KP Electronic Systems KPBSRU100 Non-Broadcast Station TX User Manual users manual

Download:
Mirror Download [FCC.gov]
Document ID	120532
Application ID	7SK+P8Jj3drDa84QYdSVfA==
Document Description	users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	40.61kB (507626 bits)
Date Submitted	2000-10-10 00:00:00
Date Available	2000-10-09 00:00:00
Creation Date	2000-10-03 14:48:38
Producing Software	Photoshop PDF Plug-in 1.0
Document Lastmod	2000-10-03 14:49:09
Document Title	users manual
Document Creator	Photoshop PDF Plug-in 1.0

BSRUIOOTM
5an room has five sets ofconnectors:
Jr, Jz, J3, J4, J5 (see Figure 1).
K ELECTRONIC i m»,
SYSTEMS LTD M
Web Site: www.kpsystems.com
ISRAEL Office
Email: info@kgsystems.com
Tefen Industrial Park. Telen 24959
Tel'97Z-4-987-3066 Fax 97249813692
USA Office:
KP ELECTRONiCS lNC.
Email kgelectron@aol.com
109 Tudor Drlve, North Waies.PA19454
Tel: (215) 542-7460 Fax (215) 542-7451
Book OXX
fluvmw vawudsun 12mm:
BSRU100WI General Description
The BSRUIOOTM UHF transceiver
operates as a two-way base-station radio in
half duplex mode at remote central stations
and repeaters. It is modulated by an FSK
signal.
Functions:
- Receives and transmits:
—FSK (frequency shift keying)
modulated signals
7 DP (direct frequency) modulation
OPerforms receiving and transmitting
frequency programming changes
- RSSI output
- Measurement analog output
- Visual control *
- Channel monitor control
a PTT control
' On/Off indicator
‘See Table 1: Self-Test LED:
UHF Base-Station Radio “Pram Vfislsurino
‘ Transceiver M m T a» my
User Guide
in?
J1 J5 43
Figure]: BSRUIOUTM Connectors
ch: BNC connector connects an Rx UHF
antenna.
OJZ: BNC connector connects an Rx\Tx
UHF antenna.*
ilqpllonali ENC connector connects a Tx antenna,
on y,
-J3: 12.5 VDC power supply
oJ4: A 10-pin contact connector connects:
—+VB
4 GND
— 113232 IN
7 RS232 OUT
— PTT
— AUDIO IN 1,
~ DIAGNOSTIC MODE
fAUDlO OUT " (optional)
tJS: A D~type lS-pin rear panel connector
connects:
APTT
- PTTZ OUT
— R5232 IN
— R5232 OUT
—- GND
vAUDIO OUT
—AUDIO IN
7 CHANNEL MONITOR
— RSSI OUT
~ RSSI TO AI
e DATAOUT
Preparing for Operation
Before installing BSRUIOOTM, perform
the following preparations:
. Setting communication parameters
. Connecting assembly cables and power
supply connector,
0 Self Test
Setting Communication Parameters
(See BSR U1 (7an Programming Guide.)
Connecting Assembly Cables
To Connect the p=50 Ohm Cable:
1. Connect one end ofthe o=50 Ohm
cable to 12, the Rx/Tx BNC
connector.
2. Connect the other end ofthe p:50
Ohm cable to the 50 Ohm load,
according to its application wiring
diagram.
To Connect the DC plug to the J4 DC
Power Connector:
l'. Connect one end of the cable to is,
the D-type lS—pin rear panel
connector. '
2. Connect the other end of the cable,
according to its application wiring
diagram.
Sell Test:
1. Connect the 12.5 VDC power supply
to the DC current wires.
2. Observe the Self—Test LEDs
(see Figure 2).
KP $3355 asnu 100
m m cm PM“
. 0 .
Figure 2; Self-Test LEDs
Table 1: Self-Test L
EDs
LED PTT
ON (red) Tx mode
OFF FE; mode
2 Flashes 0» Overload” i
3 Flashes Predriver/Drlver
1 Flash H" Time out timer
4 Flashes m PLL
4 Flashes Synthesizer
Power LED
Green I Normal
Red ' Dead Battery
CM LED ’
Green Free
3 Red {Channel
g; Monitor
Flashes redl-green _ RFIIF Amplifiers
In addition to the sigma
is an error-status word
Utility Program,
ls in Table 1, there
in the CiuplOTM
KP ELECTRONIC SYSTEMS LTD.
FCC to: H78KPBSRU100
EXHIBIT #: 41
BSRU1 00 ‘M Programming Guide
Using KP’s GuplOTM Utility Program,
the BSRUIOOTM parameter values listed
below can be rogramined or modified.
An RSINTOO ijadaptei' connects
between BSRUIOO and a PC (see
Figure 3).
- Transmit frequency (MHz)
0 Receiver frequency (MHz)
- Tx time out (0-240 sec.)
Figure 3: BSRUIOOW
PC Connection Configuration
Operating Instructions
0 Connecting BSRUIOOTM to GuplOTM
(utility program)
0 Loading Parameter Values
0 Changing Parameter Values
- Updating Parameter Value Changes
- Confirming Parameter Value Changes
0 Activating Self Test
Connecting BSRU100'M to Gup10‘“
1. Connect BSRUlOOTM to a PC using the
RSINTOOI adapter (see Figure 3).
2. Click Start>Programs>
KP Uliliiies>GUP10.
The GUP10 main screen displays,
showing the device type, version, and
suitable defoulrparameters.
Loading Parameter Values
Parameter values must be loaded after
connecting the GuplOTM utility software.
To Load Parameter Values
1, From the Gup10 main screen, click
Prompt ? (Alt P). i)
2. Click Read (Alt R). The name of the
device type, version, and suitable
parameters are displayed. ‘
Changing Parameter Values
Parameter values can be changed, as required:
a Type the new parameter value in the
designated parameter text box.
Technical Specifications:
Operating Frequent: 450-470 MI-Iz
Space Channel 12 5 kHz
Nominal Operating 12 5 VDC
Voltage
Standby Current lZOmA max.
TX Current 2.4A max.
Nominal Power Output 10W
FrequencyStability 12.5ppm
(at operating temp.
ran e)
Sensitivity -l 17 DBm
(l2 Db sinad)
Adjustment Channel 58 DB
Selectivtiy
Operating Temp, -23°F . 141°F
(40°C ~ 60°C)
Storage Temp. 40°F ~ 158°P
(-20°C - 70°C)
Weight 1.44 lbs. (655 gr.)
I'on the middle frequency ofthe working band
Updating Parameter Value Changes
1. Click Send (Alt S).
The Send Warning dialog box displays
“Are you sure?”
2, Choose one:
- Click Yes, to update parameter changes.
OR
a Click No, to return to the GuplO main
screen without updating changes.
Confirming Parameter Changes
Ensure that any parameter value changes
made are updated.
To Confirm Parameter Changes
From the Cup“) main screen, click Read
(Alt R).
The Gup10 main screen displays the
updated parameter values.
Troubleshooting
See Figure 4 for diagnostic results
Performing SELF TEST
After parameter values are loaded, perform
SELF TEST:
1. Disconnect BSRUlOO"'M from the PC.
2, Press the Self-Test button.
3. Observe the Self-Test LED.
(Refer to Table 2 for SELF - TES T
results.)
On-Screen HELP
To view a brief explanation of any
BSRUIOOTM parameter, click the
reouired parameter text box. The cursor
wi 1 appear in the designated text box,
and the valid parameter range, with a
brief explanation, displays at the bottom
of the screen.
KP ELECTRONIC SYSTEMS LTD.
FCC ID' H78KPBSRUIOO
EXHIBIT #.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Modify Date                     : 2000:10:03 14:49:09
Creator                         : Photoshop PDF Plug-in 1.0
Producer                        : Photoshop PDF Plug-in 1.0
Create Date                     : 2000:10:03 14:48:38
Page Count                      : 2

EXIF Metadata provided by EXIF.tools