Kenwood USA 31113120 Single Channel Mode User Manual TKR 750 850 E
Kenwood USA Corporation Single Channel Mode TKR 750 850 E
manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 124717 |
| Application ID | 7Rsfpmx2vB3ASqbH7+MoOA== |
| Document Description | manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 1.6kB (20014 bits) |
| Date Submitted | 2000-11-09 00:00:00 |
| Date Available | 2000-11-07 00:00:00 |
| Creation Date | 2000-07-14 11:40:47 |
| Producing Software | Acrobat Distiller 3.01 for Power Macintosh |
| Document Lastmod | 0000-00-00 00:00:00 |
| Document Title | TKR-750/850 (E) |
| Document Creator | Adobe PageMaker 6.0 |
| Document Author: | MURRY |
VHF FM REPEATER/ UHF FM REPEATER TKR-750/ TKR-850 KENWOOD CORPORATION INSTRUCTION MANUAL THANK YOU! We are grateful you purchased this KENWOOD repeater. We believe this easy-to-program repeater will be highly effective in your communications system, and will keep personnel operating at peak efficiency. KENWOOD incorporates the latest in advanced technology into all of our products. As a result, we feel strongly that you will be pleased with the quality and features of this product. © B62-1327-00 (K) 09 08 07 06 05 04 03 02 01 00 NOTICES TO THE USER FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. ◆ GOVERNMENT LAW PROHIBITS THE OPERATION OF UNLICENSED RADIO TRANSMITTERS WITHIN THE TERRITORIES UNDER GOVERNMENT CONTROL. ILLEGAL OPERATION IS PUNISHABLE BY FINE OR IMPRISONMENT OR BOTH. REFER SERVICE TO QUALIFIED TECHNICIANS ONLY. FEATURES ◆ • You can easily program channel data using the KPG-66D software on a PC. ◆ • You can recall 1 of 16 preset channels using either a PF key or the external control line. UNPACKING AND CHECKING EQUIPMENT • The firmware can be written to the Flash memory through an external source. Note: The following unpacking information is for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. • QT/DQT signalling can be programmed on each channel. It simultaneously decodes up to 16 different QT/DQT tones. • When using the KPG-66D, RX PLL lock voltage, RX input signal strength, TX PLL lock voltage, TX output power, and the power supply voltage can be monitored on a PC. • The interface port can be used with external equipment, such as a repeater controller. Carefully unpack the repeater. We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the carrier immediately. • The repeater has multi-mode capability. Wide: 30 kHz, 25 kHz/ Narrow: 15 kHz,12.5 kHz (TKR-750) Wide: 25 kHz/ Narrow: 12.5 kHz (TKR-850) • You can adjust the following functions from a PC: • • • • • • • • • • • • • • • CW ID Deviation DQT Deviation Maximum Deviation QT Deviation Remote TA Repeat Gain Level TX Power RX Audio Signal Output (RA) RX Detector Signal Output (RD) Signalling Balance Signalling Deviation (SD) Squelch (Analog/ RSSI) Test Tone Deviation TX Audio Input (TA) Voting Tone Level PRECAUTIONS • Do not expose the unit to rain or moisture; to prevent fire or electric shock. • Do not open the unit under any circumstances; to avoid risk of electric shock. • Do not expose the unit to long periods of direct sunlight, nor place it close to heating appliances. • Do not place the unit in excessively dusty and/or humid areas, nor on unstable surfaces. • If you detect an abnormal odor or smoke coming from the unit, disconnect the power from the unit immediately. Contact your KENWOOD service center or dealer. Item Hardware fixture Front glass Filter Cushion Cushion Foot Foot Grommet Handle Screws DC cord Fuse Warranty card Instruction manual Part Number Quantity J21-8402-X4 B10-2636-X4 B11-1259-X4 G13-1801-X4 G13-1802-X4 J02-0475-X5 J02-0492-X4 J59-0302-X5 K01-0425-X5 N35-2606-45 E30-3427-X5 F05-1537-X5 —— B62-1327-XX INSTALLATION To install the handles onto the front panel of the repeater, align the handles with the holes on the front panel, then secure the handles using the supplied screws. Please consult your dealer for installing the repeater and antenna. MICROPHONE Connect an optional KMC-27A, KMC-27B, or KMC-9C KENWOOD microphone to the MICROPHONE jack on the front panel. CONTROLS AND FUNCTIONS ■ Front Panel q Speaker w Display Two, 7-segment digits display the channel number or status. e VOLUME control Turn clockwise until a click sounds, to unmute the volume. Rotate to adjust the volume. Turn counterclockwise fully to mute the volume. r Power switch y MICROPHONE jack Connect a microphone to this 8-pin modular jack. u Programmable Function keys Press these keys to activate their programmable functions. i BUSY indicator Lights green while a signal is being received. o TX (transmit) indicator Lights red while transmitting. t POWER indicator Lights green when power is applied from the DC jack. Lights red when power is applied from the BACKUP battery terminal. ■ Rear Panel q RX IN jack Connect a RX antenna or a duplexer to this BNC receptacle. t CONTROL I/O jack Connect an external programming device or repeater controller to this DB-25 interface. w FUSE Insert a 6 A blade fuse into this fuse holder. y TEST/SPKR jack Test input/output jack. Connect an external speaker to this jack. e DC 13.8V jack Connect a 13.6 V DC power supply to this jack. r BACKUP battery terminal REPEATER OPERA TION Note: Please consult your dealer for programming the repeater. When power is applied to the unit, the POWER indicator lights green. Turn the VOLUME control clockwise until a click sounds, to unmute the volume. Rotate to adjust the volume. Turn the VOLUME control counterclockwise fully to mute the volume. The BUSY indicator lights green while receiving a signal, and the TX indicator lights red while transmitting. u TX OUT jack Connect a TX antenna or a duplexer to this BNC receptacle. TRANSCEIVER OPERA TION ■ Receive Adjust the volume to your desired level. You may need to readjust the volume when you receive a message from your dispatcher or another member in your fleet. • The BUSY indicator lights while a signal is being received. ■ Transmit 1 Listen to the channel before transmitting, to make sure it is not being used. 2 Press the microphone PTT switch and speak in your normal speaking voice. • FCC regulations require that you identify the station you are calling as well as your own station (your assigned call sign). • The TX indicator lights while transmitting. 3 When you finish speaking, release the PTT switch.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 2 Create Date : 2000:07:14 11:40:47 Producer : Acrobat Distiller 3.01 for Power Macintosh Subject : Creator : Adobe PageMaker 6.0 Title : TKR-750/850 (E) Author : MURRYEXIF Metadata provided by EXIF.tools