Kenwood Excelon Ddx8019 Users Manual DDX8019_B54 4532 00_00_eng

DDX8039 to the manual 9ea597ea-c7a0-ad14-cdbc-ceb4943f5687

: Kenwood Kenwood-Excelon-Ddx8019-Users-Manual-262935 kenwood-excelon-ddx8019-users-manual-262935 kenwood pdf

Open the PDF directly: View PDF .
Page Count: 12

Download
Open PDF In Browser	View PDF

MONITOR WITH DVD RECEIVER

DDX8019
DDX8039
INSTALLATION MANUAL

© B54-4532-00/00 (KV/RV)

DDX8019_B54-4532-00_00_eng.indd 1

07.2.7 1:43:03 PM

Accessories
1
..........1
2
..........1
3
..........2
4
..........1
5
..........1
6
..........6
7
..........6
8
..........1

2 |

DDX8019/DDX8039

DDX8019_B54-4532-00_00_eng.indd 2

07.2.7 1:43:04 PM

Installation Procedure
1. To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.

2WARNING
• If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
• Do not cut out the fuse from the ignition wire (red) and the
battery wire (yellow). The power supply must be connected
to the wires via the fuse.

¤
• If the power is not turned ON (or it is ON, but will be OFF
immediately), the speaker wire may have a short-circuit
or touched the chasis of the vehicle and the protection
function may have been activated. Therefore, the speaker
wire should be checked.
• If your car’s ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and off with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
• If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
• If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
• Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
• Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
• When only two speakers are being connected to the
system, connect the connectors either to both the front
output terminals or to both the rear output terminals (do
not mix front and rear). For example, if you connect the +
connector of the left speaker to a front output terminal, do
not connect the - connector to a rear output terminal.
• After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
• Mount the unit so that the mounting angle is 30° or less.
• This unit has the cooling fan (page 5) to decrease the
internal temperature. Do not mount the unit in a place
where the cooling fan of the unit are blocked. Blocking
these openings will inhibit the cooling of the internal
temperature and result in malfunction.

English |

DDX8019_B54-4532-00_00_eng.indd 3

3

07.2.7 1:43:06 PM

Connection

If you connect the ignition wire (red) and the battery
wire (yellow) to the car chassis (ground), you may
cause a short circuit, that in turn may start a fire. Always
connect those wires to the power source running
through the fuse box.

Ignition key
switch
ACC

A
B

Car fuse box
Car fuse box
(Main fuse)

A

Ignition wire (Red)

B

Battery wire (Yellow)

C
+

–

FUSE ( 5A )

Ground wire (Black) (To car chassis)

C

Antenna Cord

Battery
Connect to the vehicle's parking brake
detection switch harness using the
supplied relay connector.
Parking sensor wire (Light Green)
PRK SW

For the sake of safety, be sure to connect the parking sensor.

To vehicle's reverse lamp harness

Reveres sensor wire (Purple/White)

Dimmer control wire (Orange/White)
To car light control switch

To steering remote
Connect to the terminal that is grounded when either
the telephone rings or during conversation.

Steering remote control input (Light Blue/Yellow)
Mute wire (Brown)

To connect the Kenwood navigation system,
consult your navigation manual.
Depending on what antenna you are using,
connect either to the control terminal of the motor antenna, or to the
power terminal for the booster amplifier of the film-type antenna.
When using the optional power amplifier,
connect to its power control terminal.
To "EXT.AMP.CONT." terminal of the amplifier
having the external amp control function.

Motor antenna control wire (Blue)

Power control wire (Blue/White)
External amplifier control wire (Pink/Black)

If no connections are made, do not let the cable come out from the tab.

4 |

DDX8019/DDX8039

DDX8019_B54-4532-00_00_eng.indd 4

07.2.7 1:43:06 PM

Rear view

FUSE ( 10A )

Cooling fan

FM/AM
antenna input
Accessory 1

ILLUMI

FRONT L

REVERSE

White/Black
White

FRONT R

REMO.CONT

REAR L

Gray

REAR R

+

To front right speaker

Green/Black
Green

P CONT

To front left speaker

Gray/Black

MUTE

ANT. CONT

+

+

To rear left speaker

Purple/Black
Purple +

To rear right speaker

EXT.CONT

English |

DDX8019_B54-4532-00_00_eng.indd 5

5

07.2.7 2:07:53 PM

System Connection
USB terminal (iPod)
USB terminal

USB device
(commercially available)
USB device
(commercially available)

iPod

RELAY 1

RELAY 2

Do not connect.

To Relay Box

Accessory 2

iPod
iPod
VIDEO IN AUDIO IN

AV OUT

SUB
WOOFER

REAR

FRONT

REAR VIEW
CAMERA

AV IN1

AV OUT

AV IN2

Rear view

6 |

■ Audio/Visual input2
• Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
■ Audio/Visual Output
• Visual output (Yellow)
■ Audio/Visual input1
• Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
■ Rear View Camera Input
• Visual input (Yellow)
■ Front Preout
• Audio left output (White)
• Audio right output (Red)
■ Rear Preout
• Audio left output (White)
• Audio right output (Red)
■ Subwoofer Preout
• Audio left output (White)
• Audio right output (Red)
■ Audio/Visual Output
• Audio left output (White)
• Audio right output (Red)
■ Audio Input (iPod)
Resistance-free stereo type mini
plug (3.5φ)
■ Visual Input (iPod)
Resistance-free mini plug (3.5φ)

DDX8019/DDX8039

DDX8019_B54-4532-00_00_eng.indd 6

07.2.7 1:43:08 PM

Optional Accessory Connection

iPod
(commercially available)

Navigation System
(Optional Accessory)

KCA-iP300V
(Optional Accessory)

Audio Input
iPod
AUDIO IN

Audio Output
(Black)

Connection cable
(Included in the Navigation System)

Visual Input
iPod
VIDEO IN

Visual Output
(Yellow)

Rear view
USB terminal

iPod

USB terminal (iPod)
USB terminal

iPod cannot be connected.

Connection cable
(Included in the Disc changer)

Disc Changer etc.
(Optional Accessory)

TV ANTENNA INPUT
TO MONITOR UNIT

TV Tuner
(Optional Accessory)
Connection cable
(Included in the TV tuner)

English |

DDX8019_B54-4532-00_00_eng.indd 7

7

07.2.7 1:43:08 PM

Installing the Escutcheon
For General Motors
1. Cut out accessory 4 to meet the shape of
the opening of the center console.
2. Attach accessory 4 to the unit.

Cut out to meet the shape of
the opening in the vehicle.

Accessory 4

For Volkswagen
1. Attach accessory 8 to the unit.

Accessory 8

8 |

DDX8019/DDX8039

DDX8019_B54-4532-00_00_eng.indd 8

07.2.7 1:43:09 PM

For Toyota/Scion
1. Cut out accessory 4 as illustrated.

Cutting line

Accessory 4

2. Fold double-sided adhesive (accessory
5) along the slit and attach it to
accessory 4 cut-out against the
center rib as illustrated. Use 2 pieces
of accessory 5 for 1 accessory 4 cutout.
3. Attach accessory 4 cut-out to the unit.

Accessory 5

English |

DDX8019_B54-4532-00_00_eng.indd 9

9

07.2.7 1:43:10 PM

Installation for Monitor/Player Unit

Firewall or metal support

Screw (M4X8)
(commercially available)

Bend the tabs of the mounting
sleeve with a screwdriver or similar
utensil and attach it in place.
Self-tapping screw
(commercially available)

Metal mounting strap
(commercially available)

Make sure that the unit is installed securely in place. If the unit is unstable,
it may malfunction (eg, the sound may skip).

Installation on Toyota, Nissan or Mitsubishi Car using Brackets
Accessory 6 (M5x6mm)
or Accessory 7 (M5x7mm)

Car Bracket

Accessory 6 (M5x6mm)
or Accessory 7 (M5x7mm)

10 |

DDX8019/DDX8039

DDX8019_B54-4532-00_00_eng.indd 10

07.2.7 1:43:11 PM

Removing Monitor/Player Unit
Removing the Hard Rubber Frame
(escutcheon)
1. Engage the catch pins on the removal tool 3 and
remove the two locks on the lower level.
Lower the frame and pull it forward as shown in
the figure.
Accessory 3

Removing the Unit
1. Remove the hard rubber frame by referring to the
removal procedure in the section .
2. Remove the Hex-head screw with integral washer
(M4 × 8) on the back panel.
3. Insert the two removal tools 3 deeply into the
slots on each side, as shown.
Accessory 3

Catch
Lock

⁄
• The frame can be removed from the top side in the same
manner.

2. When the lower level is removed, remove the
upper two locations.

4. Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.

⁄
• Be careful to avoid injury from the catch pins on the
removal tool.

5. Pull the unit all the way out with your hands, being
careful not to drop it.

English |

DDX8019_B54-4532-00_00_eng.indd 11

11

07.2.7 1:43:11 PM

DDX8019_B54-4532-00_00_eng.indd 12

07.2.7 1:43:12 PM



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 7.0 for Macintosh
Modify Date                     : 2007:02:19 17:14:30+09:00
Creator Tool                    : InDesign: pictwpstops filter 1.0
Create Date                     : 2007:02:07 13:43:17+09:00
Metadata Date                   : 2007:02:19 17:14:30+09:00
Format                          : application/pdf
Creator                         : onoguchi
Title                           : DDX8019_B54-4532-00_00_eng.indd
Document ID                     : uuid:bf991020-b665-11db-9551-000d9350f0a0
Instance ID                     : uuid:fb5275c0-f562-4daa-bb5a-4066e8d83317
Page Count                      : 12
Author                          : onoguchi

EXIF Metadata provided by EXIF.tools