Kenmore Elite 30 Range Hood Black 58179 Installation Guide 58000 Series (SV07328 Rev. D)

: Kenmore Kenmore-Kenmore-Elite-30-Range-Hood-Black-58179-Installation-Guide-671562 kenmore-kenmore-elite-30-range-hood-black-58179-installation-guide-671562 kenmore pdf

Open the PDF directly: View PDF .
Page Count: 13

Use & Care / Installation Manual

Manual de Uso y Cuidado / Instalación

English / Español

SV07328 rev. D

Sears Brands Management Corporation,

Hoff man Estates, IL 60179 USA

www.kenmore.com

www.sears.com

Models / Modelos 233.5817*, 233.5818*

Kenmore Elite®

TM

Range Hood

* = color number, número de color

Campana de cocina

2

READ AND SAVE THESE INSTRUCTIONS

TABLE OF CONTENTS

Warranty .........................................................................2

Safety Instructions ..........................................................3

Operation ........................................................................4

Cleaning ...........................................................................4

Parts Included With Hood .............................................5

Parts Not Included With Hood .....................................5

Tools Needed For Hood Installation ............................5

Equivalent Duct Length Chart .......................................6

Install Ductwork ..............................................................7

Prepare The Hood Location ..........................................7

Prepare The Hood .......................................................8-10

Install The Hood .............................................................10

Connect The Wiring .......................................................11

Finalize The Installation .................................................11

Changing Light Bulbs .....................................................11

Service Parts ....................................................................12

KENMORE LIMITED WARRANTY

When this appliance is installed, operated and

maintained according to all supplied instructions,

the following warranty coverage applies. To arrange

for warranty service, call 1-800-4-MY-HOME®

(1-800-469-4663).

• For one year from the date of purchase, any

part of this product that fails due to a defect in

material or workmanship will receive free repair or

replacement if repair proves impossible. The length

of this coverage does not apply to the fi nish of any

painted or bright metal part.

• For thirty days date of purchase, any painted or

bright metal part of this product will be replaced

free of charge if its fi nish is defective in material or

workmanship.

All warranty coverage is void if this product is ever

used for other than private household purposes.

This warranty covers only defects in material and

workmanship, and will NOT pay for:

1. Consumable parts that can wear out from normal

use, including but not limited to fi lters, belts, light

bulbs, and bags.

2. A service technician to instruct the user in correct

product installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not

installed, operated or maintained according to the

all instructions supplied with the product.

5. Damage to or failure of this product resulting from

accident, abuse, misuse or use for other than its

intended purpose.

6. Damage to or failure of this product caused by the

use of detergents, cleaners, chemicals or utensils

other than those recommended in all instructions

supplied with the product.

7. Damage to or failure of parts or systems resulting from

unauthorized modifi cations made to this product.

Disclaimer of implied warranties; limitation of remedies

Customer’s sole and exclusive remedy under this

limited warranty shall be product repair as provided

herein. Implied warranties, including warranties of

merchantability or fi tness for a particular purpose,

are limited to one year or the shortest period allowed

by law. Sears shall not be liable for incidental or

consequential damages. Some states and provinces

do not allow the exclusion or limitation of incidental or

consequential damages, or limitation on the duration

of implied warranties of merchantability or fi tness, so

these exclusions or limitations may not apply to you.

This warranty gives you specifi c legal rights, and you

may also have other rights which vary from state to

state.

Sears Brands Management Corporation,

Hoff man Estates, IL 60179

3

Warranty Safety CleaningOperation Installation Service Parts

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer at the address listed in the warranty.

2. Before servicing or cleaning unit, switch power off at

service panel and lock the service disconnecting means

to prevent power from being switched on accidentally.

When the service disconnecting means cannot be

locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by

a qualifi ed person(s) in accordance with all applicable

codes and standards, including fi re-rated codes and

standards.

4. Suffi cient air is needed for proper combustion and

exhausting of gases through the fl ue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer’s guideline and safety

standards such as those published by the National

Fire Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

6. When performing installation, servicing or cleaning

the unit, it is recommended to wear safety glasses and

gloves.

7. Do not use this range hood with any additional solid

state speed control device.

8. Ducted fans must always be vented to the outdoors.

9. To reduce the risk of fi re, use only metal ductwork.

10. This unit must be grounded.

11. When applicable local regulations comprise more

restrictive installation and/or certifi cation requirements,

the aforementioned requirements prevail on those of

this document and the installer agrees to conform to

these at his own expenses.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or

when fl ambeing food (i.e.: Crêpes Suzette, Cherries

Jubilee, Peppercorn Beef Flambé).

3. Clean ventilating fans frequently. Grease should not

be allowed to accumulate on fan, fi lters or in exhaust

ducts.

4. Use proper pan size. Always use cookware appropriate

for the size of the surface element.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE

EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWING*:

1. SMOTHER FLAMES with a close-fi tting lid, cookie

sheet, or metal tray, then turn off the burner. BE

CAREFUL TO PREVENT BURNS. If the fl ames do not

go out immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or

towels - This could cause a violent steam explosion.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and

you already know how to operate it.

B. The fi re is small and contained in the area where it

started.

C. The fi re department is being called.

D. You can fi ght the fi re with your back to an exit.

*Based on “Kitchen Fire Safety Tips” published by NFPA.

CAUTION

1. For indoor use only.

2. For general ventilating use only. Do not use to exhaust

hazardous or explosive materials and vapors.

3. To avoid motor bearing damage and noisy and/or

unbalanced impellers, keep drywall spray, construction

dust, etc. off power unit.

4. Your hood motor has a thermal overload which

will automatically shut off the motor if it becomes

overheated. The motor will restart when it cools down.

If the motor continues to shut off and restart, have the

hood serviced.

5. For best capture of cooking impurities, the bottom of

the hood should be at a minimum distance of 24” and

a maximum of 30” above the cooking surface.

6. To reduce the risk of fi re and to properly exhaust air on a

ducted installation, be sure to duct air outside - Do not

exhaust air into spaces within walls or ceiling or into attics,

crawl spaces, or garage.

7. This product is equipped with a thermostat which

may start blower automatically. To reduce the risk

of injury and to prevent power from being switch on

accidentally, switch power off at service panel and

lock or tag service panel.

8. Because of the high exhausting capacity of this hood,

you should make sure enough air is entering the house

to replace exhausted air by opening a window close

to or in the kitchen.

9. Use with approved cord-connection kit only.

10. Please read specifi cation label on product for further

information and requirements.

SAFETY INSTRUCTIONS

!

INTENDED FOR DOMESTIC COOKING ONLY

!

!

READ AND SAVE THESE INSTRUCTIONS

4

Grease fi lters

The grease fi lters and the bottom panel should be cleaned

frequently. Use a warm detergent solution. Grease fi lters

are dishwasher safe.

Wash more often if your cooking style generates greater

grease - like frying foods or wok cooking.

Remove fi lters by pulling latch tabs and rotating fi lters

downward.

OPERATION OPERATION

Always turn ON your hood before you begin cooking in

order to establish an air fl ow in the kitchen. Let the blower run

for a few minutes to clear the air after you turn off the range.

This will help keep the whole kitchen cleaner and brighter.

1. Blower Auto OFF switch 4. Filter maintenance indicator

2. ON/OFF Blower speed switches 5. Nightlight switch

3. Halogen lights switch

ON/OFF Blower speed switches

Press the switch corresponding to the desired blower speed.

The light over the switch indicates the selected speed (from 1

for low speed to 4 for high speed). To turn off the blower,

press once more on the corresponding blower speed switch.

NOTE: When speed 1 is chosen, the blower will operate

at high speed for less than one second and then

revert back to speed 1. This operation is normal

and is designed for optimal blower performance.

HEAT SENTRY™

Your hood is equipped with a HEAT SENTRY thermostat.

This thermostat is a device that will turn on or speed up the

blower if it senses excessive heat above the cooking surface.

The light indicator over speed 3 switch will quickly fl ash.

1) If blower is OFF - it turns blower ON to speed 3.

2) If blower is ON at a lower (or higher) speed setting - it

turns blower to speed 3.

When the temperature level drops to normal, the blower

will return to its original setting and the light indicator

over speed 3 switch will stop fl ashing.

Halogen lights switch

This switch provides 3 diff erent lighting levels, according

to your needs. The lighting intensity changes by increments

of 1 (e.g.: Press once for low intensity, once again to get

more, up to three times). From the higher intensity, press

once again to shut off the lights.

Uses 120 Volts, 50 W, MR 16 with GU10 base or PAR 16

with GU10 base, shielded halogen bulbs (included).

WARNING: The HEAT SENTRY thermostat can

start the blower even if the hood is turned OFF. If

this occurs, press the speed 3 switch until its light

indicator stops fl ashing if you must stop the blower.

Hood Cleaning

Stainless steel cleaning:

How to maintain its “BRIGHT LOOK”

Do:

- Regularly wash surfaces with clean cloth or rag soaked

with warm water and mild soap or liquid dish detergent.

- Always clean in the direction of original polish lines.

- Always rinse well with clear water (2 or 3 times) after

cleaning. Wipe dry completely.

- You may also use a specialized household stainless steel

cleaner.

Do not:

- Use any steel or stainless steel wool or any other

scrapers to remove stubborn dirt.

- Use any harsh or abrasive cleaners.

- Allow dirt to accumulate.

- Let plaster dust or any other construction residues

reach the hood. During construction/renovation, cover

the hood to make sure no dust sticks to stainless steel

surface.

Avoid when choosing a detergent:

- Any cleaners that contains bleach will attack stainless

steel.

- Any products containing: chloride, fl uoride, iodide,

bromide will deteriorate surfaces rapidly.

- Any combustible products used for cleaning such

as acetone, alcohol, ether, benzol, etc., are highly

explosive and should not be used close to a range.

Enamel Finish:

Clean with warm water and mild detergent only. If

discoloration occurs, use a good enamel polish such as

automotive polish. (DO NOT use rough abrasive cleaner

or porcelain cleaner).

Auto OFF switch

When a speed is selected, press the Auto OFF switch to

activate the delay function. The corresponding speed

indicator LED will start fl ashing to indicate this function is

activated. The fan will continue to operate for 5 minutes

and will stop automatically. To cancel the delay function,

press the Auto OFF switch once again; the blower will then

work in normal mode.

NOTE: The blower speed can be increased - or decreased -

during Delay mode without starting another

5-minute cycle.

15234

WARNING: In order to prevent the risk of

personal injury, do not install a lamp identifi ed

for use only in enclosed fi xtures.

Filter maintenance indicator

After 24 hours of operation, the fi lter maintenance light

indicator will start blinking. This indicates the fi lters need

to be cleaned in order to maintain effi cient operation of

the unit. The indicator light will blink until the function is

reset by pressing the nightlight switch for 3 seconds.

CLEANING

Nigthlight switch

Press this switch once to turn on the nightlight. Press this

switch once more to shut off the nightlight.

HC0049

5

Parts Bag including:

1 Wire Clamp LP16-AP

2 Wire Connectors no. 74B

5 no. 8 x 1/2” Screws

3 no. 6 x 1/2” Screws

Grease Filter

(2 per hood)

HR0043

HR0044

HR0045

HR0047

HR0048

HR0049

HR0050

HR0051

Screwdriver

(Robertson or

Phillips)

Pencil Tape

Measure

Drill Sabre

Saw Keyhole

Saw

-or-

Duct Tape

Wire

Stripper

TOOLS NEEDED FOR HOOD INSTALLATION

HR0041

120 V, 50 W, MR16 with GU10 base or PAR 16

with GU10 base, shielded halogen lamps

(4 per hood). Sears Part No. SV05921

HR0012

3¼” x 10”

Adapter/Damper

HR0010

HR0011

Warranty Safety CleaningOperation Installation Service Parts

Ducting Accessories are not included with hood.

(See “Equivalent Duct Length Chart” on page 6 for Ducting

Accessory Model Nos.)

PARTS INCLUDED WITH HOOD PARTS NOT INCLUDED WITH HOOD

NOTE

Before proceeding to the installation, check the contents

of the box. If items are missing or damaged, contact the

manufacturer.

6

EQUIVALENT DUCT LENGTH CHART

HJ0049

HA0086

HA0085

HJ0050

Broan Model 406

Straight Duct

6” round x 2’ long

Equivalent length

2 ft.

Broan Model 415

7” Round Elbow

Equivalent length

10 ft.

Sears Model 59581

3¼” x 10” to 6”

Round Transition

Equivalent length

5.5 ft.

Sears Model 59691

6” Round Wall Cap

Equivalent length

34 ft.

(6 ft. w/o damper)

Sears

Model 59091

Roof Cap

(accepts 7” round

or 3¼” x 10” duct)

Equivalent length

30 ft.

(7 ft. w/o damper)

Kenmore range hoods are designed to perform effi ciently when attached to long runs of duct. As a point of reference,

this hood will function at approximately 80% of its rated air performance when 100 equivalent feet of 7” round

ductwork is attached. Use this chart to calculate the equivalent duct length of your system.

HJ0050

Broan Model 407

Straight Duct

7” round x 2’ long

Equivalent length

2 ft.

HJ0049

Broan Model 419

6” Round Elbow

Equivalent length

8 ft.

Broan Model 412H

3¼” x 10” to 7”

Round Transition

Equivalent length

5.5 ft.

Broan Model 428

3¼” x 10”

Right-angle Elbow

Equivalent length

8.5 ft.

Broan Model 429

3¼” x 10”

Right-angle

Flat Elbow

Equivalent length

24 ft.

Broan Model 430

3¼” x 10”

Right-angle

Short Eave Elbow

Equivalent length

15 ft.

Sears Model 59391

3¼” x 10” Wall Cap

Equivalent length

45 ft.

(7 ft. w/o damper)

HJ0048 Broan Model 401

Straight Duct

3¼” x 10” x 2’ long

Equivalent length

2 ft.

HJ0056

HJ0057

HJ0058

HJ0059

HJ0060

HJ0061

Broan Model 431

3¼” x 10”

Right-angle

Long Eave Elbow

Equivalent length

15 ft.

HA0085

HA0037

Broan Model 647

7” Round Wall Cap

Equivalent length

34 ft.

(6 ft. w/o damper)

Sears Model “Ducting Accessories” available by calling Sears at:

1-800-4-MY-HOME®

Broan Model “Ducting Accessories” available by calling Broan at:

1-800-558-1711

7

Warranty Safety CleaningOperation Installation Service Parts

1. Plan where and how the ductwork will be located.

Install proper-sized ductwork, transition(s), elbow(s), and roof or wall cap. For best results, use a minimum number

of transitions and elbows. Use 2’’ metal foil duct tape to seal duct joints.

The minimum hood distance above cooktop must not be less than 24’’. A maximum of 30’’ above cooktop is

highly recommended for best capture of cooking impurities.

Distances over 30’’ are at the installer and users discretion.

INSTALL DUCTWORK

INSTALLATION WITH

RECTANGULAR DUCT

Hood

3¼” x 10” duct

Roof cap

Wall

cap

HH0056A

24” minimum above

cooking surface

Hood

Roof cap

Wall

cap

HH0057A

24” minimum above

cooking surface

6” OR 7”

round duct

Transition

3¼” x 10” to 6” OR

3¼” x 10” to 7”

INSTALLATION WITH

ROUND DUCT

PREPARE THE HOOD LOCATION

1. If the bottom of the cabinet is recessed, attach three

1” wide wood strips (not included), as shown beside, in

order to properly attach the hood to the cabinet. The

wood strips must be as thick as the recess.

HD0026A

CABINET BOTTOM

1¾”1¾”

10⅛’’

1”

1”

1”

2. Cut-out the openings for duct (A) and power cable (B), in cabinet or wall, according to the direction or discharge

chosen. See fi gures below.

C

L

HD0162A

3½”

5¼” 2¾”

B

1½” dia.

A

5/16” 5¼”

7/8”

C

L

3/4”

4”

5¼” 5¼” 2”

HD0163A

A

CABINET BOTTOM

1½” 2”

1½”

B

HORIZONTAL DISCHARGE VERTICAL DISCHARGE

8

PREPARE THE HOOD

1. Punch-out the knock-out for the chosen opening (horizontal at the back or vertical on top of the hood) and for

electrical connection.

HD0164

2. Pull latch tab and remove both fi lters from the hood.

HD0166

3. Remove the 5 screws retaining the bottom panel to the

hood and set aside. Pull out the bottom panel by the

front part.

HD0167

SCREW

LOCATIONS

HORIZONTAL DISCHARGEVERTICAL DISCHARGE

HD0165

9

5. To remove side panel, hold it

near the front of the hood and

slide in the same direction as

the small arrow (A) in order to

disengage it.

PREPARE THE HOOD

HO0079

6. Then lift the front of the side

panel.

A

HO0080

HO0081

7. Pull out the side panel tabs (B)

from the hood and remove the

side panel.

B

4. Unplug both light connectors mounted on each side panels.

See picture beside.

HE0075

Warranty Safety CleaningOperation Installation Service Parts

10

8. Using 2 no. 6 x 1/2’’ screws, assemble the adapter/damper to the hood.

NOTE: Damper fl ap pivot (1) to the front of the hood for vertical discharge and for horizontal discharge,

damper fl ap pivot to top of hood.

9. Seal the adapter/damper to the hood using duct tape.

PREPARE THE HOOD

HO0082

1

HO0083

HO0084

1

HO0085

1. Run power cable to installation location. Position the hood in its intended location. Using a pen, mark the position

of the screws (smaller part of the keyhole, see picture below for the 5 keyhole locations). Remove the hood.

Install 4 no. 8 x 1/2’’ screws, leaving a 1/8’’ gap. Do not install the no. 5 screw yet.

INSTALL THE HOOD

HD0168

1

23

4

5

2. Attach the wire clamp, insert the power cable in the hood and tighten the wire clamp to secure the cable. Place the

hood under the cabinet and slide it in position. Make sure the adapter/damper assembly enters the duct opening.

Tighten the 4 screws completely, then add the last screw (screw no. 5) in the center keyhole. Make sure the damper

fl ap opens freely.

HORIZONTAL DISCHARGEVERTICAL DISCHARGE

11

CAUTION: Remove protective plastic fi lm covering fi lters before installing them.

!

WARNING: Risk of electrical shock. Electrical wiring must be done by qualifi ed personnel in accordance

with all applicable codes and standards. Before connecting wires, switch power off at service panel and

lock service disconnecting means to prevent power from being switched on accidentally.

1. Connect cable using provided wire connectors.

Connect BLACK to BLACK, WHITE to WHITE and

GREEN or bare wire under GREEN ground screw.

DO NOT FORGET TO CONNECT THE GROUND.

CONNECT THE WIRING

FINALIZE THE INSTALLATION

1. Reinstall both side panels. DO NOT FORGET TO PLUG BACK THE LIGHT CONNECTORS!

2. Reinstall bottom panel using 5 screws from Step 3 of “Prepare The Hood’’ Section.

HE0059

3. Reinstall both fi lters.

This hood requires 120 V, 50 W, MR16 type, GU10 shielded halogen lamps (included).

CHANGING LIGHT BULBS

Refer to page 12 for ordering information.

HE0076

WARNING: Do not touch lamps during or soon after operation. Burns may occur. In order to prevent the risk

of personal injury, only install shielded halogen lamps. Also, never install a cool beam, a dichroïc lamp, a

lamp not suitable for use in recessed luminaires or identifi ed for use in enclosed fi xtures.

!

1. To remove lamps, gently push upwards and turn

counterclockwise to disengage bulb leads from their

grooves.

2. Install the new lamps by placing the bulb leads into

their grooves in the socket and gently push upwards

and turn clockwise until secure.

HE0077

Warranty Safety CleaningOperation Installation Service Parts

12

SERVICE PARTS

HL0064

1

2

3

5

6

7

8

9

4

10

KEY NO. PART NO. DESCRIPTION 30’’ WIDTH 36’’ WIDTH

1 SV13296 Adapter/Damper 1 1

2SV16571 Electronic Control Module, Black (including Overlay, item 3) 1 1

SV16572 Electronic Control Module, White (including Overlay, item 3) 1 1

3SV07322 Overlay Black 1 1

SV07323 Overlay White 1 1

4 SV16569 Lamp Shell, Socket & Trim Ass’y 4 4

5 SV05921 Halogen Lamp (50 W, 120 V, PAR 16, GU-10) 4 4

6 SV01766E Motor (including Wheel, item 7) 1 1

7 SV06111 Wheel 1 1

8SV07332 Filters with latch, square pressed, 9.92” x 17.98” x 0.35” 2 1

SV07333 Filters with latch, square pressed, 12.92” x 17.98” x 0.35” 1 2

9 SV07325 Transformer 1 1

10 SV02160 Capacitor 1 1

* SV09428 Kenmore Elite Logo 1 1

* SV07326 Harness 1 1

* SV07328 Kenmore Elite Installation Manual 1 1

* SV06751 Installation Bag: 1 Wire Clamp LP16-AP, 2 Wire Connectors no. 74B,

5 no. 8 x 1/2” Screws, 3 no. 6 x 1/2” Screws 11

Order replacement parts by PART NO., not by

KEY NO.

*Not illustrated.

REPLACEMENT PARTS AND REPAIRS

In order to ensure your unit remains in good

working condition, you must use the manufacturer

genuine replacement parts only. The manufacturer

genuine replacement parts are specially designed

for each unit and are manufactured to comply

with all the applicable certifi cation standards

and maintain a high standard of safety. Any third

party replacement part used may cause serious

damage and drastically reduce the performance

level of your unit, which will result in premature

failing. The manufacturer recommends to contact

a certifi ed service depot for all replacement parts

and repairs.

® Registered Trademark / TM Trademark of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries

® Marca Registrada / TM Marca de Fábrica de KCD IP, LLC en Estados Unidos, o Sears Brands, LLC in otros países

MC Marque de commerce / MD Marque déposée de Sears Brands, LLC

Get it fixed, at your home or ours!

Your Home

For troubleshooting, product manuals and expert advice:

www.managemylife.com

For repair – in your home – of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner’s manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1-800-4-MY-HOME®(1-800-469-4663)

Call anytime, day or night (U.S.A. and Canada)

www.sears.com www.sears.ca

Our Home

For repair of carry-in items like vacuums, lawn equipment,

and electronics, call anytime for the location of your nearest

Sears Parts & Repair Service Center

1-800-488-1222 (U.S.A.) 1-800-469-4663 (Canada)

www.sears.com www.sears.ca

To purchase a protection agreement on a product serviced by Sears:

1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)

Para pedir servicio de reparación

a domicilio, y para ordenar piezas:

1-888-SU-HOGAR®

(1-888-784-6427)

www.sears.com

Au Canada pour service en français:

1-800-LE-FOYERMC

(1-800-533-6937)

www.sears.ca