Kenmore 11622614310 User Manual VACUUM Manuals And Guides 1307364L

User Manual: Kenmore 11622614310 11622614310 KENMORE VACUUM - Manuals and Guides View the owners manual for your KENMORE VACUUM #11622614310. Home:Vacuums & Floor Care Parts:Kenmore Parts:Kenmore VACUUM Manual

Open the PDF directly: View PDF .
Page Count: 56

Download
Open PDF In Browser	View PDF

Use & Care Guide
Manual de Uso y Cuidado

I
_-"___-_'
r_F__r....

_
Side
Latch

End Cap

-___..

2. Push agitator
assembly back
into PowerMate.

Kear
Latches

4. To remove covert
grasp the sides and
pull out.

of cover and
3. Line Rest
up front
base.

..............
_-___

edge of base as
cover on front
shown.
__,,__

5. Lift agitator
assembly out
and remove
worn belt.

.o,a,°
covo
,_ _;'-_{'_--_-back. Press cover

__

and
snap rear
into latches
place.
Side

Latch

6. Check and clean end cap areas. See TO
CLEAN AGITATOR (page 22) section and
AGITATOR ASSEMBLY illustration (page 22)
for picture of complete agitator assembly.

Base

Rear

Latches

Make sure there is no gap between
cover and base.

the

5. Turn PowerMate upside down and replace two (2) cover screws.
= 21 =

TO CLEAN AGITATOR:

iMPORTANT

NOTE: In order to keep cleaning efficiency
high and to prevent damage to your vacuum
cleaner, the agitator must be cleaned every
time the belt is changed.

Turn off and unplug vacuum cleaner from
electrical outlet. Check and remove hair,
stringand lint build-up frequently in the
PowerMate agitator and end cap areas.

The agitator must also be cleaned
ing to the following schedule:

Vacuum leaner

se

accord-

Remove any dirt or debris
area or in the brush roller

in the belt path
area.

Carefully remove any string or debris located on the agitator or end caps.

_itator

HEAVY (used daily)

every week

MODERATE (used 2-3 times/week)

every month

LIGHT (used 1 time/week)

every 2 months

AGITATOR
IEnd

CaP

ASSEMBLY
Beff

Pafh_

LIGHT BULB CHANGING

WARNING

_

Electrical Shock Or Personal injury
Hazard

CAUTION

Do not use a bulb rated over 9W (13V).
During extended use, heat from the bulb

Turn off and unplug vacuum cleaner
before performing maintenance to the
vacuum cleaner. Faiiure to do so could
result in electrical shock or personal
injury from the vacuum cleaner
suddenly starting.

Push in
to right

3. To replace the
light bulb,
carefully
insert
fully into slot.

i ,cAuT,o.
_Do not plug in or turn on until the vacuum
cleaner

is completely

4. Reinstall PowerMate cover as shown in
BELT CHANGING AND AGITATOR
CLEANING (page 21-22).

reassembled.

1. Remove PowerMate
cover as shown in
BELT CHANGING
AND AGITATOR
CLEANING
_Pull

|
_ '2. Remove the light

out to
left side

_

NOTE: See PARTS AND FEATURES (page
for Bulb number.

(pages 21-22).

L

bulb by pulling

straight

out.

- 22 -

5)

AGITATOR SERViCiNG
TO REPLACE AGITATOR
ASSEMBLY

,_WARNING
Electrical Shock Or Personal injury

Hazard

Turn off and unplug vacuum cleaner elec=
frlcal supply before performing malnte=
nonce to the vacuum cleaner. Failure to do

1. Remove PowerMate cover, belt and
agitator assembly. See "To Remove Belt" in
BELTCHANGING AND AGITATOR
CLEANING (pages 21-22).

so could result in electrical shock or per=
sonal injury from vacuum cleaner sud=
denly starting.

2. Replace

TO CHECK THE BRUSHES
When

New

bars, replace

Brushes

the agitator

Worn

assembly.

3. Reinstall belt and PowerMate cover. See
"To replace belt" in BELT CHANGING
AND
AGITATOR CLEANING (pages 21-22).

brushes are worn to the level of the

base support
assembly.

agitator

Brushes

Bose

Support
Bar

= 23 =

Review
thistable to find

do-it-yourself solutions for minor performance problems. Any other
service needed should be performed by a Sears or other qualified service agent.

WARNING
Always

turn

off

and

vacuum cleaner.

unplug

vacuum

cleaner

before

performing

Failure to do so could result in electrical

Vacuum cleaner
won't start.

1.

Unplugged

at wall

2. Tripped
circuit breaker/
blown fuse at household

Poor job of dirt
pick-up.

service panel.
Loose hose electrical
connections.

1.
2.
3.
4.
5.
6.

Full or clogged dust cup.
Clogged airflow passages.
Dirty filters.
Wrong pile height setting.
Suction control is open.
Hole in hose.

7.
8.
9.
10.

Worn PowerMafe agitator.
Worn or broken belt.
Dirty agitator or end caps.
Dust cup installed
incorrectly.
11. Dust cup lid and dust cup
missembled.

Vacuum cleaner starts
but shuts off.

1. Hose electrical

3. Tripped
thermal
in canister.

PowerMate will not
run when attached.

1. PowerMate

3. Reconnecf

Empty and clean dust cup.
Clear airflow passages.
Change/clean
filters.
Adjust setting.
Adjust control.
Replace hose.
Change agitator.
See BELT CHANGING AND
AGITATOR CLEANING.
10. See EMPTYING DUST CUP.
11. See PRE-FILTER

1.

protector

belt.

3. Dirty agitator
or end caps.
4. Tripped
overload
protector
in PowerMate.

5. Switch not in CARPET
position.

= 24 =

Check connections,
hose ends.

CLEANING.

reconnect

2. Remove any items that may be
caught or jammed,
then reset. If
vacuum cleaner
starts and stops
again, clean agitator
and end

protector

3.

connections

unplugged.
2. Worn or broken

hose ends.

1.
2.
3.
4.
5.
6.
7.
8 & 9.

connection.

2. Tripped overload
in PowerMate.

to the

1. Plug in firmly, move switch to
FLOOR or CARPET position.
2. Reset circuit breaker or replace
fuse.

outlet.

3.

maintenance

shock or personal injury.

caps, then reset.
Reset thermal
protector.

1. Plug in firmly.
2&3.

See BELT CHANGING
AGITATOR
CLEANING.
4.

5.

AND

Remove any items that may be
caught or jammed,
then reset. If
vacuum cleaner
starts and stops
again, clean agitator
and end
caps, then reset.
Move switch to CARPET position.

Vacuum cleaner picks
up moveable
rugs
-orPowerMate

1. Wrong
2. Suction

pile height
too strong.

setting.

1. Adjust setting.
2. Open suction control.

pushes too hard.

Light won't work.

1. Burned out light bulb.
2. Tripped overload protector
in PowerMafe.

2. Remove any items that may be

Cord won't rewind.

1. Dirty power cord.
2. Cord jammed.

1. Clean the power cord.
2. Pull out cord and rewind.

Vacuum cSeaner
leaves marks on
carpet.

1. Wrong vacuuming

pattern.

1.

Change

bulb.

caught or jammed,
then reset. If
vacuum cleaner
starts and stops
again, clean agitator
and end
caps, then reset.

1. See VACUUMING

Vacuum Cleaner Help Line:
1-877-531-7321
8:00am-5:00pm
EST, M-F
(U.S.A. and Canada)

- 25 -

light

TIPS.

Master

Protection

Agreements

Congratulations on making a smart purchase. Your new I
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 56
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Fri Apr 11 07:24:16 2014
Author                          : 
Title                           : 
Subject                         : 

EXIF Metadata provided by EXIF.tools