Kenwood USA 31103110 Non-Broadcast Transmitter (VHF FM Repeater) User Manual TKR 750 850 E

Download:
Mirror Download [FCC.gov]
Document ID	116743
Application ID	q9TI6KNiPZHASVuSUV8USw==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	1.6kB (20014 bits)
Date Submitted	2000-09-12 00:00:00
Date Available	2001-03-06 00:00:00
Creation Date	2000-07-14 11:40:47
Producing Software	Acrobat Distiller 3.01 for Power Macintosh
Document Lastmod	0000-00-00 00:00:00
Document Title	TKR-750/850 (E)
Document Creator	Adobe PageMaker 6.0
Document Author:	MURRY

VHF FM REPEATER/ UHF FM REPEATER
TKR-750/ TKR-850
KENWOOD CORPORATION
INSTRUCTION MANUAL
THANK YOU!
We are grateful you purchased this KENWOOD repeater.
We believe this easy-to-program repeater will be highly
effective in your communications system, and will keep
personnel operating at peak efficiency.
KENWOOD incorporates the latest in advanced
technology into all of our products. As a result, we feel
strongly that you will be pleased with the quality and
features of this product.
© B62-1327-00 (K)
09 08 07 06 05 04 03 02 01 00
NOTICES TO THE USER
FCC WARNING
This equipment generates or uses radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless
the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an unauthorized
change or modification is made.
◆
GOVERNMENT LAW PROHIBITS THE OPERATION OF
UNLICENSED RADIO TRANSMITTERS WITHIN THE
TERRITORIES UNDER GOVERNMENT CONTROL.
ILLEGAL OPERATION IS PUNISHABLE BY FINE OR
IMPRISONMENT OR BOTH.
REFER SERVICE TO QUALIFIED TECHNICIANS ONLY.
FEATURES
◆
•
You can easily program channel data using the KPG-66D
software on a PC.
◆
•
You can recall 1 of 16 preset channels using either a PF key or
the external control line.
UNPACKING AND CHECKING EQUIPMENT
•
The firmware can be written to the Flash memory through an
external source.
Note: The following unpacking information is for use by your KENWOOD
dealer, an authorized KENWOOD service facility, or the factory.
•
QT/DQT signalling can be programmed on each channel. It
simultaneously decodes up to 16 different QT/DQT tones.
•
When using the KPG-66D, RX PLL lock voltage, RX input signal
strength, TX PLL lock voltage, TX output power, and the power
supply voltage can be monitored on a PC.
•
The interface port can be used with external equipment, such
as a repeater controller.
Carefully unpack the repeater. We recommend that you
identify the items listed in the following table before
discarding the packing material. If any items are missing
or have been damaged during shipment, file a claim with
the carrier immediately.
•
The repeater has multi-mode capability.
Wide: 30 kHz, 25 kHz/ Narrow: 15 kHz,12.5 kHz (TKR-750)
Wide: 25 kHz/
Narrow: 12.5 kHz
(TKR-850)
•
You can adjust the following functions from a PC:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
CW ID Deviation
DQT Deviation
Maximum Deviation
QT Deviation
Remote TA
Repeat Gain Level
TX Power
RX Audio Signal Output (RA)
RX Detector Signal Output (RD)
Signalling Balance
Signalling Deviation (SD)
Squelch (Analog/ RSSI)
Test Tone Deviation
TX Audio Input (TA)
Voting Tone Level
PRECAUTIONS
•
Do not expose the unit to rain or moisture; to prevent fire or
electric shock.
•
Do not open the unit under any circumstances; to avoid risk of
electric shock.
•
Do not expose the unit to long periods of direct sunlight, nor
place it close to heating appliances.
•
Do not place the unit in excessively dusty and/or humid areas,
nor on unstable surfaces.
•
If you detect an abnormal odor or smoke coming from the unit,
disconnect the power from the unit immediately. Contact your
KENWOOD service center or dealer.
Item
Hardware fixture
Front glass
Filter
Cushion
Cushion
Foot
Foot
Grommet
Handle
Screws
DC cord
Fuse
Warranty card
Instruction manual
Part Number
Quantity
J21-8402-X4
B10-2636-X4
B11-1259-X4
G13-1801-X4
G13-1802-X4
J02-0475-X5
J02-0492-X4
J59-0302-X5
K01-0425-X5
N35-2606-45
E30-3427-X5
F05-1537-X5
——
B62-1327-XX
INSTALLATION
To install the handles onto the front panel of the repeater,
align the handles with the holes on the front panel, then
secure the handles using the supplied screws.
Please consult your dealer for installing the repeater and
antenna.
MICROPHONE
Connect an optional KMC-27A, KMC-27B, or KMC-9C
KENWOOD microphone to the MICROPHONE jack on
the front panel.
CONTROLS AND FUNCTIONS
■ Front Panel
q Speaker
w Display
Two, 7-segment digits display the channel number
or status.
e VOLUME control
Turn clockwise until a click sounds, to unmute the
volume. Rotate to adjust the volume. Turn
counterclockwise fully to mute the volume.
r Power switch
y MICROPHONE jack
Connect a microphone to this 8-pin modular jack.
u Programmable Function keys
Press these keys to activate their programmable
functions.
i BUSY indicator
Lights green while a signal is being received.
o TX (transmit) indicator
Lights red while transmitting.
t POWER indicator
Lights green when power is applied from the DC
jack. Lights red when power is applied from the
BACKUP battery terminal.
■ Rear Panel
q RX IN jack
Connect a RX antenna or a duplexer to this BNC
receptacle.
t CONTROL I/O jack
Connect an external programming device or
repeater controller to this DB-25 interface.
w FUSE
Insert a 6 A blade fuse into this fuse holder.
y TEST/SPKR jack
Test input/output jack. Connect an external
speaker to this jack.
e DC 13.8V jack
Connect a 13.6 V DC power supply to this jack.
r BACKUP battery terminal
REPEATER OPERA TION
Note: Please consult your dealer for programming the repeater.
When power is applied to the unit, the POWER indicator
lights green.
Turn the VOLUME control clockwise until a click sounds,
to unmute the volume. Rotate to adjust the volume. Turn
the VOLUME control counterclockwise fully to mute the
volume.
The BUSY indicator lights green while receiving a signal,
and the TX indicator lights red while transmitting.
u TX OUT jack
Connect a TX antenna or a duplexer to this BNC
receptacle.
TRANSCEIVER OPERA TION
■ Receive
Adjust the volume to your desired level. You may
need to readjust the volume when you receive a
message from your dispatcher or another member in
your fleet.
• The BUSY indicator lights while a signal is being
received.
■ Transmit
1 Listen to the channel before transmitting, to make
sure it is not being used.
2 Press the microphone PTT switch and speak in
your normal speaking voice.
• FCC regulations require that you identify the
station you are calling as well as your own
station (your assigned call sign).
• The TX indicator lights while transmitting.
3 When you finish speaking, release the PTT switch.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 2
Create Date                     : 2000:07:14 11:40:47
Producer                        : Acrobat Distiller 3.01 for Power Macintosh
Subject                         : 
Creator                         : Adobe PageMaker 6.0
Title                           : TKR-750/850 (E)
Author                          : MURRY

EXIF Metadata provided by EXIF.tools