Keri Systems Isolation Relay H IRP 1 Installation Guide

User Manual: Keri Systems IRP-1 Isolation Relay Installation Guide Installation Guide

Open the PDF directly: View PDF PDF.
Page Count: 4

IRP-1 Isolation Relay
Installation Guide
Page 1 of 4 P/N: 01833-001 Rev. H
1.0 Purpose
Keri controllers are designed with built-in voltage transient suppression. The controller ship kits also provide external
transorbs that Keri recommends installing. For most applications, this level of protection is more than adequate. However,
there are certain applications that can require additional protection. Typically these are:
1. Magnetic locks and similar devices
2. Dry-contact devices for use with heavy-duty solenoids such as turnstiles, vehicle gates, and overhead doors
For these applications, the IRP-1 should be used to isolate the controller from the transients these devices can generate,
ensuring reliable protection and operation of the controller.
2.0 Kit Contents
The IRP-1 kit is made up of the following items:
• One relay PCB
• One transorb (1.5KE39C nonpolarized)
• Double sticky-sided foam tape (for PCB mounting)
3.0 Specifications
The isolation relay is rated at 12 A max @ 28 VDC.
4.0 Wiring Diagrams
This document provides generic drawings for wiring to an external locking device (such as a magnetic lock or door strike)
and to a dry-contact device (such as a switch or relay controlling a motor for a parking barrier or power gate). Please refer
back to the Installation Guide for the Keri controller you are installing to determine the specific Terminal Blocks and Pins
to which these wiring connections are made.
There are two wiring paths shown from the external lock to the N/O and N/C connections: one for a Fail-Secure device
and one for a Fail-Safe device. Review the drawing and ensure you are making the correct connection for your
application.
NOTE Install the supplied transorb as near to the external locking device or dry-contact device as possible. Do not install
the transorb if the device is being powered with greater than 12 VDC.
IRP-1 Isolation Relay
Installation Guide
Page 2 of 4 P/N: 01833-001 Rev. H
4.1 Wiring to an External Locking Device
N/O N/C
COM
–+
IRP-1
–+
12 VDC
Controller Power Supply
–+
12 VDC
Lock Power Supply
Keri Controller
Connection for a
Fail-Safe Device
Connection for a
Fail-Secure Device
Controller Power
Ground
NO / Lock
Common
NC / Lock
Other Pins
Relay Terminal Block
Power Terminal Block
External
Lock
Device
Transorb
IRP-1 Isolation Relay
Installation Guide
Page 3 of 4 P/N: 01833-001 Rev. H
4.2 Wiring to a Dry Contact Device
N/O N/C
COM
–+
IRP-1
–+
12 VDC
Controller Power Supply
Keri Controller
Connection for a
Fail-Safe Device
Connection for a
Fail-Secure Device
Controller Power
Ground
NO / Lock
Common
NC / Lock
Other Pins
Relay Terminal Block
Power Terminal Block
Dry
Contact
Device
Transorb
IRP-1 Isolation Relay
Installation Guide
Page 4 of 4 P/N: 01833-001 Rev. H
5.0 Contact Keri Systems
end of document
Keri USA Keri UK, Ireland, Europe
2305 Bering Drive
San Jose, CA 95131 Unit 17
Park Farm Industrial Estate
Ermine Street
Buntingford
Herts SG9 9AZ UK
Telephone: (800) 260-5265
(408) 435-8400 Telephone: + 44 (0) 1763 273 243
Fax: (408) 577-1792 Fax: + 44 (0) 1763 274 106
Web: www.kerisys.com Web: www.kerisystems.co.uk
E-mail: sales@kerisys.com
techsupport@kerisys.com E-mail: sales@kerisystems.co.uk
tech-support@kerisystems.co.uk

Navigation menu