
Dimensions (approx.): 286 mm x 335 mm x 365 mm (W/H/D)
(11 5/16 in. x 13 1/4 in. x 14 3/8 in.)
Mass (approx.):
6.3 kg (13.9 lbs) each

– 28 –
EN18-26.MX-G90&80&70[J]f

12/20/00, 11:05 PM

QUALITY

SERVICE

HOW TO LOCATE YOUR JVC SERVICE CENTER
TOLL FREE : 1-800-537-5722
http://www.jvcservice.com
Dear customer:
In order to receive the most satisfaction from your purchase, read the instruction booklet before operating the unit. In the event that repair
is necessary, or for the address nearest your location, please refer to the factory service center list below or within the Continental
United States, Call 1-800-537-5722 for your authorized servicer. Remember to retain your Bill of Sale for Warranty Service.
—JVC

JVC SERVICE & ENGINEERING
COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
FACTORY SERVICE CENTER LOCATIONS
10 New Maple Avenue
Pine Brook, NJ 07058-9641
(973) 396-1000

1500 Lakes Parkway
Lawrenceville, GA 30243-5857
(770) 339-2582

705 Enterprise Street
Aurora, IL 60504-8149
(630) 851-7855

5665 Corporate Avenue
Cypress, CA 90630-0024
(714) 229-8011

2969 Mapunapuna Place
Honolulu, HI 96819-2040
(808) 833-5828

10700 Hammerly, Suite 110
Houston, TX 77043
(713) 935-9331

13 Cummings Park
Woburn, MA 01801
(781) 376-9100

8192 State Road 84
Davie, FL 33324
(954) 472-1960

890 Dubuque Avenue
South San Francisco, CA 94080-1804
(650) 871-2666

Sophisticated electronic products may require occasional service. Just as quality is a keyword in the engineering and production of
the wide array of JVC products, service is the key to maintaining the high level of performance for which JVC is world famous. The
JVC service and engineering organization stands behind our products.
NATIONAL HEADQUARTERS
JVC SERVICE & ENGINEERING COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
1700 Valley Road
Wayne, NJ 07470

If you ship the product • • •
Pack your JVC unit in the original carton or one of equivalent
size and strength. Enclose, with the unit, a letter stating the
problem or symptom that exists and also a copy of the
receipt or bill of sale you received when you purchased your
JVC unit. Print your home return address on the outside
and the inside of the carton. Send to the appropriate JVC
Factory Service Center as listed above.

Don’t service it yourself.
CAUTION
To prevent electrical shock, do not open the cabinet. No user
serviceable parts inside.
Refer servicing to qualified service personnel.

ACCESSORIES
To purchase accessories for your JVC product, you may contact your local JVC Dealer.
Or from the 48 Continental United States call toll free : 800-882-2345

(1099)

MX-GT90&80&70[J]Warranty

12/20/00, 11:02 PM

LIMITED WARRANTY

AUDIO-1

JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL
PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIAL AND WORKMANSHIP from the date of original retail
purchase for the period as shown below. (“The Warranty Period.”)
PARTS

LABOR
1YR

1YR

THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY(50) UNITED STATES, THE DISTRICT OF COLUMBIA AND IN
COMMONWEALTH OF PUERTO RICO.
WHAT WE WILL DO:
If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such
repair and replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers.
Parts used for replacement are warranted only for the remainder of the Warranty Period. All products and parts thereof may be
brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and
above which are covered on an in-home basis.
WHAT YOU MUST DO FOR WARRANTY SERVICE:
Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized
service center, please call toll free: (800)537-5722.
If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of
your bill of sale plus and letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location
of which will be given to you by the toll-free number.
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.
WHAT IS NOT COVERED:
This limited warranty provided by JVC does not cover:
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty
installation, lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC to
render such service, or if affixed to any attachment not provided with the products, or if the model number or serial number
has been altered, tampered with, defaced or removed;
2. Initial installation and installation and removal for repair;
3. Operational adjustments covered in the Owner’s Manual, normal maintenance, video and audio head cleaning;
4. Damage that occurs in shipment, due to act of God, and cosmetic damage;
5. Signal reception problems and failures due to line power surge;
6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus(Needle) are covered for 90 days from the date of purchase;
7. Accessories;
8. Batteries (except the Rechargeable Batteries are covered for 90 days from the date of purchase);
There are no express warranties except as listed above.
THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY, IS
LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER
DAMAGES, WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TO
TAPES, RECORDS OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF
THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied
warranty last, so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you
may also have other rights which vary from state to state.
JVC COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.

1700 Valley Road
Wayne, NJ 07470

REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY DOES NOT APPLY. FOR DETAILS OF
REFURBISHED PRO DUCT WARRANTY, PLEASE REFER TO THE REFURBISHED PRODUCT WARRANTY INFORMATION
PACKAGED WITH EACH REFURBISHED PRODUCT.
For customer use:
Enter below the Model No. and Serial No. which is located either on the rear, bottom or side of the cabinet. Retain this
information for future reference.

MX-GT90&80&70[J]Warranty

Model No.:

Serial No.:

Purchase date:

Name of dealer:

12/20/00, 11:02 PM

VICTOR COMPANY OF JAPAN, LIMITED

MX-GT90&80&70[J]Coverf

0101MWMMDWJEM

12/20/00, 11:03 PM

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2000:12:20 23:11:27
Producer                        : Acrobat Distiller 3.01 for Power Macintosh
Author                          : CC_YEOH
Creator                         : PageMaker 6.0
Title                           : MX-GT90&80&70[J]Coverf
Modify Date                     : 2001:03:15 11:32:30+09:00
Page Count                      : 34
Page Mode                       : UseOutlines
Page Layout                     : SinglePage

EXIF Metadata provided by EXIF.tools

Jvc Mx Gt90 Users Manual GT90&80&70[J]Coverf

If not then 20920ien Manual: ://resources.jvc.com/Resources/00/00/98/20920ien

Navigation menu

Versions of this User Manual:

Views

Navigation