KYE SYSTEMS GMZJO WIRELESS MOUSE DX-ECO(GM-110013/T,GM-110003/T) User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1521434
Application ID	gMrb8UNXHilAKtVarur+5g==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	6.59kB (82349 bits)
Date Submitted	2011-08-11 00:00:00
Date Available	2011-08-11 00:00:00
Creation Date	2011-08-04 18:44:42
Producing Software	GPL Ghostscript 8.64
Document Lastmod	2011-08-04 18:44:42
Document Title	Microsoft Word - 4.USER MANUAL & 6.OPERATIONAL DESCRIPTION.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	XP

English
Hardware Installation
Note: Supports Windows 7/Vista/XP
1. Connect the Micro USB charging cable to the mouse and any PC USB port.
2. You can connect the receiver to a USB port of a PC.
3. In charging mode, the RED LED light will be on and off when charged.
4. Make sure that you have switched on the power switch underneath the mouse.
Remark:
It takes around five minutes to charge up the capacitor and you can use the mouse for about
four hours. Actual performance varies according to the conditions.
Software Installation
1. Place CD into CD/DVD-Rom drive.
2. Follow the instruction on the screen to complete software setup.
3. Restart your PC.
Factory Settings
1. Previous Page: Go to last page of Internet Explorer
2. Next Page: Go to last page of Internet Explorer
3. Left Button: Provides traditional mouse functions like click, double click and drag.
4. Magic-Roller: Press the “Magic-Roller” to surf the Internet and Windows documents.
5. Right Button: Provides traditional mouse click functions.
6. DPI adjustment: Default is 1600 dpi, press once for 800 dpi. Quick red flashing is 1600 dpi
and slow red flashing is 800 dpi.
7. Flying Scroll: Press and hold to move vertically or horizontally for 4-way scrolling.
Capacitor low indication
If the LED is flashing, then the capacitor level is low, you need to recharge the mouse
immediately.
Warning: (Troubleshooting)
1. Do not use the wireless optical/laser mouse on a desk which is made of glass or mirror.
2. The connection of the wireless device is factory preset, so when you plug the USB receiver
into any USB port, the connection between the micro receiver and the mouse will be
established automatically.
3. In case your PC did not install the hardware successfully, remove the micro receiver from
the USB port and go Human Interface Devices under Device Manager to remove the
mouse then plug in the micro receiver to a USB port again.
4. If you feel the mouse does not move smooth as usual, it is possible the batteries have lost
their charge so you need to replace them. Remember to put the batteries in the correct
direction.
5. Keep the mouse away from heat in order to prevent damage to the capacitor.
English
FCC ID: FSUGMZJO
FCC Compliance and Advisory Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:(1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device,
according to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try correct the interference by one or more
of the following measures:
1.Reorient the receiving antenna.
2.Increase the separation between the equipment and receiver.
3.Connect the equipment into and outlet on a circuit different from that to which the receiver is
connected.
4.Consult the dealer or an experienced radio/TV technician for help.
Any special accessories needed for compliance must be specified in the instruction manual.
Warning: A shielded-type power cord is required in order to meet FCC emission limits and
also to prevent interference to the nearby radio and television reception. It is essential that
only the supplied power cord be used. Use only shielded cables to connect I/O devices to this
equipment.
CAUSION: Any changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
IC statementThis Class B digital apparatus complies with Canadian ICES-003.Cet
appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 2
Producer                        : GPL Ghostscript 8.64
Create Date                     : 2011:08:04 18:44:42+08:00
Modify Date                     : 2011:08:04 18:44:42+08:00
Title                           : Microsoft Word - 4.USER MANUAL & 6.OPERATIONAL DESCRIPTION.doc
Creator                         : PScript5.dll Version 5.2
Author                          : XP

EXIF Metadata provided by EXIF.tools