Kaba Simplex 900 Changing The Code KAA1160

User Manual: Kaba Simplex 900 Changing the Code - KAA1160 Simplex 900 Mechanical Lock - Kaba Access & Data Systems

Open the PDF directly: View PDF PDF.
Page Count: 2

DownloadKaba Simplex 900 Changing The Code - KAA1160 Simplex-900-changing-the-code-kaa1160
Open PDF In BrowserView PDF
Changing the Code/Combination
Simplex 900
Note: If your lock is opening on every turn of the knob or lever, except upon entering a code, this may
be a ZERO CODE. Before attempting to remove the lock from the door, refer to the troubleshooting
procedures outlined at bottom of this document for a zero code symptom/solution.

900 Series FAQ
Changing the Code/Combination

The door must be open.
1.
		
		

Turn the outside thumbturn to the left (counterclockwise) to the stop
position; then release. This will clear any random entries from the
mechanism.

Note: When the thumbturn is turned to the left on a deadbolt model, the bolt is
automatically thrown into the locked position; therefore, it is important to keep
the door open while changing the combination.
2.
		
		

Enter the existing combination. On new installations, use the factory-set
combination: depress 2 and 4 simultaneously, (release), then 3 (release). 		
You should feel a slight click as each button is depressed.

3.
		

Use the Allen wrench to remove the screw from the top of the lock
housing (see figure 1).

4.
		
		

After removing the screw. Insert the Allen wrench into the hole and
depress the internal lockout slide; you should feel a slight click.
Do not force.

5.

Remove the wrench.

6.
		

Turn the outside thumbturn to the left (counterclockwise) to the stop 		
position, then release.

7.
		
		

Choose your new combination, write it down, then enter the new
combination—depress buttons carefully (a slight click should be felt as 		
each button is depressed).

Note: You can use one button or all five for a combination, but each button can
only be used once. You can depress two or more buttons simultaneously as a
step in the combination.

8.
		
9.

Turn the outside thumbturn to the right (clockwise) to the stop position; then release. The
new combination is now active.
Test your new combination a few times before you shut the door.

Lock and unlock the door following the instructions in section 6.
If the outside thumbturn retracts the latch or bolt and you have not entered your combination, steps
were done out of order and the lock is in zero code.
10.
		
11.

Repeat steps 4 to 8 until the latch or bolt retracts only after you enter your
new combination.
Replace the screw on the top of the lock housing.

Note: The outside thumbturn cannot be forced to retract the latch / bolt because it is connected to
the lock housing by a friction clutch. If the thumbturn has been forced, it can be turned back to the
vertical position by hand without damaging the lock.
Troubleshooting
Symptom/problem: Turning outside thumbturn always retracts latch/bolt without depressing without any buttons.
Cause: Lock is in zero combination.
Solution: Follow the procedure for changing a combination, but omit step 2.

KAA1160 0108
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Create Date                     : 2008:01:11 11:40:35-05:00
Creator                         : Adobe InDesign CS3 (5.0.1)
Modify Date                     : 2014:03:24 13:21:52-04:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Instance ID                     : uuid:7afe8fb8-82fd-4c03-b1af-2279d70e8c3b
Document ID                     : adobe:docid:indd:4c13b5dc-bf94-11dc-b625-b5eb45d47af5
Rendition Class                 : proof:pdf
Derived From Instance ID        : 4c13b5db-bf94-11dc-b625-b5eb45d47af5
Derived From Document ID        : adobe:docid:indd:4c13b5d9-bf94-11dc-b625-b5eb45d47af5
Manifest Link Form              : ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 300.00, 300.00
Manifest Placed Y Resolution    : 300.00, 300.00
Manifest Placed Resolution Unit : Inches, Inches
Manifest Reference Instance ID  : uuid:8C8D8DEBBF8211DCB13DABE2189ABB81, uuid:FB73350ABF7211DCB13DABE2189ABB81
Manifest Reference Document ID  : uuid:8C8D8DEABF8211DCB13DABE2189ABB81, uuid:FB733509BF7211DCB13DABE2189ABB81
Metadata Date                   : 2014:03:24 13:21:52-04:00
Creator Tool                    : Adobe InDesign CS3 (5.0.1)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 9819 bytes, use -b option to extract)
Format                          : application/pdf
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Page Count                      : 2
EXIF Metadata provided by EXIF.tools

Navigation menu