KINGTA TECHNOLOGY F2 Bluetooth Speaker User Manual

KINGTA TECHNOLOGY CO., LTD Bluetooth Speaker Users Manual

Users Manual

Waterproof Wireless SpeakerUser’s Manual TY-WSP200IntroductionThank you for choosing the TY-WSP200 as your source forentertainment, you can use this item with iPads,iPhones,iPods and many types of smart-phone to stream music ,and enjoy hands-free calling.In order to get the best resultswhen using the device,please read this manual first before using.Included:1.Speaker2.USB Micro Charging Cable3.3.5 mm Micro-USB Cable4.User ManualSpecificationsSupported Profiles:A2DPV1.2 ,AVRCPV1.4,HFPV1.5,HSP1.2,GAVDP1.2Bluetooth Range:33ft (10m)Dimensions: 209*80*81 mmBattery: Li-Ion 3.7V/2000mAhCharging: 5V @ 1 AFeartures-Volume and song control directly on speaker unit-Stunning sound clarity-Ultra portable design-Great for parties, indoor and outdoor-Allow you to make and answer phone calls1.Previous / Volume –2.ON/OFF button3.Next / Volume +4.Green LED(AUX)5.Red LED(Charging)6.Blue LED(Bluetooth)7.Phone /play button8.MIC9.Micro USB Charging/AUX in Port1 28934567
OperationPowering OnPress and Hold "ON/OFF" button 2 seconds to power ON, theBlue LED will start to flash.If an AUX (3.5 mm) cable is connected to the unit, the Blue LED will turn off , and the Green LED will stay illuminated,notifying you the unit is in Aux-In mode.Powering OffPress and Hold "ON/OFF" button 2 seconds to power OFFAux-In ModePlug in the supplied 3.5 mm cable into the unit. The other end isconnected to your device. The Green LED will stay illminated .It means in “Aux” mode.Please note music and volume can be controlled by your device.ChargingAttach the USB cable to the unit, and plug into any USB charger.If the unit is completely discharged, it will take approximately 4hours to fully charge.The Red LED will illuminate during charging, when it hascompleted, the Red LED will turn off.Note:There will be a beep when the battery is low and needs tobe recharged.Bluetooth ModePairingThe unit will automatically go into “Pairing Mode” when it ispowered ON.Go into your Bluetooth device settings menu and look for “TY-WSP200” After the unit has paired and connected, it will re-connect automatically when the unit is powered on and the device is in range.Note: Bluetooth Timeout :10 minutesMaking and Receiving Phone CallsWhen the unit is connected and paired to your device,the unit allows you to make or receive phone calls with itsbuilt-in microphone.Press “ ” to accept a callTo end a call press“ ”To place a call, simply dial the number or select a contact formTo reject a call, press and hold “ ” for 2 secondsBegin Streaming MusicPress “ ” to start playing music.Press and Hold “ ” 2 seconds to play the next track.Press and Hold “ ” 2 seconds to play the previous track.Press either “ ” or “ ” for volume control. LED StatusBlue LED solid Bluetooth ModeGreen LED on solidRed LEDAux ModeChargingTroubleshootingUnit doesn’t connect to deviceSpeaker needs to be connected/re-paired to device A tone is heard every few seconds Speaker needs to be chargedUnit will not power on Speaker needs to be chargedUnit doesn’t controltrack(s)/volumeSpeaker needs to be in Bluetoothmode for full controlUnit distorts athigh volume The devices’ volume needs tobe lowered
FCC Caution. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Navigation menu