KYE SYSTEMS GMZKZ 2.4GHz Wireless Mouse User Manual Hardware Installation

Download:
Mirror Download [FCC.gov]
Document ID	2028219
Application ID	Jt72ygYbML3JJvfMU683oA==
Document Description	FSUGMZKZ User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.87kB (260858 bits)
Date Submitted	2013-07-30 00:00:00
Date Available	2013-07-30 00:00:00
Creation Date	2013-07-22 17:16:10
Producing Software	Adobe Acrobat 8.0
Document Lastmod	2013-07-22 17:16:10
Document Title	Hardware Installation
Document Creator	Adobe Acrobat 8.0 Combine Files
Document Author:	11003218

English
Getting Started:
1. Before you can use this device, it needs to be charged, so connect the micro USB
cable to Micro Traveler 9000R and any USB port on your PC. It takes
approximately two until three hours to fully charge.
2. In charging mode, the LED light will be on and will turn off when charged.
3. Connect the USB receiver to any USB port on your PC.
4. Make sure that you have switched on the power switch underneath the mouse.
Note: If the LED is flashing, you need to recharge the mouse immediately.
Mouse Button Assignments
1. Left Button: Provides traditional mouse functions
like click, double click and drag.
2. Magic-Roller: Press the “Magic-Roller” to surf the
Internet and Windows documents.
3. Right Button: Provides traditional mouse click
functions.
4. LED indicator: Indicates device
Starting/Charging/Battery low
- Starting: LED lights up for three seconds to
initiate.
- Charging: LED light is ON.
- Fully charged: LED light is OFF.
- Battery low: LED will flash at a slow speed to indicate low battery power.
Note: Download the programmable driver from our website: www.geniusnet.com
Warning: (Troubleshooting)
1. Do not use the wireless optical/laser mouse on a desk which is made of glass or
mirror.
2. The connection of the wireless device is factory preset, so when you plug the
USB receiver into any USB port, the connection between the micro receiver and
the mouse will be established automatically.
3. In case your PC did not install the hardware successfully, remove the micro
receiver from the USB port and go Human Interface Devices under Device
Manager to remove the mouse then plug in the micro receiver to a USB port
again.
4. If you feel the mouse does not move smooth as usual, you need to recharge the
mouse immediately.
English
Note: Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment. (15.21)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.(15.19(a)(3))
FEDERAL COMMUNICATIONS COMMISSION
INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2013:07:22 17:16:10+08:00
Create Date                     : 2013:07:22 17:16:10+08:00
Metadata Date                   : 2013:07:22 17:16:10+08:00
Creator Tool                    : Adobe Acrobat 8.0 Combine Files
Format                          : application/pdf
Title                           : Hardware Installation
Creator                         : 11003218
Document ID                     : uuid:b9eda078-82c0-4192-b53e-39f1d96d9189
Instance ID                     : uuid:df729d20-37fb-4536-9d8a-16fd645ca27d
Producer                        : Adobe Acrobat 8.0
Has XFA                         : No
Page Count                      : 2
Author                          : 11003218

EXIF Metadata provided by EXIF.tools