Kanto Living 2YEKN002 Active Loudspeaker System User Manual
Kanto Distribution Inc. Active Loudspeaker System
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2121848 |
| Application ID | qe6r7Ck00rhYMIICss3LoA== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 336.33kB (4204116 bits) |
| Date Submitted | 2013-11-18 00:00:00 |
| Date Available | 2013-11-18 00:00:00 |
| Creation Date | 2013-10-28 16:42:04 |
| Producing Software | Adobe PDF Library 10.0.1 |
| Document Lastmod | 2013-10-29 16:37:38 |
| Document Title | User Manual |
| Document Creator | Adobe InDesign CC (Macintosh) |
English User Manual YU5 Powered Speakers YUMI POWERED SPEAKERS Supporting your digital lifestyle™ Table of Contents Important Safety Precautions . . . . Introduction / What’s in the Box? . . Front & Rear Panels . . . . . . . . . Remote Control . . . . . . . . . . . Setting Up Your Speakers . . . . . . . Connecting Audio Sources . . . . . . USB Charging . . . . . . . . . . . . Connecting a Sub-Woofer . . . . . . . Specifications . . . . . . . . . . . . . Warranty . . . . . . . . . . . . . . . . 7 . 9 . 10 . 11 . 12 Important Safety Precautions ATTENTION The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the apparatus. • • • • • • • • • • • CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE BACK PANEL. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Protect the power-supply cord from being walked on or pinched, particularly at plugs, convenience receptacles and the point where they exit from the apparatus. Only use attachments / accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. • • • • • DANGEROUS VOLTAGE The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user of the presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, the apparatus does not operate normally, or the apparatus has been dropped. Apparatus shall be connected to a MAINS socket outlet with a protective earthing connection. An appliance input coupler is used as the disconnect device - the disconnect device shall remain readily operable. Batteries or battery packs shall not be exposed to excessive heat such as sunshine, fire or the like. IC Caution RSS-Gen Issue 3 December 2010"&"CNR-Gen 3e éditionDécembre 2010: - English: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. - French: Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d'encompromettre le fonctionnement. FCC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modi�cations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between theequipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Industry Canada Notice: Complies with CAN ICES-3(B) / NMB-3(B) Introduction Thank you for choosing YU5 Powered Speakers, designed by Kanto in Canada. YU5 outputs 40W RMS per channel into 4 Ohm speakers, for remarkably bold and clean sound. Excellent sensitivity and frequency response provide deep thumping lows and clear, scintillating highs. YU5 is an amazingly flexible speaker system that can accept five input sources and connect to a subwoofer for enhanced low frequency effects (LFE). Additionally, it is equipped with the latest Bluetooth technology and a USB port for charging USB devices. YU5 operates on a multi-voltage power source from 110 V to 240 V and can be used worldwide. We recommend you read all instructions carefully before using the system and keep them for future reference. Kanto cannot be liable for damage or injury caused by incorrect setup or use of this product. This powered speaker system was carefully tested and inspected during production, and before packaging and shipping. After unpacking, please check for any damage. It is rare that a unit is damaged during shipping, but if this happens contact your retailer immediately. You can also call Kanto directly at 1-888-848-2643 or email support@kantoaudio.com. What’s In the Box? RCA AUX OPT1 BASS YU5 Active Speaker (Left Channel) YU5 Passive Speaker (Right Speaker) OPT2 TREBLE BALANCE x2 x3 YU5 Remote ‘AAA’ Batteries User Manuals x8 Self-Adhesive Rubber Feet Power Cord Speaker Wire (10’) 3.5 mm cable AUX (10’) Supporting your digital lifestyle™ Front & Rear Panels FRONT PANEL 1” Silk Dome Tweeter 5.25” Kevlar Mid/Woofer Driver LED Blue - Power on / Playback Mode Yellow - Standby (solid) - Mute (flashing) White - Discover Mode (flashing) - Paired (solid) Volume / Input Select Knob REAR PANEL RCA L/R Input 3.5 mm Stereo Mini-Jack AUX Input Subwoofer Output Optical 1 and Optical 2 Inputs Right Channel Output Terminals (+ and −) for Passive Speaker Connection 10 USB Charge Port (5 V 2.1A) 11 ON / OFF Switch 12 AC Input Connection (100 V - 240 V) Volume/Input Select Knob YU5’s volume knob functions as an input select knob as well. Push the knob to select an input source - it cycles through the following inputs depending on what input source was last used. RCA AUX OPT1 OPT2 BLUETOOTH 10 11 12 Remote Control Install two supplied AAA batteries in the back of your YU5 remote. Remote Control functions are listed below. Standby Button - press to enter Standby Mode or return to Playback Mode RCA Input Select 3.5 mm Stereo Mini-Jack AUX Input Select Optical 1 Input Select Optical 2 Input Select Bluetooth Input Select Bluetooth Reset Increase Volume 10 11 Decrease Bass Output 12 Reset Bass Output 13 Increase Treble Output 16 Mute 17 Balance Control Left Channel OPT1 OPT2 13 TREBLE 11 14 12 16 17 15 BALANCE 18 19 14 Decrease Treble Output 15 Reset Treble Output AUX BASS Decrease Volume 10 Increase Bass Output RCA 20 22 21 18 Balance Control Right Channel 19 Reset Balance (Left and Right Channels) 20 Previous Track (Bluetooth Operation) 21 Play / Pause (Bluetooth Operation) 22 Next Track (Bluetooth Operation) Supporting your digital lifestyle™ Setting Up Your Speakers The YU5 powered speaker system is designed for either bookshelf or stand mounting. The stands should be of rigid construction, between 45 cm to 69 cm high and preferably have spikes. We recommend the Kanto SP130 speaker stands to go with your YU5. The space between the two speakers and the distance from the listener is important. If the speakers are positioned too close or too far apart, stereo imaging will not be fully developed. YU5 is designed to perform optimally positioned at least 20 cm from the rear wall in an average listening room. However, it may not be possible to install the speakers in this position and since rooms vary in shape, size, and furnishing, a certain amount of experimentation is necessary to determine the most suitable position. Moving the speakers very close to the rear wall will enhance the bass frequencies but will tend to reduce soundstage depth, while moving the speakers away from the rear wall will tend to have the opposite effect. Avoid positioning the speakers close to or in the corners of the room, as this will excite undesirable room coupling in the low and middle frequencies. If the width of the rear wall is limited then toe-in the speakers slightly to reduce reflections. Room characteristics and positioning have a profound effect on the performance of the speakers, so time and effort devoted to achieving the optimum positions will be rewarded. Ensure that the ON/OFF Switch is in the OFF position. Connect the two speakers together as shown below using the supplied speaker cable. Connect the RED (+) and BLACK (−) terminals from the active speaker (left channel) to the corresponding terminals on the passive speaker (right channel). If you wish to place your speakers farther apart than the supplied cable will reach, we recommend that you purchase a heavier gauge of speaker cable to minimize signal loss. Follow the instructions on the ensuing pages to connect your audio sources to YU5. The examples in the following pages are not meant to be exhaustive - just examples. Connect the power cord from YU5’s active speaker to the wall outlet. ATTENTION When connecting audio cables the ON/OFF Switch must be turned OFF. After connecting all cables, the unit can be turned ON. When the volume is high, this system can produce noise levels that could permanently damage your hearing. YU5 is a self-powered speaker system. Do not connect the speaker terminals to the speaker outputs of a stereo amplifier. Damage may occur. Use only the power cord provided with the speakers. Connecting Audio Sources YU5 features a high quality DAC (digital-to-analog converter) that supports data streams up to 24-bit/192 kHz resolution. YU5 supports Bluetooth 4.0 with aptX CODEC technology. Use the appropriate audio cable to connect your audio source components to your speakers. Refer to the following diagrams on connectivity options. • 3.5 mm stereo mini-jack AUX cable • Stereo RCA to 3.5 mm stereo mini-jack ‘Y’ cable • Optical Toslink cable RCA & 3.5 mm Stereo Mini-Jack AUX Connection AUDIO TURNTABLE OUT IN PHONO PRE-AMP (if necessary)* LAPTOP 3.5mm MP3 DOCK CD / DVD MP3 ATTENTION *Some models of turntables include a built-in Phono Pre-Amp. Supporting your digital lifestyle™ Optical & Bluetooth Connection GAME CONSOLES OPT 1 OPT 2 MOBILE DEVICES MEDIA PLAYERS DIGITAL DOCK Bluetooth Pairing YU5 features Bluetooth 4.0 with aptX CODEC technology and can be paired with many devices for wireless audio playback from your phone, MP3 player or tablet. Pairing is easy. 1. Press the Bluetooth button on YU5’s remote to select it as the input source. The Bluetooth LED (white) will flash slowly to indicate that YU5 is in pairing mode. 2. Enable your Bluetooth device to search for a new device to pair with. Select ‘YU5 by Kanto’ from the list of Bluetooth devices available for pairing. 3. If pairing is successful, the Bluetooth LED (white) will remain solid. You will not need to pair the same Bluetooth device again - ‘YU5 by Kanto’ will remain on your device list until you remove it from the list. 4. If the device does not pair with YU5, turn the speaker’s ON/OFF Switch to the OFF position, then repeat Steps 1 to 3. Alternatively, you can turn off Bluetooth in your device and turn it back on again. Bluetooth Operation 1. We recommend keeping a maximum distance of 10 meters between the speaker and your device. The best signal fidelity is within this range. 2. If pairing is successful, the connection between the speaker and your device remains active and functional – that is, you can stream audio from your device to the speaker using either the player control buttons of your device or the control buttons of the remote control (see diagram of Remote Control on page 5 of this manual – buttons #20, #21, and #22). 3. Take note of the following behavior and functionality during Bluetooth operation. When you are successfully connected, the Bluetooth LED will be lit solid, and your device will show as connected to ‘YU5 by Kanto’. • The connection between speaker and device remains active even if input source has changed. For instance, you can switch to another input source (e.g. CD player) and return to Bluetooth operation without losing signal connection and, therefore, do not need to pair with the device again. • When the speaker is put in Standby mode or powered OFF, Bluetooth connection with the device is lost. When the speaker returns to Playback mode, the Bluetooth connection between the speaker and device is re-established. However, you may notice a choppy playback signal for approximately 30 seconds after reconnection. It will normalize. • While the speaker can be paired with more than one device, only one device can play and transmit audio signal at a time. 4. The YU5 remote control features a Bluetooth Reset button to quickly disconnect a paired device and allow a second device to pair with the speaker (button #7 on the Remote Control diagram on page 5). • Press Bluetooth Reset button to disconnect a paired device. • Follow the pairing instructions to pair another device. • The same behavior and functionality apply to the second device. USB Charging Operation YU5 features one 5 V 2.1 A USB charging port on the back panel. This is a convenient power source to charge your devices. When YU5 is in Playback Mode (LED blue) and Standby Mode (LED yellow), the port is active, and whatever device is connected is able to draw up to 2.1 A of power. Supporting your digital lifestyle™ Connecting a Subwoofer YU5 is equipped with an RCA connector to provide output signal to a powered subwoofer. Simply connect a single RCA subwoofer cable from the SUB OUT connection on the YU5 to the AUDIO INPUT on your subwoofer. If your subwoofer has a stereo L/R RCA input, either left or right inputs will work. We recommend the Kanto sub6 or sub8 powered subwoofer with crossover and volume controls. Most quality subwoofers offer these controls, which allow you to customize the amount of bass you will experience. Look for details on the Kanto website at: www.kantospeakers.com Use either L or R inputs 10 Specifications YU5 POWERED SPEAKER SYSTEM Tweeters Woofers Nominal Impedance Sensitivity 2.83V (/1W/1m) Amplifier Type Power Output Input Sensitivity Total Harmonic Distortion Crossover System Crossover Frequency Frequency Range Frequency Response Inputs Outputs Speaker Terminals Input Voltage / Frequency Standby Power Consumption Remote Dimensions (each speaker) Net Weight (Active) Net Weight (Passive) Gross Weight 1 inch Silk Dome 5.25 inch Kevlar 4 Ohm 87 dB Class D 40 Watts RMS per channel 550 mV < 0.3% 2-way 2.0 kHz 20 Hz - 20 kHz 50 Hz - 10 kHz ± 6 dB 1 x 3.5 mm stereo mini-jack AUX 1 x RCA L/R 2 x Optical (Toslink) 1 x Bluetooth 4.0 (Supports aptX CODEC) 1 x Subwoofer 1 x USB Charge Port 5 V 2.1 A Left and Right Binding Posts AC 100 V - 240 V 50/60 Hz (auto switching) < 0.5 W Included W 6.8”x H 10.7” x D 8.4” (175 x 272 x 215 mm) 9.2 lbs (4.2 kg) 7.9 lbs (3.6 kg) 20.5 lbs (9.3 kg) (boxed pair) NOTICE: The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Kanto Distribution Inc. is under license. 11 Supporting your digital lifestyle™ Check out more great products from Kanto! Kanto Speakers • Check out our full line of bookshelf and desktop speaker systems • Available in a stunning array of colors • Visit kantoaudio.com for more! BEN • Full line of Audio and Video Cables • Attractive white cables and heads • HDMI, Optical, Mini-jack, RCA, USB • Switchers, Hubs, Adapters • Visit kantoliving.com/cable for more! by To learn more about all our products, visit www.kantoliving.com kantoliving kantoliving Warranty Limited Warranty To Original Purchaser Kanto Distribution Inc. (Kanto) warrants the equipment it manufactures to be free from defects in material and workmanship for the following limited warranty period of: 24 months parts and labour If equipment fails because of such defects and Kanto or an authorized dealer is notified within 24 months from the date of shipment with proof of original invoice. Kanto will, at its option, repair or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications. Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the repair. Such repairs are warranted for 90 days from the day of reshipment to the original purchaser. This warranty is in lieu of all other warranties expressed or implied, including without limitation, any implied warranty or merchantability or fitness for any particular purpose, all of which are expressly disclaimed. The information in the owner’s manual has been carefully checked and is believed to be accurate. However, Kanto assumes no responsibility for any inaccuracies that may be contained in the manual. In no event will Kanto, be liable for direct, indirect, special, incidental, or consequential damages resulting from any defect or omission in this manual, even if advised of the possibility of such damages. 13-10 www.kantoliving.com | sales@kantoliving.com Tel 888.848.2643
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Tagged PDF : Yes XMP Toolkit : 3.1-701 Instance ID : uuid:f5d44e43-e588-41ec-b8ea-2bacea1b97f1 Original Document ID : adobe:docid:indd:4d1083d6-2238-11dd-9b8a-f1baea413bca Document ID : xmp.id:f4b27248-7e12-47e2-96e2-f50d964f929b Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:3857f4a0-bf01-4b32-a217-20924a53d387 Derived From Document ID : xmp.did:41647386-5e83-4622-958d-b44f8f54f064 Derived From Original Document ID: adobe:docid:indd:4d1083d6-2238-11dd-9b8a-f1baea413bca Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC (Macintosh) History Changed : / History When : 2013:10:28 16:42:04-07:00 Create Date : 2013:10:28 16:42:04-07:00 Modify Date : 2013:10:29 16:37:38+08:00 Metadata Date : 2013:10:29 16:37:38+08:00 Creator Tool : Adobe InDesign CC (Macintosh) Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 12 Creator : Adobe InDesign CC (Macintosh)EXIF Metadata provided by EXIF.tools