KIMIN Electronics PT50U7 PDP TV MONITOR User Manual User s Manual G

Kimin Electronic Co., Ltd PDP TV MONITOR User s Manual G

Users Manual

Order Number : GETEC-C1-09-146 FCC Class B Certification Test Report Number : GETEC-E3-09-080 Page 1 / 1 EUT Type: PDP TV/Monitor FCC ID.: TGEPT50U7 APPENDIX G : USER’S MANUAL
50”PDP TV USER’S GUIDEKPP-50SATPLEASE READ CAREFULLY BEFORE USEBefore Connecting, operating or adjusting this product, please read the instructions completely.Please keep this manual for future reference.For future reference, record the serial number of your PDP TV.SERIAL NO.The serial number is located on the rear of PDP TV.
Warning / Caution3TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN ORMOISTURE.WARNING/CAUTIONThis reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National ElectricCode (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable groundshall be connected to the grounding system of the building, as close to the point of the cable entry as practical.NOTE TO CABLE/TV INSTALLERDo not attempt to modify this product in any way without written authorization from the dealer.Unauthorized modification could void the user’s authority to operate this product.CAUTIONWARNING/CAUTIONTO REDUCE THE RISK OF ELECTRICSHOCK DO NOT REMOVE COVER (ORBACK). NO USER SERVICEABLE PARTSINSIDE. REFER TO QUALIFIED SERVICEPERSONNEL.The lightning flash with arrowheadsymbol, within an equilateral triangle,is intended to alert the user to thepresence of uninsulated “dangerousvoltage” within the product’s enclosurethat may be of sufficient magnitude toconstitute a risk of electric shock topersons.RISK OF ELECTRIC SHOCKDO NOT OPENThe exclamation point within an equi-lateral triangle is intended to alert theuser to the presence of importantoperating and maintenance (servicing)instructions in the literature accompa-nying the appliance.WARNING / CAUTION
Warning / Caution4WARNING / CAUTIONClass B digital deviceThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accor-dance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turn-ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the follow-ing measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.FCC NOTICEChanges or modification not expressly approved by the party responsible for compliance could void the user’sauthority to operate the equipment.Cautiona. The fluorescent lamp used in this product contains a small amount of mercury.b. Do not dispose of this product with general household waste.c. Disposal of this product must be carried out in accordance to the regulations of your local authority.On DisposalThe nationwide transition to digital television broadcasting by full-power TV stations will be completed by June 12,2009, but your local television stations may switch sooner. After the switch, analog-only television sets that receiveTV programming through an antenna will need a converter box to continue to receive over-the-air TV. Watch yourlocal stations to find out when they will turn off their analog signal and switch to digital-only broadcasting. Analog-only TVs should continue to work as before to receive low-power, Class A or translator television stations and withcable and satellite TV services, gaming consoles, VCRs, DVD players, and similar products.Information about the DTV transition is available from your local television stations, www.DTV.gov, or 1-888-CALL-FCC (TTY 1-888-TELL-FCC). Information about government coupons for eligible digital-to-analog converter boxesis available from www.dtv2009.gov or 1-888-DTV-2009 (TTY 1-877-530-2634).Digital Television Transition NoticeTo prevent fire or shock hazards, do not expose this product to rain or moisture.
Important Safety Instructions5Important Safety Instructions1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this apparatus near water.6. Clean only with dry cloth.7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (includingamplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades withone wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade orthe third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electri-cian for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, andthe point where they exit from the apparatus.11. Only use attachments/accessories specified by the manufacturer.12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damagedin any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen intothe apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has beendropped. 15. Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such asvases, are placed on the apparatus. 16. To completely disconnect this apparatus from the AC Mains, disconnect the mains plug from the AC receptacle.17. The mains plug of the power supply cord shall remain readily operable.18. This apparatus shall be connected to a Mains socket outlet with a protective earthing connection.
Important Safety Instructions6The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user tothe presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficientmagnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence ofimportant operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.Prolonged use of headphones at a high volume may cause health damage on your ears.NNNNOOOOTTTTEEEE
Contents7Contents3WARNING / CAUTION5Important Safety InstructionsWARNINGCAUTIONControlsAndConnectorsSetting upTVChannelPictureControlsInstallationConnectionBasicOperationOn ScreenMenus10 Front Panel11 Rear Panel12 Remote Control14 Wall mount Installation14 Desktop Pedestal Installation15 Antenna Connection16 VCR Connection18 DVD Connection20 HDSTB Connection22 External A/V Source22 Digital Audio Out23 USB in setup24 PC Connection25 Resolution26 Turning On or Off26 Channel Selection26 Volume Adjustment26 Sound Mute26 Quick View27 Input Selection27 Language Selection28 On Screen Menus29 Auto Scan30 Find Channel31 Add/Delete Channel32 EPG(Electronic Program Guide)33 Auto Picture Controls34 Manual Picture Controls35 Color Temperature36 Dynamic Contrast37 Noise Reduction38 Flesh Tone Correction39 Blue Stretch40 Film Mode41 Aspect Ratio42 Reset Picture Mode43 Auto Sound Controls44 Manual Sound Controls45 Speaker On/Off46 Auto Volume ControlSoundControls
Contents847 Digital Output48 Reset Audio Mode48 Stereo/SAP Broadcast SetupParentalControlSetting thePC ModeSpecialFunctionsSoundControlsTimeSetting49 Auto Time Setting50 Manual Time Setting51 Auto On/Off Time Setting52 Sleep TimerOptionMenus53 Audio Language54 Input Label55 Caption Mode56 Closed Caption-Analog57 Closed Caption-Digital58 Closed Caption Options60 Menu Opacity61 Enter your password61 Lock System62 Set Password63 Channel Blocking64 TV Ratings for USA65 TV (FCC) Age Categories66 Movie Ratings67 TV Rating English for Canada67 TV Rating French for Canada69 Downloadable Rating70 Auto Picture Controls71 Manual Picture Controls72 Watching PIP(Picture in Picture)73 Moving the sub picture74 PIP Audio Output75 Input Source Selection for sub picture (*Option)75 Swapping between Main and Sub pictures (*Option)75 Swapping between Main and Sub pictures audio75 Channel Selection for Sub Picture75 Sub Picture Size Adjustment (*Option)PhotosFunctions76 Before using the Photos Mode76 Screen Components77 Slide Show78 Setup the SlideshowMusicFunctions79 Before using the Music Mode79 Screen Components80 Listen to music81 Specification82 Troubleshooting83 CHILD SAFETY84 Warranty
Accessories9AccessoriesEnsure that the following accessories are included with your product.If an accessory is missing, please contact the dealer where you purchased the product.User must use shielded signal interface cables with ferrite cores to maintain standard compliance for the product.Supplied AccessoriesInstalling Batteries1Open the battery cover onthe back side.2Insert two batteries incorrect polarity, match (+ with +), and match(- with -).Don't mix old batterieswith new batteries.3Close the battery cover.1.5V1.5V123456789_0PRE.CHFAV.CHMUTEEPGSLEEPMENU EXITVOLCHINFO MTSRATIO CCPICTURESOUNDPHOTOMUSICPIPPIPINPUTSWAPPIPCH-AUD.SWAPSIZEPOSITIONPIPCH+SOURCEOKRemote & BatteriesPower cord Owner’s ManualAdaptor Plug(UL to VDE)
Controls And Connectors10Controls And ConnectorsFront Panel6SOURCEMENU+VOLCH123451. VOL + / VOL -Adjusts menu setting.Adjusts sound level.2. CH / CH Select a channel.3. SOURCESelects the TV, AV/S-Video, Component-1,Component-2, HDMI 1, HDMI 2, HDMI 3 or VGA mode.4. MENUDisplay on screen menus.5. POWERSwitches the set on or off.6. Power IndicatorIlluminates in bright blue when the TV is in standby mode.Illuminates in dark blue when the TV is switched on.Remote control sensorAccepts the IR signal of remote controller.Here shown may be somewhat different from your set.NNNNOOOOTTTTEEEE
Controls And Connectors11Rear PanelHere shown may be somewhat different from your set.NNNNOOOOTTTTEEEE1. RGB IN (PC)Connect to the video output jack on your PC.2. AUDIO IN (RGB/DVI)Connect to the audio output jack on your PC.3. HDMI/DVI1 INConnect to the HDMI jack for device with HDMI out-put. (This input can also be used as a DVI connec-tion with an HDMI to DVI adaptor and separate ana-log audio inputs.)4. HDMI2 INConnect to the HDMI jack for device with HDMI out-put. 5. HDMI3 INConnect to the HDMI jack for device with HDMI out-put. 6. COMPONENT1 IN (YPbPr1)Video/Audio inputs for Component1.7. COMPONENT2 IN (YPbPr2)Video/Audio inputs for Component2.8. AV INConnect RCA cable to an appropriate external A/Vdevice such as VCR, DVD or Camcorder.9. S-VIDEO INConnect the output of an S-VIDEO device to the S-VIDEO input.10. USB INConnect the USB memory stick.11. DIGITAL AUDIO OUT(OPTICAL)Connect digital audio to various types of equipment.12. ANTENNA/CABLE INConnect to your antenna or cable box for TV signal.13. SERVICE14.EXTERNAL SPEAKER OUTExternal Speaker outputs.15. AC INThis TV operates on an AC power.
Controls And Connectors12- All the functions can be controlled with the remote control handset.- Some functions can also be adjusted with the buttons on the side panel of the set.- Before using remote control handset, please install the batteries.Remote Control123456789_0PRE.CHFAV.CHMUTEEPG SLEEPMENU EXITVOL CHINFO MTS RATIO CCPICTURE SOUNDPHOTO MUSICPIPPIPINPUTSWAPPIPCH+AUD.SWAP SIZEPOSITION PIPCH-SOURCEOKNUMBER BUTTONSSelects channel numbers.Hyphen( )Press to select DTV channels.For example, to select channel ‘10-1’, press ‘10’ then press ‘ ’ and ‘1’.PRE.CHSwitch to the previous channel number.VOL + / VOL -Adjusts sound level.CH + / CH -Select a channel.FAV.CHDisplay the favorite channel list.MUTESwitches the sound on or off.MENUDisplay on screen menus.EXITClear all on-screen menus and return to TV viewing from anymenu.Navigational ControlsAdjusts menu settings.Selects menu item.OKAccepts your selection.EPGDisplays the program guide.SLEEPSets the sleep timer.POWERSwitches the set on or off.SOURCESelects the TV, AV/S-Video, Component-1, Component-2,HDMI 1, HDMI 2, HDMI 3 or VGA mode.
Controls And Connectors13123456789_0PRE.CHFAV.CHMUTEEPG SLEEPMENU EXITVOL CHINFO MTS RATIO CCPICTURE SOUNDPHOTO MUSICPIPPIPINPUTSWAPPIPCH+AUD.SWAP SIZEPOSITION PIPCH-SOURCEOKINFODisplay the current channel information.MTSSelect MTS sound : Mono, Stereo and SAP in AnalogChannel.Change the audio language in DTV Channel.RATIOSelects your desired picture format.CCSelect the Caption menu directly.PICTURERecalls your preferred picture setting.SOUNDRecalls your preferred sound setting.PHOTOSelect the Photos mode directly.MUSICSelect the Music mode directly.PIPSwitches the sub picture on or off.PIP INPUTNot Support.SWAPNot Support.AUD.SWAPAlternates between main and sub picture audio.SIZENot Support.POSITIONMoves the sub picture position.PIP CH +/PIP CH -Select a channel for the sub picture.
Installation14InstallationWall mount Installation4 inches4 inches4 inches4 inches4 inchesThe set can be installed on a wall as shown above.For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.Detailed instructions are available from your dealer, refer to the optional Wall Mounting Bracket Installation andSetup Guide. (Wall Mount Sold Separately)Desktop Pedestal Installation4 inches4 inches4 inches4 inchesThe set can be mounted on a desk as shown above.For proper ventilation, allow a clearance of 4 inches on each side from the wall.Detailed instructions are available from your dealer, refer to the optional Desktop Stand Installation and SetupGuide.- Do not install the Wall-Mount except the Qualified Service Personnel.NNNNOOOOTTTTEEEE
Connections15ConnectionsAntenna ConnectionANTENNA/CABLE INVIDEOAVAUDIOLRS-VIDEO USBDIGITAL AUDIOOUT(OPTICAL)SERVICEMulti-family Dwellings/ Apartments(Connect to wall antenna socket)Single-family Dwellings /Houses(Connect to wall jack for outdoor antenna)Wall Antenna SocketRF Coaxial Wire (75 ohm)VHFUHFOutdoor AntennaTurn clockwise to tighten.Be careful not to bend the bronze wire whenconnecting to an antenna port.* Separately purchase a RF Coaxial Wire(75 ohm)-To improve the picture quality in a poor signalarea, please purchase a signal amplifier andinstall properly.-If the antenna is not installed properly, contactyour dealer for assistance.NNNNOOOOTTTTEEEEANTENNA/CABLE INVIDEOAVAUDIOLRS-VIDEO USBDIGITAL AUDIOOUT(OPTICAL)SERVICEVHF UHFSignalAmplifierRear panel of the setRear panel of the set
Connections16- To avoid picture noise (interface), leaves an adequate distance between the TV and the VCR.VCR ConnectionANTENNA/CABLE INVIDEOAVAUDIOLRS-VIDEO USBDIGITAL AUDIOOUT(OPTICAL)SERVICEANT INANT OUT S-VIDEOINOUT(R) AUDIO (L) VIDEO1. Connect the Antenna out socket of the VCR to theAntenna input socket on the TV.2. Press the POWER button on the VCR and matchthe appropriate input selection between the TVand VCR for viewing.AAWhen connecting with an antennaVIDEOAVAUDIOLRS-VIDEO USBCOMPONENT 1LRVIDEOYPb PrAUDIOCOMPONENT 2LRVIDEOYPb PrAUDIOANT INANT OUT S-VIDEOINOUT(L) AUDIO (R)VIDEOOUTPUTSWITCH1. Connect the AUDIO/VIDEO jacks between TVand VCR. Match the jack colors (Video = yellow,Audio Left = white, and Audio Right = red)2. Insert a video tape into the VCR and press PLAYon the VCR. 3. Select the AV/S-Video input source with using theSOURCE button on the remote control.4. Refer to the VCR manual for operating instruc-tions.AAWhen connecting with a RCA cableVCRRear panel of the setVCRRear panel of the set
Connections17VIDEOAVAUDIOLRS-VIDEO USBCOMPONENT 1LRVIDEOYPb PrAUDIOCOMPONENT 2LRVIDEOYPb PrAUDIOANT INANT OUT S-VIDEOINOUT(L) AUDIO (R)VIDEOOUTPUTSWITCH1. Connect the S-VIDEO output of the VCR to the S-VIDEO input on the set. The picture quality isimproved; compared to normal composite (RCAcable) input.2. Connect the audio outputs of the VCR to the AVAUDIO L,Rinput jacks on the set.3. Insert a video tape into the VCR and press PLAYon the VCR. 4. Select the AV/S-Video input source with using theSOURCE button on the remote control.5. Refer to the VCR manual for operating instructions.AAWhen connecting with a S-Video cableVCRRear panel of the set
Connections18DVD ConnectionVIDEOAVAUDIOLRS-VIDEO USBCOMPONENT 1LRVIDEOYPb PrAUDIOCOMPONENT 2LRVIDEOYPb PrAUDIOANT INANT OUT S-VIDEOINOUT(L) AUDIO (R)VIDEOOUTPUTSWITCH1. Connect the S-VIDEO output of the DVD to the S-VIDEO input on the set.2. Connect the audio outputs of the DVD to the AVAUDIO L, Rinput jacks on the set.3. Turn on the DVD player, insert a DVD.4. Select AV/S-Video input source with using theSOURCE button on the remote control.5. Refer to the DVD player's manual for operatinginstructions.AAWhen connecting with a S-Video cableDVDRear panel of the setVIDEOAVAUDIOLRS-VIDEO USBCOMPONENT 1LRVIDEOYPb PrAUDIOCOMPONENT 2LRVIDEOYPb PrAUDIO(L) AUDIO (R)YPb Pr1. Connect the video outputs (Y, PB, PR) of the DVDto the COMPONENT1 VIDEO(Y, Pb, Pr1) orCOMPONENT2 VIDEO(Y,Pb,Pr2) jacks on theset.2. Connect the audio outputs of the DVD to theCOMPONENT1 AUDIO L, Ror COMPONENT2AUDIO L, R jacks on the set.3. Turn on the DVD player, insert a DVD.4. Select Component-1 or Component-2 sourcewith using the SOURCE button on the remotecontrol.5. Refer to the DVD player's manual for operatinginstructions.AAWhen connecting with a Component CableDVDRear panel of the set
Connections191. Connect the HDMI output of the DVD to theHDMI/DVI1 IN, HDMI2 IN or HDMI3 IN jack onthe set.2. Select HDMI 1, HDMI 2 or HDMI 3 input sourcewith using the SOURCE button on the remotecontrol.3. Refer to the DVD player's manual for operatinginstructions.AAWhen connecting with a HDMI cableHDMI IN2HDMI IN3RGB IN(PC) AUDIO IN(RGB/DVI)HDMI/DVI IN 1HDMI-DVD OUTPUTDVDRear panel of the set
Connections20-This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box.However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to thefigure as shown below.HDSTB ConnectionHDMI IN2HDMI IN3RGB IN(PC) AUDIO IN(RGB/DVI)HDMI/DVI IN 1(R) AUDIO (L) RGB-DTV OUTPUT1. Connect the RGB output of the digital set-top boxto the RGB IN (PC) jack on the set.2. Connect the audio outputs of the set-top box tothe AUDIO IN (RGB/DVI) jack on the set.3. Turn on the digital set-top box.4. Select VGA input source with using the SOURCEbutton on the remote control.5. Refer to the digital set-top box manual for operat-ing instructions.AAWhen connecting with a D-Sub 15 pin cableDigital Set-top BoxRear panel of the set1. Connect the HDMI output of the digital set-topbox to the HDMI/DVI1 IN, HDMI2 IN or HDMI3 INjack on the set.2. Turn on the digital set-top box.3. Select HDMI 1, HDMI 2 or HDMI 3 input sourcewith using the SOURCE button on the remotecontrol.4. Refer to the digital set-top box manual for operat-ing instructions.AAWhen connecting with a HDMI cableHDMI IN2HDMI IN3RGB IN(PC) AUDIO IN(RGB/DVI)HDMI/DVI IN 1HDMI-DVD OUTPUTDigital Set-top BoxRear panel of the set
Connections21VIDEOAVAUDIOLRS-VIDEO USBCOMPONENT 1LRVIDEOYPb PrAUDIOCOMPONENT 2LRVIDEOYPb PrAUDIO(L) AUDIO (R)YPb Pr1. Connect the video outputs (Y, PB, PR) of the digi-tal set-top box to the COMPONENT1 VIDEO(Y,Pb, Pr1) or COMPONENT2 VIDEO(Y,Pb,Pr2)jacks on the set.2. Connect the audio outputs of the digital set-topbox to the COMPONENT1 AUDIO L,R or COM-PONENT2 AUDIO L,Rjacks on the set.3. Turn on the digital set-top box.4. Select Component-1 or Component-2 sourcewith using the SOURCE button on the remotecontrol.5. Refer to the digital set-top box manual for operat-ing instructions.AAWhen connecting with a Component cableDigital Set-top BoxRear panel of the setDVI-DTV OUTPUT (R) AUDIO (L)HDMI IN2HDMI IN3RGB IN(PC) AUDIO IN(RGB/DVI)HDMI/DVI IN 11. Connect the DVI output of the digital set-top boxto the HDMI/DVI1 IN jack on the set.2. Connect the audio outputs of the set-top box tothe AUDIO IN (RGB/DVI) jack on the set.3. Turn on the digital set-top box.4. Select HDMI 1 input source with using theSOURCE button on the remote control.5. Refer to the digital set-top box manual for operat-ing instructions.aAAWhen connecting with a HDMI to DVI cableRear panel of the setDigital Set-top Box
Connections22External A/V SourceL-AUDIO-RVIDEOOUTVIDEOAVAUDIOLRS-VIDEO USBCOMPONENT 1LRVIDEOYPb PrAUDIOCOMPONENT 2LRVIDEOYPb PrAUDIO1. Connect the AUDIO/VIDEO jacks between TVand external equipment. Match the jack colors(Video = yellow, Audio Left = white, and AudioRight = red)2. Select the AV/S-Video input source with using theSOURCE button on the remote control.3. Operate the corresponding external equipment.4. Refer to the external equipment manual for oper-ating instructions.Camcorder Video game setRear panel of the setDigital Audio OutANTENNA/CABLE INVIDEOAVAUDIOLRS-VIDEO USBDIGITAL AUDIOOUT(OPTICAL)SERVICEDIGITAL AUDIOIN(COAXIAL)1. Connect one end of the optical cable to the TV’sDIGITAL AUDIO OUT(OPTICAL) port.2. Connect the other end of the optical cable to thedigital audio input on the audio equipment.3. Refer to the external audio equipment manual foroperation.Audio EquipmentRear panel of the set
Connections23USB in setupANTENNA/CABLE INVIDEOAVAUDIOLRS-VIDEO USBDIGITAL AUDIOOUT(OPTICAL)SERVICE1. Connect the USB device to the USB IN jack onthe set.2. After connecting the USB IN jack, you can usethe Photos/Music function.3. Select the Photos or Music input source withusing the PHOTO or MUSIC button on the remotecontrol.Rear panel of the setUSB Memory
Connections24PC ConnectionHDMI IN2HDMI IN3RGB IN(PC) AUDIO IN(RGB/DVI)HDMI/DVI IN 1AUDIO OUT PC OUTPUT1. Connect the RGB output of the PC to the RGBIN(PC) jack on the set.2. Connect the PC audio outputs to the AUDIO IN(RGB/DVI) jack on the set.3. Turn on the PC and the set.4. Select VGA input source with using the SOURCEbutton on the remote control.AAWhen connecting with a D-Sub 15 pin cablePCRear panel of the setDVI OUTPUT AUDIO OUTHDMI IN2HDMI IN3RGB IN(PC) AUDIO IN(RGB/DVI)HDMI/DVI IN 11. Connect the DVI output of the PC to theHDMI/DVI IN jack on the set.2. Connect the PC audio outputs to the AUDIO IN(RGB/DVI) jack on the set.3. Turn on the PC and the set.4. Select HDMI 1 input source with using theSOURCE button on the remote control.AAWhen connecting with a HDMI to DVI cablePCRear panel of the set
25ConnectionsResolutiona. The synchronization input form is separated.b. If the resolution is not supported, ‘Not Support!’ message will be displayed.NNNNOOOOTTTTEEEE31.46937.87948.36347.77647.71247.13059.94160.31760.00459.87060.01559.650HorizontalFrequency (kHz)VerticalFrequency (Hz)640 x 480800 x 6001024 x 7681280 x 7681360 x 7681366 x 768Resolution480/60P720/60P1080/60I1080/60P640 x 480800 x 6001024 x 7681280 x 7681360 x 7681366 x 76860.00060.00060.00060.00059.94061.31760.00459.99560.01559.650Resolution VerticalFrequency (Hz)VIDEOPCAAPCAAHDMI
26Basic OperationTurning On or OffStandby Setup: The AC power cord must be connected to have the TV in standby mode and ready tobe turned on. Press the ON/OFF button on the side panel of the TV to go into standby mode.1. If the TV is in standby mode, press the POWER button on the remote or the TV itself to turn the TV on.2. Press the POWER button again on the remote controller or the TV itself to turn the TV off.Channel SelectionYou can select a channel number with the CH / CH button or NUMBER buttons.Sound MutePress the MUTE button. The sound is switched off and the mute display appears.To cancel mute mode, press the MUTE or VOL+ / VOL- button again.Quick ViewPress the PRE.CH button to view the last channel you were watching.Volume AdjustmentPress the VOL+ / VOL- button to adjust the sound level.Basic Operation
Basic Operation27Input Selection1. Press the SOURCE button to display the SourceSelection.2. Press the Down or Up button to select your desiredmode.3. Press the OK button to change your selected mode.Language Selection1. Press the MENU button and then press the Down or Upbutton to select the Option.2. Press the OK button and then press the Down or Upbutton to select Menu Language.3. Press the Down or Up button to select your desired lan-guage and then press the OK button.(Select between English, French, Spanish, German)4. The on screen menu will then appear in theselected language.Source SelectionTVAV/S-VideoComponent-1Component-2HDMI 1HDMI 2HDMI 3VGAOptionMenu LanguageAudio LanguageInput LabelCaptionPC SettingPIP SettingMenu OpacityEnglishEnglishMediumMove SelectOK CloseMenuFFGGDDEEOptionMenu LanguageAudio LanguageInput LabelCaptionPC SettingPIP SettingMenu OpacityEnglishEnglishMediumMove SelectOK CloseMenuFFGGDDEEEnglishFrenchSpanishGerman
On Screen Menus28On Screen MenusYour TV’s OSD (On Screen Display) may differ slightly from what is shown in this manual.1. Press the MENU button on enter the on-screen menu and then use either the Down or Up button to select eachsub-menu.2. Press the OK button and then use Down,Up,Left and Right buttons to navigate to the available menus.ChannelsChannel ScanFind ChannelChannel EditMove SelectOK CloseMenuFF GGDDEEChannels MENUPicturePicture ModeUser SettingDynamic ContrastAdvanced PictureAspect RatioPicture ResetStandardOffWideMove SelectOK CloseMenuFF GGDDEEPicture MENULockLock SystemSet PasswordBlock ChannelRatingOffMove SelectOK CloseMenuFF GGDDEELock MENUAudioSound ModeUser SettingSpeakerAuto VolumeDigital OutputAudio ResetStandardOnOnPCMMove SelectOK CloseMenuFF GGDDEEAudio MENUOptionMenu LanguageAudio LanguageInput LabelCaptionPC SettingPIP SettingMenu OpacityEnglishEnglishMediumMove SelectOK CloseMenuFF GGDDEEOption MENUTimerClockTimerSleep Timer OffMove SelectOK CloseMenuFF GGDDEETimer MENU
Setting up TV Channel29Setting up the TV ChannelsAutomatically finds all channels available through the Antenna or Cable and stores them in memory onthe channel list.Auto Scan1. Press the MENU button and then press the Down orUp button to select the Channels.2. Press the OK button and then press the Down or Upbutton to select Channel Scan.3. Press the OK button and then press the Left or Rightbutton to select OK or Cancel.4. Press the OK button and then press the Down or Upbutton to select Antenna or Cable.5. Press the OK button to start auto search.The TV will begin memorizing all of the available chan-nels.6. Select the Cancel and then press the OK button at anytime to interrupt the memorization process.ChannelsMove SelectOK CloseMenuFF GGDDEEChannel ScanFind ChannelChannel EditStart full channel scan process.This will erase entire existing channels.Are you sure to continue?Channel ScanOK CancelSelect the source for yourtelevision signalChannel ScanCableAntennaNow Scanning..Channel ScanCancelChannels FoundDigital: 0Analog: 11%
30Setting up TV ChannelYou can directly enter the channel number you want to find and find the entered channel.Find Channel1. Press the MENU button and then press the Down orUp button to select the Channels.2. Press the OK button and then press the Down or Upbutton to select Find Channel.3. Press the OK button and then press the number buttonto select channel number you want to find.4. Press the Left or Right button to select Find or Done.If you want to add selected channel, select Find withusing Left button. Then press the OK button. Otherwise select Done.5. Press the MENU button to return to the previous menu.ChannelsMove SelectOK CloseMenuFF GGDDEEChannel ScanFind ChannelChannel EditEnter the RFChannel Number.Contact your localstation or cableoperator for thisinformation.Find ChannelFind DoneMove SelectOKEnterNum CloseMenuFF GG-Enter the RFChannel Number.Contact your localstation or cableoperator for thisinformation.Find ChannelFind Done9-0Move SelectOKEnterNum CloseMenuFF GG-
31Setting up TV ChannelYou can manually store or remove channels in whatever order you desire.From the default channel list created from the Channel Scan channel search, you can create two different types ofchannel lists in memory: Channel List and Favorite Channel List.Add / Delete a Channel1. Press the MENU button and then press the Down orUp button to select the Channels.2. Press the OK button and then press the Down or Upbutton to select Channel Edit.3. Press the OK button and then press the Down or Upbutton to select channel you want to add or delete.Channel List:Press the OK button to add or delete channel to theChannel List.When the icon is shown, the channel will be delet-ed.Favorite Channel List:Press the FAV.CH button to add or delete channel tothe Favorite Channel List.The icon will appear.When the icon is displayed, the selected channel is set as favorites.4. Save the other channels in the same method.5. Press the MENU button to return to the previous menu.DELFAVFAVChannelsMove SelectOK CloseMenuFF GGDDEEChannel ScanFind ChannelChannel EditChannel EditMoveCloseMenuDDEEToggle DeleteOKToggle FavoriteFavMove PageCH DDEE9-010-011-012-0DELChannel EditMoveCloseMenuDDEEAdd/DeleteOKToggle FavoriteFavMove PageCH DDEE9-010-011-012-0FAV
32Setting up TV ChannelDisplays Broadcasting guide of received channel.EPG (Electronic Program Guide)1. Press the EPG button to display the Electronic Program Guide.2. To exit the Electronic Program Guide, press the EPG button again.International News23:0023:1024:3006:3008:3009:00Hurricane like is forecast to make landfallin Texas early Saturday morning as a dangerousProgram GuideMove CloseEPGDDEEInternational NewsNo Info AvailableNo Info Available
33Picture ControlsPicture Mode adjusts the set for the best picture appearance.Select the preset value in the Picture Mode menu.Auto Picture Controls1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Picture,then press the OK button.3. Press the Down or Up button to select Picture Mode,then press the OK button.4. Press the Down or Up button to select Mild,Standard,Dynamic or User, then press the OK button.5. Press the MENU button to return to the previous menu.MildSelect this option to display with a soft image.StandardThe most general and natural screen display status.DynamicSelect this option to display with a sharp image.UserSelect this option to use the user-defined setting.-If you want to select Picture Mode directly, press the PICTURE button.-Every time you press the button, it will switch between Mild,Standard,Dynamic or User.NNNNOOOOTTTTEEEEPicture ControlsPictureMove SelectOK CloseMenuFF GGDDEEPicture ModeUser SettingDynamic ContrastAdvanced PictureAspect RatioPicture ResetStandardOffWidePictureMove SelectOK CloseMenuFF GGDDEEPicture ModeUser SettingDynamic ContrastAdvanced PictureAspect RatioPicture ResetStandardOffWideMildStandardDynamicUser
34Picture ControlsYou can adjust picture Contrast,Brightness, Color, Tint and Sharpness to the levels you prefer.Manual Picture Controls1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Picture,then press the OK button.3. Press the Down or Up button to select User Setting,then press the OK button.4. Press the Down or Up button to select desired pictureoption.(Contrast, Brightness, Color, Tint, Sharpness)5. Press the OK button and then press the Left or Rightbutton to make appropriate adjustments.6. Press the MENU button to return to the previous menu.ContrastAdjusts the difference between the light and dark lev-els in the picture.BrightnessIncreases or decreases amount of white in the yourpicture.ColorAdjusts intensity of all colors.TintAdjusts the balance between red and green levels.SharpnessAdjusts the level of sharpness in the edges betweenthe light and dark areas of the picture. The lower thelevel, the softer the image.PictureMove SelectOK CloseMenuFF GGDDEEPicture ModeUser SettingDynamic ContrastAdvanced PictureAspect RatioPicture ResetStandardOffWidePicture > User SettingAdjust SelectOK Go BackMenuFF GGMoveDDEEContrastBrightnessColorTintSharpnessColor Temperature8050505050NeutralContrast 80-The adjustment of Color, Tint and Sharpness is not allowed when the current source is VGA.NNNNOOOOTTTTEEEE
35Picture ControlsYou can adjust to color temperature you prefer.Color Temperature1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Picture,then press the OK button.3. Press the Down or Up button to select User Setting,then press the OK button.4. Press the Down or Up button to select ColorTemperature, then press the OK button.5. Press the Down or Up button to select Cool,Warm orNeutral, then press the OK button.6. Press the MENU button to return to the previous menu.Picture > User SettingAdjust SelectOK Go BackMenuFF GGMoveDDEEContrastBrightnessColorTintSharpnessColor Temperature8050505050NeutralPicture > User SettingAdjust SelectOK CloseMenuFF GGMoveDDEEContrastBrightnessColorTintSharpnessColor Temperature8050505050NeutralPictureMove SelectOK CloseMenuFF GGDDEEPicture ModeUser SettingDynamic ContrastAdvanced PictureAspect RatioPicture ResetStandardOffWideCoolWarmNeutral
36Optimizing the contrast automatically according to the video signal.Dynamic Contrast1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Picture,then press the OK button.3. Press the Down or Up button to select DynamicContrast.4. Press the OK button to select On or Off.5. Press the MENU button to return to the previous menu.Picture ControlsPictureMove SelectOK CloseMenuFF GGDDEEPicture ModeUser SettingDynamic ContrastAdvanced PictureAspect RatioPicture ResetStandardOffWidePictureMove SelectOK CloseMenuFF GGDDEEPicture ModeUser SettingDynamic ContrastAdvanced PictureAspect RatioPicture ResetStandardOnWide
Picture Controls37Picture > Advanced SettingMove SelectOK Go BackMenuFF GGDDEENoise ReductionFlesh Tone CorrectionBlue StretchFilm ModeOnOffOffOffUse this feature to reduce picture artifacts caused by the digitizing of image motion content that may be present inthe picture.Noise Reduction1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Picture,then press the OK button.3. Press the Down or Up button to select AdvancedPicture, then press the OK button.4. Press the Down or Up button to select NoiseReduction, then press the OK button.5. Press the Down or Up button to select Off or On, thenpress the OK button.6. Press the MENU button to return to the previous menu.PictureMove SelectOK CloseMenuFF GGDDEEPicture ModeUser SettingDynamic ContrastAdvanced PictureAspect RatioPicture ResetStandardOnWideOffOnPicture > Advanced SettingMove SelectOK Go BackMenuFF GGDDEENoise ReductionFlesh Tone CorrectionBlue StretchFilm ModeOnOffOffOff
Picture Controls38In some cases, activation of this feature can result in a more pleasing production of sky and flesh color. For example, the skin color of human will be shown more naturally.Flesh Tone Correction1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Picture,then press the OK button.3. Press the Down or Up button to select AdvancedPicture, then press the OK button.4. Press the Down or Up button to select Flesh ToneCorrection.5. Press the OK button to select On or Off.6. Press the MENU button to return to the previous menu.PictureMove SelectOK CloseMenuFF GGDDEEPicture ModeUser SettingDynamic ContrastAdvanced PictureAspect RatioPicture ResetStandardOnWidePicture > Advanced SettingMove SelectOK Go BackMenuFF GGDDEENoise ReductionFlesh Tone CorrectionBlue StretchFilm ModeOnOffOffOff
Picture Controls39This is the function to make the white color look bluer.Blue Stretch1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Picture,then press the OK button.3. Press the Down or Up button to select AdvancedPicture, then press the OK button.4. Press the Down or Up button to select Blue Stretch.5. Press the OK button to select On or Off.6. Press the MENU button to return to the previous menu.PictureMove SelectOK CloseMenuFF GGDDEEPicture ModeUser SettingDynamic ContrastAdvanced PictureAspect RatioPicture ResetStandardOnWidePicture > Advanced SettingMove SelectOK Go BackMenuFF GGDDEENoise ReductionFlesh Tone CorrectionBlue StretchFilm ModeOnOffOffOff
Picture Controls40By controlling Film Mode for the screen lag or shaking that can occur during the conversion from movie to TV videosignal, you can view the movie in as good condition as master copy through your TV.Film Mode1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Picture,then press the OK button.3. Press the Down or Up button to select AdvancedPicture, then press the OK button.4. Press the Down or Up button to select Film Mode.5. Press the OK button to select On or Off.6. Press the MENU button to return to the previous menu.PictureMove SelectOK CloseMenuFF GGDDEEPicture ModeUser SettingDynamic ContrastAdvanced PictureAspect RatioPicture ResetStandardOnWidePicture > Advanced SettingMove SelectOK Go BackMenuFF GGDDEENoise ReductionFlesh Tone CorrectionBlue StretchFilm ModeOnOffOffOff
Picture Controls41You can watch the screen in various picture formats.Screen size selection depends on the type of video input.Aspect Ratio1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Picture,then press the OK button.3. Press the Down or Up button to select Aspect Ratio,then press the OK button.4. Press the Down or Up button to select Auto,Wide,Zoom1 or Zoom2, then press the OK button.5. Press the MENU button to return to the previous menu.AutoWhen your set receives the wide screen signal, it willchange automatically the picture format that has beensent.WideYou can enjoy the cinema or general TV programthrough the 16:9 mode.ZOOM1The screen size when Wide screen is verticallyenlarged.ZOOM2This is the function to enlarge the screen sizevertically than ZOOM1.PictureMove SelectOK CloseMenuFF GGDDEEPicture ModeUser SettingDynamic ContrastAdvanced PictureAspect RatioPicture ResetStandardOnWidePictureMove SelectOK CloseMenuFF GGDDEEPicture ModeUser SettingDynamic ContrastAdvanced PictureAspect RatioPicture ResetStandardOnWideAutoWideZoom1Zoom2-If you want to select Aspect Ratio directly, press the RATIO button.-Every time you press the button, it will switch between Auto,Wide,Zoom1 or Zoom2.NNNNOOOOTTTTEEEE
Picture Controls42Use to quickly reset all the Picture menu options to their original factory preset values.Reset Picture Mode1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Picture,then press the OK button.3. Press the Down or Up button to select Picture Reset,then press the OK button.4. Confirmation OSD will appear.If you want to return the picture setting to factorydefault you can select OK button and then press theOK button.5. Press the MENU button to return to the previous menu.PictureMove SelectOK CloseMenuFF GGDDEEPicture ModeUser SettingDynamic ContrastAdvanced PictureAspect RatioPicture ResetStandardOnWidePictureMove SelectOK CloseMenuFF GGDDEEPicture ModeUser SettingDynamic ContrastAdvanced PictureAspect RatioPicture ResetStandardOnWidePicture ResetAre you sure to continue?Yes No
Sound Controls43This Sound Mode automatically adjusts the sound controls to the recommended settings.Auto Sound Controls1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Audio,then press the OK button.3. Press the Down or Up button to select Sound Mode,then press the OK button.4. Press the Down or Up button to select Standard,Music,Movie or User, then press the OK button.5. Press the MENU button to return to the previous menu.StandardThe most commanding and natural audio.MusicSelect this option to enjoy the original sound whenlistening to the music.MovieSelect this option to enjoy sublime sound.UserSelect this option to manually adjust the audio settings.Sound ControlsAudioMove SelectOK CloseMenuFF GGDDEESound ModeUser SettingSpeakerAuto VolumeDigital OutputAudio ResetStandardOnOnPCMAudioMove SelectOK CloseMenuFF GGDDEESound ModeUser SettingSpeakerAuto VolumeDigital OutputAudio ResetStandardOnOnPCMStandardMusicMovieUser-If you want to change the Sound Mode without entering the menus, press the SOUND button.-Each time you press the button, it will switch between Standard,Music,Movie and User.NNNNOOOOTTTTEEEE
44Sound ControlsThis function allows you to manually adjust the audio settings to your preferred levels.Manual Sound Controls1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Audio,then press the OK button.3. Press the Down or Up button to select User Setting,then press the OK button.4. Press the Down or Up button to select desired pictureoption.(Treble, Bass, Balance) 5. Press the Left or Right button to make appropriateadjustments.6. Press the MENU button to return to the previous menu.TrebleThis adjusts the range of the high pitch sound.BassThis adjusts the range of the low pitch sound.BalanceAdjusts the left to right sound balance between thebuilt-in speakers.AudioMove SelectOK CloseMenuFF GGDDEESound ModeUser SettingSpeakerAuto VolumeDigital OutputAudio ResetStandardOnOnPCMAudio > User SettingMove AdjustFF GGGo BackMenuDDEETrebleBassBalance25250
45Sound ControlsTurn the TV speakers off if using external audio equipment.Feature turns the Speaker option On or Off.Speaker On/Off1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Audio,then press the OK button.3. Press the Down or Up button to select Speaker.4. Press the OK button to select On or Off.5. Press the MENU button to return to the previous menu.AudioMove SelectOK CloseMenuFF GGDDEESound ModeUser SettingSpeakerAuto VolumeDigital OutputAudio ResetStandardOnOnPCMAudioMove SelectOK CloseMenuFF GGDDEESound ModeUser SettingSpeakerAuto VolumeDigital OutputAudio ResetStandardOffOnPCM
46Sound ControlsThis function automatically stabilizes the volume level while changing to channels with different audio levels.Auto Volume Control1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Audio,then press the OK button.3. Press the Down or Up button to select Auto Volume.4. Press the OK button to select On or Off.5. Press the MENU button to return to the previous menu.AudioMove SelectOK CloseMenuFF GGDDEESound ModeUser SettingSpeakerAuto VolumeDigital OutputAudio ResetStandardOnOnPCMAudioMove SelectOK CloseMenuFF GGDDEESound ModeUser SettingSpeakerAuto VolumeDigital OutputAudio ResetStandardOnOffPCM
47Sound ControlsPCM (Pulse-code modulation)This mode creates a digital representation of an ana-log siginal and is only used with an audio CD signal.Dolby DigitalTelevision will output a digital audio signal.Manufactured under license fromDolby Laboratories.“ Dolby “and the double-D symbolare trademarks of DolbyLaboratories.This option activates Digital Audio Output. This is recommended for use with other devices capable of receiving dig-ital audio signals. (This mode is set to Off by default)Digital Output1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Audio,then press the OK button.3. Press the Down or Up button to select DigitalOutput, then press the OK button.4. Press the Down or Up button to select PCM orDolby, then press the OK button.5. Press the MENU button to return to the previous menu.AudioMove SelectOK CloseMenuFF GGDDEESound ModeUser SettingSpeakerAuto VolumeDigital OutputAudio ResetStandardOnOnPCMAudioMove SelectOK CloseMenuFF GGDDEESound ModeUser SettingSpeakerAuto VolumeDigital OutputAudio ResetStandardOnOnPCMPCMDolby<Dolby Digital>
48Sound ControlsUse to quickly reset all the Audio menu options to their original factory preset values.Reset Audio Mode1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Audio,then press the OK button.3. Press the Down or Up button to select Audio Reset,then press the OK button.4. Confirmation OSD will appear.If you want to return the audio setting to factory defaultyou can select OK button and then press the OK but-ton.5. Press the MENU button to return to the previous menu.AudioMove SelectOK CloseMenuFF GGDDEESound ModeUser SettingSpeakerAuto VolumeDigital OutputAudio ResetStandardOnOnPCMAudioMove SelectOK CloseMenuFF GGDDEESound ModeUser SettingSpeakerAuto VolumeDigital OutputAudio ResetStandardOnOnPCMAudio ResetAre you sure to continue?Yes NoThis TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that the station may transmit.The television will automically switch to Mono sound if the broadcasted channel is transmitted in Mono.Also, you can manually select Mono if you want to listen to a stereo or SAP broadcasted channel in Mono.1. Use the MTS button to select your desired MTS mode in analog signal.Each time you press the MTS button, Mono, Stereo, or SAP appear in turn.If other languages available on the digital signal, select them with the MTS button.2. Press EXIT button to save and return to TV viewing.Stereo/SAP Broadcast Setup
49Time SettingThe time is set automatically from a digital channel signal.The digital channel signal includes information for the current time provided by the broadcasting station. Set thetime manually if the current time is set incorrectly by the Auto Synchronization function.Auto Time Setting1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Timer,then press the OK button.3. Press the Down or Up button to select Clock, thenpress the OK button.4. Press the Up button to select Time Zone, then pressthe OK button.5. Press the Down or Up button to select your viewingarea time zone, then press the OK button.(Alaska, Hawaii, Pacific, Mountain, Central, Eastern,Atlantic, Newfoundland, Samoa)6. Press the Down or Up button to select AutomaticTime, then press the OK button.7. Press the Down or Up button to select DaylightSaving Time, then press the OK button, depending onwhether or not your viewing area observes DaylightSaving Time.8. Press the Left or Right button to select OK or Cancel,then press the OK button.If you want to save the setting, select OK and if not,select Cancel.9. Press the MENU button to return to the previous menu.Time SettingTimerMove SelectOK CloseMenuFF GGDDEEClockTimerSleep Timer OffClockOK CancelMove SelectOKEnterNum CloseMenuFF GGDDEEYear MonthTime ZoneAutomatic TimeDaylight Saving TimeDay Hour Minute2009 2 10 9 47 PM EPacific(US/CAN)EClockOK CancelMove SelectOKEnterNum CloseMenuFF GGDDEEYear MonthTime ZoneAutomatic TimeDaylight Saving TimeDay Hour Minute2009 2 10 9 47 PM EPacific(US/CAN)EAlaska (US)Hawaii (US)Pacific (US/CAN)Mountain (US/CAN)Central (US/CAN)
50If the current time setting is wrong, this function allows you to set the clock manually.Manual Time Setting1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Timer,then press the OK button.3. Press the Down or Up button to select Clock, thenpress the OK button.4. Press the Left or Right button to select either the Year,Month, Day, Hour or Minute option. Once selected, use the number button to set the Year,Month, Day, Hour and Minute options.5. Press the Left or Right button to select AM/PM, thenpress the OK button.6. Press the Down or Up button to select AM or PM,thenpress the OK button.7. Press the Left or Right button to select OK or Cancel,then press the OK button.If you want to save the setting, select OK and if not,select Cancel.8. Press the MENU button to return to the previous menu.-If Automatic Time is marked, Year, Month, Day, Hour and Minute are cannot be adjusted.NNNNOOOOTTTTEEEETimerMove SelectOK CloseMenuFF GGDDEEClockTimerSleep Timer OffClockOK CancelMove SelectOKEnterNum CloseMenuFF GGDDEEYear MonthTime ZoneAutomatic TimeDaylight Saving TimeDay Hour Minute2009 2 10 9 47 PM EPacific(US/CAN)ETime Setting
51Time SettingThe timer function operates only if the current time has been set.The TV turns on automatically with the Timer function.Auto On/Off Time Setting1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Timer,then press the OK button.3. Press the Down or Up button to select Timer, thenpress the OK button.4. Press the Left or Right button to select day option. Once selected, use the OK button to set the day.5. Press the Down or Up button to select Time On,OnTime, Source/Channel or Off Time.Time On: Set the Timer function On or Off.On Time: Set the start time at turn-on.Source/Channel: Set the source and channel at turn-on.Off Time: Set the start time at turn-off.6. Press the Left or Right button to move the positionand then press the OK button.7. Once selected, use the Down or Up buttons to set theOn Time, Source/Channel or Off Time, then press theOK button.8. Press the Left or Right button to select OK or Cancel.9. Press the MENU button to return to the previous menu.TimerMove SelectOK CloseMenuFF GGDDEEClockTimerSleep Timer OffTimerOK CancelMove SelectOK CloseMenuFF GGDDEEOn TimeSource/Channel12 E00 EAM EOff Time 12 E00 EAM ETimer On Off ETVE7-0
52The sleep timer automatically switches the set to standby after the preset time elapses.Sleep Timer1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Timer,then press the OK button.3. Press the Down or Up button to select Sleep Timer,then press the OK button.4. Press the Down or Up button to select desired sleeptime, then press the OK button.The timer begins to count down from the number ofminutes selected.5. Press the MENU button to return to the previousmenu.TimerMove SelectOK CloseMenuFF GGDDEEClockTimerSleep Timer OffTimerMove SelectOK CloseMenuFF GGDDEEClockTimerSleep Timer OffOff10 min30 min60 min90 min-If you want to select Sleep Timer directly, press the SLEEP button.-Every time you press the button, it will switch between Off,10, 30, 60, 90 and 120.NNNNOOOOTTTTEEEETime Setting
53Option MenusOther languages may be available if a digital signal is provided by the broadcasting station.Audio Language1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Option,then press the OK button.3. Press the Down or Up button to select AudioLanguage, then press the OK button.4. Press the Down or Up button to select your desiredlanguage and then press the OK button.(Select between English, French, Spanish, German,Korean, Chinese, Japanese)5. Press the MENU button to return to the previous menu.Option MenusOptionMenu LanguageAudio LanguageInput LabelCaptionPC SettingPIP SettingMenu OpacityEnglishEnglishMediumMove SelectOK CloseMenuFFGGDDEEOptionMenu LanguageAudio LanguageInput LabelCaptionPC SettingPIP SettingMenu OpacityEnglishEnglishMediumMove SelectOK CloseMenuFFGGDDEEEnglishFrenchSpanishGermanKorean
54Sets a label to each input source which is not in use when you press SOURCE button.Input Label1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Option,then press the OK button.3. Press the Down or Up button to select Input Label,then press the OK button.4. Press the Down or Up button to select the input sourceto rename, then press the OK button. 5. Press the Down button to select the predefined nameand then press the OK button.6. Or when you want to directly rename it yourself, pressthe Down or Up or Left or Right button, select thecharacters shown on the screen and press the OKbutton.7. Press the Left or Right button to select OK or Cancel.If you want to confirm the assigned new name, selectOK. Then press the OK button. Otherwise select Cancel.8. Press the MENU button to return to the previous menu.-When you want to enter lower case characters, select the Shift button and then select the character youwant after pressing the OK button-If you want to reset the entered character, select the Reset to Default button and then the OK button.-If you want to delete the entered character, select the BS button and then press the OK button.NNNNOOOOTTTTEEEEInput LabelTunerETVE1234567890A B C D E F G H I JK L M N O P Q R S TU V W X Y Z - BSCancelShiftOKReset to Default_Move SelectOK CloseMenuFF GGDDEEOptionMenu LanguageAudio LanguageInput LabelCaptionPC SettingPIP SettingMenu OpacityEnglishEnglishMediumMove SelectOK CloseMenuFFGGDDEEOption Menus
55Option MenusCaption must be provided to help people with hearing loss watch TV.Caption Mode1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Option,then press the OK button.3. Press the Down or Up button to select Caption, thenpress the OK button.4. Press the Down or Up button to select Display, thenpress the OK button.5. Press the Down or Up button to select On or Off, thenpress the OK button.6. Press the MENU button to return to the previous menu.Option > CaptionMove SelectOK Go BackMenuFF GGDDEEDisplayBasic SelectionAdvanced SelectionAdvanced AppearanceOnCS1OffOnOptionMenu LanguageAudio LanguageInput LabelCaptionPC SettingPIP SettingMenu OpacityEnglishEnglishMediumMove SelectOK CloseMenuFFGGDDEE-If you want to select Caption directly, press the CC button.NNNNOOOOTTTTEEEE
56The Analog Caption function operates when watching regular analog channels.Analog caption displays information at any position on the screen and is usually the program’s dialog.Closed Caption-Analog1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Option,then press the OK button.3. Press the Down or Up button to select Caption, thenpress the OK button.4. Press the Down or Up button to select BasicSelection, then press the OK button.5. Press the Down or Up button repeatedly to select CC1,CC2, CC3,CC4,Text1,Text2, Text3 or Text4, thenpress the OK button.6. Press the MENU button to return to the previous menu.CaptionThe term for the words that scroll across the bottom ofthe TV screen; usually the audio portion of the pro-gram provided for the hearing impaired.TEXTThe term for the words that appear in a large blackframe and almost cover the entire screen; usually mes-sages provided by the broadcaster.-If you want to select Caption directly, press the CC button.NNNNOOOOTTTTEEEEOption > CaptionMove SelectOK Go BackMenuFF GGDDEEDisplayBasic SelectionAdvanced SelectionAdvanced AppearanceOnCC1CC1CC2CC3CC4Text1OptionMenu LanguageAudio LanguageInput LabelCaptionPC SettingPIP SettingMenu OpacityEnglishEnglishMediumMove SelectOK CloseMenuFFGGDDEEOption Menus
57Option MenusThe Digital Caption function only operates on digital channels.Choose the language you want the DTV captions to appear in.Closed Caption-Digital1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Option,then press the OK button.3. Press the Down or Up button to select Caption, thenpress the OK button.4. Press the Down or Up button to select AdvancedSelection, then press the OK button.5. Press the Down or Up button repeatedly to select CS1,CS2, CS3,CS4,CS5 or CS6, then press the OKbutton.6. Press the MENU button to return to the previous menu.Option > CaptionMove SelectOK Go BackMenuFF GGDDEEDisplayBasic SelectionAdvanced SelectionAdvanced AppearanceOnCC1CS1CS1CS2CS3CS4CS5OptionMenu LanguageAudio LanguageInput LabelCaptionPC SettingPIP SettingMenu OpacityEnglishEnglishMediumMove SelectOK CloseMenuFFGGDDEE
58Customize the DTV captions that appear on your screen.Closed Caption OptionsOption > CaptionMove SelectOK Go BackMenuFF GGDDEEDisplayBasic SelectionAdvanced SelectionAdvanced AppearanceOnCC1CS1Advanced AppearanceMove SelectOK CloseMenuFF GGDDEEFont Style As BroadcastEText Size StandardEColor DefaultEdge Color DefaultBackground Color DefaultFrame Color DefaultReset to Default OKAlign StandardEOpacity As BroadcastEStyle As BroadcastEOpacity As BroadcastEOpacity As BroadcastEStorybookCursiveCasualFormalAs Bradcast1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Option,then press the OK button.3. Press the Down or Up button to select Caption, thenpress the OK button.4. Press the Down or Up button to select AdvancedAppearance, then press the OK button.5. Press the Down or Up or Left or Right button to selectdesired caption option. (Font Style, Text Size, Align, Color, Color Opacity,Edge Color, Edge Color Style, Background Color,Background Color Opacity, Frame Color, FrameColor Opacity)6. Press the Down or Up button and then press the OKbutton to customize your preference. 7. To complete the setting, press the Down or Up or Left or Right button, select OK button and thenpress the OK button.8. Press the MENU button to return to the previous menu.-If caption options are selected to As Broadcast, Caption Options are cannot be adjusted.-If you select the Reset to Default, reset all the caption options to their original factory preset values.NNNNOOOOTTTTEEEEOptionMenu LanguageAudio LanguageInput LabelCaptionPC SettingPIP SettingMenu OpacityEnglishEnglishMediumMove SelectOK CloseMenuFFGGDDEEOption Menus
59Option MenusFont StyleSelect a typeface for the words.Text SizeSet the size the words will appear in.Text AlignSelect a align for the words.Text ColorChoose a color for the text.Text OpacitySelect the opacity for the text color.Edge ColorSelect a color for the edges.Edge StyleSelect an edge type.Background ColorSelect a background color.Background OpacitySelect the opacity for the background color.Frame ColorSelect a color for the frame.Frame OpacitySelect the opacity for the frame.
60You can set the transparency of the menu box.Menu Opacity1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Option,then press the OK button.3. Press the Down or Up button to select Menu Opacity,then press the OK button.4. Press the Down or Up button to select Low,Mediumor High, then press the OK button.5. Press the MENU button to return to the previous menu.OptionMove SelectOK CloseMenuFF GGDDEEMenu LanguageAudio LanguageInput LabelCaptionPC SettingPIP SettingMenu OpacityEnglishEnglishMediumLowMediumHighOptionMenu LanguageAudio LanguageInput LabelCaptionPC SettingPIP SettingMenu OpacityEnglishEnglishMediumMove SelectOK CloseMenuFFGGDDEEOption Menus
61Parental ControlParental Control can be used to block specific channels, ratings and other viewing sources.Set up blocking schemes to block specific channels, ratings, and external viewing sources.Apassword is required to gain access to this menu.Enter your password1. Press the MENU button to display the menu.2. Press the Down or Up buttons to select the Lock, thenpress the OK button.3. Enter password as requested.The TV is set up with the initial password “0-0-0-0”.Enables or disables the blocking scheme you set up previously.Lock System1. After inputting the password, press the Down or Upbutton to choose Lock System.2. Press the OK button to select On or Off.When you select On, the Lock menus are enable.3. Press the MENU button to return to the previous menu.- When Lock System is On, you cannot use the PIP function.NNNNOOOOTTTTEEEEParental ControlLockMove SelectOK CloseMenuFF GGDDEELock SystemSet PasswordBlock ChannelRatingOffEnter Password* * *LockMove SelectOK CloseMenuFF GGDDEELock SystemSet PasswordBlock ChannelRatingOff
62Change the password by inputting a new password twice.Set Password1. After inputting the password, press the Down or Upbutton to select Set Password.2. Press the OK button and then re-enter the same 4 dig-its.3. Select any 4 digits for your new password and enterthe them on the New.4. As soon as the 4 digits are entered, re-enter the same4 digits on the Confirm.5. Press the Left or Right button to select OK, then pressthe OK button.Then your changed password has been memorized.6. Press the MENU button to return to the previous menu.LockMove SelectOK CloseMenuFF GGDDEELock SystemSet PasswordBlock ChannelRatingOffEnter Password* * *Set Password***New :Confirm :OK CancelParental Control
63Parental ControlBlocks any channels that you do not want to watch or that you do not want your children to watch.Channel Blocking1. After inputting the password, press the Down or Upbutton to choose Block Channel.Then display a list of all channels.2. Press the Down or Up button to select a channel andthen press the OK button to block or unblock it.3. Press the MENU button to return to the previous menu.LockMove SelectOK CloseMenuFF GGDDEELock SystemSet PasswordBlock ChannelRatingOffBlock ChannelMoveCloseMenuDDEEToggle LockOKMove PageCH DDEE9-010-011-012-013-0
64Prevents children from watching certain TV programs, according to the rating limits set.The children rating will not apply to TV programs until you select the ratings you want to be blocked.TV Ratings for USA1. After inputting the password, press the Down or Upbutton to choose Rating.2. Press the OK button and then press the Down or Upbutton to select USA - TV.3. Press the OK button.4. Press the Down or Up or Left or Right buttons tochoose and OK button to set up the menu options forUSA TV Ratings.5. Press the Left or Right or Down or Up button to selectOK, then press the OK button.6. Press the MENU button to return to the previous menu.LockMove SelectOK CloseMenuFF GGDDEELock SystemSet PasswordBlock ChannelRatingOffLock > RatingMove SelectOK Go BackMenuFF GGDDEEUSA - TVUSA - MovieCanada - EnglishCanada - FrenchDownloadable RRTUSA - TVTV-YTV-Y7TV-GTV-PGTV-14TV-MAFV D L S VMove SelectOK CloseMenuFF GGDDEELock AllUnlock All OK-When you select Lock All, all options will be locked and when you select Unlock All, all options will beunlocked.NNNNOOOOTTTTEEEEParental Control
65Parental ControlTV (FCC) Age CategoriesD: Dialog...sexual innuendo.L: Offensive language.S: Sexual SituationV: Violence.FV: Fantasy or cartoon violence.TV (FCC) Content Sub-Categories:TV-MAMature audiences only.This program may contain mature themes,profane language, graphic violence and explicitsexual content.TV-14Parents strongly cautioned.This program may contain sophisticated themes,sexual content, strong language and more intenseviolence.TV-PGParental guidance suggested.The program may contain infrequent coarselanguage, limited violence, some suggestivesexual dialog and situations.TV-GGeneral audience.This contains little or no violence, no stronglanguage, and little or no sexual dialog orsituations.TV-Y7Directed for older children.Themes and elements in this program mayinclude mild physical or comedic violence, ormay frighten children under the age of seven.TV-YAll children.The themes and elements in this program arespecifically designed for a very young audience,including children from ages two – six.
66Blocks movies according to the movie ratings limits specified so children cannot view certain movies.Applies to movies broadcasted on TV and allows you to select which ratings you want blocked.Movie Ratings1. After inputting the password, press the Down or Upbutton to choose Rating.2. Press the OK button and then press the Down or Upbutton to select USA - Movie.3. Press the OK button.4. Press the Down or Up buttons to choose and OK but-ton to set up the menu options for USA Movie Ratings.5. Press the Down or Up button to select OK, then pressthe OK button.6. Press the MENU button to return to the previous menu.The MPAA Rating System (Movies)G General Audience.PGParental guidance suggested.PG-13Parents strongly cautioned.RRestricted.NC-17No one 17 and under admitted.XAdults only.LockMove SelectOK CloseMenuFF GGDDEELock SystemSet PasswordBlock ChannelRatingOffLock > RatingMove SelectOK Go BackMenuFF GGDDEEUSA - TVUSA - MovieCanada - EnglishCanada - FrenchDownloadable RRTUSA - MovieGPGPG-13RNC-17XMove SelectOK CloseMenuDDEEOK-If you set PG-13 : G and PG movies will be available, PG-13, R, NC-17 and X will be blocked.NNNNOOOOTTTTEEEEParental Control
67Parental ControlSelecting canadian english language rating system.TV Rating English for Canada1. After inputting the password, press the Down or Upbutton to choose Rating.2. Press the OK button and then press the Down or Upbutton to select Canada - English.3. Press the OK button.4. Press the Down or Up buttons to choose and OK but-ton to set up the menu options for Canadian EnglishRatings.5. Press the Down or Up button to select OK, then pressthe OK button.6. Press the MENU button to return to the previous menu.Canadian English RatingsCChildrenC8+Children eight years and olderGGeneral programming, suitable for all audiencesPGParental Guidance 14+Viewers 14 years and older18+Adult programmingLockMove SelectOK CloseMenuFF GGDDEELock SystemSet PasswordBlock ChannelRatingOffLock > RatingMove SelectOK Go BackMenuFF GGDDEEUSA - TVUSA - MovieCanada - EnglishCanada - FrenchDownloadable RRTCanada - EnglishCC8+GPG14+18+Move SelectOK CloseMenuDDEEOK
68Selecting canadian french language rating system.TV Rating French for Canada1. After inputting the password, press the Down or Upbutton to choose Rating.2. Press the OK button and then press the Down or Upbutton to select Canada - French.3. Press the OK button.4. Press the Down or Up buttons to choose and OK but-ton to set up the menu options for Canadian FrenchRatings.5. Press the Down or Up button to select OK, then pressthe OK button.6. Press the MENU button to return to the previous menu.Canadian French RatingsGGeneral8 ans+General-Not convenient for little children13 ans+Not convenient for children of 13 years and younger16 ans+Not convenient for children of 16 years and younger18 ans+This programs is only for adultLockMove SelectOK CloseMenuFF GGDDEELock SystemSet PasswordBlock ChannelRatingOffLock > RatingMove SelectOK Go BackMenuFF GGDDEEUSA - TVUSA - MovieCanada - EnglishCanada - FrenchDownloadable RRTCanada - FrenchG8 ans+13 ans+16 ans+18 ans+Move SelectOK CloseMenuDDEEOKParental Control
81SpecificationBroadcast Signal SystemContrast RatioBrightnessPower RatingConsumptionAudio OutputOperating TemperatureAccessoriesExternal PortWeight(kg / lbs)Model1241.0 mm (48.86") x 841.0 mm (33.11") x 399.0 mm (15.71")1241.0 mm (48.86") x 900.0 mm (35.43") x 774.0 mm (30.47")45.0 kg (99.20 lbs)50.3 kg (110.89 lbs)ATSC / NTSC30,000:11,500 cd/m2AC100-240V ~50/60Hz430W10W + 10W0°C ~ 40°CKPP-50SAT•3 x HDMI•RGB IN (PC)•AUDIO IN (RGB / DVI)•AV IN•S-VIDEO•COMPONENT 1•COMPONENT 2•USB IN•DIGITAL AUDIO OUT(OPTICAL)•ANTENNA / CABLE IN•AC IN• SERVICE• The Specification shown above may be changed without prior notice for quality important.Dimension(Width x Hight x Depth)Without StandWith StandWithout StandWith Stand•Batteries & Remote •Power Cord •Owner’s Manual•Plug Adaptor(UL to VDE)Specification
82TroubleshootingTroubleshootingNo picture on screen.The remote control doesn’t work.Picture appears slowly, afterswitching on.No or Poor colorHorizontal/Vertical bars or pictureshaking Unusual sound from inside the set.Problem Solution•Check whether the set is turned on.•Make sure the power cord is plugged into the wall.•Test if there is power coming from the wall outlet byplugging in another product into the same wall outletwhere the set’s power cord was plugged in.•Check to see if there is any object between the set andthe remote control causing obstruction.•Check to see if the batteries are installed with the correct polarities.•Install new batteries.•This is normal as the image is muted during the start upprocess of the set. Please contact your service center, ifthe picture has not appeared after five minutes.•Select color in the Picture menu and press the Left orRight button.•Check for local interference such as a nearby electricalappliance or power tool.•Achange in ambient humidity or temperature may resultin an unusual noise at the time of switching off or on ofthe set and does not indicate a fault with the set.
P/NO : 3350GDKM0094AGPN09MA001Z

Navigation menu