KC Wirefree BTMODULE-CL2 Bluetooth Module User Manual Exhibit D Users Manual per 2 1033 b3
KC Wirefree Corporation Bluetooth Module Exhibit D Users Manual per 2 1033 b3
Exhibit D Users Manual per 2 1033 b3
Bluetooth Wireless Engineering & Design
Phone (623) 581-0700
Fax (623) 581-9192
KC Wirefree • 11811 North Tatum Boulevard • Suite 3031 • Phoenix, Arizona 85028
Rev: 1.0 4/10/2005
KC21 Bluetooth Module OEM General User and
Installation Guide
I. OEM Usage Intructions
Installation
The KC-21 is a Class-2 Bluetooth Module supplied on a 24 pin surface mount, 6-
layer PCB, 26.9mm x 15.2mm footprint. For non Pb-free applications, Sn63Pb37
solder is recommended. The maximum reflow temperature must be below 220C.
Layout
The area around the KC21 module should be free of any ground planes, trace
routings, or metal for at least 250 mil (6.4 mm) from the antenna in all directions.
Traces should not be routed underneath the module.
Crystal Tuning and Power Calibration
These steps are performed by KC Wirefree, and must NOT be modified from the
settings applied during manufacturing. Any changes to these settings may void the
user’s authority to operate this equipment.
Operating Conditions
The permitted operating and storage temperatures, power supply requirements, and
I/O tolerances are specified in the KC21 Datasheet.
II. Notice of FCC Regulatory Compliance
This module has been tested and found to comply with the FCC Part15 Rules.
These limits are designed to provide reasonable protection against harmful
interference in approved installations. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. This
device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
Modifications or changes to this equipment not expressly approved by KC Wirefree
may void the user’s authority to operate this equipment.
Bluetooth Wireless Engineering & Design
Phone (623) 581-0700
Fax (623) 581-9192
KC Wirefree • 11811 North Tatum Boulevard • Suite 3031 • Phoenix, Arizona 85028
Rev: 1.0 4/10/2005
III. Limited Modular Approval
FCC ID: S22BTMODULE-CL2
In accordance with FCC Part 15, the KC21 is listed above as a Limited Modular
Transmitter device.
In support of the Modular Transmitter Approval, the following is stated:
1. The module does have buffered modulation / data inputs.
2. The module does regulate its own power supply.
3. The module does have a permanently attached antenna.
4. The module can be tested as a stand-alone device.
5. The module is labeled with the proper FCC ID, and labeling instructions are
provided to OEM end users for external product labels.
6. The module does have instruction for proper use.
7. The module does meet the FCC RF regulations.
Limited Modular Transmitter Approval, is granted, instead of Modular Transmitter
Approval, because the following condition is not met:
8. The module does not have its own RF shielding.
In accordance with FCC document, DA 00-1407, all final usage by OEMs of this
device, (1) Must be approved by the module’s manufacturer, KC Wirefree, (2) final
installation must follow the instructions in this user’s manual, (3) a written agreement
with the OEM will detail which products are approved for this module’s final
installation to control its end usage and ensure FCC Part 15 compliance.
IV. FCC Label Instructions
The outside of final products that contain a KC21 device must display a label
referring to the enclosed module. This exterior label can use wording such as the
following: “Contains Transmitter Module FCC ID: S22BTMODULE-CL2” or “Contains
FCC ID: S22BTMODULE-CL2.” Any similar wording that expresses the same
meaning may be used. An example of this label is figure 1 below:
Bluetooth Wireless Engineering & Design
Phone (623) 581-0700
Fax (623) 581-9192
KC Wirefree • 11811 North Tatum Boulevard • Suite 3031 • Phoenix, Arizona 85028
Rev: 1.0 4/10/2005
Model: KC21
Contains Transmitter Module
FCC ID: S22BTMODULE-CL2
This product complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
Input: 3.3VDC 120MA
Made in China
KC Wirefree
Figure 1: External Device FCC Label Sample