KINGTA TECHNOLOGY S6 Bluetooth Speaker User Manual
KINGTA TECHNOLOGY CO., LTD Bluetooth Speaker Users Manual
Users Manual
Bluetooth Speaker User’s Manual Description
Introduction
Thank you for choosing the S6 Speaker as your source
for entertainment. You can use this item with iPad, iPhone,
iPod and many types of smart-phone to stream music
and enjoy hands-free calling. For the best results,
please read this manual before using the speaker.
Include
1. Speaker
2. 3.5 mm Audio Cable
3. User Manual
Specification
BluetoothRange：33ft（10M）
TWSdistance：11.5ft（5M）
Dimensions:236mmx59.5mmx102.8mm
BTVersion：4.2
Output：2x10W
Speaker/driversize：57mm4Ω 10W
Battery:7.4V 2400mAh 3C
Charging:4 H
Important Safety Information
1.Keep this product and its charging cable away from
excessive heat;
2.Do not operate this device with a damaged cable
or after it has malfunctioned or has been damaged
in any manner;
3.Do not disassemble your device;
S6
1.ON / OFF
2.Next Music/Volume
3.Pause/Phone
4.Previous Music/Volume
5.Bluetooth LED
6.Micro USB Charging Port
7.AUX in Port
FCC ID: N7KS6
Model Name: S6
Power on
Press and Hold “ ” button 2 seconds to power ON.
Power off
Press and Hold “ ” button 2 seconds to power OFF.
Operation
Pairing
The unit will automatically go into “Pairing Mode” when it is
powered ON.
Go into your Bluetooth device settings menu and look for
“S6”.
After the unit has been paired and connected, it will
re-connect automatically when the unit is powered on and
the device is in range.
Press and hold” ”2 seconds bluetooth will be disconnected
Note: Bluetooth Timeout :10 minutes.
Bluetooth Mode
Begin Streaming Music
Press “ ” to start playing music.
Press and Hold “ ” 2 seconds to play the next track.
Press and Hold “ ” 2 seconds to play the previous track.
Press either “ ” or “ ” for volume control.
Hands-Free Function
When the unit is connected and paired to your device, you
can use the hands-free function with its built-in microphone.
Press “ ” to accept a call.
To end a call press “ ”.
Aux-In Mode
Plug in the supplied 3.5 mm audio cable into the unit. The
other end is connected to your device. The unit will
automatically enter the Aux-In mode.
Please note music and volume can be controlled by
your device.
Charging
Attach the USB cable to the unit, and plug into any USB
charger. If the unit is completely discharged, it will take
approximately 4 hours to fully charge.
These three key lights “ ” “ ” “ ” will be breath
lighting when charging, and they will become solid once
fully charged.
Note: There will be a beep when the battery is low and
needs to be recharged.
TWS Wireless Stereo Mode
If you have two pieces S6, you can use TWS function
to achieve wireless stereo combined-playing music.
1.Make sure both S6 are without any Bluetooth
connection.
2.Power on both speakers, and touch each other with the side,
the two speakers will connect automatically with a notifying
tone.
When LED blink on one speaker and keeps solid on
the other one, it means the TWS connection is successful.
3.Then you can search your Bluetooth device and
select “S6”.
4.Touch them again for Bluetooth Disconnection.
5.Press and Hold “ ” button 2 seconds on one of
the units, both units will be powered off.
Unit doesn’t connect
to device
Speaker needs to be connected /
re-paired to device
A tone is heard every
few seconds
Speaker needs to
be recharged
Unit will not power on Speaker needs to
be recharged
Unit doesn’t control
track(s) / volume
Speaker needs to be in Bluetooth
mode for full control
Unit distorts at
high volume
The devices’ volume
needs to be lowered
Troubleshooting
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used
in portable exposure condition without restriction.