KCodes KCODES-604 KC604X printer server User Manual
KCodes Corporation KC604X printer server Users Manual
KCodes >
Users Manual
KCodes 6 Series v2 USB 2.0 Device Server User’s Manual Chapter 1 Introduction Tha k ou fo pu hasi g 6 /6 /6 4/6 4 U“B De i e “e e i the follo i g efe ed to as “e e . This Server is designed to connect your Multifunction Printer, Scanner, Fax, Multifunction Printer, Hard Drive, iPhone, iPod, USB Digital TV Tuner, Digital Camera, USB Webcam, USB Speaker, USB CD, USB DVD to your et o k, allo i g all et o k use s’ a ess to these sha ed U“B de i es. 1.1 About 4 Models Described in this Manual This manual provides introductory information as well as detailed instructions on how to set up and manage 6 Series in various network environments. The following table shows the differences among the 4 models. All 4 models have a 10/100 Mbit/sec Lan port. However, 601 v2 and 601n v2 has only one USB port, while both 604 v2 and 604n v2 have four USB ports. Compared with 4 models have an additional wireless module (802.11b/g/n). Except for the wireless configuration, most configuration and operations are the same for 601 v2/604 v2 and 601n v2/604n v2. Similarly, almost all of the configuration and operations are the same for these models except that only one USB device can be connected to 601 v2/601n v2 while at most four USB devices can be connected to 604 v2/604n v2. Unless explicitly specified, all instructions in the manual apply to 6 Series. Model Na e 6 4 6 4 LAN Yes Yes Yes Yes Wi eless No No Yes Yes U“B Po t s To fully benefit from this document, you should be familiar with basic networking principles. The instructions described in this manual are based on the settings in a new Server. To reload the Factory Parameters, you can reset this Server back to Factory Default, which will restore most of the settings. For details, please efe to the hapte Resto e Fa to Defaults . 1.2 Customer Support Should you require any technical assistance, please contact your product reseller. Or you can visit our website for latest product information. This document is subject to changes without prior notice. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 Chapter 2 2.1 Product Overview Package Contents Verify that nothing is missing from the package by using the checking list below. Please contact your dealer if anything is missing or damaged. All packing materials are recyclable. Please confirm the items in the package below: This Server ( 601/601n/604/604n) CD (Control Center and User’s Manual and Quick Installation Guide) Power Adaptor 2.2 Product CD This CD provides easy-to-use Co t ol Ce te soft a e, a d the Use ’s Ma ual a d Qui k I stallatio Guide. 2.2.1. Start-up Procedures If your computer is configured to auto start CDs, this CD will start automatically when inserted. You can also navigate to the CD and start the autorun.exe file from within the Windows file manager. 2.3 Physical Description 1. 2. 3. 4. 5. 6. Power Adaptor Connector : 5V/1A (for 601 v2/601n v2) or 12V/2A (for 604 v2/604n v2) Init Button : for restoring the configurable parameters to the default values Wireless Station (only for 601n v2/604n v2) : IEEE 802.11 b/g/n wireless station with antenna Ethernet Connector : connected to a twisted pair category 5 cable USB Host Ports: USB 1.1/2.0 low, full, and Hi-Speed compliant Indicators For 6 Series Power Indicator is lit while power is applied. If it is not lit, or if it blinks, there is a problem with the USB device server or Power Adapter. USB Indicator (one for 601 v2/601n v2, four for 604 v2/604n v2) is lit while a USB device connects to a USB Port of the USB device server. If it is not lit, there is a problem with the USB device or the USB device server. For 601 v2/604 v2 Link Status is lit while network is applied. If it is not lit, it indicates that this server does not connect to the network. Status Indicator blinks to indicate network activity. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 For 601n v2/604n v2 2.4 LAN Indicator blinks to indicate wired network activity. If it is lit, it indicates the wired network is applied. If it is not lit, it indicates that the server does not connect to the wired network. WLAN Indicator blinks to indicate wireless network activity. If it is lit, it indicates the wireless network is applied. If it is not lit, it indicates that the server does not connect to the wireless network. Supported USB Devices The USB device server supports the following types of USB devices. USB Printer USB multifunction printer (MFP/AIO) USB scanner USB storage iPad iPhone © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 Chapter 3 Basic Installation 3.1. Connecting the Hardware 1. 2. 3. 4. 5. Make su e that ou U“B de i es a e s it hed off a d that the “e e ’s Po e Adapte is disconnected. Connect the USB devices to the USB ports with the USB cables. Connect the Server to the network with a twisted-pair category 5 cable, 10baseT or 100baseTX. Turn on the USB devices and make sure it is ready for use. Connect the Power Adapter to the Server. The power indicator will light up and USB1 and USB2 indicators will flash in turn. (For 601/601n, only USB1 indicator will flash.) When the Link indicator lights up, the Server is correctly connected to the network. When USB1 and USB2 indicators stop flashing, the Server starts to work normally. 3.2. Wireless connection This section only applies to 601n/604n. 3.3.1. Preliminary 3.3.2. 1. 2. Before you can access wireless network, wireless parameters should be set correctly. You have to setup the first wireless parameter set through LAN (wired) connection. Wireless access can be set as infrastructure (station) mode, which need an access point to route network messages with the same SSID. Wireless access can be secured by WEP (64/128), WPA-PSA (TKIP/AES), and WPA2-PSK (AES). If parameters mismatch causes wireless access is not allowed, you have to modify those parameters through LAN connection. In infrastructure mode, the maximal transfer rate is 150 MBits depending on access point’s capability. Set Wireless Configuration Using Control Center Install USB Device Server Control Center. It is available in the 601n v2/604n v2 USB Device Server Product CD. Start USB Device Server Control Center and Auto-searching USB device server window will appear. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 I f t he wireless param et er s are not correct or not set yet , y ou have t o use LAN t o access USB Device Server Cont rol Cent er. 3. If the tool finds USB device servers in your local area network, then you have to select a server from the server list. 4. Dou le li k the highlighted se e o li k the Co figu e “e e pages. Click CONFIG icon. utto to get the se e ’s e © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 5. Login with administrator ID (default: admin) and its password (default: admin). 6. Click Wireless icon. The e a e t o a s to o e t to i eless et o k. O e is “ a AP , the othe is Ma ual o e t . 8. B “ a AP , li k E te a d hoose the ““ID ou a t to o e t. Afte sele t, ou ha e to enter the password. 9. By Ma ual o e t, to join an existing wireless network, you have to set the correct SSID, and the correct security method with the correct key information. 10. If the wireless network is secured by WEP64 or WEP128, key index and WEP key must be set correctly. 7. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 11. If the wireless network is secured by WPA-PSK or WPA2-PSK, the key formats, shared key and encryption must be set correctly. 12. Click Submit to save your settings. And the server will reboot. 13. You have now finished the procedure of setting the wireless parameters After properly configuring the wireless parameters, you can remove the network cable and reboot the 601n/604n. 601n/604n will then connect to your wireless network. 601n/604n will detect if a network cable is plugged-in or not. If a network cable is plugged-in, 601n/604n will always connect to the © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 network through the network cable. Otherwise it will always connect to the network through wireless module. Once 601n v2/604n v2 connects to the network, either by network cable or by wireless module, all operations to use USB device server are exactly the same. 3.3. Assigning an IP Address to the Server 3.3.1. Preliminary 3.3.2. IP Address 3.3.3. If you have a DHCP server on your network, your Server will receive an IP address automatically. The IP address will then appear on the Control Center or on the page of configuration report that you printed earlier. If your DHCP server does not give an IP address to the Server, the Server will use the automatic private IP addressing IP: 169.254.0.0. ~ 169.254.255.255 If you are not working in a DHCP network, you need to manually set the Server’s IP address. Unless you are assigning an IP address using DHCP, you must obtain an unused IP address from your network administrator. Methods for Setting the IP Address You can set the IP address of your Server using one of the following methods, depending on your network operating environment: Automatic IP Address Assignment Manual IP Address Assignment 3.3.4. Server Names and Server Name Rules The default se e a e of the “e e is KC6 fo 6 o KC6 4 fo 6 4 o KC6 fo 6 KC6 4 fo 6 4 . If ou put t o o o e “e e s i ou lo al a ea et o k, to a oid usi g the sa e server names you have to change the server names by using the Control Center or the Serve ’s e pages. If your server name is longer than 15 characters, the Server uses only the first 15 characters. 3.3.5. Setting the IP Address Using DHCP Follow the instructions below to get an IP address using DHCP: © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 1. 2. 3.3.6. Edit or create a scope in the DHCP manager of the DHCP daemon. The entries included in this scope should contain the following parameters: range of IP addresses subnet mask default router IP address DNS server IP address lease duration Activate the scope. The Server automatically gets the DHCP parameters. If you are using DNS, you may include at least one DNS server IP address in the DHCP scope or manually set the DNS server IP add ess usi g “e e ’s e pages o the Co t ol Ce te . Setting the IP Address Using the Control Center 1. 2. Install the Control Center. The Control Center is available on the Product CD. Start the Control Center and Auto-searching Server window will appear. 3. If the tool finds multiple Servers in your local area network, then you have to select one Server from the Server List. 4. Dou le li k the highlighted se e o li k the Co figu e “e e utto to get the se e ’s e pages. Click CONFIG icon. Login with administrator ID (default: admin) and its password (default: admin). 5. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 6. 7. Click the button corresponding to your choice of IP setting methods (static or dynamic using DHCP). When assigning a static IP address you also have to define Subnet Mask. Click Submit to save your settings. And the Server will reboot. You have now finished the procedure of setting the IP address. Chapter 4 Using the USB Device Server 4.1. Introduction The goal of this produce is to provide the USB device server in a single product. We developed a new te h olog alled NetU“B to a hie e this goal. Basi all , the NetU“B is a U“B o e IP te h olog that t a spa e tl edi e ts all U“B pa kets to TCP/IP et o k ha el. NetU“B allo s ou to use U“B devices as if they were connected directly to your PC although they are actually remotely connected to the 601/601n/604/604n USB device server. 4.2. Connect & Disconnect NetU“B allo s ou to use U“B de i es as if the e e o e ted di e tl to ou PC although the a e a tuall e otel o e ted to the 6 /6 /6 4/6 4 U“B de i e se e . The o e t ope atio is a © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 software operation that simulates an actual USB device plug-i . That is to sa , he ou do a o e t ope atio i the Co t ol Ce te , PC a the dete t a U“B de i e’s plug-in, although actually you do not plug i a U“B de i e. “i ila l , the dis o e t ope atio is a soft a e ope atio that simulates the disconnection of the USB device. Once the connect operation is successful, the operations to use that USB device are just the same as if the USB device is directly connected to the PC. If a U“B de i e is o e ted a PC, e sa that PC has the ownership of the USB device. Only one PC can get the ownership of a USB device at the same time. Therefore, if a USB device is connected by one PC, no other PC can connect this USB device until this USB device is disconnected. 4.3. Subnet Issue Before using the NetUSB technology, you must first make sure that your PC can access USB device server ia TCP/IP. The si plest a to do this is usi g Co t ol Ce te to sea h fo the U“B de i e se e o the network and change its IP address to be the same subnet as your PC. If the server and your PC are not in the same TCP/IP subnet, Control Center will show the server in red, as the following figure. You must change the IP address (or using DHCP) of the server so that the server and your PC are in the same subnet. Control Center will show these servers in blue, meaning you can access these servers by the NetUSB technology. 4.4. Installation of USB Device Driver Some USB devices, like printers or MFPs (multifunction printers), require to install vendor-supplied driver (usually on CDROM). For those USB devices that do not need to install driver, please skip this section. 1. I se t the CDROM i to the CD d i e a d u the auto u p og a . 2. Follow the instructions of the installation program to install driver. 3. When the installation program asks you to plug-i the U“B de i e, u the Co t ol Ce te . 4. In the Control Center, click the USB device server that has the desired USB device attached. 5. Click the desired USB device as the following figure. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 6. Cli k the Co e t utto . The the be shown, as the following figure. essage Ma uall Co e t ou _ o pute _ a e 7. 8. Now, the installation program will detect the USB device and continue to install driver. After the installation is completed, click the USB device in the Control Center and then click the Dis o e t utto to dis o e t the U“B de i e. ill Now the driver of your USB device is installed. 4.5. Using the USB Device Server 1. 2. In the Control Center, click the USB device server that has the desired USB device attached. Click the desired USB device. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 3. Cli k the Co be shown. 4. Now, PC will detect the plug-i of the U“B de i e. The o e t ope atio is a soft a e ope atio that simulates an actual USB device plug-i . That is to sa , he ou do a o e t ope atio i the Co t ol Ce te , PC a the dete t a U“B de i e’s plug-in, although actually you do not plug in any USB device. Then, just use the USB device as if it is connected di e tl to ou PC’s U“B po t. After you finish using the USB device, click the USB device in the Control Center and then click the Dis o e t utto to dis o e t the U“B de i e. Othe PCs a ot Co e t the U“B de i e u til ou Dis o e t that U“B de i e. That is to sa , o l o e PC is allo ed to o e t the U“B device at the same time. 5. 6. e t utto . The the essage Ma uall Co e t ou _ o pute _ a e ill © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 4.6. Auto-Connect Printer The method described in section 4.5 is so-called manual-connect, which means users must manually connect the USB device before using that device, and must manually disconnect the USB device after using the device, otherwise nobody else can connect this device. However, for printers and scanners (and MFPs), the USB device server supports auto- o e t so use s do ’t eed to a uall o e t/dis o e t. This and the next sections show you how to do this. After the driver is installed as described in section 4.4, you can see a newly created printer in the Control Pa el’s P i te s a d Fa es . Follow the steps below to do a NetUSB auto-connect printing. 1. In the Control Center, click the USB device server that has the desired printer (or MFP) attached. 2. Click the desired printer (or MFP). 3. Cli k the Auto Co e t P i te utto a d hoose “et Auto-Co e t P i te . The following figure will appear. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 4. 5. Choose the desired printer. The desired printer must be the Windows printer (this is a logical printer) that matches the printer attached on the USB device server (this is a physical printer). The li k the Appl utto . The , the p i te ill e a ked as a Auto-Co e ted P i te i ed. If ou hoose AutoCo e ted P i te List i the Tools e u, ou a see a e l eated ite that des i es the association between the Windows printer and the physical printer on the server. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 6. 7. Then try to issue a print job to the desired printer. You will see the Control Center will automatically do a connect operation. Then, the print job will be issued to that printer. Even you already properly setup an auto-connected printer, the Control Center must be running i the a kg ou d hile a p i t jo is issued. This ea s ou’d ette u the Co t ol Ce te every time after you login Windows. In order to skip this manual operation, you can make the Control Center be run automatically after you login Windows. To do this, choose the Co figu atio ite i the Tools e u. The follo i g i do ill appea . Cli k o the he k o a d the o the OK utto . This featu e is e a led default. If you would like to break the association between the Windows printer and the physical printer, just click o the asso iatio a d li k the Delete utto i the Auto-Co e ted P i te List . © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 4.7. Network Scanner For NetUSB scanning, we recommend you use Network Scanner as the following steps. 1. 2. In the Control Center, click the USB device server that has the desired MFP (or scanner) attached. Click the desired MFP (or scanner). 3. Cli k the Net o k “ a e utto . The ou a see that the Co t ol Ce te do a o e t ope atio . The follo i g i do ill appea . 4. Choose o e of TWAIN o WIA ite . Cli k OK . The follo i g i do ill automatically ill appea . © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 5. 6. Follow the usual steps to do scanning. Afte the s a i g, lose the Auto-Co will automatically do a disconnect. e t“ a i do . At this o e t, Co t ol Ce te 4.8. USB Storage You ust use a uall o e t fo U“B sto age. Afte ou o e t a U“B sto age, like the follo i g picture, your PC ill ha e a e disk. If the U“B sto age is a flash d i e, the e disk is a e o a le disk . © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 You can see the storage icon in the system tray. Then just use the new disk as a general disk. After you finish the disk operations, click the storage icon in the s ste t a a d hoose “afel e o e U“B Mass “to age De i e to e o e the U“B sto age, as the following figure. The , i the Co t ol Ce te , li k the U“B sto age de i e a d li k the Dis o the USB storage device. e t utto to dis o e t 4.9. Request to Connect If a USB device is manually connected by any other user, basically you can not connect that device. Ho e e , e offe a othe e ha is alled Re uest to Co e t to sol e this i o e ie e. Fo example, there are two computers – TESTES a d TE“T. No the o e of HP Photos a t 6 is TE“T. Then, the TESTES computer wants to use this HP printer. The user on the TESTES computer can click the Re uest to Co e t utto i the Co t ol Ce te . The follo i g i do appea s. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 At this moment, the user on the TEST computer will see the following window, indicating that another computer – TESTES is requesting to use the HP printer. The user will choose to accept or reject. If accepted, the Control Center on TEST will automatically disconnect the device and the Control Center on TESTES will automatically connect that device. 4.10. Quitting the Control Center The Co t ol Ce te does ’t eall uit if ou li k the X o lose o at the top ight o e of the window. Instead, it just minimizes itself to the system tray. There are two ways to really close the Control Ce te . The fi st a is hoosi g E it ite i the File e u i the Co t ol Ce te . The se o d a is right-clicking the icon of the Control Center in the system tray and choosing the E it ite © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 4.11. Limitations There are some limitations to use the NetUSB technology. 1. 2. Only supports Windows XP/2003/Vista/7/8. Windows 98/ME is not supported. Only one PC can get the ownership of the same USB device at the same time. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 Chapter 5 File Server This chapter describes the file server function of the Server which allows USB storage devices to be shared across a network by using SMB: NetBIOS over TCP/IP and FTP protocol. 5.1. Preliminary 1. 2. 3. This product supports a file format of FAT32 a d NTF“. Ho e e , the ite ope atio o NTF“ is only supported in NetUSB mode. Please refer to the NetUSB Mode. Corporation is not responsible for the loss or corruption of data in memory devices, including hard disk; Corporation is not responsible for the leak, manipulation, loss, or corruption of data in memory devices connected to the Server after unauthorized access. In order to use the USB Mass Storage device connected to the Server, the SMB protocol or FTP protocol must be set up. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 5.2. Connecting USB Mass Storage to the Server LAN HUB/Switch The Server Storage 5.3. Supported Codepages What is codepage? Used by the system to encode and interpret string characters. Codepage formats are not the same for each language. Some languages, such as Japanese have multibyte characters, while others, such as English and German, need only one byte to represent each character. Filename Encoding of FAT File System This is known as an 8.3 file name, a short file name using codepage encoding. The FAT file system also supports file names that can be up to 255 characters long. This is known as a long file name using Unicode (UTF-16) encoding. When do you need to configure codepage? © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 The Server supports Windows codepages. If users want to communicate files using FTP client tool or SMB on Windows 98/Me/2000 with the Server, they have to set their Server codepage to be same as the codepage that their Windows PC is using. 1. 2. FTP SMB on Windows 98/Me/2000 Co figu i g the “e e ’s Codepages Users can use the following methods to set the “e e ’s odepage. 1. 2. 3. 4. 5. Start Control Center and Auto-searching Server window will appear. If the tool finds the Servers in your local area network, select the Server from the Server List and li k Co figu e “e e utton. The We a age ill sho , li k the Co fig utto a d e te the “e e ’s ad i ist ato (default: admin) and password (default: admin). After you have logged in successfully, setting General configuration dialog appears. Select your codepage form File Server Codepage box and click Apply. 5.4. Using Shared Storages by SMB/CIFS Method for Windows 1. 2. 3. 4. 5. 6. 7. 8. Connect a USB storage device to this product. Select My Network Places. Click Display the Computers of Workgroup. Double click Microsoft Windows Network icon. Double click the Workgroup that the Server belongs to. The default Workgroup name is WORKGROUP . You a efe to Co t ol Ce te o the “e e ’s e pages to get it. You ill see that the Server is displayed as its server name. If you cannot find Workgroup name of the Server in Microsoft Windows Network, you can select “ea h fo Co pute … i M Net o k Pla es a d e te the “e e Name of the Server to find it. Double click this Server Name icon. If you clear Enable SMB/CIFS Print/File Server Authentication in Supported Protocols, you login to the SMB server without requiring authentication; otherwise you have to enter user name and © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 password to login to the Server. You can add user name and password in User Account box by the Co t ol Ce te o the “e e ’s Web page. Note: If you use SMB on Windows 98 SE/ME, you must login to your Windows 98 SE/ME usi g the sa e use a e as i the “e e ’s Use A ou t. 9. The shared folders will be listed as USB1_DyPz, and USB2_DyPz where Dy represents the y-th disk and Pz represents the z-th partition with respect to USB1 port and USB2 port. 10. Perform Open, Paste, Remove or Copy the files to the shared folders. 5.5. Using Shared Storage by FTP Methods for Windows 1. 2. 3. 4. 5. 1. 2. 3. 4. Use Microsoft IE to the shared USB Mass Storages Open Microsoft IE In Web Address List, e te o a d: ftp://“e e ’s “e e Na e o ftp://“e e ’s IP add ess . If you have changed the default FTP port : 21 to the new value, you have to add the new port u e i the tail of o a d as ftp://“e e ’s “e e Na e: ftp po t o ftp://“e e ’s IP add ess: ftp po t . If you set Enable Server Authentication in FTP server protocol settings you have to enter user name and password to login to the Server; if you set Allow Anonymous Login, you can use the use a e a o ous to login with Read-only permission. If you clear Server authentication, you do not need username or password to login to the Server. You can add user name and pass o d i Use A ou t o the Co t ol Ce te o the “e e ’s We pages. The shared folders will be listed in IE. Perform Paste, Remove or Copy the files to the shared folders. Use Mi osoft Dos’s FTP lie t E te Dos o a d ftp . E te ope se e ’s “e e Na e o ope se e ’s IP add ess . If ou ha e ha ged the default FTP port : 21 to the new value, you have to add the new port number in the tail of command as ope se e ’s “e e Na e ftp po t o ope se e ’s IP add ess ftp po t . If you set Enable Server Authentication in FTP server protocol settings you have to enter user name and password to login to the Server; if you set Allow Anonymous Login, you can use the use a e a o ous to logi ith Read-only permission. If you clear Server authentication, you do not need username or password to login to the Server. You can add user name and password in User Account box the Control Ce te o the “e e ’s We pages. Perform FTP commands to use this FTP server. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 Chapter 6 The Server’s Web Pages 6.1. Introduction The Server runs the http server, httpd on TCP port: 80. Users may use the web pages to see the “e e ’s system status and configure the Server. 6.2. Using the Server’s Web Pages 6.2.1. Displaying Server Status Cli k o the “TATU“ i o to see s ste status, et o k status a d Wi eless “tatus (only for 601n/604n). © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 6.2.2. Setting up Server Configuration To set up the “e e o figu atio , li k o the CONFIG i o ad the the s ste enter administrator (default: admin) and password (default: admin) to login. ill e uest use to General Configuration Server Information: You have to set the Server Name, which is the name to represent the Server. TCP/IP: You have to set the Server’s TCP/IP configuration to connect TCP/IP network. Please see Chapter 3 Basic Installation for more details. Storage Access Mode: Set storage access mode as server or NetUSB mode. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 UPnP Setting: Enable or disable the UPnP function. File Server Codepage: Setup language for file server code. Administrator: You can change administrator name and password. If you forgot administrator name and password, you must perform Restore Factory Default action by plugging in the power adaptor while pressing the Init button. Please refer to the chapter “Restore Factory Defaults . Administrator: enter your desired administrator name. New Password: enter your desired password. Re-type Password: re-confirm the password. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 Maintenance If you want to restore factory default values of the Server or upgrade new firmware, you can use the Maintenance tool. Restart: click this button to restart (reboot) the Server. Factory Default: click this button, the Server will restore factory default values. Firmware Upgrade: click Browse to find the firmware file to be upgraded. Click Upload to upload the firmware into the Server. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 Chapter 7 Troubleshooting This chapter provides useful information to help you resolve difficulties that you may experience with your Server. Fault symptoms, possible causes, and remedial actions are provided within a quick reference table. This “e e ’s U“B po ts o l suppo t MFPs, p i te s, s a e s, ass sto age, a d U“B a e as. 7.1. LED Indicators 601 v2/604 v2 Indicators Power Behavior On Off Description Power On Power off/System error Link On Off Network connected No physical connection to network Status Blinking Activity on network USB Off On Off No activity on network USB device connected No physical connection to USB device Indicators Power Behavior On Off Description Power On Power off/System error WLAN Blinking Off Wireless Network connected (No LAN connected) No activity on Wireless Network LAN Blinking Activity on network USB Off On Off No activity on network USB device connected No physical connection to USB device 601n v2/604n v2 © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 7.2. Firewall If a firewall software has been installed on your PC, it may block the communication between the PC and the USB device server so that the USB device server can not work properly. To solve this problem, either disable the firewall or configure the firewall to allow the following TCP and UDP ports: 7303, 7305, 7411, 20005 © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 Chapter 8 You Restore Factory Defaults esto e the “e e ’s default pa a ete s o e of the follo i g ethods. 8.1. Using the Server’s Web Pages 1. 2. 3. 4. Go to the Serve ’s e page a d li k CONFIG Enter administrator (default: admin) and password (default: admin). Click Maintenance. Click Factory Default. 5. Click Yes to confirm 8.2. Using Init Button Turn on server and wait until you can see it on control center, press the initial button over 10 sec. Server will automatically shutdown and restart, this process will take about 1 and half min , after restart server will back to factory default. 8.3. Default Parameters List General Information Server Name: KC601 (for 601) or KC601n (for 601n) or KC604 (for 604) or KC604n (for 604n) TCP/IP Automatically get IP by DHCP: Enabled Static IP: Disabled - IP Address: 192.168.1.100 - Subnet Mask: 255.255.255.0 User Accounts Administrator: admin Password: admin © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 Chapter 9 Upgrade Firmware This chapter describes how to upgrade firmware. Please follow the following Procedures: 9.1 Using the Control Center 1. 2. 3. 4. 5. 6. Open Control Center. It will automatically search the existing Servers and display their statuses. Select the Server that you want to upgrade the firmware. Double click the selected Server to get the se e’s ai e page. Click CONFIG icon. Login the Server with Administrator (default: admin) and Password (default: admin). Click Maintenance. Click Upgrade Firmware. 7. 8. 9. Click Browse button to choose the file of new firmware. Click Upload button to start firmware upgrade. The server will reboot. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 Chapter 10 The Init Button The Init button is used for maintenance: Simultaneously press Init button and turn on (by plugging in the power adaptor) the Server will reboot. (For 601/601n, only USB LED indicator will blink.) After that, the Server will do the following tasks: Perform a Factory Default restoration of the server, which will restore most of the parameters and settings to factory default values. Note: After performing the tasks mentioned above, you have to plug off the power adaptor and then plug in the power adaptor to restart the Server. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0 FCC Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and it's antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. For MPE Statement – Mobile device IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. © 2014 KCodes Corporation. All rights reserved. 6 Series v2 User’s Manual V1.0
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Author : Amber;Cindy Create Date : 2015:06:25 10:58:25+08:00 Modify Date : 2015:06:25 16:00:24+08:00 Language : zh-TW Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Creator : Amber;Cindy Creator Tool : Microsoft® Word 2010 Metadata Date : 2015:06:25 16:00:24+08:00 Producer : Microsoft® Word 2010 Document ID : uuid:21af1401-f9a9-4d9f-8a15-0c63272700ee Instance ID : uuid:34b64e64-f9b6-4c47-92bd-95c52e84cd7f Page Count : 35EXIF Metadata provided by EXIF.tools