KYE SYSTEMS GMZHD TRAVELER 1000 User Manual Ergo3000 eng vp CorelVentura 7 0

KYE Systems Corp TRAVELER 1000 Ergo3000 eng vp CorelVentura 7 0

users manual

Hardware Installation1. You can connect the receiver to a USB port of a PC2. Install one AA battery in the mouse.3. Turn on your computer.4. After you open Windows, please press the button on the receiver first and thenpress the button under the mouse for channel setting.Important: Remember do not put the batteries in the wrong direction, use the sametypes of batteries. Also, keep all drinks away! If any spill occurs on the receiver,unplug the USB connector first and clean the receiver immediately. Please switch thebutton to "off" under the mouse once you don't use it for a long time, and remove thebatteries if you do not use this device for at least two weeks.Warning: (Troubleshooting)1. Please do not use Wireless optical mouse on a desk which is made of glass, mir-ror, iron, or black velvet. Also, a flat surface is necessary or the Optical Sensorwill error easily. When you use Wireless optical mouse on a desk that is made ofmetal, try using a pad and reduce the receiving distance.1ENGLISH
2. Before the first installation is completed (channel setting ready), the mouse willnot work in DOS.3. The Wireless optical mouse channel provides 256 ID-codes, and it automaticallyselects the ID # for your mouse. You can only set up one Wireless optical mouseat a time. But if you have additional Wireless optical mouse sets in an area of 10square meters, more interference will occur between the receiver and yourmouse.4. If you feel the mouse does not move smooth as usual, then the batteries have losttheir charge, so please replace them.5. The Wireless optical mouse with radio frequency gives you free movement andan enjoyable experience. For optimal performance, place the receiver at least 8inches (about 20 cm) away from the mouse and other electrical devices, such asthe computer, monitor, and etc.Software Installation1. Make sure the mouse is connected to the computer.2. Put the Setup disk (or CD) into the disk drive.3. Follow the instructions on the screen to finish the software installation.Factory Setting2
Button AssignmentsThe Button Assignment feature lets you work in a moreefficient way because you can assign the most fre-quently used commands in Windows to the mouse but-tons.Magic-Roller Press the “Magic-Roller” to surf theInternet and Windows documentsHorizontalScrollPress the roller to the left and the cursorscrolls to the left; press the roller to theright and the cursor scrolls to the right.Left Button Provides traditional mouse functionssuch as click, double click and drag.Right Button You can assign this button frequently used keyboard and mouse func-tions in addition to features like EasyJump, Auto-Panning, Zoom, etc.Roller ButtonYou can assign this button frequently used keyboard and mouse func-tions in addition to features like EasyJump, Auto-Panning, Zoom, etc.3
FCC Compliance and Advisory Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. The equipment has been certified to comply with the limits for a Class B computing device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed or used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by switching the equipment off and on. The user can try to correct the interference by the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or and experience radio/TV technician for help. Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Navigation menu