Kaba Access Operations Manual Lock Command Options With Descriptions E Plex/Power Plex 2000 Series Powerplex Quick Reference Guide Pkg3172
E-Plex/PowerPlex 2000 Series Quick Reference Guide - PKG3172 e-plex-powerplex-2000-series-quick-reference-guide-pkg3172 E-Plex 2000 Electronic Pushbutton Lock - Kaba Access & Data Systems
Lock Command Options with Descriptions - E-Plex/PowerPlex 2000 Series e-plex-powerplex-2000-series-quick-reference-guide-pkg3172 Product Guide
User Manual: Kaba Access Lock Command Options with Descriptions - E-Plex/PowerPlex 2000 Series Product Guide
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Quick
Reference
Series Guide
Summary of Pushbutton Programming Commands
Name
Diagnostic
Command
Description of Command
500 #
123456789*0#
Visual Feedback Message Definitions
Condition
Valid pushbutton
pressed
Timeout expired
Valid access
code keyed
Access granted
Red LED
Duration
OFF
ON
1 sec; A
ON
ON
Access granted
(battery low condition)
ON
Valid programming
entry
ON
Access denied
Invalid programming
entry (including
duplicate access code)
Tamper shutdown
beginning
Tamper shutdown state
Parameters
Green LED
ON
OFF
OFF
OFF
OFF
2000 Series
‘Manual diagnostic’
OFF
OFF
OFF
ON
ON
OFF
ON
ON
ON
Rate
E2000 Operation: Enter your valid PIN to Access the lock and/or to program the
lock at its keypad.
Once
PowerPlex 2000 Operation: This model is a self-powered lock. To access and/or
program the lock, you must first generate power by depressing the front lock
lever down at least once. This energizes the lock temporarily for a few seconds ,
enough time for you to enter your PIN and open the lock, or start to program the
lock with a command sequence.
1/10 sec
Once
1 sec
Once
1/10 sec
1/10 sec
1 sec; A
1 sec
1 sec; A
2 sec
1 sec; C
1 sec
1 sec
Once; B
Once
Once; B
Once
10 sec
Tamper shutdown
ending
ON
OFF
2 sec; C
Once
Lock is ready when front
lever is depressed
ON
OFF
1/10 sec
Once
For PowerPlex 2000 only:
Lock’s stored power is
starting to fade
OFF
ON
1/10 sec
1 sec
A = 1/10 second; B = Twice; C = Can be observed only when you pump the lock’s lever
To begin, put lock in programming mode by pressing: #Master Code#
Summary of Pushbutton Programming Commands
Name
Configur
Command
‘Modify Master User Access Code (lock’s
activation)’ (Always 8 digits)
004 #
‘Unlock time setup’ (TT = 02 to 20 seconds)
005 #
TT#
‘Passage Mode Timeout setup’ (TT = 01 to 24
hours - duration time in hours; 00 = no time limit)
Note: Not applicable to PowerPlex 2000 models
006 #
‘Tamper time setup’ (TT = 00 to 90 seconds)
007 #
‘Tamper wrong try setup’ (TT = 03 to 09)
008 #
‘Buzzer volume control’ (VV = 00 to 03; 00 = off;
01 = Low; 02 = Normal; 03 = High)
MMMMMMMM#
MMMMMMMM#
TT#
TT#
TT#
VV#
009 #
‘Modify access length’ (LL = 04 to 08 digits)
099 #
‘Reset to factory default values’, except access
code length. (Master, manager and access user
are retained if already programmed.)
LL#
www.kabaaccess.com
PKG3172 0313
Description of Command
000 #
Summary of Pushbutton Programming Commands
Name
Add/Modify
Users
Command
100 #
NNN #
UUUU {UUUU}#
UUUU {UUUU}#
101 #
NNN #
UUUU {UUUU}#
UUUU {UUUU}#
Delete
Users
102 #
NNN #
UUUU {UUUU}#
UUUU {UUUU}#
HH#
200 #
NNN#
201 #
NNN#
202 #
NNN#
299 #
Description of Command
‘Add/Modify User Access Code’ NNN = specific
User ID location (001 to 099) (Combination length
can be 4 to 8 digits, depending on access length
LL setting)
Summary of Pushbutton Programming Commands
Name
Activate
Users
‘Add/Modify Manager Access Code’ NNN =
specific User ID location (001 to 099)
(Combination length can be 4 to 8 digits,
depending on access length LL setting)
‘Delete Manager Access Code’
‘Delete Service User Access Code’
‘Delete all User Access Codes’ (except Master and
Manager)
Description of Command
NNN#
NNN = specific User ID location (001 to 099)
300 #
‘Activate Manager Access Code’
302 #
‘Activate Service User Access Code’
NNN#
NNN = specific User ID location (001 to 099)
398 #
399 #
De-Activate
Users
‘Activate User Access Code’
301 #
NNN#
‘Add/Modify Service User Access Code’ NNN =
specific User ID location (001 to 099) (HH = 01
to 24 hours - duration time in hours; 00 = onetime entry; Combination length can be 4 to 8
digits, depending on access length LL setting)
Delete User Access Code’
Command
P#
400 #
NNN#
401 #
NNN#
402 #
NNN#
498 #
499 #
L#
NNN = specific User ID location (001 to 099)
‘Activate all User Codes’ (except Master and
Manager)
‘Activate / De-Activate Passage Mode’ (P = 0
or 1; 0 = disable Passage Mode; 1 = enable
Passage Mode)
‘De-Activate User Access Code’
NNN = specific User ID location (001 to 099)
‘De-Activate Manager Access Code’
NNN = specific User ID location (001 to 099)
‘De-Activate Service User Access Code’
NNN = specific User ID location (001 to 099)
‘De-Activate all User Codes’ (except Master and
Manager)
‘Activate / De-Activate Lockout Mode’ (Master User
is not affected by Lockout Mode) (L = 0 or 1; 0 =
disable Lockout Mode; 1 = enable Lockout Mode)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 2 Create Date : 2013:03:15 08:35:38-05:00 Modify Date : 2013:03:15 08:35:38-05:00 Producer : QuarkXPress(R) 9.3 Title : Operations Manual Creator : QuarkXPress(R) 9.3EXIF Metadata provided by EXIF.tools