KAB Enterprise TR-015-2 Remote Controller User Manual RC 018 TR 015 1
Kab Enterprise Co., Ltd. Remote Controller RC 018 TR 015 1
user manual
RC-018 + TR-15-2 Indoor Wireless Remote Control IMPORTANT SAFEGUARDS NOTE: These are general definitions only; all may not pertain to the actual product purchased. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Usage of this signal word is limited to the most extreme situations. WARNING: Indicates potentially hazardous situation, which, if not avoided, may result in minor / moderate injury or product/ property damage. It also alerts against unsafe practices. When using electrical products, always follow basic safety precautions including the following: Clear Lights Cle Clear ar Multi Mu lti Multi Lights All Lights Off ELECTRICAL RATINGS Voltage Frequency Electronic Ballast 125VAC 60Hz 500VA Tungsten 1000W Amperage Horse Power Ballast 1/2HP 120Vac 60Hz 8.3Ballast 15A RECEIVER MODEL #RC-018 TRANSMITTER MODEL #TR-015-2 FCC ID: PAGTR-015-2 WARNING-- To reduce the risk of fire, electric shock, or serious personal injury • Do not immerse the product in liquids • This product is not intended for use by children and contains small parts that may pose a choking hazard to children under the age of three. Keep the product out of the reach of children and pets. • Do not use an electrical device or appliance with this product whose electrical specifications exceed those specified in the “Electrical Specifications” section of this manual. CAUTION-- To reduce the risk of personal injury or product/ property damage: • This product is intended for non-commercial, non-industrial use in the remote control of two electrical outlets. Do not use this product for any other purpose. TO USE 1. To set up the receiver (outlet) with connecting device. 2. Removes the plastic battery tab from the battery compartment in the back of the remote control to active the DC 12V Type A23 pre-installed battery. 3. Press “Clear Lights” button on the transmitter to turn the “Clear” receiver ON and press Off button on the transmitter to turn the receiver OFF. 4. Press “Multi Lights” button on the transmitter to turn the “Multi” receiver ON and press OFF button on the transmitter to turn the receiver OFF. 5. Press “All Lights” button on the transmitter to turn the “Clear” and “Multi” receivers ON and press OFF button on the transmitter to turn the receivers OFF. Battery Handling and Usage WARNING: Keep batteries away from children and pets. • Follow the battery manufacturer’s safety and usage instructions. • Insert the battery observing the proper polarity (+/-) as indicated inside the Battery Compartment. SET UP 1. 2. 3. Plug receiver into a standard 125-volt AC electrical outlet. Confirm that the electrical specifications of an item you wish to use with this product do not exceed those specified in the “Electrical Ratings” section. plug the item into an outlet of the receiver. Remove the plastic battery tab from the battery compartment in the back of the remote control to activate the DC 12V Type A23 pre-installed battery. CAUTION: Failure to properly align the battery polarity can cause personal injury • • • and/or property damage. Remote a spent or discharged battery from the product. remove the battery when not using the product for an extended period. Never throw batteries into a fire. Do not expose batteries to fire or other heat sources. Battery contains mercury. Do not put in trash. Recycle or manage as hazardous waste. Battery Replacement • • • Remove the Battery compartment cover from the back of the remote control by sliding the cover in the direction that its trends curve. Remove the spent battery and place a new DC 12V Type A23 battery into the Battery Compartment correctly observing the polarity indications (+/-) inside the Battery Compartment. Replace the Battery Compartment Cover. Federal Communications Commission Interference Statement This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help." This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Made in China
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Format : application/pdf Creator : ¹ù¼ª¾ü Title : RC-018_TR-015-1 Create Date : 2013:05:08 14:51:41+08:00 Creator Tool : Adobe Illustrator CS6 (Macintosh) Modify Date : 2013:05:08 14:51:41+08:00 Metadata Date : 2013:05:08 14:51:41+08:00 Thumbnail Width : 256 Thumbnail Height : 112 Thumbnail Format : JPEG Thumbnail Image : (Binary data 13355 bytes, use -b option to extract) Producer : Adobe PDF library 10.01 Document ID : xmp.did:0880117407206811822A9EC3CCB847B7 Instance ID : uuid:c883e241-7f27-b048-8a6d-33d1d73d0b54 Original Document ID : uuid:c4e930fb-4f14-4c4c-b1b7-13d127f3e4e8 Rendition Class : proof:pdf Derived From Instance ID : uuid:75f4c0c1-9acd-d944-922c-8b1362123489 Derived From Document ID : xmp.did:13A2B2D455206811822AE68984523DFB Derived From Original Document ID: uuid:c4e930fb-4f14-4c4c-b1b7-13d127f3e4e8 Derived From Rendition Class : proof:pdf History Action : saved, saved History Instance ID : xmp.iid:0380117407206811822AE68984523DFB, xmp.iid:0880117407206811822A9EC3CCB847B7 History When : 2013:05:07 11:44:53+08:00, 2013:05:08 14:51:38+08:00 History Software Agent : Adobe Illustrator CS6 (Macintosh), Adobe Illustrator CS6 (Macintosh) History Changed : /, / N Pages : 1 Has Visible Transparency : False Has Visible Overprint : False Max Page Size W : 297.038889 Max Page Size H : 204.627648 Max Page Size Unit : Millimeters Font Name : Arial-Bold, ArialMT, ArialMT-Italic, ArialMT-Medium, ArialMT-Bold, AdobeMingStd-Light, TrebuchetMS, TrebuchetMS-Bold Font Family : Arial, Arial, Arial MT, Arial MT, Arial MT, Adobe 明體 Std, Trebuchet MS, Trebuchet MS Font Face : Bold, Regular, Italic, Medium, Bold, L, Regular, Bold Font Type : Type 1, Open Type, Type 1, Type 1, Type 1, Open Type, TrueType, Open Type Font Version : 001.000, Version 5.01.2x, 001.003, 001.003, 001.003, Version 6.007;PS 6.001;hotconv 1.0.67;makeotf.lib2.5.33168, Version 1.00, Version 5.00x Font Composite : False, False, False, False, False, False, False, False Font File Name : ArialBol; Arial Black, Arial.ttf, ArialMTIta; ArialMT.suit, ArialMTMed; ArialMT.suit, ArialMTBol; ArialMT.suit, AdobeMingStd-Light.otf, Trebuchet MS, Trebuchet MS Bold.ttf Plate Names : Cyan, Magenta, Yellow, Black Swatch Groups Group Name : Default Swatch Group Swatch Groups Group Type : 0 Page Count : 2 Author : ¹ù¼ª¾üEXIF Metadata provided by EXIF.tools