Kenmore Elite 25344713101 User Manual FREEZER Manuals And Guides L0504505

FRIGIDAIRE Upright Freezer Manual L0504505 FRIGIDAIRE Upright Freezer Owner's Manual, FRIGIDAIRE Upright Freezer installation guides

User Manual: Kenmore Elite 25344713101 25344713101 KENMORE ELITE FREEZER - Manuals and Guides View the owners manual for your KENMORE ELITE FREEZER #25344713101. Home:Kitchen Appliance Parts:Kenmore Elite Parts:Kenmore Elite FREEZER Manual

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

lytstallation

from electrical

Ice Maker To Water Supply

To avoid electric shock, which can cause death or severe persona[ injury, disconnect
power before connecting a water supply line to the freezer.
To Avoid Property

-

o Connecting

the freezer

Damage:

Copper tubing is recommended for the water supply line.Water supply tubing made of 1A" pJastic is not
recommended since it greatly increases the potentiaJ for water [eakso Manufacturer will not be responsiMe
any damage if plastic tubing is used for suppJy Hne.

•
•

DO NOT install water suppJy tubing in areas where tern peratures fall beJow freezing.
C hemicais from a maffunctioning
softener can damage the ice maker, ff the ice maker is connected
water, ensure that the softener is maintained and working property.

for

to soft

IMPORTANT: Ensure that your water supply line connections comply with all local plumbing codes.
Before Installing The Water Supply Line, You WiH Need
*
BasicToo[s: adjustable wrench, flat-blade screwdriver, and Phillips TM screwdriver
*
Access to a household cold water line with water pressure between 20 and 120 psi.
*

A water supply line made of ¼ inch (6.4 mm) OD, copper tubing. To determine the length of copper tubing needed,
you will need to measure the distance from the ice maker inlet valve at the back of the freezer to your cold water
pipe. Then add approximately 7 feet (2.1 meters), so the freezer can be moved out for cleaning (as shown).
A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type
shutoff valve.

*
*

A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.
NOTE: Water line kit number 53039i7950, available from your appliance dealer at additional COst,Contains 25 feet (7.6
meters) of 1_-_inch QD copper tubing, a saddle type shutoff valve (nonpierc ng) (2) 1_;_inch brass compression nuts (2)
ferrubsisbeves,
and instructions for installing a water supply line:

To Connect Water Supply Line To Ice Maker Inlet Valve
\Clamp vau_
freezer from electric power source,
2, Disconnect
P
ond
of
w
supp
,no
yline
,nto
s,nk
orbucket,
Turn
ON
waterace
supply
andator
flush
supply
until
water
is clear,
Turn
1,

3,
4,
5,

\-inlet

o

OFF water supply at shut off valve,
Unscrew plastic cap from water valve inlet and discard cap,
Slide brass compression nut, then ferrule (sleeve) onto water
supply line, as shown,
Push water supply line into water valve inlet as far as it will
go (¼ inch), Slide ferrule (sleeve) into valve inlet and finger
tighten compression nut onto valve. Tighten another half
turn with

6,

\

a wrench;

DO NOT

over

tighten,

"-Compression

,,

Nut

X C0pPer
waier
LineF_om

With steel clamp and screw, secure water supply line to
rear panel of freezer as shown.
Household Water Supply
7. Coil excess water supply line (about 2_/2turns) behind freezer
as shown and arrange coils so they do not vibrate or wear against any other surface.
8. Turn ON water supply at shutoff valve and tighten any connections that leak.
9. Reconnect freezer to electrical powersource.
10. To tu rn ice maker on, lower wire signal arm (see ice maker front cover for ON/OFF position of arm).

ice. Air in new plumbing lines may
cause ice maker to cycle two or three times before making a full tray of [ce_New plumb!ng may cause ice to be discobred
or have poor flavor. Discard ice made during the first 24 hours.
PN: 216901700B

{

{

i

:

t

¸

t

t

x

@e Service

ifof your
be for
freezer
normaU
has
use.
anDuring
automatic
the initiaU
ice maker,
startupit of
wHU
your
provide
freezer,
a sufficient
however, suppUy
no be
wHUbe produced during the first 24 hours of operation. Automatic ice makers
are aUso optionaU accessories that may be installed in some modeb at any
time. Call your UocaU
deabr for information.
TURNING

YOUR ICE MAKER

ON

After the plumbing connections have been completed, the water supply valve
must be opened, Place the ice container under the ice maker, pushing it as far
back as possible, Lower the wire signal arm to its "down" or ON position, New
plumbing connections may cause the first production of ice cubes to be
discolored or have an odd flavor, These first cubes should be discarded until
the cubes produced are free of discoloration and taste,
TURNING

YOUR iCE MAKER

OFF

To stop the ice maker, lift the wire signal arm until it clicks and locks in the
"up" or OFF position, The ice maker also turns off automatically when the ice
container is fuji, if your model has an adjustable freezer shelf, place the shelf
in the lower position, so thal the wure signal arm wi hit the ce when the
container is full,

ice Maker
Leveling Bracket

iMPORTANT: Your ice maker is shipped with the w_resugnal arm in the
ON position. To ensure proper function of your ice maker, hook up water
supply immediately or turn _cemaker OFF by lifting the wire signal arm
until it clicks and locks in the UP position.
IMPORTANT: Check the leveling bracket on the ice maker to ensure the
ice maker is level, if the gap between the freezer wall and the ice maker
is the same at top and bottom, then the ice maker is level.
I the ice maker is not level, loosen the screw and slide the bracket to

Container

\
1" or less

the correct position to make it level, Retighten the screw.
You'll need a 1/4" socket wrench for this task,
iCE MAKER

TiPS

ice cubes stored too long may develop an odd flavor, Empty the ice container and ensure that the wire signal arm is in
its "down" or ON position, The ice maker will then produce more ice,
Occasionally shake the ice container to keep ice separated,
Keep the wire signal arm in its "up" or OFF position until the freezer is connected to the water supply or whenever the
water supply is turned off,
The following sounds are normal when the ice maker is operating:
o

ice loosening from tray

o

ice dropping into ice container
Running water
Water valve opening or closing
Not place the !oe centa!ner

!n your d!shwasher,

Wash the ice container in warm water with mild detergent, Rinse well and dry,
o

Stop the ice maker when cleaning the freezer and during vacations,
if the ice maker will be turned off for a long period of time, turn the water supply valve to the closed position,

PN: 216901700B



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 2
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Fri Apr 20 12:18:18 2007
Author                          : 
Title                           : 
Subject                         : 

EXIF Metadata provided by EXIF.tools