Keyence 1395B Handheld Mobile Computer User Manual Users manual
Keyence Corporation Handheld Mobile Computer Users manual
Keyence >
Users manual
1E BT-W80GA/W85GA-IM
Handheld Mobile Computer
BT-W80GA/W85GA
Instruction Manual
Read this instruction manual before using the product in order to achieve maximum
performance. Keep this instruction manual in a safe place after reading it so that it can be
used at any time.
In this instruction manual, the BT-W80GA Series means the BT-W80GA and BT-W85GA.
Symbols
The following symbols alert you to important messages. Be sure to read these messages
carefully.
• IEEE802.11a/b/g/n: Wireless LAN standards established by 802 committee which has
designed standards of LAN technology in IEEE (Institute of Electrical and Electronics
Engineers).
• Bluetooth® wordmark and logo belong to Bluetooth SIG, Inc. and KEYENCE uses them
under license. Other trademarks or trade names belong to each owner.
•microSD
TM is a trademark of SD Card Association.
• Microsoft, Windows, Internet Explorer and Visual Studio are registered trademarks or trademarks
of Microsoft Corporation in the United States and other countries.
• The official name for Windows is "Windows® operating system".
• ARM Cortex is a trademark and registered trademark of ARM Limited in EU and other
countries.
• Other company names or product names described in this manual are registered
trademarks or trademarks of each company.
• It is prohibited to use or copy all or any part of this manual without prior approval.
• The information contained in this manual is subject to change without notice.
General cautions
This product employs a semiconductor laser for its light source.
* The laser classification for FDA(CDRH) is implemented based on IEC60825-1 in
accordance with the requirements of Laser Notice No.50.
Follow the instructions mentioned in this manual. Otherwise, injury to the human body
(eyes and skin) may result.
z
Locations of warning / explanation labels
Introduction
It indicates a hazardous situation which, if not avoided, will result in
death or serious injury.
It indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
It indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
It indicates a situation which, if not avoided, could result in product
damage as well as property damage.
It indicates cautions and limitations that must be followed during
operation.
It indicates additional information on proper operation.
It indicates tips for better understanding or useful information.
Safety Information for the BT-W80GA Series
• Do not use this product for the purpose of protecting a human body
or a part of human body.
• This product is not intended for use as an explosion-proof product.
Do not use this product in a hazardous location and/or potentially
explosive atmosphere.
• Suffocation may result from wrapping the lanyard around the neck. Be
careful to use BT-W80GA around a power-driven machine on work.
• Verify that this device is operating normally in terms of functionality
and performance before the start of work and when operating the
device.
• We recommend that you take substantial safety measures to avoid
any damage in the event that a problem occurs.
• If the equipment is used in a manner not specified by the
manufacturer, the protection provided by the equipment may be
impaired.
• Do not throw, drop or trample down the BT-W80GA Series and
accessories to strong physical shock.
• Keep BT-W80GA Series or accessories out of the reach of children.
Children may swallow batteries, batteries attachment covers and
straps around themselves.
• When the BT-W80GA Series is used in combination with other
instruments, functions and performance may be degraded, depending
on operating conditions and the surrounding environment.
• The LCD panel may generate microscopic spots (black/bright spot),
uneven brightness or crosstalk (phenomenon that non-existent lines
or patterns are displayed), depending on the conditions.
• If the same display remains on the screen for a long time, afterimage
may occur due to the characteristics of LCD.
DANGER
WARNING
CAUTION
NOTICE
Important
Point
Reference
DANGER
CAUTION
NOTICE
Safety Precautions on Laser Product
Item
BT-W80GA
BT-W85GA
Wavelength 655 nm 655 nm
Output 1.0 mW 390 ¦W
Laser Class
Class 2 laser product
(IEC60825-1,
FDA(CDRH) Part 1040.10*)
Class 1 laser product
(IEC60825-1,
FDA(CDRH) Part 1040.10*)
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation
exposure.
• Do not disassemble this product. Laser emission from this product
is not automatically stopped when it is disassembled.
Class 1 Laser Product
• Do not stare into the direct or specularly reflected beam.
Class 2 Laser Product
• Do not stare into the direct or specularly reflected beam.
• Do not direct the beam at other people or into areas where other
people unconnected with the laser work might be present.
• Be careful of the path of the laser beam. If there is a possibility that
the operator may be exposed to the specular or diffuse reflections,
block the beam by installing a protective enclosure.
• Install this product so that the path of the laser beam is not as the
same height as that of human eye.
Safety Precautions on LED Product
• Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation
exposure.
• Follow the instructions mentioned in this manual. Otherwise, injury
to the human body (eyes and skin) may result.
• Do not stare into the beam.
• Do not disassemble this product.
LED emission from this product is not automatically stopped when
it is disassembled.
• Do not view directly with optical instruments. Viewing the LED
output with certain optical instruments (for example, eye loupes,
magnifiers and microscopes) within a distance of 100 mm may
pose an eye hazard.
WARNING
CAUTION
BT-W80GA
Scanner
(Laser emission part)
BT-W85GA
Scanner
(Laser emission part)
96M13983
2
E BT-W80GA/W85GA-IM
FCC Regulations
• This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions; (1) This device may not cause harmful interface, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
• Application regulation
FCC Part 15 Subpart B ClassA
FCC Part 15 Subpart C
FCC Part 15 Subpart E
• The available scientific evidence does not show that any health problems are
associated with using low power wireless devices. There is no proof, however, that
these low power wireless devices are absolutely safe. Low power Wireless devices emit
low levels of radio frequency energy (RF) in the microwave range while being used.
Whereas high levels of RF can produce health effects (by heating tissue), exposure of
low-level RF that does not produce heating effects causes no known adverse health
effects. Many studies of low-level RF exposures have not found any biological effects.
Some studies have suggested that some biological effects might occur, but such
findings have not been confirmed by additional research. The BT-W80GA Series has
been tested and found to comply with FCC radiation exposure limits set forth for an
Controlled environment and meets the FCC radio frequency (RF) Exposure Guidelines.
• Compliance with FCC requirement 15.407(c)
Data transmission is always initiated by software, which is the passed down through the
MAC, through the digital and analog baseband, and finally to the RF chip. Several
special packets are initiated by the MAC. These are the only ways the digital baseband
portion will turn on the RF transmitter, which it then turns off at the end of the packet.
Therefore, the transmitter will be on only while one of the aforementioned packets is
being transmitted. In other words, this device automatically discontinue transmission in
case of either absence of information to transmit or operational failure.
• 5.15-5.35GHz band is restricted to indoor operations only.
• Frequency Tolerance: ±25ppm
IC Regulations
The BT-W80GA Series complies with the following regulations specified by the IC.
• Applicable regulation
ICES-003
RSS-247
• The available scientific evidence does not show that any health problems are
associated with using low power wireless devices. There is no proof, however, that
these low power wireless devices are absolutely safe. Low power Wireless devices emit
low levels of radio frequency energy (RF) in the microwave range while being used.
Whereas high levels of RF can produce health effects (by heating tissue), exposure of
low-level RF that does not produce heating effects causes no known adverse health
effects. Many studies of low-level RF exposures have not found any biological effects.
Some studies have suggested that some biological effects might occur, but such
findings have not been confirmed by additional research. The BT-W80GA Series has
been tested and found to comply with IC radiation exposure limits set forth for an
uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure
rules.
• 5150-5350 MHz band is restricted to indoor operation only.
High-power radars are allocated as primary users (i.e. priority users) of the bands
5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference
and/or damage to LE-LAN devices.
• Data transmission is always initiated by software, which is the passed down through the
MAC, through the digital and analog baseband, and finally to the RF chip. Several
special packets are initiated by the MAC. These are the only ways the digital baseband
portion will turn on the RF transmitter, which it then turns off at the end of the packet.
Therefore, the transmitter will be on only while one of the aforementioned packets is
being transmitted. In other words, this device automatically discontinue transmission in
case of either absence of information to transmit or operational failure.
• Les connaissances scientifiques dont nous disposons n’ont mis en évidence aucun
problème de santé associé à l’usage des appareils sans fil à faible puissance. Nous ne
sommes cependant pas en mesure de prouver que ces appareils sans fil à faible
puissance sont entièrement sans danger. Les appareils sans fil à faible puissance
émettent une énergie radioélectrique (RF) très faible dans le spectre des micro-ondes
lorsqu’ils sont utilisés. Alors qu’une dose élevée de RF peut avoir des effets sur la santé
(en chauffant les tissus), l’exposition à de faibles RF qui ne produisent pas de chaleur
n’a pas de mauvais effets connus sur la santé. De nombreuses études ont été menées
sur les expositions aux RF faibles et n’ont découvert aucun effet biologique. Certaines
études ont suggéré qu’il pouvait y avoir certains effets biologiques, mais ces résultats
n’ont pas été confirmés par des recherches supplémentaires. Le BT-W80GA série a été
testé et jugé conforme aux limites d’exposition aux rayonnements énoncées pour un
environnement non contrôlé et respecte les règles d’exposition aux fréquences
radioélectriques (RF) CNR-102 de l’IC.
• La bande 5150-5350 MHz est restreinte à une utilisation à l’intérieur seulement. Les
radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la
priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz, et ces radars pourraient
causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
• Conformité à la norme CNR-210 A9.4.4
La transmission des données est toujours initiée par le logiciel, puis les données sont
transmises par l'intermédiaire du MAC, par la bande de base numérique et analogique
et, enfin, à la puce RF. Plusieurs paquets spéciaux sont initiés par le MAC. Ce sont les
seuls moyens pour qu'une partie de la bande de base numérique active l'émetteur RF,
puis désactive celui-ci à la fin du paquet. En conséquence, l'émetteur reste uniquement
activé lors de la transmission d'un des paquets susmentionnés. En d'autres termes, ce
dispositif interrompt automatiquement toute transmission en cas d'absence
d'information à transmettre ou de défaillance.
UL certification
The BT-W80GA Series complies with the following UL/CSA standards and has obtaied
the UL/C-UL certifications.
• Applicable standards UL60950-1
• UL File No. E167973
• UL category NWGQ/NWGQ7
Mexico(Méjico)
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible
que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o
dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su
operación no deseada.
Precautions on Proper Use
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own
expense.
• FCC CAUTION
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
• This transmitter must not be co-located or operated in conjunction
with any other antenna or transmitter.
CAUTION
• This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired
operation of the device.
• Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes : (1) l'appareil ne doit
pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
CAUTION
CAUTION
3E BT-W80GA/W85GA-IM
Precautions on wireless LAN and Bluetooth
Handling of the BT-W80GA
Handling of packing
• Before attaching the rechargeable battery pack, make sure to check if the packing has
properly been set on the main unit side of the battery pack attachment cover.
• Do not use batteries other than BT-WB1GA.
• Make sure to charge BT-WB1GA when using for the first time.
• Before replacing the rechargeable battery pack, be sure to turn the power of the
BT-W80GA Series.
Attaching the rechargeable battery pack
1Slide the fixed lock lever in the arrow
direction (1) and remove the battery
attachment cover (2).
2Face the flat part of the new rechargeable
battery pack (BT-WB1GA) inward, and align the
contact polarity as shown in the illustration.
From the grip side (1), push in lightly with your
finger (2).
3Align the claw of the battery attachment
cover from the grip side and close (1). Slide
the lock lever in the arrow direction to fix (2).
• Remove the main battery of the BT-W80GA Series near locations
where using wireless devices is banned at medical institutions or
near electric devices for medical purposes. Carry and use the
product away from an implanted cardiac pacemaker.
• The BT-W80GA Series uses the radio wave of 5GHz band, and can
5.2GHz band (W52), 5.3GHz band (W53), 5.6GHz band (W56) and
5.8GHz band (W58). Using 5.2GHz band (W52) and 5.3GHz band
(W53) outdoors is prohibited by Radio Act.
• Retirez la batterie principale de la série BT-W80GA près des endroits
où l'aide d'appareils sans fil est interdite dans les établissements
médicaux ou à proximité d'appareils électriques à des fins
médicales. Transporter et à utiliser le produit en dehors d'un
stimulateur cardiaque implanté.
• Série BT-W80GA utilise l'onde radio de 5 GHz bande, et peut bande
de 5,2 GHz (W52), bande de 5.3GHz (W53), bande de 5.6GHz (W56) et
5,8 GHz bande (W58) utilisant la bande de 5,2 GHz (de W52) et de la
bande de 5.3GHz (W53) en plein air il est interdit par la loi Radio.
• Depending on the environment, communication may be impossible.
Check the communication availability before using.
• If this product is used near devices with the same frequency band,
such as a wireless LAN device, microwave oven, heating equipment
for industrial use, high-frequency equipment for medical use, etc.,
radio wave interference may occur and the communication speed
will become slow or communication may become impossible.
• If a wireless LAN and Bluetooth are used at the same time, radio
wave interference may occur and the communication speed will
become slow or communication may be interrupted. If there is
communication failure, stop using either the wireless LAN or
Bluetooth.
• Communication may be impossible at locations near metallic
objects, locations surrounded with metallic walls or where there is a
lot of metallic powder.
• Possible bluetooth communication distance is approx. 10 m of
vision, however, even within 10 m, communication may become
impossible depending on the environment. Check the
communication availability before using.
• Use within the temperature range described in “Specifications” (4
page). Do not leave the product inside a closed car or at a place
exposed to direct sunlight. Doing so may damage to the unit.
• Use within the humidity range described in “Specifications” (4
page). Do not use the product at locations where condensation
occurs due to the rapid temperature change. Doing so may damage
to the unit.
• This is a precision instrument. Dropping this product or subjecting
it to shock may cause damage. Be careful when carrying or using
this unit.
• Do not put the BT-W80GA Series at a location with high humidity or
a dusty area. Doing so may damage to the unit.
• Do not insert a sharp object such as a needle to the buzzer hole on
the back side of the BT-W80GA Series. The water-proof sheet may
be damaged.
WARNING
WARNING
Important
NOTICE
Precautions for proper use
• The BT-W80GA Series has an IP54 protection rating, however, if the
“Battery attachment cover” is not properly attached, the IP54 rating
cannot be guaranteed. When using in environments where water or
dust is present, check if these are properly attached.
• Dropping the BT-W80GA Series or subjecting to extreme shock may
lose water-proof feature. Handle with great care.
Attaching the rechargeable battery pack
Check that the lock lever is completely fixed.
If the lock lever is not completely fixed, the battery pack may come off.
When attaching or replacing the rechargeable battery pack, be careful
not to allow dust to enter inside. Contact failure may occur. This may
cause charging function to deteriorate and instantaneous
interruption.
NOTICE
(1)
(2)
(1)
(2)
(1)
(2)
Point
NOTICE
4
E BT-W80GA/W85GA-IM
Clean the following parts with air blow periodically.
If removing dirt is difficult, use a cotton swab to clean the contacts directly.
(Use absolute ethanol if dirt is stuck on them.)
Remove the battery attachment cover before cleaning the battery contact.
When opening the package, check the following items are all included.
If there is something missing, product failure or damage, contact your nearest KEYENCE
sales office.
BT-W80GA/W85GA
Cleaning
If dirt or dust is attached, contact failure may occur on the battery/
charging/communication contacts. This may cause charging function
to deteriorate and instantaneous interruption.
Make sure that waste textile is not attached to the battery/charging/
communication contacts when cleaning.
Checking the Package
BT-W80GA BT-W85GA
Scanner
(Laser emission part)
Charging/
communication contact
Battery contact
Scanner
(Laser emission part)
Charging/
communication contact
Battery contact
NOTICE
Main Unit…1
Battery Back
Cover...1
Instruction
Manual...1
Wrist strap...1 Stylus...1
Specifications
Item
Specifications
Model BT-W80GA BT-W85GA
Scanning Type Laser Type Camera Type
Control
part
CPU ARM Coretex®-A8 (800 MHz)
OS Microsoft® Windows® Embedded Compact 7
Main
memory
RAM 256 MB
ROM 512 MB Flash-ROM
Screen
Type 2.7 in transmissive TFT LCD (Vertically Aligned)
Resolution W 240 x H 320 (QVGA)
Color 65536 colors
Back Light Super luminosity white LED
Operation status LED tri-color LED
(red, green, blue, yellow, cyan, magenta, white)
Operation
part
Touch panel Analog resistance film (hardened glass)
Keyboard Number 27 keys
Backlight LED (orange)
Scanner
Reading
specification
Reading light
source
Visible light semiconductor
laser (655 nm)
Output 1.0 mW
Class 2 laser product
(IEC60825-1)"
Super luminosity red LED
Pointer light
source -
Visible light semiconductor
laser (655 nm)
Output 390 ¦W
Class 1 laser product
(IEC60825-1)
Scan count 100 scans/second -
Minimum
resolution 0.127 mm 2D code: 0.191 mm
Barcode: 0.127 mm
Reading
distance
62 to 542 mm
(narrow bar width 1.0 mm)
42 to 222 mm
(narrow bar width 0.25mm)
35 to 270 mm
(CODE39 narrow bar width
0.508 mm)
40 to 190 mm
(CODE39 narrow bar width
0.254 mm)
25 to 205 mm
(QR cell size 0.508 mm)
75 to 140 mm
(QR cell size 0.254 mm)
Reading width
(Field range) -81x 51 mm
(Reading distance 110 mm)
PCS
0.45 or more
(reflection rate of space part
70% or more)
-
Decoding capability
JAN/EAN/UPC
(add-on code compatible),
CODE128, GS1-128,
CODE39, NW-7, CODE93,
ITF, Industrial2of5,
COOP2of5, GS1-DataBar
JAN/EAN/UPC
(add-on code compatible)
CODE128, GS-128,
CODE39, NW-7, CODE93,
ITF COOP2of5,
Industrial2of5 QR code,
micro QR, DataMatrix
(ECC200),
PDF417, GS1-DataBar,
composite symbol
Wireless
communi-
cation
Wireless
LAN
Wireless
Radio IEEE802.11a/b/g/n
Radio
frequency
range
2.4 GHz (b/g/n: 1 - 11 ch)
5 GHz(a/n: W52,W53,W56,W58)
W52 can only be used indoors.
communication
distance
Indoors: 100 m of vision
Security
Security: WEP(64/128 bit)/
WPA/WPA2 WPA encryption: TKIP/AES
Authentication: WPA(2)-PSK /
TLS / PEAP /TTLS / LEAP / EAP-FAST
Bluetooth
Wireless
standard Bluetooth® V2.1 +EDR
Supported
profile
SPP, PAN(PANU), FTP(Client), HSP(AG),
HID(Host/Device)
Communica-
tion distance Approx. 10 m
Expansion
Slot
Supported media microSD/SDHC card
Capacity up to 32GB
Power
source
Main
battery
Type Rechargeable, removable Lithium ion battery pack
Capacity 2450 mAh
Continuous
usage time Approx. 23 hours*1,3
Charging time Approx. 4.5 hours (at room temperature)
Backup
battery
Clock Built-in lithium secondary battery (approx. 1 month)*2,3
RAM data Electric double layer capacitor (approx. 4 minutes)*2,3
Others
Buzzer Musical tones: 16 tones Volume: 3 levels
Vibration function Enable (Pattern is not variable)
Clock accuracy ± 80 seconds per month (at room temperature)
5E BT-W80GA/W85GA-IM
*1 This indicates the case when barcodes are read once per 20 seconds and round trip
wireless communication is made at room temperature with the operation status LED,
vibration function OFF, the buzzer ON (low volume), the backlight ON (brightness 1) and
the charging mode2.
*2 This indicates the case when the main battery is not attached or the battery level is low,
and operations are performed at room temperature.
*3 This is a typical value at room temperature, but not a guaranteed value.
*4 Replace the main battery at a temperature of -5 °C or higher.
The product may not start in low-temperature environments.
BT-W80GA
BT-W85GA
Environ-
ment resis-
tance
Enclosure sealing IP64 (IEC60529)
Drop resistance Multiple drops to concrete:
3.0 m*3
Multiple drops to concrete:
2.5 m*3
Operation temperature -5 to +50 °C (No freezing)*4
Operation humidity 20 to 85%RH (No condensation)
Storage temperature -20 to +60 °C (No freezing)
Storage humidity 20 to 85%RH (No condensation)
Dimensions () shows grip parts. 173 x 61.6 x 37.7 (30.3) mm 173 x 61.6 x 40.4 (30.3) mm
Weight with battery pack 223 g 227 g
Accessory Battery Back Cover, Wrist strap, Stylus pen
Item
Specifications
Outline dimensional drawing
63
61.6
47.8
173
37.7
30.3 unit (mm)
63
61.6
47.8
173
40
30.3 unit (mm)
-20
6
E BT-W80GA/W85GA-IM
Copyright (c) 2016 KEYENCE CORPORATION. All rights reserved.
13983E 1076-1 96M13983 Printed in Japan
(1) KEYENCE warrants the Products to be free of defects in materials and workmanship
for a period of one (1) year from the date of shipment. If any models or samples
were shown to Buyer, such models or samples were used merely to illustrate the
general type and quality of the Products and not to represent that the Products
would necessarily conform to said models or samples. Any Products found to be
defective must be shipped to KEYENCE with all shipping costs paid by Buyer or
offered to KEYENCE for inspection and examination. Upon examination by
KEYENCE, KEYENCE, at its sole option, will refund the purchase price of, or repair
or replace at no charge any Products found to be defective. This warranty does not
apply to any defects resulting from any action of Buyer, including but not limited to
improper installation, improper interfacing, improper repair, unauthorized
modification, misapplication and mishandling, such as exposure to excessive
current, heat, coldness, moisture, vibration or outdoors air. Components which wear
are not warranted.
(2) KEYENCE is pleased to offer suggestions on the use of its various Products. They
are only suggestions, and it is Buyer's responsibility to ascertain the fitness of the
Products for Buyer’s intended use. KEYENCE will not be responsible for any
damages that may result from the use of the Products.
(3) The Products and any samples ("Products/Samples") supplied to Buyer are not to
be used internally in humans, for human transportation, as safety devices or fail-safe
systems, unless their written specifications state otherwise. Should any Products/
Samples be used in such a manner or misused in any way, KEYENCE assumes no
responsibility, and additionally Buyer will indemnify KEYENCE and hold KEYENCE
harmless from any liability or damage whatsoever arising out of any misuse of the
Products/Samples.
(4) OTHER THAN AS STATED HEREIN, THE PRODUCTS/SAMPLES ARE
PROVIDED WITH NO OTHER WARRANTIES WHATSOEVER. ALL EXPRESS,
IMPLIED, AND STATUTORY WARRANTIES, INCLUDING, WITHOUT
LIMITATION, THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF PROPRIETARY
RIGHTS, ARE EXPRESSLY DISCLAIMED.
IN NO EVENT SHALL KEYENCE AND ITS AFFILIATED ENTITIES BE LIABLE
TO ANY PERSON OR ENTITY FOR ANY DIRECT, INDIRECT, INCIDENTAL,
PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES (INCLUDING, WITHOUT
LIMITATION, ANY DAMAGES RESULTING FROM LOSS OF USE, BUSINESS
INTERRUPTION, LOSS OF INFORMATION, LOSS OR INACCURACY OF DATA,
LOSS OF PROFITS, LOSS OF SAVINGS, THE COST OF PROCUREMENT OF
SUBSTITUTED GOODS, SERVICES OR TECHNOLOGIES, OR FOR ANY
MATTER ARISING OUT OF OR IN CONNECTION WITH THE USE OR INABILITY
TO USE THE PRODUCTS, EVEN IF KEYENCE OR ONE OF ITS AFFILIATED
ENTITIES WAS ADVISED OF A POSSIBLE THIRD PARTY’S CLAIM FOR
DAMAGES OR ANY OTHER CLAIM AGAINST BUYER. In some jurisdictions,
some of the foregoing warranty disclaimers or damage limitations may not apply.
BUYER'S TRANSFER OBLIGATIONS:
If the Products/Samples purchased by Buyer are to be resold or delivered to a third
party, Buyer must provide such third party with a copy of this document, all
specifications, manuals, catalogs, leaflets and written information provided to Buyer
pertaining to the Products/Samples.
E 1101-3
WARRANTIES AND DISCLAIMERS