Kaba Simplex 3000 Changing The Code KAA1155

User Manual: Kaba Simplex 3000 Changing the Code - KAA1155 Simplex 3000 Mechanical Lock - Kaba Access & Data Systems

Open the PDF directly: View PDF PDF.
Page Count: 2

DownloadKaba Simplex 3000 Changing The Code - KAA1155 Simplex-3000-changing-the-code-kaa1155
Open PDF In BrowserView PDF
Changing the Code/Combination
Simplex 3000
Note: If your lock is opening on every turn of the knob or lever, except upon entering a code, this may
be a ZERO CODE. Before attempting to remove the lock from the door, refer to the troubleshooting
procedures outlined at bottom of this document for a zero code symptom/solution.

3000 Series FAQ
Changing the Code/Combination
Important: Perform this procedure with the DOOR OPEN. The lock should be
set for pushbutton access to retract latch.
Tools Required: DF59 Control Key & Small flat 1.8" blade screwdriver.
Read the instructions through once before attempting to change
the combination.
The factory pre-set combination is 2 and 4 pressed simultaneously (and released), then press 3 (and release).
1.
		
		
		

Remove the control lock assembly and trim plate using the DF59 Control
Key provided with the lock (see figure 1). Turn the key to the left
(counterclockwise) until control lock assembly can be removed and the 		
combination change sleeve is exposed (see figure 2).

2.
		
		

Turn the outside thumb piece to the left (counterclockwise) to the stop 		
position and release. This clears the lock of previously used buttons
(see figure 3).

3.
		

Enter the existing combination. Make sure you depress each button fully
and release.

4.
		
		
		

Insert screwdriver into combination change sleeve slot (see figure 2).
Turn screwdriver to the right (clockwise) to the stop position. You should
feel a slight click. Turn the screwdriver to the left (counterclockwise) to 		
stop, and remove.

5.
		

Rotate the thumb piece to the left (counterclockwise) to the stop
position and release. This clears the old combination (see figure 3).

6.
		
		
		

Select a new combination, write it down. Some or all of the buttons may
be used for your new combination - pressed individually or simultane-		
ously. Each button may be used only once. We do not recommend the 		
use of a one-button combination.

7.
		
		

With the door open, enter your new combination. Depress each button fully and release
it. You must feel a click each time you press a button to know that the button was
fully depressed.

8.
		

Turn the thumb piece to the right (clockwise) to the stop position to activate the new
combination—note that latch is retracted. Release thumb piece (see figure 4).

9.
		
		
		

Replace control lock assembly and trim plate by inserting threaded rod portion into the
combination change sleeve and turning to the right (clockwise) until trim plate is snug up
against stile of door. The DF59 Control Key can be removed from the control lock assembly
in a vertical or horizontal position only.

10.
		

BEFORE CLOSING THE DOOR, enter the new combination and turn the thumb piece to the
right (clockwise) to insure proper retraction of latch.

Note:
• Do not force at any time.
•

If a wrong combination is entered while operating the lock, turn the outside thumbturn to the
left (counterclockwise) to the stop position and release. This will clear any previously depressed
buttons. Enter in the correct combination.

Troubleshooting
Symptom/problem: Turning outside thumbturn clockwise always retracts latch without depressing
any buttons.
Cause: Lock is in zero combination.
Solution: Follow the procedure for setting a new combination except omit step 3.

KAA1155 0108
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Instance ID                     : uuid:2e74958c-bc02-427c-817d-e0a409c87502
Document ID                     : adobe:docid:indd:51b9a144-bec6-11dc-8bea-857120353c38
Rendition Class                 : proof:pdf
Derived From Instance ID        : 51b9a143-bec6-11dc-8bea-857120353c38
Derived From Document ID        : adobe:docid:indd:51b9a140-bec6-11dc-8bea-857120353c38
Manifest Link Form              : ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 300.00, 300.00
Manifest Placed Y Resolution    : 300.00, 300.00
Manifest Placed Resolution Unit : Inches, Inches
Manifest Reference Instance ID  : uuid:70B0B614BEC811DCA35CD13DBAF657AB, uuid:B48417FFBEC611DCA35CD13DBAF657AB
Manifest Reference Document ID  : uuid:70B0B613BEC811DCA35CD13DBAF657AB, uuid:B48417FEBEC611DCA35CD13DBAF657AB
Create Date                     : 2008:01:11 11:39:45-05:00
Modify Date                     : 2008:08:18 15:01:21-04:00
Metadata Date                   : 2008:08:18 15:01:21-04:00
Creator Tool                    : Adobe InDesign CS3 (5.0.1)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 12202 bytes, use -b option to extract)
Format                          : application/pdf
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Page Count                      : 2
Creator                         : Adobe InDesign CS3 (5.0.1)
EXIF Metadata provided by EXIF.tools

Navigation menu