KYE SYSTEMS GMZHH WIRELESS MOUSE User Manual R815 eng vp CorelVentura 7 0

KYE Systems Corp WIRELESS MOUSE R815 eng vp CorelVentura 7 0

USERS MANUAL

FCC ID: FSUGMZHH FCC Compliance and Advisory Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures: 1.Reorient the receiving antenna. 2.Increase the separation between the equipment and receiver. 3.Connect the equipment into and outlet on a circuit different from that to which the receiver is connected. 4.Consult the dealer or an experienced radio/TV technician for help. Any special accessories needed for compliance must be specified in the instruction manual. Warning: A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment. CAUSION: Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
Hardware Installation1. You can connect the receiver to a USB port of a PC or Notebook.2. If you want to connect the receiver to a PC orrecharge the batteries, please use the USB bat-tery charger cable. (Please do not connect thereceiver directly to a PC that is placed undera table, or the RF performance will decreasedramatically.)3. Install two AA rechargeable batteries in themouse. (Use only rechargeable batteries. Us-ing any other type of battery could cause seri-ous damage to your mouse or mainboard). Donot charge batteries unless there are otherbatteries in the mouse. Otherwise, you cannot use the mouse if you arecharging the batteries.4. Turn on your computer.5. After you open Windows, press the button on the receiver first, then press thebutton under the mouse for channel setting.1ENGLISH
Important: When you use this product for the first time, the mouse may seem to besluggish because it takes between 12 to 16 hours of use for the batteries to berecharged to obtain full performance. The other alternative is to recharge the bat-teries before you use the Wireless laser mouse device. Please remove the batteriesif you do not use this device for at least two weeks.Warning: (Troubleshooting)1. Please do not use the Wireless laser mouse on a desk which is made of glass ormirror.2. Before the first installation is completed (channel setting ready), the mouse willnot work.3. The Wireless laser mouse channel provides 256 ID-codes, and it automaticallyselects the ID # for your mouse. You can only set up one Wireless laser mouseat a time. But if you have additional Wireless laser mouse sets in an area of 10square meters, more interference will occur between the receiver and yourmouse.4. If you feel the mouse does not move as smooth as usual, then the batteries havelost their charge, so you need to replace them or use the USB battery chargercable to recharge the batteries. The LED on the mouse shows thebattery-recharging status: it will shine when empty and be clear when thebatteries are recharged. You should set up the channel every time you replacethe batteries.5. If you need to buy new batteries, please choose Ni-MH (Nickel-Metal-Hydride)AA batteries, 1300 to 1500 mAH, 1.2 V. Please do not mix or use other typesof batteries (Li-ion, Ni-Cd, Alkaline, etc.). Recycle your batteries accordingto local law.6. The Wireless laser mouse with radio frequency gives you free movement and anenjoyable experience. For optimal performance, place the receiver at least 8inches (about 20 cm) away from the mouse and other electrical devices, such asthe computer, monitor, and etc.Software Installation1. Make sure the mouse is connected to the computer.2. Put the Setup disk (or CD) into the disk drive.3. Follow the instructions on the screen to finish the software installation.2
Factory SettingButton Assignments1. Left Button: Provides traditionalmouse functions such as click, dou-ble click and drag.2. Right Button: You can assign thisbutton frequently used keyboard andmouse functions in addition to fea-tures like EasyJump, Auto-Panning,Zoom, etc.3. Magic-Roller: Press the “Magic-Roller” to surf the Internet and Win-dows documents.Horizontal Scroll: Press the rollerto the left and the cursor scrolls to the left; press the roller to the rightand the cursor scrolls to the right.4. Previous: See previous song when viewing the media Player.5. Next: Go to next song when viewing the media player.6. Vol. +: Increase volume7. Vol. -: Decrease volume8. Sensitivity: Sensitivity Adjustment (This button only for sensitivity ad-justment, it is not programmable).3ENGLISH

Navigation menu