Keurig K 10 Mini Plus Brewer User Guide

: Keurig Keurig-K-10-Mini-Plus-Brewer-User-Guide-643832 keurig-k-10-mini-plus-brewer-user-guide-643832 keurig pdf

Open the PDF directly: View PDF .
Page Count: 11

Owner’s manual

Keurig® K-Cup™ K10 MINI Plus Brewer

2 3

CAUTION: There are two sharp needles that puncture the

K-Cup® pack, one above the K-Cup® Pack Holder and the

other in the bottom of the K-Cup® Pack Holder. To avoid risk

of injury, do not put your fingers in the K-Cup® Pack

Assembly Housing.

CAUTION: There is extremely hot water in the K-Cup® Pack Holder during

the brew process. To avoid risk of injury, do not lift the Handle or open the

K-Cup® Pack Assembly Housing during the brewing process.

CAUTION: Please always keep the brewer in its upright position to avoid

potential injury and/or damage to your brewer.

SHORT CORD INSTRUCTIONS: A short power supply cord is provided to

reduce the risk of becoming entangled in or tripping over a longer cord.

If an extension cord is used, (1) the marked electrical rating of the cord set or

extension cord should be at least as great as the electrical rating of the

appliance; (2) the cord should be arranged so that it will not drape over the

countertop or tabletop where it can be pulled on by children or tripped over

unintentionally; and (3) the extension cord must include a 3-prong grounding plug.

THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.

IMPORTANT SAFEGUARDS Safe Operation & Use

WARNING WARNING: TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT REMOVE THE

BOTTOM COVER. NO USER SERVICEABLE

PARTS ARE INSIDE. REPAIR SHOULD BE DONE

BY AUTHORIZED SERVICE PERSONNEL ONLY.

RISK OF FIRE OR

ELECTRIC SHOCK

DO NOT OPEN !

WARNING KEEP ALL PLASTIC BAgS AwAY FROM CHILDREN.

WARNING THIS PRODUCT CONTAINS CHEMICALS, INCLUDINg

LEAD, wHICH IS KNOwN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,

BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.

WARNING TO USERS AND PARENTS

1. DO NOT permit children to use brewer unless there is adult

supervision. Brewer dispenses very hot water.

2. SPECIAL NOTICE FOR HOT COCOA USERS:

IMMEDIATELY AFTER USING A HOT COCOA K-CUP® PACK, RUN a Hot

Water Brew Cycle without a K-Cup® pack to avoid the possibility of

clogging the exit needle. DO NOT assume the next user will do this.

When using electrical appliances, basic

safety precautions should be followed,

including the following:

1. Read all instructions before using.

2. Do not touch hot surfaces. Use handles

and knobs when available.

3. This appliance must be properly

installed and located in accordance

with these instructions before it is used.

4. The use of accessory attachments

not recommended by the appliance

manufacturer may result in fire,

electrical shock or injury to persons.

5. Do not place on or near a hot gas or

electric burner, or in a heated oven.

6. Do not use outdoors.

7. To protect against fire, electric shock

and injury do not immerse cords, plugs,

or the appliance in water or any other

liquid.

8. Do not overfill the Cold Water Reservoir

with water.

9. Use only water in this appliance! Do

not put any other liquids or foods in the

Water Reservoir except as instructed in

the Cleaning Instructions in this guide.

10. Turn off and unplug the brewer before

cleaning or maintenance. Allow to cool

before putting on or taking off parts

and before cleaning the appliance.

11. For best operation, plug the appliance

into its own electrical outlet on a

dedicated circuit to prevent flickering

of lights, blowing of fuses or tripping a

circuit breaker.

12. Do not operate any appliance with a

damaged cord or plug or after

the appliance malfunctions or is

damaged in any manner. Contact

Keurig Customer Service to report

any malfunction of or damage to the

brewer.

13. Do not let the cord hang over the edge

of the table or counter, or touch hot

surfaces.

14. To disconnect, press the Power Button

on the brewer to “OFF” status and then

remove the plug from the wall outlet.

15. Close supervision is necessary when

any appliance is used by or near

children.

16. Do not lift the brewer Handle while

brewing is in progress; scalding

may occur.

17. Always keep the Cold Water Reservoir

Lid closed unless you are refilling it.

18. This appliance is equipped with a power

cord having a grounding wire with a

grounding plug. The appliance must

be grounded using a 3-hole properly

grounded outlet. In the event of an

electrical short circuit, grounding

reduces the risk of electrical shock.

19. If the outlet is a standard 2-prong wall

outlet, it is your personal responsibility

and obligation to have it replaced with a

properly grounded 3-prong wall outlet.

20. Do not, under any circumstances, cut or

remove the third (ground) prong from

the power cord or use an adapter.

21. Consult a qualified electrician if

the grounding instructions are not

completely understood, or if doubt

exists as to whether the appliance is

properly grounded.

22. Do not use the appliance for other than

its intended use.

SAVE THESE

INSTRUCTIONS.

4 5

TABLE OF CONTENTS

KEURIG® GOURMET SINGLE CUP HOME BREWING SYSTEM

K10 MINI Plus Brewer — Using Your Brewer

SECTION 1—Brewer Overview ..........................................................4

SECTION 2 —Helpful Hints .................................................................6

SECTION 3—Buttons & Indicators .........................................................7

SECTION 4—Set-Up & Operation

Initial Cleansing & First Brew ...........................................................8

SECTION 5—Cleaning & Maintenance

Cleaning External Parts .................................................................. 12

Cleaning the K-Cup® Pack Holder Assembly .............................. 12

Cleaning the Cold Water Reservoir ................................................14

Emptying the Internal Hot Water Tank ........................................... 14

De-Scaling Your Brewer ..................................................................14

Storage ...............................................................................................15

Storing the Power Cord .................................................................... 15

SECTION 6—Troubleshooting .......................................................... 16

SECTION 7—Warranty ...................................................................... 18

Record your Brewer Serial Number here.

Removing the serial number label from the brewer will void warranty.

SECTION 1 Brewer Overview

For replacement parts, please visit www.keurig.com

Water Level Guide

Handle

K-Cup® Pack Holder Assembly

K-Cup® Pack Holder

Funnel

K-Cup® Pack Assembly Housing

Drip Tray Overfill Indicator

Drip Tray Plate

Drip Tray

Cold Water Reservoir Lid

Cold Water Reservoir

BREW Button

LED Indicator

Power Button

Power Cord

Drip Tray Base

A

B

C

D

E

F

G

H

I

K

J

L

M

N

O

P

L

M

D

C

E

A

P

F

G

O

N

J

I

B

K

H

6 7

SECTION 2 Helpful Hints SECTION 3 Buttons & Indicators

Power Button (does not illuminate) 

Press to turn the brewer power on and off.

Add Water Indicator

Flashing Blue —Fill the Cold Water Reservoir

with cold water until it reaches just under the rim

of the desired level – 6, 8, or 10 oz. of the Water

Level Guide.

Handle Indicator  

Flashing Blue — The blue light flashes when the

minimum water amount of 6 oz. has been poured

into the Cold Water Reservoir. After adding your

desired amount of water (10 oz. maximum),

lower the Cold Water Reservoir Lid. The light will

continue to flash until you lift the Handle.

Brew Button  

Flashing Blue — Indicates you are ready to brew.

Press the BREW Button.

Flashing Red — Indicates water is heating

(approximately 2 minutes).

Solid Red — Indicates brewing and dispensing of

beverage has begun.

Your Next Brew

When the brewing process is complete, the Add Water

Indicator light will appear. At this point you can begin

making the next beverage, or you can power off.

Automatic Shut-Off

As a safety feature, your brewer will automatically

shut off at any stage when it is idle for longer than 90

seconds. Press the Power Button to restart. If it shut

off while the BREW Button was flashing blue, lift and

lower the Handle to reset.

Drip Tray Overfill Indicator

A red float will appear when the Drip Tray is almost

full. Carefully slide Drip Tray out and empty contents

into the sink.

1. Plug Power Cord into an Independent,

Grounded Outlet – If the electric circuit is

overloaded with other appliances, your brewer

may not function properly.

2. Initial Cleansing Brew – Before you make your

first beverage, perform an initial cleansing

brew without inserting a K-Cup® pack.

3. One Cup at a Time – Your new brewer makes

one fresh beverage at a time. You will need to

add fresh water each time you brew. Unlike

other Keurig® brewers, the K10 MINI Plus does

not store water in the reservoir.

4. The Right Water Makes a Difference – For the

best-tasting gourmet coffee, tea or hot cocoa,

Keurig recommends using bottled or filtered

water. We do not recommend using distilled or

reverse osmosis water. Note that water quality

can vary from place to place. If you notice an

undesirable taste in your beverage (such as

chlorine or other mineral substance), we

recommend trying bottled water or water from

a filtration system. For best results, carefully

follow manufacturer’s instructions when using

any water filtration system.

5. Customize Your Size, Flavor & Brew – With

over 200 K-Cup® pack varieties and multiple

fill levels, your brewer provides endless

customization options – so that you can create

the size, flavor and strength of each beverage

that is perfect for you. For a strong, intense

flavor, select an Extra Bold K-Cup® pack (with

up to 30% more ground coffee than regular

varieties) along with a brew size that’s right for

you. The less water you use, the more intense

the flavor in your cup. The more water you use,

the less intense the flavor in your cup.

Use the Water Level Guide located inside the Cold

Water Reservoir to customize your brew size.

6. Brewing Iced Beverages – Your iced tea and

iced coffee taste best when fresh-brewed hot

over ice. Try it by placing a tall cup filled with

ice on the Drip Tray, choose your favorite

K-Cup® pack and follow the brewing

instructions on page 8. Also, look for the

“Brew Over Ice” icon on K-Cup® packs specially

crafted to brew over ice! IMPORTANT: Do not

brew into a cup made of glass. Doing so may

cause the glass to crack or break.

7. Remove K-Cup® Pack After Use – Please see

page 8 for brewing instructions.

8. Brewing into a Tall Mug – To brew into a tall

mug, simply remove the Drip Tray Assembly

and place the tall mug on the Drip Tray Base.

Without the Drip Tray Assembly, however, you

do lose the benefit of the Drip Tray to contain

any excess water.

9. The Drip Tray – Any liquid overflow (from your

cup or from the Cold Water Reservoir) will be

caught in the Drip Tray. Be sure to empty the

Drip Tray when the red Drip Tray Overflow

Indicator pops up.

10. Automatic Shut-Off – As a safety feature, your

brewer will shut off automatically when it is

idle for longer than 90 seconds. Simply press

the Power Button to restart.

11 . Clean Your Brewer Regularly – To keep

your brewer looking and performing at its

best, be sure to clean the external and

internal components on a regular basis.

See page 12 for more information.

12. De-Scaling – Depending on the mineral

content of the water in your area, calcium

deposits or scale may build up in your brewer.

Scale is non-toxic, but left unattended, it can

hinder brewer performance. De-scaling your

brewer helps maintain the heating element

and other internal parts of the brewer that

come in contact with water. See page 14 for

more information.

13. Storing – When storing your brewer,

empty the Drip Tray. Follow the instructions

on page 14 for emptying the Internal Hot

Water Tank. Store your brewer upright in

a safe, dry, frost-free environment. See

page 15 for more information.

8 9

SECTION 4 Set-Up & Operation

CAUTION: Two sharp needles are used to puncture the

K-Cup® packs. One is above the K-Cup® Pack Holder and

the other is in the bottom of the K-Cup® Pack Holder. To

avoid risk of injury, do not put your fingers inside the

K-Cup® Pack Assembly Housing.

CAUTION: During the brewing process, the water

gets extremely hot. To avoid risk of injury, do not

lift the Handle or open the K-Cup® Pack Assembly

Housing until brewing is complete.

Plug the Power Cord into an

independent, grounded outlet.

Remove all tape and cardboard.

Perform an initial cleansing

brew before making your

first beverage. Follow these

instructions but do not insert

a K-Cup® pack.

Press the Power Button. The Add Water Indicator

will flash blue.

The Power Button does not illuminate.

Lift the Cold Water Reservoir Lid.

MAX

10 oz.

8 oz.

6 oz.

MIN

1 2

Pour water anywhere within the Cold Water

Reservoir until it reaches up to the rim of your

desired fill level on the Water Level Guide

(minimum of 6 oz.). Lower the lid.

For accurate measuring, do not fill if the

Handle is up.

Bottled or filtered water is recommended;

distilled or reverse osmosis water is not.

3 4

Initial Cleansing & First Brew

8

BREW

BREW

For accurate measuring, do not fill if the

Handle is up. In the down position it prevents

water from entering the lower heating

compartment.

1110

Lift the Handle. Water starts to drain

from the Cold Water Reservoir into

the brewer.

If you add more than 10 oz.,

excess water goes into the

Drip Tray.

Place mug on the Drip Tray.

If you want to use a taller mug,

you can slide the Drip Tray out,

but you will lose the benefit of

the tray to catch the excess

water.

56

SECTION 4 Set-Up & Operation (continued)

Insert the K-Cup® pack into the

K-Cup® Pack Holder.

Do not add a K-Cup® pack if

you are performing the initial

cleansing brew.

CAUTION: Do not lift the Handle

while brewing.

Wait until all water has drained

(5 seconds) into the brewer

before lowering the Handle

completely.

DO NOT remove foil lid or puncture K-Cup® pack.

Let water fully drain into brewer

before lowering the Handle.

7 8 10 119

The BREW Button will flash blue. Press the

BREW Button.

The BREW Button will flash red to

indicate that the water is heating. After

about 2 minutes, the BREW Button will

turn solid red when the beverage starts

to dispense.

Enjoy your beverage! Your brewer is ready to use

again or you can power it off.

! As a safety feature, brewer automatically

shuts off after 90 seconds.

If completing the initial cleansing brew,

discard hot water into the sink. Your brewer

is ready to use again.

Remove used K-Cup® pack after brewing.

CAUTION: K-Cup® pack will be hot.

2 Min

5 Sec

12 13

4. To replace the Funnel, just snap it back into the K-Cup®

Pack Holder (fig. 4).

5. To replace the K-Cup® Pack Holder Assembly, align the

K-Cup® Pack Holder with the opening using the two front

ribs as a guide and snap into place from the top (fig. 5).

Cleaning the K-Cup® Pack Holder Assembly

IMPORTANT: Make sure the brewer is unplugged before cleaning.

K-Cup® Pack Holder Assembly parts include:

• Funnel

• K-Cup® Pack Holder with Exit Needle

The K-Cup® Pack Holder Assembly parts can be placed on

the top shelf of the dishwasher. Use a low temperature cycle

when cleaning.

1. To remove the K-Cup® Pack

Holder Assembly from the brewer,

lift the Handle to open. Grasp the top

of the K-Cup® Pack Holder with one

hand. With the other hand, push up

on the bottom of the K-Cup® Pack

Holder Assembly until it releases (fig. 1).

2. Separate the Funnel from the K-Cup® Pack Holder by pulling it until it

snaps free (fig. 2).

3. Clean the Exit Needle on the bottom of the K-Cup® Pack Holder. Insert

a paper clip (fig. 3) or similar tool from below if needle becomes

clogged by coffee grinds.

Cleaning External Parts

IMPORTANT: Make sure the brewer is unplugged before cleaning.

Regular cleaning of the brewer’s external components is recommended.

• Brewer external housing

• Drip Tray

• Drip Tray Plate

BREWER

• Never immerse brewer in water or other liquids.

• Clean the external housing of the brewer and other external

components with a damp, non-abrasive, lint-free cloth.

DRIP TRAY AND DRIP TRAY PLATE

• When the red Drip Tray Overfill Indicator appears, the Drip Tray is

almost full. Carefully remove by sliding tray toward you. Empty

contents into the sink.

• Inspect the Drip Tray periodically and clean with a damp, non-abrasive,

lint-free cloth.

Do not put the Drip Tray or the Drip Tray Plate in the dishwasher.

fig. 3

SECTION 5 Cleaning & Maintenance

fig. 2

fig. 4

fig. 5

fig. 1

Avoid sharp needles in K-Cup®

Pack Assembly Housing. Do

not put your fingers inside the

K-Cup® Pack Assembly Housing.

1514

De-Scaling Your Brewer (continued)

FILL, CLEAN AND RINSE

Step 1: First Vinegar Rinse

• Fill the Cold Water Reservoir with 10 oz. of undiluted white vinegar.

• Place the ceramic mug on the Drip Tray.

• Lift the Handle, but do not add a K-Cup® pack.

• After 5 seconds, lower the Handle.

• Press the flashing blue BREW Button. It will flash red and then turn

solid red.

• Once the vinegar is dispensed, discard hot contents into sink.

Step 2: Second Vinegar Rinse

• Pour the remaining 10 oz. of vinegar into the Cold Water Reservoir.

• Place the ceramic mug on the Drip Tray.

• Lift the Handle, but do not add a K-Cup® pack.

• After 5 seconds, lower the Handle.

• Press the flashing blue BREW Button. It will then flash red.

• When it turns solid red, power off as it starts to dispense.

• Allow brewer to sit for 30 minutes.

• Power on the brewer, lift and lower the Handle, then press

BREW Button.

• Once the vinegar is dispensed, discard hot contents into sink.

Step 3: Fresh Water Rinse

• Fill the Cold Water Reservoir with 10 oz. of fresh water.

• Place the ceramic mug on the Drip Tray.

• Lift the Handle, but do not add a K-Cup® pack.

• Lower the Handle and continue the brewing process until the

hot water is dispensed into the mug. Discard hot contents into sink.

• Repeat this cleansing brew process three (3) more times to cleanse the

brewer plumbing and to remove any residual vinegar taste. The brewer

is now ready for normal use again.

Storage 

Empty the Internal Hot Water Tank and Cold Water Reservoir before storing.

See page 14. Store your brewer in a safe, frost-free environment in an

upright position.

Storing the brewer in cold temperatures may cause any residual

condensation to freeze inside the brewer and could cause damage.

Before using your brewer after storage, wipe the Cold Water Reservoir with a

damp, lint-free cloth and run three (3) cleaning brews (without K-Cup®

packs). See page 8 for initial cleansing brew process.

Let brewer rest at room temperature for at least 2 hours before

powering on.

Storing the Power Cord 

Behind the brewer is a convenient

compartment to hold the Power

Cord during transport or storage

(fig. 8).

Service

Beyond these recommended cleaning and maintenance procedures, this

brewer is not user serviceable. See page 18 for warranty guidelines. For

service, please refer to the Warranty section in this guide.

Cleaning the Cold Water Reservoir

It is normal over time for discoloration, spotting or staining to appear in

the Cold Water Reservoir. Results will vary depending on the mineral

content of the bottled or filtered water used but will not affect the

operation of the brewer. However, be sure to clean the Cold Water

Reservoir regularly to minimize build-up.

To access the Cold Water Reservoir, lift the lid. Remove the Water Level

Guide (fig. 6) and then clean inside the reservoir with a damp, lint-free cloth

as necessary (fig. 7).

Replace the Water Level Guide and lower the lid when finished.

The Water Level Guide is not dishwasher safe.

Emptying the Internal Hot Water Tank

Brewer must be powered off but plugged in.

• Lower the Cold Water Reservoir Lid.

• Place a mug on the Drip Tray.

• Press and hold down the BREW Button and continue to hold until all

the water is dispensed into the mug.

There will be a 3 to 5 second delay before water begins to dispense.

De-Scaling Your Brewer

Calcium deposits may build up in your brewer, depending on the mineral

content of your water. Scale is non-toxic but if left unattended, it can hinder

brewer performance. De-scaling your brewer helps to maintain the heating

element and other internal parts of the brewer.

The de-scaling process should be done every 3 to 6 months to ensure

optimal performance or when there are white deposits in the Cold Water

Reservoir. However, it is possible for calcium deposits to build up faster,

making it necessary to de-scale more often.

To begin, you will need the following:

• 20 oz. of undiluted white vinegar

• 12 oz. ceramic mug (do not use a paper cup)

• Access to a sink

fig. 6fig. 7

SECTION 5 Cleaning & Maintenance (continued)

fig. 8

16 17

• Brewer may be cold or frozen. Let brewer rest at room temperature for at least 2

hours before powering on.

• Make sure the brewer has power (see previous page).

• Allow enough time for water in the Cold Water Reservoir to drain completely into the brewer.

• The Exit Needle may be clogged (see page 12).

• Clean the K-Cup® Pack Assembly, if necessary (see page 12).

• De-scale the brewer (see page 14).

• If you have repeated the de-scale procedure two times and the brewer still does not

function properly, contact Customer Service.

• Under normal operation, the brewer will shut off when it is idle for longer than 90 seconds.

Just press the Power Button to restart.

• If the brewer shuts off in the middle of a brew (not from power outage), contact Customer Service.

• Remember that any liquid overflow (from your cup or the Cold Water Reservoir) will be

caught in the Drip Tray.

• When the Drip Tray is almost full, the red Drip Tray Overflow Indicator will appear. Carefully

remove the Drip Tray and empty its contents into the sink.

• This means that the Drip Tray is almost full. Carefully remove the Drip Tray and empty its

contents into the sink.

SITUATION SOLUTION

SECTION 6 Troubleshooting

Brewer does not have power

Brewer shuts off automatically

Brewer only brews a partial brew

Brewer will not brew when used for the first time

There is water in the Drip Tray

Red Indicator appears in Drip Tray

BREW Button flashes red too long

Add Water Indicator does not flash blue

Brewer will not brew

SITUATION SOLUTION

• Make sure the Power Button is pressed. The Add Water Indicator should flash blue

after pushing the Power Button. Note that the Power Button does not illuminate.

• During normal operation, the brewer will shut off when it is idle for longer than 90

seconds. Just press the Power Button to restart.

• Plug brewer into an independent outlet.

• Check to be sure that brewer is plugged in securely.

• Plug into a different outlet.

• Reset your home circuit breaker, if necessary.

• If the brewer still does not operate, contact Customer Service.

• Under normal operation, the BREW Button will flash red when the brewer is heating and

will turn solid red when brewing. If the BREW Button flashes red longer than 3 minutes,

contact Customer Service.

• If the Add Water Indicator does not flash blue, make sure the brewer has power (see above).

• Water may be in the Cold Water Reservoir and brewer. First, try raising the Handle to

drain all water from the Cold Water Reservoir into the brewer. If the light still does not flash,

power off and place a mug on the Drip Tray. Hold down the BREW Button and continue to

hold down until all the water is dispensed into the mug.

• If the brewer still does not operate, contact Customer Service.

• Make sure the brewer has power (see above).

• If using reverse osmosis or distilled water, the brewer may not operate correctly. See page 14 for

emptying the Internal Hot Water Tank and then use filtered or bottled water.

• Press the Power Button. If the Add Water Indicator flashes blue, add water and attempt

to brew. If the brewer loses power during the brew process, the brewer may need to be

re-set when power is restored. To re-set, simply lift and lower the Handle.

• Check that the minimum water level of 6 oz. has been poured into the Cold Water Reservoir.

Should other issues arise with your brewer, please call

Keurig Customer Service at 1.866.901.BREW (2739).

18 19

SECTION 7 Warranty

Limited One Year Warranty

Keurig, Incorporated warrants that your brewer will be free of defects in

materials or workmanship under normal home use for one year from the date

of purchase. It is recommended that you fill out and return the warranty card

enclosed with your brewer so that your purchase information will be stored

in our system. Keurig will, at its option, repair or replace a defective brewer

without charge upon its receipt of proof of the date of purchase. If a

replacement brewer is necessary to service this warranty, the replacement

brewer may be new or reconditioned. If a replacement brewer is sent, a new

limited one year warranty will be applied to the replacement brewer.

This warranty only applies to brewers operated in the United States and

Canada. This warranty gives you specific legal rights, and you may also have

other rights that vary from state to state and, in the case of Canada, from

province to province.

Only the use of Keurig Brewed® K-Cup® brand packs and accessories will

guarantee the proper functioning and lifetime of your Keurig® brewer.

Any damage to or malfunction of your brewer resulting from the use of non

Keurig Brewed® K-Cup® brand packs and accessories may not be covered

by this warranty or may result in a service fee if the damage or malfunction is

determined to be caused by such use.

What is not covered by the limited warranty?

THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL

DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER

INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH

OF THIS WARRANTY, EVEN IF FORESEEABLE. Some states or provinces

do not allow the exclusion or limitations of incidental or consequential

damages, so the above limitation or exclusion may not apply to you

depending on the state or province of purchase.

Nor does this warranty cover damages caused by non Keurig Brewed®

K-Cup® brand packs or accessories, services performed by anyone other

than Keurig or its authorized service providers, use of parts other than

genuine Keurig® parts, or external causes such as abuse, misuse,

inappropriate power supply or acts of God.

Other limitations

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER EXPRESS

WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION, KEURIG HEREBY

SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO

YOUR K10 MINI PLUS BREWER, INCLUDING ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Some

states or provinces do not allow disclaimers of such implied warranties or

limitations on how long an implied warranty lasts, so the above limitation

may not apply to you depending on the state or the province of purchase.

How do you obtain warranty service?

Keurig® brewers are high-quality appliances and, with proper care, are

intended to provide years of satisfying performance. However, should the

need arise for warranty servicing, simply call Keurig Customer Service at

our toll free phone number 1.866.901.BREW (2739). Please do not return your

brewer for servicing without first speaking to Keurig Customer Service to

obtain an Authorization to Return number (ATR). Keurig® brewers returned

without an ATR number will be returned to the sender without servicing.

Keurig, Incorporated

55 Walkers Brook Drive

Reading, MA 01867

1.866.901.BREW (2739)

Scan here for videos about caring for your brewer!

Scan this QR code with your smartphone for step-by-step videos on

cleaning, de-scaling and more. Or if you prefer, you can watch the videos

on your computer at bit.ly/NjTZ8W

Scan. Click. Call!

Learn more and reach us quickly without leaving home.

Have questions? We’re here to help!

Keurig is committed to your satisfaction. If you have questions, just give

us a call to have them answered quickly without leaving the comfort of

your home. 1.866.901.BREW (2739)

P/N 60-202467-000 Rev A

08/12

To learn more about Keurig, visit www.keurig.com or call 1.866.901.BREW (2739)

Keurig, Incorporated

55 Walkers Brook Drive

Reading, MA 01867

Keurig, Incorporated is a wholly-owned

subsidiary of Green Mountain Coffee Roasters, Inc.

For Household Use Only

Pat. www.GMCR.com/patents © 2012 Keurig, Incorporated

All rights reserved