KAB Enterprise TR-016 Remote Controller User Manual MODEL RC 001 OUTDOOR REMOTE CONTROLLER

Kab Enterprise Co., Ltd. Remote Controller MODEL RC 001 OUTDOOR REMOTE CONTROLLER

user manual

RC-018 + TR-016 Indoor Wireless Remote Control SET UP 1. Plug the receiver into a standard 125-volt AC electrical outlet. 2. Confirm that the electrical specifications of an item you wish to use with this product do not exceed those specified in the "Electrical Ratings" section. Plug the item into an outlet of the receiver.
3. Remove the plastic battery tab from the battery compartment in the back of the remote control to activate the DC 12V Type A23 pre-installed battery. ELECTRICAL RATINGS Range Up to 50ft. 125Vac 60Hz 15 A General Purpose 125Vac 60Hz 15 A Resistive 1,000 W Tungsten 500 VA Electronic Ballast 120Vac 60Hz 8.3A Ballast. 1/2 HP TO USE 1. To set up the receiver (outlet) with connecting device. 2. Removes the plastic battery tab from the battery compartment in the back of the remote control to active the DC 12V Type A23 pre-installed battery. 3. Press "Clear" ON button on the transmitter to turn the "Clear" receiver ON and press OFF button on the transmitter to turn the receiver OFF. 4. Press "Multi" ON button on the transmitter to turn the "Multi" receiver ON and press OFF button on the transmitter to turn the receiver OFF. 5. Press "Both" ON button on the transmitter to turn the "Clear" and "Multi" receiver ON and press OFF button on the transmitter to turn the receiver OFF. Battery Handling and Usage WARNING: Keep batteries away from children and pets. • Follow the battery manufacturer's safety and usage instructions. • Insert the battery observing the proper polarity (+/-) as indicated inside the Battery Compartment. CAUTION: Failure to properly align the battery polarity can cause personal injury and/or property damage.
• Remove a spent or discharged battery from the product. Remove the battery when not using the product for an extended period. • Never throw batteries into a fire. Do not expose batteries to fire or other heat sources. • Battery contains mercury. Do not put in trash. Recycle or manage as hazardous waste. Battery Replacement • Remove the Battery compartment cover from the back of the remote control by sliding the cover in the direction that its treads curve. • Remove the spent battery and place a new DC 12V Type 23A battery into the battery compartment, correctly observing the polarity indications (+/−) inside the battery compartment. • Replace the battery compartment cover. Federal Communication Commission Interference Statement • This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : • Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. • FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. • This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. • This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. Made In China

Navigation menu