Kenwood USA 378501 UHF FM Handheld/Portable/Mobile Transceiver User Manual Part 1

Download:
Mirror Download [FCC.gov]
Document ID	1008365
Application ID	Kk13tHCLcTwMK11WItsx1A==
Document Description	User Manual Part 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	26.13kB (326612 bits)
Date Submitted	2008-09-29 00:00:00
Date Available	2008-09-30 00:00:00
Creation Date	2008-05-26 11:40:19
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2008-05-26 11:42:28
Document Title	Microsoft Word - NX-300-K2_-K4_TK-5320-K2_-K4_Instruction_Manual_1.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	163097

NX-300-K2, NX-300-K4, TK-5320-K2, TK-5320-K4
FCC ID: ALH378501
IC: 282D-378501
INSTRUCTION MANUAL
NX-300
THANK YOU!
We are grateful you chose KENWOOD for your land mobile radio applications. We believe this easy-to-use transceiver
will provide dependable communications to keep personnel operating at peak efficiency.
KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be
pleased with the quality and features of this product.
NOTICES TO THE USER
WARNING:
‹ GOVERNMENT LAW PROHIBITS THE OPERATION OF UNLICENSED RADIO TRANSMITTERS WITHIN THE
TERRITORIES UNDER GOVERNMENT CONTROL.
‹ ILLEGAL OPERATION IS PUNISHABLE BY FINE OR IMPRISONMENT OR BOTH.
‹ REFER SERVICE TO QUALIFIED TECHNICIANS ONLY.
‹ DO NOT OPERATE YOUR TRANSCEIVER IN EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, ETC.).
‹ TURN OFF YOUR TRANSCEIVER WHILE TAKING ON FUEL, OR WHILE PARKED IN GASOLINE SERVICE
STATIONS.
SAFETY:
It is important that the operator is aware of and understands hazards common to the operation of any transceiver.
WARNING:
EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.)
Turn off your transceiver while taking on fuel, or while parked in gasoline service stations.
One or more of the following statements may be applicable:
FCC WARNING
This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause
harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the
authority to operate this equipment if an unauthorized change or modification is made.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
· Consult the dealer for technical assistance.
NX-300-K2, NX-300-K4, TK-5320-K2, TK-5320-K4
FCC ID: ALH378501
IC: 282D-378501
ATTENTION (U.S.A. Only):
The RBRC Recycle seal found on KENWOOD nickel-cadmium (Ni-Cd) battery packs
indicates KENWOOD’s voluntary participation in an industry program to collect and
recycle Ni-Cd batteries after their operating life has expired. The RBRC program is an
alternative to disposing Ni-Cd batteries with your regular refuse or in municipal waste
streams, which is illegal in some areas.
For information on Ni-Cd battery recycling in your area, call (toll free)
1-800-8-BATTERY (1-800-822-8837). KENWOOD’s involvement in this program is
part of our commitment to preserve our environment and conserve our natural
resources.
UNPACKING AND CHECKING EQUIPMENT
Note:
The following unpacking instructions are for use by your
KENWOOD dealer, an authorized KENWOOD service facility, or the factory.
Carefully unpack the transceiver. We recommend that you identify the items listed in the following table before
discarding the packing material. If any items are missing or have been damaged during shipment, file a claim with the
carrier immediately.
§ Accessories
Item
Belt Clip
Part Number
Quantity
K2
J29 - 0730 -*5
Screw
N30 - 3008 - 60
Cap
B09 - 0717 - *3
Screw
N08 - 0564 - *4
NX-300-K2, NX-300-K4, TK-5320-K2, TK-5320-K4
FCC ID: ALH378501
IC: 282D-378501
Installing/ Removing the Optional Battery Pack PREPARATION
The battery pack is not charged at the factory; charge it before use.
CAUTION:
‹ DO NOT RECHARGE THE BATTERY PACK IF IT IS ALREADY FULLY CHARGED. DOING SO MAY CAUSE
HE LIFE OF THE BATTERY PACK TO SHORTEN OR THE BATTERY PACK MAY BE DAMAGED.
‹ AFTER RECHARGING THE BATTERY PACK, DISCONNECT IT FROM THE CHARGER. IF THE CHARGER
POWER IS RESET (TURNED ON AFTER BEING TURNED OFF), RECHARGING WILL START AGAIN AND
THE BATTERY PACK WILL BECOME OVERCHARGED.
‹ DO NOT SHORT THE BATTERY TERMINALS OR DISPOSE OF THE BATTERY BY FIRE.
‹ NEVER ATTEMPT TO REMOVE THE CASING FROM THE BATTERY PACK.
1 Match the guides of the battery pack with the corresponding grooves on the upper rear of the transceiver, then firmly
press the battery pack t
2 Flip the safety catch into place to prevent accidentally pressing the release latch and removing the battery.
3 To remove the battery pack, lift the safety catch, press the release latch,then pull the battery pack away from the
transceiver.
NX-300-K2, NX-300-K4, TK-5320-K2, TK-5320-K4
FCC ID: ALH378501
IC: 282D-378501
Installing the Antenna
Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and
turning it clockwise until secure.
Installing the Belt Clip
If necessary, attach the belt clip using the two supplied 3 x 6 mm screws.
Notes: If the belt clip is not installed, its mounting location may get hot during continuous transmission or when left sitting
in a hot environment.
NX-300-K2, NX-300-K4, TK-5320-K2, TK-5320-K4
FCC ID: ALH378501
IC: 282D-378501
Installing the Cap over the Speaker/Microphone Jacks
If you are not using an optional KMC-25 speaker/ microphone, install the cover over the univeral connector using the
supplied 4 x 6 mm screw.
Installing the Optional Speaker/ Microphone
1 Insert the guide of the speaker/ microphone connector into the groove of the universalconnector.
2 Secure the connecter in place using the attached screw.
NX-300-K2, NX-300-K4, TK-5320-K2, TK-5320-K4
FCC ID: ALH378501
IC: 282D-378501
GETTING ACQUAINTED
Knob
NO.
Name
Lock/
Non Lock
Description
Power switch/
Volume control
Lock/
Non Lock
Power SW
(CCW:Power OFF)
Audio Volume adjuster
Selector Knob
Lock
Programmable
default : CH/GID Select
Switch
Selector Knob
Power switch/
Volume control
PTT
Side 1
Side 2
Fig. 1 Left Side
Fig.2 Front

NO.
Name
AUX(Orange)
Lock/
Non Lock
Non Lock
Description
Programmable
default: No Function

NO.
Name
Lock/
Non Lock
Description
PTT
Non Lock
TX ON/OFF
Side 1
Non Lock
Programmable
default: Squelch off momentary
Side 2
Non Lock
Programmable
default: Backlight
NX-300-K2, NX-300-K4, TK-5320-K2, TK-5320-K4
FCC ID: ALH378501
IC: 282D-378501

NO.
Name
Description
U1
Programmable
default: Zone Up
D1
Programmable
default: NoneZone Down
P1
Programmable
default: None
P2
Programmable
default: CH/GID Up
P3
P4
Programmable
Programmable
default: None
default: None
LED
NO.
Name
Description
The LED is three colors.
Lights green while receiving at user mode. Light red while transmitting,
flashes red when the battery power is low .Lights orange when
individual called.
LED
TERMINAL
Universal connector
Universal connector covering for blindfold mode of resin is possible.
NO.
Name
Description
Impedance
I/O
High Impedance
SSW
Ext/Int Speaker Switch Input
SP+
BTL Output + for External Speaker
8 ohm
SP-
BTL Output - for External Speaker
16 ohm
MSW
Ext/Int MIC Switch Input
High Impedance
EMC
External MIC Input
1.8 k ohm
ME
External MIC GND
GND
PTT
External PTT Input
High Impedance
PF
Programable Function Key Input
High Impedance
OPT
Man Down Input
High Impedance
10
GND
GND
11
5U
5V
5V
12
TXD
Serial Data Output
CMOS
13
RXD
Serial Data Input
CMOS
--
14 NC
Reserve
Antenna Terminal
Impedance is 50 ohm
Battery Terminal
It’s type of spring plate. The minus terminal connect to chassis ground
It’s mounted rear side of radio and mounting instruction is slide method.
OTHER
Rear
A rail and a hook for battery installation.
Space which affixes name plate.Model name plate
Screw hole for belt hook installation.
Bottom
Battery release lever
NX-300-K2, NX-300-K4, TK-5320-K2, TK-5320-K4
FCC ID: ALH378501
IC: 282D-378501
Appearance
Appearance with KNB-47L/48L
NX-300-K2, NX-300-K4, TK-5320-K2, TK-5320-K4
FCC ID: ALH378501
IC: 282D-378501
OPERATING BASICSATING BASICS
§ Switching Power ON/OFF
Turn the Power switch/ Volume control clockwise to switch the transceiver ON.
Turn the Power switch/ Volume control counterclockwise to switch the transceiver OFF.
§ Adjusting the Volume
Rotate the Power switch/ Volume control to adjust the volume.
§ Selecting a Channel
Pressing [] to select a channel.
Pressing [C>] increases the channel number and pressing [
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2008:05:26 11:42:28+09:00
Create Date                     : 2008:05:26 11:40:19+09:00
Metadata Date                   : 2008:05:26 11:42:28+09:00
Format                          : application/pdf
Title                           : Microsoft Word - NX-300-K2_-K4_TK-5320-K2_-K4_Instruction_Manual_1.doc
Creator                         : 163097
Document ID                     : uuid:a3b79620-3e16-4376-a371-7a935bca8928
Instance ID                     : uuid:6c6a3515-9d01-4759-b233-3dab4204dada
Page Count                      : 10
Author                          : 163097

EXIF Metadata provided by EXIF.tools