Kenxen Electronic BU4001 IP-CAM User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2584100
Application ID	2CXLwzLij2L9XCclLgM7BQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	117.32kB (1466496 bits)
Date Submitted	2015-04-15 00:00:00
Date Available	2015-05-30 00:00:00
Creation Date	2015-03-27 11:44:44
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2015-03-30 10:02:27
Document Title	User Manual
Document Creator	Adobe InDesign CC 2014 (Macintosh)

Sunlight Damage: Do not leave the Products
in direct sunlight for more than several hours
at a time. Exposure to direct sunlight can damage the Products.
These warnings are periodically updated for
completeness. Check www.getmyfox.com/
warnings/ for the latest version.
In the event you have any question or problem with your Myfox Product, please contact
our support on www.getmyfox.com/support/
FCC Statement
This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment
off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the
equipment and receiver
• Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected
• Consult the dealer or an experienced
radio/television technician for help
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter should
be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body and must not be collocated or
operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.
Warning
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
IC Statement
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation
is subject to the following two conditions: (1)
this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause undesired operation of the device.
This class B digital apparatus complies with
Canadian ICES-003.
Cet appareil est conforme à la norme RSS-210
d’Industrie Canada et aux réglementations de
la FCC. Son utilisation est soumise aux deux
conditions suivantes : (1) cet appareil ne doit
pas provoquer d’interférence nuisible et (2)
cet appareil doit être capable de recevoir
différentes interférences, y compris les interférences susceptibles de provoquer un dysfonctionnement.
Cet appareil numérique de classe B est
conforme à la norme NMB-003 du Canada.
WEEE
The directive on Waste Electrical and Electronic Equipment (WEEE), which entered into
force as European law on 13th February 2003,
resulted in a major change in the treatment
of electrical equipment at end-of-life. The
purpose of this Directive is, as a first priority,
the prevention of WEEE, and in addition, to
promote the reuse, recycling and other forms
of recovery of such wastes so as to reduce
disposal.
The WEEE logo (shown at the left)
on the product or its box indicates
that this product must not be disposed of or dumped with your other
household waste.
You are liable to dispose of all your electronic or electrical waste equipment by relocating over to the specified collection point for
recycling of such hazardous waste. Isolated
collection and proper recovery of your electronic and electrical waste equipment at the
time of disposal will allow us to help conserve
natural resources. Moreover, proper recycling
of the electronic and electrical waste equipment will ensure safety of human health and
the environment. For more information about
electronic and electrical waste equipment disposal, recovery, and collection points, please
contact your local city centre, household
waste disposal service, shop from where you
purchased the equipment, or manufacturer of
the equipment.
ROHS
This product is in compliance with Directive
2011/65/EU of the European Parliament and
of the Council of 8 June 2011, on the restriction of the use of certain hazardous substances in electrical and electronic equipment.
EU Declaration of conformity
Myfox hereby declares that this equipment is
in compliance with the essential requirements
and other relevant provisions of Directive
1999/5/EC, ErP 2009/125/EC Directive and
RoHS 2011/65/EU Directive. The declaration
of conformity may be consulted in the support section of our Web site, accessible from
www.getmyfox.com/legal/
BU4001 - User Manual v1.0. - February 24th, 2015
© 2014, Myfox, All rights reserved
iPad, iPhone and iPod Touch are trademarks
of Apple Inc.
LEGAL NOTICE
3Volets113x113Camera23032015OKVecto.indd 1-3
23/03/2015 19:13
3Volets113x113Camera23032015OKVecto.indd 5-6
23/03/2015 19:13
MYFOX PRODUCT & SERVICES WARRANTY
& SAFETY WARNINGS
These Myfox Product & Services Warranty
and Safety Warnings set forth certain legal
terms applicable to your use of the products
and services provided by Myfox SAS or any of
its subsidiaries, parents, and affiliates for EU
customer and Myfox Inc. or any of its subsidiaries, parents, and affiliates for US and Canada customers (“Myfox”).
The terms below form one part of the master
commercial agreement between you (“Customer” or “you”) and Myfox (the “Master
Agreement”), which includes the following
(each, a “Myfox Agreement”), found at www.
getmyfox.com/legal/:
• Myfox Sales Terms & Conditions
Agreement
• Myfox Hardware, Applications, and
Embedded Software Agreement
• Myfox Services Agreement
• Myfox Product & Services Warranty
and Safety Warnings
• Myfox Additional Terms Applicable to
Specific Territories
By establishing an account with Myfox or purchasing or using a Myfox Product or Myfox
Services, you agree to be bound by all terms
of the Master Agreement and any Sub-Agreement that are applicable in the territory where
you are located. Myfox retains the right to modify and change the Master Agreement or any
of the Sub-Agreements, subject to applicable
law, and your continued use of the Myfox Product and/or Myfox Services indicates your
continued acceptance of the Master Agreement and/or the applicable Sub-Agreement.
For the avoidance of doubt, the Myfox Pro-
duct & Services Warranty and Safety Warnings incorporate and are subject to the
Myfox Master Agreement, and also includes
and incorporate by reference the Requirements for Proper Use of the Myfox Products.
MYFOX LIMITED WARRANTY
Myfox («Seller») warrants that all Seller hardware («Hardware”) will be free of material
defects in materials and workmanship (the
«Warranty») for a period of two (2) years from
the date of purchase («Warranty Period»).
Third party products packaged or shipped
with the Hardware are not covered by this
Warranty, and are instead covered by the warranty provided by their manufacturer, if any.
You must provide Seller with an invoice
addressed to you or other valid proof of
purchase for your Product in order to be covered under this Warranty, and it is your responsibility to retain such proof. Except where
prohibited by applicable law, the Warranty is
nontransferable and is limited to the original
purchaser. The Warranty gives you specific legal rights, and you may also have other rights
that vary under local laws.
In order to receive Warranty service, you must
submit a claim to Seller by contacting Seller’s
warranty hotline at www.getmyfox.com/support/. If Seller determines that you and the
Hardware are covered by this Warranty, you
will be provided an RMA authorization number and further instructions you must follow
to obtain Warranty service or replacement
Hardware.
This Warranty does not apply to any Hardware that has been misused, abused, disassembled, or altered, as determined in Seller’s
sole discretion upon Seller’s inspection of the
Hardware. In addition, this Warranty shall not
cover: (a) any Hardware whose serial or batch number has been damaged, amended or
erased, (b) damage caused by breach of the
installation or maintenance instructions provided by Seller, (c) failures linked to the power
supply, or (d) Hardware with a microprocessor
showing signs of impact, overvoltage, or even
slight overheating. If Seller determines in its
sole discretion that any defect in material or
workmanship has occurred during the applicable Warranty Period in any of the Hardware,
your sole and exclusive remedy shall be repair
or replacement of the defective Hardware at
Seller’s option.
Seller reserves the right to clarify, amend,
restate or otherwise modify the terms of the
Warranty in its sole discretion. Prior to submitting a Warranty claim, Seller recommends you
visit the support section at www.getmyfox.
com for technical support.
EXCEPT AS SPECIFICALLY PROVIDED IN
THIS WARRANTY, SELLER DISCLAIMS ALL
OTHER EXPRESS OR IMPLIED WARRANTIES
OF ANY KIND RELATING TO THE HARDWARE, INCLUDING WITHOUT LIMITATION
WARRANTIES OF TITLE OR IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE, TO THE FULLEST EXTENT
PERMITTED UNDER APPLICABLE LAW.
TO THE FULLEST EXTENT PERMITTED BY
ANY APPLICABLE LAW, SELLER HEREBY
DISCLAIMS ALL LIABILITY FOR ANY DAMAGES OR INJURY WHATSOEVER CAUSED
BY OR RELATED TO USE OF, OR INABILITY
TO USE, THE HARDWARE UNDER ANY
CAUSE OR ACTION WHATSOEVER OF ANY
JURISDICTION, INCLUDING, WITHOUT LIMITATION, ACTIONS FOR BREACH OF WARRANTY, BREACH OF CONTRACT OR TORT
(INCLUDING NEGLIGENCE) AND SELLER
SHALL NOT BE LIABLE FOR ANY INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY OR
CONSEQUENTIAL DAMAGES, INCLUDING
FOR LOSS OF PROFITS, GOODWILL OR
DATA, IN ANY WAY WHATSOEVER ARISING
OUT OF THE USE OF, OR INABILITY TO USE,
THE HARDWARE.
WHEN YOU INSTALL, SET UP, OR USE THE
HARDWARE, YOU ARE GIVEN THE OPPORTUNITY TO ALTER DEFAULTS OR CHOOSE
PARTICULAR SETTINGS. THE CHOICES YOU
MAKE CAN LEAD TO NON- RECOMMENDED
OPERATION OF THE HARDWARE AND/OR
YOUR OTHER EQUIPMENT. YOU ASSUME
ALL LIABILITY FOR ANY LOSS OR OTHER
DAMAGE OR LIABILITY RELATING TO YOUR
FAILURE TO MEET THE REQUIREMENTS FOR
PROPER USE OF THE PRODUCTS AND YOUR
CHOICE OF PARTICULAR SETTINGS AND SELECTION OR ADJUSTMENT DEFAULTS.
MYFOX WARNINGS
Please ensure that you read the warnings
below before using the products provided
by Myfox, including without limitation Myfox
Home Alarm, Myfox Security Camera, and
Myfox HC2 (the “Products”).
Limitations of the Products: The Products are
not constantly monitored by Myfox personnel and are inherently subject to failure for a
variety of reasons, including insufficient WiFi
signal, third party service outages, and others.
The Products are not a lifesaving solution for
people or property at risk in the home, and
are no substitute for a monitored emergency
notification and response system or trained
emergency response professionals.
Before Using the System: Read and follow
all setup and operating instructions provided
with the Products, and test the Products after
setup to make sure they are functioning properly. Failure to follow all instructions relating
to the Products may compromise their effectiveness.
WiFi and radio Interference: The Products
are only effective if your home WiFi network
functions properly and the radio connections
between the Products are working properly.
The size, thickness, and materials of the walls,
wallpaper, and other materials in your home
or the surrounding environment can interfere
with wireless signals and affect the range and
functioning of the Products.
Children: This product should not be used by
children under the age of 13.
Alarm Sound: Sound at high volumes can
cause irreparable damage to your hearing.
Do not stand close to the Products while the
alarm is sounding.
Usage Environment: Do not use the Products
outside unless the user manual indicates the
Product may be used outdoors. Do not place
the Products in humid areas or other areas
where the Products are likely to get wet, such
as a bathroom, as the Products may be damaged by moisture. Outdoor use of Products
that are not designed to function outdoors
may damage the Products and impair the
functioning of the Product, as well as the functioning of any system of which the Product is
a part.
Radio Frequency Interference: The Products
can emit radio waves that can affect the operation of nearby electronics, including cardiac
pacemakers. If you have a pacemaker or other
implanted medical device, do not use the
headset without first consulting your doctor
or the manufacturer of your medical device.
Electrical Shock:
To reduce risk of electric shock:
• Do not modify or disassemble any of
the components provided
• Do not use the Product if any cable is
damaged or any wires are exposed
• Use only the types of batteries specified
in the manual, and do not use any
batteries that appear to be damaged
If a power adapter is provided:
• Do not expose the power adapter to
water or moisture
• Unplug the power adapter before
cleaning, and clean only with a dry cloth
• Keep the power adapter away from open
flames and other heat sources
• Use only the power adapter provided
with the Product

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2015:03:27 11:44:44+01:00
Creator                         : Adobe InDesign CC 2014 (Macintosh)
Modify Date                     : 2015:03:30 10:02:27+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2015:03:30 10:02:27+08:00
Creator Tool                    : Adobe InDesign CC 2014 (Macintosh)
Instance ID                     : uuid:817e7d22-06bd-44ae-899b-80a5253e1538
Original Document ID            : xmp.did:aaefcdab-ff5a-410d-bc33-bba63ebc4ab6
Document ID                     : xmp.id:30a58a6a-334d-4081-ab8a-f43f118590b3
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:6d8f3b5d-dd29-4911-942a-02541386856f
Derived From Document ID        : xmp.did:6d8f3b5d-dd29-4911-942a-02541386856f
Derived From Original Document ID: xmp.did:aaefcdab-ff5a-410d-bc33-bba63ebc4ab6
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2014 (Macintosh)
History Changed                 : /
History When                    : 2015:03:27 11:44:44+01:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 11.0
Trapped                         : False
Page Count                      : 4

EXIF Metadata provided by EXIF.tools