Kenmore 40180082010 User Manual MICROWAVE Manuals And Guides L0709302

KENMORE Microwave/Hood Combo Manual L0709302 KENMORE Microwave/Hood Combo Owner's Manual, KENMORE Microwave/Hood Combo installation guides

User Manual: Kenmore 40180082010 40180082010 KENMORE MICROWAVE - Manuals and Guides View the owners manual for your KENMORE MICROWAVE #40180082010. Home:Kitchen Appliance Parts:Kenmore Parts:Kenmore MICROWAVE Manual

Open the PDF directly: View PDF .
Page Count: 24

Download
Open PDF In Browser	View PDF

Installation Instructions
Over the Ran e Microwave

Oven

BEFORE YOU BEGIN
Read these instructions
•

•

and carefully.

•

Note to Consumerfuture reference.

•

Skill level - Installation of this appliance
basic mechanical and electrical skills.

and ordinances.

•

Proper installation
installer.

Note to InstallerBe sure to leave these
instructions with the Consumer.

•

Product failure due to improper
covered under the Warranty.

IMPORTANT
local inspector's

•

completely

Save these instructions

for

use.

IMPORTANT-observe

READ CAREFULLY.

all governing

codes

KEEP THESE INSTRUCTIONS.

Keep these instructions

is the responsibility

for

requires

of the

installation

is not

,'_,

Installation Instructions

CONTENTS
General information
Important

Safety

Electrical

Requirements

Instructions

.....................

..............................

Outside

Back Exhaust .............................

Preparing
Attach

Exhaust

Damage

...........................................

- Shipment/Installation

.................

Parts

Included

Tools

You Will Need .....................................

Mounting

Space

installation

of Mounting

Plate

7
7

guide
................

8-10

Plate ...................

Determining

Wall Plate Location ...............

Aligning the Wall Plate ............................

Types

.................................

Preparation

of Top Cabinet .....................

Top Exhaust

Attach Mounting
Preparation

..............................

14-17
14

of Top Cabinet .....................

Adjust Blower ..........................................

Check Damper

........................

Oven ...........................

Adaptor ...........................

Adjust Exhaust
Connecting

b>3;_,

Oven .....................

Plate to Wall .................

Operation

Mount Microwave

?_M!,5©_,

12-13

Plate to Wall .................

Mount the Microwave

Outside

11-21

Recirculating ...........................................
Attach Mounting

Finding the Wall Studs ..............................

Installation

CiO/*

Ductwork

..............................

_, ©'©/8

'43

Plate to Wall ........... 18, 19

of Top Cabinet

Adjust Blower

.....................

....................................

Mount the Microwave

Oven ...............

19, 20
20, 21

............................................

Removing the Mounting

...............................................

Step-by-step
Placement

4, 5

Rear Wall ................................

Mounting

Preparation
Hood

18-21

Before You Use Your Microwave

.............. 22

Installation Instructions

IMPORTANT

SAFETY INSTRUCTIONS

This product requires a three-prong grounded outlet.
The installer must perform a ground continuity check
on the power outlet box before beginning the
installation to insure that the outlet box is properly
grounded. If not properly grounded, or if the outlet
box does not meet electrical requirements
noted
(under ELECTRICAL
REQUIREMENTS),
a qualified
electrician should
deficiencies.

be employed

to correct

You should have the wall receptacle and circuit
checked by a qualified electrician to make sure
the receptacle is properly grounded.

Where a standard two-prong wall receptacle is
encountered,
it is very important to have it
replaced with a properly grounded three-prong
wall receptacle, installed by a qualified
electrician.

any

CAUTION: For personal
safety, remove house fuse or
open circuit breaker before
beginning installation to
avoid severe or fatal shock

DO NOT, UNDER ANY CIRCUMSTANCES,
CUT,
DEFORM OR REMOVE ANY OF THE PRONGS
FROM THE POWER CORD. DO NOT USE WITH
AN EXTENSION
CORD.

injury.

ELECTRICAL

Product rating is 120 volts AC, 60 Hertz, 14.8 amps
and 1.7 kilowatts.

CAUTION: For personal safety, the mounting
surface must be capable of supporting the
cabinet load, in addition to the added weight of
this 59 pound product, plus additional oven loads
of up to 50 pounds or a total weight of 109

This product must be connected to a supply circuit of
the proper voltage and frequency. Wire size must
conform to the requirements of the National Electrical
Code or the prevailing local code for this kilowatt

pounds.

rating. The power supply cord and plug
brought to a separate 20 ampere branch
grounded outlet. The outlet box should
the cabinet above the microwave oven.

CAUTION: For personal safety, this product
cannot be installed in cabinet arrangements
such
as an island or a peninsula. It must be mounted to
BOTH a top cabinet AND a wall.

READ CAREFULLY.

FOR

PERSONAL SAFETY, THIS APPLIANCE
MUST BE
PROPERLY GROUNDED
TO AVOID SEVERE OR
FATAL SHOCK.

The power cord of this
appliance is equipped
with a three-prong
(grounding)
plug which
mates with a standard
three-prong
(grounding)
wall receptacle to
minimize the possibility
of electric shock hazard

Insure proper
ground exists
before use

,'_,?_M050_,I',232,

from

this appliance.

3
5Ci0/*

19_:W0

_';

_ (4/;

***_*',*,,2

2 0"0/31

'43

should be
circuit single
be located in
The outlet

box and supply circuit should be installed by a
qualified electrician and conform to the National
Electrical Code or the prevailing local code.

NOTE: For easier installation and personal
safety, it is recommended
that two people install
this product.

IMPORTANT-PLEASE

REQUIREMENTS

Installation Instructions

HOOD EXHAUST
NOTE: Read these next two pages only if you plan to vent your exhaust
recirculate the air back into the room, proceed to page 11.

OUTSIDE TOP EXHAUST (EXAMPLE

ONLY)

The following

ductwork

chart describes

an example

of one possible

DUCT PIECES

to the outside.

If you plan to

installation.

EQUIVALENT
LENGTH

NUMBER
USED

EQUIVALENT
LENGTH

Roof Cap

24 Ft.

(1)

24 Ft.

12 Ft. Straight Duct (6"
Round)

12 Ft.

(1)

12 Ft.

(1)

5 Ft.

Rectangular-to-Round
Transition
Adaptor*

5 Ft.

41 Ft.

[]

Equivalent lengths of duct pieces are based on actual
tests and reflect requirements
for good venting
performance
with any vent hood.

Total Length

* IMPORTANT:
If a rectangular-to-round
transition adaptor is used, the bottom corners of the damper
to be cut to fit, using the tin snips, in order to allow free movement of the damper.

OUTSIDE BACK EXHAUST (EXAMPLE
The following

chart describes

an example

of one possible

DUCT PIECES

Roof Cap

[

3 Ft. Straight
(3¼"x 10"
Rectangular)

)

90 ° Elbow

will have

ONLY)
ductwork

EQUIVALENT
LENGTH*

installation.

NUMBER
USED

EQUIVALENT
LENGTH

40 Ft.

(1)

4O Ft.

3Ft.

(1)

3 Ft.

(2)

2O Ft.

63 Ft.

Duct

10 Ft.

Equivalent lengths of duct pieces are based on actual
tests and reflect requirements
for good venting
performance with any vent hood.

Total Length

NOTE: For back exhaust, care should be taken to align exhaust with space between studs, or wall should be
prepared at the time it is constructed by leaving enough space between the wall studs to accommodate
exhaust.

Installation Instructions
Maximum

NOTE: If you need to install ducts, note that the total
duct length of 3W' x 10" rectangular or 6" diameter
round duct should not exceed 140 equivalent feet.
Outside

ventilation

requires

DUCT. Read the following

a HOOD

For satisfactory

EXHAUST

carefully.

Exhaust

and nothing

is blocking

airflow and are equivalent

If a round duct is required,

to a section of straight

duct

which is longer than their actual physical size. When
calculating the total duct length, add the equivalent
lengths of all transitions and adaptors plus the length
of all straight duct sections. The chart below shows
you how to calculate total equivalent ductwork length
using the approximate feet of equivalent length of
some typical ducts.

the ducts.

connection:

The hood exhaust has been designed
standard 3W'x 10" rectangular duct.

the total duct length of

Elbows, transitions,
wall and roof
caps, etc., present additional resistance to

possible. This ensures clear venting of exhaust and
helps prevent blockages. Also, make sure dampers
freely

air movement,

3W' x 10" rectangular or 6" diameter round duct
should not exceed 140 equivalent feet.

NOTE: It is important that venting be installed using
the most direct route and with as few elbows as

swing

duct length:

to mate with a

a rectangular-to-round

transition adaptor must be used. Do not use less
than a 6" diameter
duct,
DUCT PIECES

EQUIVALENT
LENGTH

NUMBER
USED

Transition Adaptor*
Rectangular-to-Round

5 Ft.

( )

Ft.

WallOap

40Ft.

( )

Ft.

90 ° Elbow

10 Ft.

( )

Ft.

45 ° Elbow

5 Ft.

( )

Ft.

90 ° Elbow

25 Ft.

( )

Ft.

45 ° Elbow

5 Ft.

( )

Ft.

Roof Cap

24 Ft.

( )

Ft.

Straight Duct 6" Round or
3W'x 10" Rectangular

1 Ft.

( )

Ft.

Total Ductwork
* IMPORTANT:
If a rectangular-toround transition adaptor is used, the
bottom corners of the damper will
have to be cut to fit, using the tin

EQUIVALENT
LENGTH

snips, in order to allow free movement

of the damper.

Equivalent lengths of duct pieces are based on actual
tests and reflect requirements for good venting
performance with any vent hood.

Installation Instructions

DAMAGE - SHIPMENT/
INSTALLATION
•

PARTS INCLUDED
HARDWARE

If the unit is damaged in shipment, return the
unit to the store in which it was bought for repair
or replacement.

•

If the unit is damaged by the customer,
or replacement is the responsibility
of the
customer.

•

If the unit is damaged by the installer
(if other
than the customer), repair or replacement
must
be made by arrangement
between customer and
installer.

PACKET

PART

repair

QUANTITY
Wood Screws
(W'x 2")

Toggle

Bolts

(and wing nuts)
(3h6" x 3")
Self-aligning
Machine Screws

(W'-28 x 3W')
Nylon Grommet

(for metal cabinets)
You will find the installation

hardware

3acket with the unit. Checkto
these parts.
NOTE:

in a

Some extra parts are included.

ADDITIONAL

PARTS

PART

QUANTITY

TOPCABINETTEMPLATE

Top Cabinet
Template

REAR WALL TEMPLATE

Rear Wall
Template

Installation
Instructions

Separately
Packed
Grease
Filters
Exhaust
adaptor

contained

make sure you have all

Installation Instructions

TOOLS YOU WILL NEED
Ruler or tape measure

Carpenter square

straight edge

# 1 and #2 Phillips screwdriver

_ H

Pencil
(optional)

Tin snips (for cutting
damper, if required)

Scissors
(to cut template, if necessary)

Gloves

Saw (saber, hole or keyhole)

Safety goggles

Electric drill with
and 5/8" drill bits

3/16",

1/2"

Filler blocks or scrap wood
pieces, if needed for top
cabinet spacing (used on
recessed bottom cabinet
installations only)

Stud finder or Hammer (optional)

Level

Duct and masking tape

MOUNTING SPACE
NOTES:
Bottom edge of
cabinet needs
to be 33" or
more from the
cooking
surface

•

The space between the cabinets must be
30" wide and free of obstructions.

•

This microwave
ranges

•

oven is for installation

up to 30" wide.

If you are going to vent your microwave
oven to the outside, see Hood Exhaust
Section for exhaust

Backsplash

•

duct preparation.

When installing the microwave oven
beneath smooth flat cabinets be careful
to follow the instructions
on the top
cabinet template for power cord
clearance.

over

Installation Instructions

1.PLACEMENT

OF THE MOUNTING PLATE

A. REMOVING THE MICROWAVE
OVEN FROM THE CARTON/
REMOVING THE MOUNTING
PLATE
1. Remove

B. FINDING THE WALL STUDS

the installation instructions, Exhaust
iWall Studs

adaptor, filters, glass tray and the small hardware
bag. Do not remove the Styrofoam 3rotecting the
front of the oven.
2, Fold back all 4 carton flaps fully against carton
sides. Then carefully roll the oven and carton over
onto the top side. The oven should be resting in
the Styrofoam.

1. Find

the studs, using one of the following
methods:
A. Stud finder-a
nails.

magnetic

device which locates

B. Use a hammer to tap lightly across the
mounting surface to find a solid sound. This
will indicate a stud location.
2. After locating the stud(s),
3. Pull the carton up and off the oven.
4, Remove

and properly

discard

Mounting

5, Remove

plastic bags.

Screws

the 2 screws

Plate

find the center by

probing the wall with a small nail to find the edges
of the stud. Then place a mark halfway between
the edges. The center of any adjacent studs
should be 16" or 24" from this mark.
3. Draw a line down the center of the studs.

from the mounting

THE MICROWAVE
MUST BE CONNECTED
LEAST ONE WALL STUD.

plate.

This plate will be used as the rear wall template
and for mounting.
NOTE: You will have to reuse two screws in original
Ioction of outcase after removing mounting plate.

TO AT

Installation Instructions
DETERMINING
Plate position

- beneath

WALL PLATE LOCATION UNDER YOUR CABINET
flat bottom

Plate position - beneath
cabinet bottom

cabinet

framed

recessed

_ '_

At least 30"

Draw a vertical line on
the wall at the center of
the 30" wide space.
Tape the Rear Wall
Template onto the wall
matching the centerline
and touching the
bottom of the cabinet.

30" to Cooktop

Draw a vertical line on the wall at the center of the
30" space.
Tape the Rear Wall Template onto the wall
matching the centerline and touching the bottom
cabinet frame.

ILmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm"l

Plate position - beneath recessed
cabinet with front overhang

Your cabinets may have decorative trim that
interferes with the microwave installation. Remove

bottom

the decorative trim to install the microwave
and to make it level.

THE MICROWAVE

properly

MUST BE LEVEL.

Use a level to make sure the cabinet

bottom is level.

If the cabinets have a front overhang only, with no
back or side frame, install the mounting plate down
the same distance as the front overhang depth. This
will keep the microwave level.
1. Measure

the inside depth of the front overhang.

2. Draw a horizontal
distance

line on the back wall an equal

below the cabinet

bottom

as the inside

depth of the front overhang.
3. For this type of installation

with front overhang

only, align the mounting tabs with this horizontal
line, not touching the cabinet bottom as described
in Step D.

Installation Instructions

D_ ALIGNING THE WALL PLATE

_zz

...............

REAR

Hole A

WALI_ TEMPLATE

Centerline
notches

Draw a Vertical Line
on Wall from Center

of Cabinet
Horizontal

Line

Area E

Hole C

Hole B

Draw a Horizontal
bottom

Horizontal

Line

line on wall from

of "Rear Wall Template".

CAUTION:
Wear gloves to avoid cutting
fingers on sharp edges.

1. Draw

a Vertical line on the wall at the center of the
NOTE: Holes A, B and C are inside area E. If none of
A, B and C is in a stud, find a stud somewhere in area
E and draw a forth circle to line up with the stud. It is
important to use at least one wood screw mounted
firmly in a stud to support the weight of the
microwave. Set the mounting
plate aside.

30" wide space.
2. Draw a Horizontal

line on the wall at the bottom of

"Rear Wall Template".
3. Drill 5/8" holes for toggle

bolts on 3 locations

(Hole A, Hole B, Hole C) but if the location of hole
is same as that of stud, drill a 3/16" hole for wood
screw. In other words, toggle bolt can not be used
to the location of stud.
NOTE: DO NOT MOUNT THE PLATE AT THIS
TIME.

Installation Instructions

2. INSTALLATION TYPES
This microwave oven is designed for adaptation
the following three types of ventilation:
A. Recirculating

(Non-Vented

B. Outside

Top Exhaust

C. Outside

Back Exhaust

(Choose A, B or C)
to

NOTE: This microwave is shipped after being
assembled for "Recirculating".
And exhaust adaptor
is shipped assembled to the filler-upper. Select the
type of ventilation required for your installation and
proceed to that section.

Ductless)

(Vertical

Duct)

(Horizontal

Duct)

A. RECIRCULATING
(NON-VENTED DUCTLESS)

B. OUTSIDE TOP EXHAUST
(VERTICAL DUCT)

Outside Top
Adaptor
Exhaust in Place for

C__OUTSIDE BACK EXHAUST
(HORIZONTAL DUCT)

Installation Instructions
A. RECIRCULATING

(Non-Vented Ductless)

INSTALLATION

OVERVIEW

A1. Attach

Plate to Wall

Mounting

A2. Prepare Top Cabinet
A3. Mount the Microwave

Oven

AI.__.ATTACH THE MOUNTING
TO THE WALL

PLATE

Place the mounting

plate against the wall and

insert the toggle wings into the holes in the wall to
mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure to coincide bottom line of the
Mounting plate with Horizontal line of "Rear wall
Template" and then the Mounting plate is properly
centered under the cabinet.
CAUTION:

Be careful to avoid pinching

between the back of the mounting

fingers

plate and the wall.

4. Tighten all bolts. Pull the plate away from the wall

- ,,,,,_

to help tighten the bolts.

A2. USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET

Attach the plate to the wall using toggle bolts. At least
one wood screw must be used to attach the plate to
a wall stud.
1, Remove

the toggle wings from the bolts.

2. Insert the bolts into the mounting

You need to drill holes for the top support screws and
a hole large enough for the cower cord to fit through.

plate through

the holes designated to go into drywall and
reattach the toggle wings to 3A" onto each bolt.

To use toggle

bolts:

Spacing for Toggles More
Than Wall Thickness
i

Mounting
Plate

Toggle Wings

Wall

•

Read the instructions
TEMPLATE.

•

Tape

•

Drill the holes, following the instructions
TOP CABINET TEMPLATE.

it underneath

on the TOP CABINET
the top cabinet.
on the

Bolt End

CAUTION: Wear safety goggles
in the cabinet bottom.

when drilling holes

Installation Instructions
MOUNT THE MICROWAVE

OVEN

especially
cabinet.

when mounting

flush

to bottom

Cabinet Front
Cabinet Bottom Shelf
Filler Block

Equivalent to
Depth of

FOR EASIER
SAFETY,
INSTALL

INSTALLATION

WE RECOMMEND
THIS MICROWAVE

IMPORTANT:
installation.

AND PERSONAL

Cabinet Recess

THAT TWO PEOPLE
OVEN.

Do not grip or use handle

igning Screw

during

Oven Top

NOTE: If your cabinet is metal, use the nylon
grommet around the power cord hole to prevent
cutting of the cord.

4. Attach the microwave

5. Insert 2 self-aligning

NOTE: We recommend using filler blocks if the
cabinet front hangs below the cabinet bottom shelf.

oven to the top cabinet.

screws

through

outer

top cabinet holes. Turn two full turns on
each screw.

IMPORTANT:
If filler blocks are not used, case
damage may occur from over tightening
screws.
NOTE: When mounting the microwave oven, thread
power cord through hole in bottom of top cabinet.
Keep it tight throughout Steps 1-3. Do not pinch cord
or lift oven by pulling cord.
1, Lift microwave, tilt it
forward, and hook slots
at back bottom edge
onto four lower tabs of
mounting plate.

6. Tighten center
screw completely.
7. Tighten the outer two screws

microwave oven. (While tightening screws, hold
the microwave oven in place against the wall and
the top cabinet.)

Rota;[e front of oven
up against
bottom

cabinet

3, Insert a self-aligning

screw through

to the top of the

top center

cabinet hole. Temporarily secure the oven by
turning the screw at least two full turns after the
threads have engaged. (It will be completely
tightened later.) Be sure to keep power cord
tight. Be careful not to pinch the cord,
8. Install grease filters.

See the Owner's

packed with the microwave.

Manual

Installation Instructions
B._,..
OUTSIDE TOP EXHAUST (Vertical Duct)
INSTALLATION

OVERVIEW

B1. Attach

Plate to Wall

Mounting

B2. Prepare
B3. Adjust

Top Cabinet
Blower

B4. Check Damper

Operation

B5. Mount Microwave
B6. Adjust

Exhaust

B7. Connect

Oven

Adaptor

Ductwork

Blm ATTACH THE MOUNTING
TO THE WALL

To use toggle bolts:

PLATE

Spacing for Toggles More
Than Wall Thickness
i

i Toggle Wings
I

Mounting
Plate _.

Wall
Bolt End

3, Place the mounting

Attach the plate to the wall using toggle bolts. At least
one wood screw must be used to attach
the plate to a wall stud.
1. Remove

NOTE: Before tightening toggle bolts and wood
screw, make sure to coincide bottom line of the
Mounting plate with Horizontal line of "Rear wall
Template" and then the Mounting plate is properly
centered under the cabinet.

the toggle wings from the bolts.

2, Insert the bolts into the mounting

plate through

plate against the wall and

insert the toggle wings into the holes in the wall to
mount the plate.

the

holes designated to go into drywall and reattach
the toggle wings to 3_,, onto each bolt.

CAUTION:
Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
4. Tighten

all bolts. Pull the plate away from the wall

to help tighten the bolts.

Installation Instructions
B3.__.
ADAPTING MICROWAVE
BLOWER FOR OUTSIDE TOP
EXHAUST

B2.__.
USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET

1. Remove

You need to drill holes for the top support screws, a
hole large enough for the power cord to fit through,
and a cutout large enough for the exhaust adaptor.

and save

2, Lift up the

screw that holds

blower plate.

blower plate to
microwave.

B_.ckof
Microwave

_°'_
Screw

3.
•

Read the instructions
TEMPLATE.

•

Tape it underneath

•

Drill the holes, following the instructions
TOP CABINET TEMPLATE.

Carefully

pull out the blower

extend far enough to allow you to adjust the
blower unit.

on the TOP CABINET

the top cabinet.

CAUTION:
Wear safety goggles
in the cabinet bottom.

unit. The wires will

on the

when drilling holes

CAUTION:
Do not touch blade of blower to prevent
cracking and breaking. Hold outer case when the
blower is removed and re-installed.
4, Roll the blower

unit 90 ° so that fan blade

openings are facing toward the top of the
microwave.

Roll

Installation Instructions
B5._,..
MOUNT THE MICROWAVE

OVEN

FOR EASIER
SAFETY,
INSTALL

5. Place the blower

IMPORTANT:
installation.

unit back into the opening.

INSTALLATION

WE RECOMMEND
THIS MICROWAVE

AND PERSONAL
THAT TWO PEOPLE
OVEN.

Do not grip or use handle

during

NOTE: If your cabinet is metal, use the nylon
grommet around the power cord hole to prevent
cutting of the cord.
NOTE: We recommend using filler blocks if the
cabinet front hangs below the cabinet bottom shelf.
IMPORTANT:
damage
CAUTION: Do not pull or stretch the blower unit
wiring. Make sure the wires are not pinched.
6, Secure

blower

unit to microwave

If filler

blocks are not used, case

may occur from

over tightening

screws.

NOTE: When mounting the microwave oven, thread
power cord through hole in bottom of top cabinet.
Keep it tight throughout Steps 1-3. Do not pinch cord
or lift oven by pulling cord.

with the screw.

1. Lift microwave,

tilt it

forward, and hook slots
at back bottom edge
onto four lower tabs of

B4. INSTALLATION PROCEDURE FOR
EXHAUST ADAPTOR AND
PROPER DAMPER OPERATION
CHECK
1. Remove and save screw

mounting

plate.

from the panel-outer

2, Rotate front of oven up
against cabinet

adaptor following

the instructions

show in diagram.
3, Make sure tape securing
damper

is removed

pivots easily before mounting

4. Lift damper
•

damper

and Re-screw

especially
cabinet.

anc

microwave

at same location

Insert a self-aligning

screw through

top center

Exhaust Ad_ 3tor and Damper is shipped
after beinc assembled to the filler-upper.

2, Slide exhaust

bottom

as (1',

You will need to make adjustments to assure
proper alignment with your house exhaust duct
after the microwave is installed.

when

mounting

flush

to bottom

Installation Instructions
B5.__.
MOUNT THE MICROWAVE

OVEN

B6_ ADJUST THE EXHAUST ADAPTOR

(cont.)

Open the top cabinet and adjust the exhaust
to connect to the house duct.

Cabinet Front
Cabinet Bottom Shelf

Blower-Plate

Filler Block

adaptor

Back of
Microwave

Damper

Depth of Cabinet
Equivalent
Recess to

Self-Aligning Screw
Adjustment, Slide the
Exhaust Adaptor as
Needed

Microwave Oven Top

4. Attach

the microwave

oven to the top cabinet.

5, Insert 2 self-aligning

screws

B7_ CONNECTING

through outer top cabinet holes.
Turn two full turns on each screw.

DUCTWORK
House Duct

6, Tighten center screw
completely.
7, Tighten the outer two screws

to the top of the

1. Extend

microwave oven. (While tightening screws, hold
the microwave oven in place against the wall and
the top cabinet.)

exhaust

adaptor.

2, Seal exhaust

it
!

8, Install grease filters. See the Owner's

the house duct down to connect

Manual

packed with the microwave.

duct joints using duct tape.

to the

Installation Instructions
C.__.
OUTSIDE BACK EXHAUST (Horizontal Duct)
INSTALLATION
01. Prepare
02. Attach

OVERVIEW

Rear Wall
Mounting

Plate to Wall

03. Prepare Top Cabinet

04. Adjust Blower
05. Mount the Microwave

Oven

C1__ PREPARING THE REAR WALL
FOR OUTSIDE BACK EXHAUST

C2._.ATTACH THE MOUNTING
TO THE WALL

PLATE

You need to cut an opening in the rear wall for outside
exhaust.

Attach the plate to the wall using toggle bolts. At least
one wood screw must be used to attach
the plate to a wall stud.
1, Remove

2.
•

Read the instructions on the REAR WALL
TEMPLATE.

•

Tape it to the rear wall.

•

Cut the opening, following
REAR WALL TEMPLATE.

the instructions

the toggle wings from the bolts.

Insert the bolts into the mounting

plate through

the holes designated to go into drywall and
reattach the toggle wings to 3_, onto each bolt.

of the

Installation Instructions
C2.__.
ATTACH THE MOUNTING
TO THE WALL (cont.)

PLATE

04_ ADAPTING MICROWAVE BLOWER
FOR OUTSIDE BACK EXHAUST

1. Remove

To use toggle bolts:

and save screw that holds blower

Plate

to microwave.
Spacing for Toggles More
Than Wall Thickness
I

Blower motor
2. Lift up the Blower

screw.

I Toggle Wings

Mounting
Plate

Plate.

Blower Motor
Back of
Microwave

Bolt End

Place the mounting

"_'_'_

plate against the wall and

3, Carefully

insert the toggle wings into the holes in the wall to
mount the plate.

pull out the blower

unit. The wires will

extend far enough to allow you to adjust the
blower unit.

End B

CAUTION:
Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
4. Tighten

Blower Motor
Screw

End l

all bolts. Pull the plate away from the wall

to help tighten the bolts.
CAUTION:
Do not touch blade of blower to prevent
cracking and breaking. Hold outer case when the
blower is removed and re-installed.

C3. USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET

4. Remove

"Parts "A" with Nipper or Scissors

You need to drill holes for the top support screws and
a hole large enough for the power cord to fit through.

Knockouts

5. Rotate blower

unit counterclockwise

Before Rotation

•

Read the instructions
TEMPLATE.

•

Tape it underneath

•

Drill the holes, following the instructions
TOP CABINET TEMPLATE.

180 °.

After Rotation

on the TOP CABINET

the top cabinet.

I
Back of
Microwave

on the

CAUTION: Wear safety goggles when drilling holes in
the cabinet bottom.

Back
of
Microwave

Installation Instructions
6.

Place the blower

MOUNT THE MICROWAVE

unit back into the opening.

OVEN

End A

End B

FOR EASIER
SAFETY,
INSTALL
CAUTION:
Do not pull or stretch the blower unit
wiring. Make sure the wires are not pinched.
NOTE: The blower unit exhaust openings
should
match exhaust openings
on rear of microwave
oven.

7, Secure

the blower unit to the microwave

INSTALLATION

WE RECOMMEND
THIS MICROWAVE

IMPORTANT:
installation.

AND PERSONAL
THAT TWO PEOPLE
OVEN.

Do not grip or use handle

during

with the

screw.

IMPORTANT:
Blower-Plate

damage

If filler

blocks

may occur from

are not used, case

over tightening

screws.

?
NOTE: When mounting the microwave oven, thread
power cord through hole in bottom of top cabinet.
Keep it tight throughout Steps 1-3. Do not pinch cord
or lift oven by pulling cord.
_

Back of
Microwave

8, Attach the exhaust

_---

Fromthe
Plate screw

adaptor

to the rear of the oven

by sliding it into the guides
back of the oven.

at the top center of the

1. Lift

microwave, tilt it
forward, and hook slot_
at back bottom edge
onto four lower tabs of
mounting plate.

Adaptor

Back of

Rotate front of oven
up against cabinet
bottom

Microwave

3, Insert a self-aligning
_I_--...__G

top center

u ide

'
Guide

screw through

From Blower motor screw
(after attached the exhaust adaptor)

Push in securely until it is in the lower locking tabs.
Take care to assure that the damper hinge is installed
so that it is at the top and that the damper swings
freely.

Installation Instructions
C5.__.
MOUNT THE MICROWAVE

OVEN

(cont.)
Install grease filters. See the Owner's
with the microwave.

Manual packed

Cabinet Front
Cabinet Bottom Shelf
Filler Block

Depth of Cabinet
Recess
quivalent to

gning Screw
Microwave Oven Top

4. Attach

the microwave

oven to the top cabinet.

5. Insert 2 self-aligning

screws

through outer top cabinet holes.
Turn two full turns on each screw.

¢
I

;ighten center
screw completely.
7, Tighten the outer two screws

to the top of the

microwave oven. (While tightening screws, hold
the microwave oven in place against the wall and
the top cabinet.)

[

8. Install grease filters. See the Owner's

Manual

packed with the microwave.

Installation Instructions

BEFORE YOU USE YOUR MICROWAVE
1. Make

sure the microwave

installed according

2, Remove
ove

oven has been

6. Read the Owner's

to instructions.

all packing material

7, KEEP INSTALLATION

from the microwave

THE LOCAL

Install turntable

4. Replace

Manual.

and ring in cavity.

house fuse or turn breaker

5, Plug power cord into a dedicated
electrical outlet.

Insure proper

back on.

20 amp

gr_oUnd
ex;sts/

INSTRUCTIONS

INSPECTOR'S

USE.

FOR

Installation Instructions

NOTE

Part No. : ??
Code No. :

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 24
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Sat Oct 20 09:04:33 2007
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Kenmore 40180082010 User Manual MICROWAVE Manuals And Guides L0709302

KENMORE Microwave/Hood Combo Manual L0709302 KENMORE Microwave/Hood Combo Owner's Manual, KENMORE Microwave/Hood Combo installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation