Keys Fitness Health Trainer 700 Users Manual HT700 11 5 01
700 to the manual e81da581-f091-4761-b04e-cad787524d5c
2015-02-02
: Keys-Fitness Keys-Fitness-Health-Trainer-700-Users-Manual-435043 keys-fitness-health-trainer-700-users-manual-435043 keys-fitness pdf
Open the PDF directly: View PDF 
.
Page Count: 19
| Download | |
| Open PDF In Browser | View PDF |
HEALTH TRAINER 700 TREADMILL OWNER’S MANUAL KEYS Fitness Products, LP P.O. Box 551239 Dallas, Texas 75239 Table of Contents Information Page # Table of Contents 2 Specification Sheet 3 Important Safety Information 4 Before You Start 5 Warm Up Exercises 6 Assembly, Moving Instructions 7 Power Requirements 8 Console Functions and Descriptions 9 Program and Operating Instructions 10 &11 Program Descriptions and Profiles 12 Belt Adjustments and Tension 13 Maintenance Instructions 14 Change to MPH or KM 15 Troubleshooting Guide 16 Parts and Diagrams 17 Parts List 18 Warranty Registration (Mail In Form) 19 Page 2 Specification Sheet ♦ HT700 Horsepower (Continuous) 1.75hp ♦ Display Type 4 Window LCD ♦ Electronics Push button ♦ Pre-Set Programs 3 ♦ Custom Programs 6 ♦ Speed/Incline Toggles Switches Yes ♦ Power Incline 0-12% ♦ Roller Diameter 2.5” ♦ Cushioned Deck Yes ♦ Speed Range 0-10mph ♦ Belt Size 20 x 56” ♦ Side Hand Rails Yes ♦ Foot Print 32 x 71” ♦ Foot Print Folded 32 x 26” ♦ Warranty Motor 10 Years ♦ Warranty Parts 2 Years ♦ Warranty Labor 1 Year ♦ Warranty Frame Lifetime PAGE 3 Important Safety Information 1) WARNING! Before using this treadmill or starting any exercise program, consult your physician. This is especially important for persons over the age of 35 and/or persons with pre-existing health problems. The manufacturer or distributor assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 2) WARNING! To reduce the risk of electrical shock, burns, fire, or other possible injuries to the user, it is important to review this manual and the following precautions before operation. SAFETY PRECAUTIONS AND TIPS ♦ It is the owner’s responsibility to ensure that all users of this treadmill have read the Owner’s Manual and are familiar with warnings and safety precautions. ♦ This treadmill has a user maximum capacity of 275 pounds. ♦ The treadmill should only be used on a level surface and is intended for indoor use only. The treadmill should not be placed in a garage, patio, or near water and should never be used while you are wet. KEYS recommends a treadmill mat be placed under the treadmill to protect floor or carpet and for easier cleaning. ♦ Follow safety information in regards to plugging in your treadmill. Keep the power cord away from the incline wheels and do not run the power cord underneath your treadmill. Do not operate the treadmill with a damaged or frayed power cord. ♦ Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use the treadmill with bare feet, sandals, socks or stockings. ♦ Always straddle the belt and allow it to start moving before stepping onto the belt. ♦ Hold on to handrails when adjusting speed, incline, or other controls. ♦ Always examine your treadmill before using to ensure all parts are in working order. ♦ Allow the belt to fully stop before dismounting. ♦ Pets should never be allowed near or on the treadmill. ♦ Do not leave children unsupervised near or on the treadmill. ♦ Never operate the treadmill where oxygen is being administered, or where aerosol products are being used. ♦ Never insert any object or body parts into any opening. ♦ For safety and to prevent damage to your treadmill, no more than one person should use the treadmill at a time. ♦ Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by an authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow these instructions will void the treadmill warranty. ♦ Never leave the treadmill unattended while it is running. PAGE 4 Before You Start Thank you for purchasing a KEYS treadmill! The HEALTH TRAINER 700 treadmill was designed to meet your needs for cardiovascular exercise. Before you start, please read the Owner’s Manual and become familiar with the operation of your new treadmill. ♦Remember to take the time to perform the stretching exercises provided on Page 6 to avoid injury. ♦Do not stand on the walking belt while pressing the Power button or Start/Stop button. ♦Always adjust the speed of the treadmill in small increments as this treadmill is capable of high speeds. ♦If you are taking medication, consult your physician to see if the medication will affect your exercise heart rate. ♦If you have heart problems, you are not active, and/or are over the age of 35 years, do not use the pre-set treadmill programs or start an exercise program without first contacting and receiving approval from your physician. ♦To avoid the risk of electrical shock, always keep the console dry. Do not spill liquids on the console. KEYS recommends a sealed water bottle for beverages consumed while using the treadmill. ♦ Please review the following picture below to familiarize yourself with the listed parts. This manual covers several treadmills, so the one pictured below may not be identical to your particular model. READING RACK CONSOLE ELECTRONIC DISPLAY WATER BOTTLE HOLDER (WATER BOTTLE NOT INCLUDED) SIDE HAND RAILS SAFETY LATCH UPRIGHTS WALKING BELT MOTOR COVER REAR ROLLER ADJUSTMENT BOLTS WHEEL FOOT RAILS PAGE 5 Warm Up Exercises EXERCISE GUIDELINES WARNING! Before beginning this or any exercise program, you should consult your physician. This is es- pecially important for individuals over the age of 35 or individuals with pre-existing health problems. Warming up prepares the body for the exercise by increasing circulation, supplying more oxygen to the muscles and raising body temperature. Begin each workout with 5 to 10 minutes of stretching and light exercise to warm up. The photos on this page show several forms of basic stretching you may perform before your workouts. In order to achieve an adequate warm-up, perform each stretch three times. TOE TOUCH STRETCH Stand bending your knees slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible. Hold for 15 counts, then relax. This will stretch your hamstrings, back of knees , and back. HAMSTRING STRETCH Sit with one leg extended. Bring the sole of the opposite foot toward you and rest it against the inner thigh of your extended leg. Reach toward your toes as far as possible. Hold for 15 counts, then relax. This will stretch your hamstrings, lower back, and groin. CALF/ACHILLES STRETCH With one leg in front of the other, reach forward and place your hands against a wall. Keep your back leg straight and your back foot flat on the floor. Bend your front leg, lean forward and move your hips toward the wall. Hold for 15 counts, then relax. To cause further stretching of the Achilles tendons, bend your back leg as well. This will stretch your calves, Achilles tendons, and ankles. QUADRICEPS STRETCH With one hand against a wall for balance, reach back and grasp one foot with your other hand. Bring your heel as close to your buttocks as possible. Hold for 15 counts, then relax. This will stretch your quadriceps and hip muscles. PAGE 6 Assembly, Moving Instructions The HT700 is shipped in two pieces, please see assembly instructions below. After opening the box, remove any packing materials from the treadmill. Do not throw away any packing materials until the unit is working properly. Place the base on a clean, level surface. Make sure the electrical cord will easily reach an electrical outlet. Assembly See Figure 1 To attach End cap: 1. Place plastic end cap over exposed rear roller area. 2. Align holes in plastic end cap with pre-drilled holes in frame. 3. Loosely tighten each screw until all four screws are lined up. 4. Tighten all four screws snugly. Moving See Figure 2 CAUTION! TO AVOID THE RISK OF INJURY, NEVER ATTEMPT TO MOVE THE TREADMILL WHILE IT IS IN THE UNFOLDED OPERATING POSITON. TO REDUCE THE POSSIBILITY OF INJURY WHILE LIFTING, BEND YOUR LEGS AND KEEP YOUR BACK STRAIGHT. AS YOU RAISE THE TREADMILL, LIFT USING YOUR LEGS, NOT YOUR BACK. IN ORDER TO RAISE OR LOWER THE TREADMILL SAFELY, YOU MUST BE ABLE TO LIFT 45 POUNDS (20KG). IT IS SUGGESTED YOU ALWAYS USE THE AID OF A SECOND PERSON WHEN MOVING THE TREADMILL. With the treadmill in the folded locked position (safety latch is engaged), grasp the handrails and place one foot on the base as shown in the photo below. Next, with a firm grasp on handrails, place one foot on the center of the base crossbar and carefully tilt the treadmill back until it rolls freely on the wheels. Using extreme caution, move the treadmill to the desired location. To set the treadmill down, place one foot on the center of the base crossbar and carefully lower treadmill onto base in resting position. Do not attempt to move the treadmill over an uneven or rough surface. Figure 2 Figure 1 PAGE 7 Power Requirements ARNG! IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN A RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT THE OUTLET, HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN. This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges, and noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of treadmill damage, always use a surge protector (not included) with your treadmill. Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with a UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less and an electrical rating of 120VAC, 15 amps. This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for electric current, should the treadmill malfunction. This treadmill comes with an electrical cord having an equipment-grounding conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. This product is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug illustrated in the drawing below. PAGE 8 Console Functions and Descriptions There are four display windows on the control panel to provide feedback information. TIME WINDOW ♦ ♦ TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59 seconds) INTERVAL TIME: Indicates countdown in seconds to the next interval starting at 5 seconds and counting to 0 seconds SPEED WINDOW ♦ SPEED: Indicates MPH (miles per hour) or KMH (kilometer per hour) in .1 increments DISTANCE / CALORIES WINDOW ♦ ♦ DISTANCE: Indicates Miles or Kilometers traveled in .01 increments up to 9.99 and .1 increments starting at 10.0 CALORIES: Indicates estimated calories used based on 150 lb. person at the indicated speed, incline, and time INCLINE WINDOW ♦ INCLINE: Indicates incline in percent of grade 0-12% in .5 increments INCLINE WINDOW TIME WINDOW DISTANCE/CALORIE WINDOW PAGE 9 SPEED WINDOW Program and Operating Instructions ♦ QUICK START / MANUAL MODE ♦ Plug into a surge protector outlet. Attach RED Safety Key to treadmill console. ♦ Stand on the treadmill and straddle belt. Attach safety key clip to your clothes. ♦ Press POWER button.There will be an eight (8) second delay after pressing the POWER button before data can be entered. The TIME window will flash. ♦ Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt starts moving. Speed or incline may be adjusted by using the appropriate + (increase) or – (decrease) buttons, or toggle switches on side hand rails. ♦ To end your workout, press START/STOP button. Belt will gradually slow to zero. ♦ To pause your workout, press PAUSE. ♦ To re-start after pausing: Press the PAUSE button. WARNING: THE TREADMILL BELT WILL RESUME AT THE SPEED THE TREADMILL WAS MOVING BEFORE PAUSING. ♦ Countdown Time, Preset Speed and/or Incline: Time, Speed, and Incline may be preset prior to getting started. After pressing the POWER button, the time window will blink. Use the SPEED + or – arrows to select your workout time, then press the ENTER PROGRAM button. The SPEED window will now be flashing. Using the same + or – arrows, select the speed for your workout, then press ENTER PROGRAM. Now the INCLINE window will be flashing. Use the INCLINE + or – arrows to set your workout incline, then press ENTER PROGRAM. To start, press the START/STOP button. SPEED/TIME INCLINE ENTER START/STOP RED SAFTEY KEY HOLDER PAGE 10 PAUSE POWER Program and Operating Instructions PROGRAM MODE-FOR THE HT700 ♦ Plug treadmill into a surge protector outlet . Attach RED Safety Key to treadmill console. ♦ Stand on the treadmill and straddle belt. Attach safety key clip to your clothes. ♦ Press POWER button. There will be an eight (8) second delay before data can be entered. The TIME window will flash. ♦ There are three (3) pre-set and six (6) custom pre-set programs on the DCV100. The treadmill includes FAT BURN, CARDIO, and WARM-UP programs. To select the program press the MODE button until desired program is illuminated on console display. ♦ Each of the pre-set programs can also be customized for your particular workout. ♦ CUSTOMIZING PROGRAMS in P1 and P2 Mode: Each pre-set program(Fat Burn, Cardio, Warmup) can be customized in the P1 or P2 mode. After making the program selection, the CAL/DIST window will read “OP.” The ”OP” refers to “original program” and is preset. The program you select will illuminate on console display. Press the MODE button once more and the CAL/DIST window will read P1. The “P1” mode is now accessed. You can now program the Time, Speed, and Incline in P1 mode, which will be saved for future workouts. 1) The TIME window will blink. Use the SPEED/TIME + or – arrows to select your workout time. Press ENTER PROGRAM. 2) The SPEED window will then blink. Use the same + or – arrows to select the speed for your workout. Press ENTER PROGRAM. 3) The INCLINE window will then blink. Use the INCLINE + or – arrows to set your workout incline. Press ENTER PROGRAM. To start, press the START/STOP button. To access P2 mode, press the MODE button for desired program, then press the MODE button again (once for OP, twice for P1, three times for P2). Follow the above steps 1-3 to customize P2 settings. ♦ TO CHANGE A PREVIOUSLY PROGRAMMED P1 or P2: Once you have programmed the P1 or P2 modes, you will need to use the PAUSE button to change the program you previously entered. For instance to change to a new setting in P1-FAT BURN, press the MODE button to reach the FAT BURN program, then once to access P1. Then press the PAUSE button to get the TIME window to flash. Follow the directions above to continue to change the program. FAT BURN CARDIO WARM UP ENTER MODE START/STOP PAUSE PAGE 11 POWER Program Profiles SPEED 1 2 1 1 1 0 9 8 7 6 5 4 INCLINE 12 11 10 9 8 7 6 5 4 3 2 1 12 11 10 9 8 7 6 5 4 3 2 1 INCLINE 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 10 The Fat Burn Program is designed to vary the treadmill elevation, while maintaining a constant walking belt speed. SPEED The Cardio Program is designed to vary the treadmill Speed, while maintaining a constant Elevation. SPEED INCLINE 1 2 3 4 5 6 7 8 9 10 The Warm Up Program is designed to gradually increase the treadmill Speed and Elevation in the first segment (warm up) and gradually decrease the treadmill Speed and Elevation in the last segment (cool down). This is also known as a Plateau program. PAGE 12 Belt Adjustment and Tension WARNING! Do not overtighten rollers! This will cause premature roller bearing failure! Belt adjustment and tension performs two functions: adjustment for tension and centering. Your new treadmill comes pre-adjusted from the factory for tension and centering. Please follow the procedures below if the belt shifts to the left or right or while walking: WALKING BELT IS SHIFTING TO THE LEFT (Diagram 1) First, turn treadmill on to run at 1 mph. Using the hex key provided, turn the left rear roller adjustment bolt ¼ turn in the clockwise direction. Next, run the treadmill at 2.5 mph. You should see the belt start to correct itself, moving back towards the center. Repeat the above procedure until the walking belt is centered. It may be necessary to set walking belt tension once you have completed this procedure if the belt feels like it is slipping while walking. Refer below to the “Walking Belt Slipping” instructions. WALKING BELT IS SHIFTING TO THE RIGHT (Diagram 2) First, turn the treadmill on to run at 1 mph. Using the hex key provided, turn the right rear roller adjustment bolt ¼ turn in the clockwise direction. Next, run the treadmill at 2.5 mph. You should see the belt start to correct itself, moving back towards the center. Repeat the above procedure until the walking belt is centered. It may be necessary to set walking belt tension once you have completed this procedure if the belt feels like it is slipping while walking. Refer below to the “Walking Belt Slipping” instructions. WALKING BELT IS SLIPPING DURING USE (Diagram 3) First, unplug the power cord from the surge protector. Using the hex key provided, turn both left and right rear roller adjustment bolts the same distance, usually a ¼ turn in the clockwise direction. Plug the power cord back into the surge protector and run the treadmill at 2.5 mph. You should now walk on the belt to determine if the belt is still slipping. Repeat the above procedure until the walking belt is not slipping. The tension should be just tight enough not to slip. ♦ Turning the hex key counter clockwise brings the rear rollers and belt towards you. Turning the hex key clockwise pushes the rear roller and belt away form you. PAGE 13 Maintenance Instructions WARNING! Before performing any maintenance to your treadmill, always unplug the power cord from the surge protector. CLEANING Routine cleaning of your Keys Fitness treadmill will extend the life of your treadmill. WARNING! To prevent electrical shock, be sure the power to the treadmill is OFF and the unit unplugged from the wall electrical outlet before attempting any cleaning or maintenance. AFTER EACH WORKOUT: Wipe off the console and other treadmill surfaces with a clean, water dampened soft cloth to remove excess perspiration. USE NO CHEMICALS. WEEKLY: Use of a treadmill mat is recommended for ease of cleaning. Dirt from your shoes contacts the belt and eventually makes it to underneath the treadmill. Vacuum underneath treadmill once a week. DECK LUBRICATION The walking belt has been pre-lubricated at the factory. However, it is recommended that the walking board be checked periodically for lubrication to ensure optimal treadmill performance. Every 30 days or 30 hours of operation, lift the sides of the walking belt and feel the top surface of the walking board as far under as you can reach. If you feel signs of silicone, no further lubrication is required. If it feels dry to the touch, follow the instructions below. KEYS recommends “Lube N Walk” for cleaning and lubricating the treadmill belt and deck. Ask your retailer or call KEYS at 800-340-0482. You may also use silicone such as “Napa 8300” (available at most stores). TO APPLY LUBRICANT TO THE WALKING BOARD 1) Position the walking belt so that the seam is located on top and in the center of the center of the walking board. 2) Insert the spray nozzle into the spray head of the lubricant can. 3) While lifting the side of the walking belt, position the spray nozzle between the walking belt and the board approximately 6” from the front of the treadmill. Apply the silicone spray to the walking board, moving from the front of the treadmill to the rear. Repeat this on the other side of the belt. Spray approximately 4 seconds on each side. 4) Allow the silicone to ‘set’ for one minute before using the treadmill. WARNING: Do not overlubricate the walking board. Excess lubricant should be wiped off with a clean towel. Page 14 Change Miles per hour to Kilometers per hour Your treadmill will operate in British Units (miles per hour) or International Units (kilometers per hour). All treadmills are calibrated at the factory for British Units (miles per hour). To change the display to read in kilometers, follow the steps described here: 1) Turn power OFF on the console. (Do not unplug treadmill) Attach the magnet safety key to the console. 2) Activate the calibration mode switch by inserting the eraser end of a pencil into the opening in the backside of the console (see diagram below). 3) Depressing the calibration mode switch ONCE; CL11 should appear in the TIME window. 4) Pressing the SPEED +/- button will activate your choice. 5) To accept the setting, press the POWER button. Page 15 Troubleshooting Guide Treadmill will not start. 1) Is the RED Safety Key Attached to the Console? 2) Make sure the power cord is plugged into a surge protector, the surge protector is plugged into a properly grounded outlet, and the surge protector is turned on. (Refer to “Power Requirements” on page 8) 3) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped. Wait five minutes and then press the switch back in. 4) Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in. If it has tripped, reset or have an electrician replace the breaker in home. 5) Have an electrician check for inadequate voltage at the outlet. Treadmill losses power during use. 1) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped. Wait five minutes and then press the switch back in. 2) Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in. If it has tripped, reset or have an electrician replace the breaker in home. 3) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482. Treadmill walking belt slows during use. 1) Check to make sure the treadmill is securely plugged into an UL-listed surge protector, rated at 15 amps, with a 14-gauge cord of five feet or less and the surge protector is securely plugged into the outlet. 2) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482. Treadmill walking belt slips or is not centered on rear roller. 1) Refer to “Belt Adjustment and Tension” section on page 13. 2) Need help? Call Keys Technical Service at (888) 340-0482. Treadmill Error Messages. Your treadmill is equipped with a software package that enables error messages to be displayed when there is a problem. To avoid possible damage to the treadmill and the possibility of injury, do not operate the treadmill until the problem is corrected. Call Keys Technical Service at (888) 340-0482. Page 16 Parts & Diagrams 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. & 16. 17. 05-0041-Extrusion side board deluxe/left 05-0041-Extrusion side board deluxe/right 04-0019-Belt walk spliced 19.5 x 113.75WW 24-0176-Front roller assembly 09-0020-Rear roller assembly 03-0014-Walking board 06-0159-End cap 12-0022-Actuator 400lb Maytech 06-0156-Motor base pan 06-0080-Small motor fan 12-0023-Motor MCM 1.5HP 04-0004-Poly V belt 190J8 06-0157-Motor cover w/wings 10-0020-Hand grips 07-0027 & 24-0185 Console assembly 08-0122-Motor controller Page 17 HT700 PARTS LIST PART # 02-0002A DESCRIPTION QTY PART # DESCRIPTION SPRINT-DECK LIFT 4 06-0166 EXT BOOT LT BLACK 02-0004 SCREW-8x5/8 PHIL PH AB BLACK 35 07-0027 ELECTRONIC-LCD 4 WIN-HORZ REV 02-0005 SCREW-8x5/8 PPH HILO BLACK TPB 6 08-0004 BREAKER-CIRCUIT-15AMP 02-0007 NUT 5/16-18 NYLOCKZP 10 08-0027 SWITCH-REMOTE-W/HARNESS 02-0009 BOLT-HEX 5-16-18x3/4"GRADE 2-ZP 7 08-0047 ENCODER-OPTICAL-OJ-3705 ALEPH 02-0011 WASHER-FLAT 5/16 16GA 7PUSS 9 08-0077 CORE-FERRITE 02-0013 WASHER LOCK 1/4" 8 08-0065 MEBRANE-LCD 4WIN PH2 02-0015 WASHER-SPRING 2 08-0099 SPEED BULLET 02-0018 NUT-PUSH 3/8 HAT BLACK 375012 4 08-0121 MAGNET & HOUSING 02-0019 BOLT-CARRIAGE 10-24x1 1/2 4 08-0122 CONTROLLER 08-0051 N MERCRY 02-0020 SCREW-SHCS 14-20x2 1/2" 2 09-0020 ROLLER REAR 2.5"x24.5" CONV&FOLD 02-0021 WASHER 9/32 5/8 1/8THICK ZP 2 09-0021 ROLLER FRONT 2.5x22.93" FOLD 02-0022 NUT-NYLOCK HEX 10-24 4 10-0004 RUBBER FOOT 02-0024 CARRIAGE BOLT 5/16x1 GRADE 5 ZP 4 10-0017 TAPE-FOAM-1"X75ft 02-0027 NUT-T HF 14209H-DB 16 10-0018 GROMMET-SPEED BULLET 02-0028 SWITCH-MAGNETIC KILL-YIHAN 1 10-0020 GRIP MOLDED ROUND 02-0036 SCREW-PPH 8x5/8 GREEN HEAD 2 10-0023 BOARD ISOLATORS 17/32" SHORT 02-0038 WRENCH ALLEN 3/16 SHAFT ARM 1 10-0024 TAPE-ADHESIVE 1'C108FT ST567 02-0042 SCREW#8x5/8' SD BLACK 1 11-0013 AXLE WHEEL 2 3/8" 02-0050 NUT-NYLOCK HEX 1/4-20 2 11-0020 PIVOT PIN FOLD 3/8" & CHAMFER 02-0058 WASHER FLAT NYLON 3/8 2 11-0022 BUSHING KEYED 02-0119 SCREW-HEX HD 1/4-20x3 1/4" 8 11-0023 FYWHEEL 1.125 10MPH FOR 2.5ROLLERS 02-0137 PLUG PUSH IN 2 12-0022 ACTUATOR 400 LB-MAYTECH 02-0141 PUSH NUT BLACK .112 SHAFT 5 12-0023 MOTOR-MCM#2917-1.5HP-10MPH-8MM 02-0143 BOLT HEX 1/4-20x1" 8 13-0011 CORD-POWER-90" 02-0145 COTTER PIN 1" 2 13-0014 WIRE-JUMPER 12"-220V-KEYS SERIES 02-0146 BOLT SHCS FULL TRO 1/4-20x1 3/4 2 13-0018 SWITCH REEDSD1951 TERMINATED PS500 02-0147 BOLT CRG FULL BODY 5/16-18x1" 9 13-0020 HARNESS ENCODER KEYS SERIES 02-0149 BOLT CRG 5/16-18x1 3/4" GRADE 5 2 13-0045 JUMPER WIRE OR PEED BULLET 02-0151 BOLT SHOULDER SHSB 3/8x3/8" 5/16-18 1 13-0046 HARNESS CONTROLLER 80" 03-0014 WALKBOAD KORETRON 56" FOLD 1 14-0026 DECAL-WARNING CONSOLE-ALL GRAY 04-0004 BELT-POLY V 190J8 1 14-0027 DECAL-EMERGENCY STOP-RED 04-0019 WALKBELT 1 PLY 19.51x113.75 FOLD 1 14-0028 DECAL-CIRCUIT BREAKE-ALL 05-0041 EXTRUSION-SD BRD-LT&RT 56"FOLD 2 14-0053 DECALINCLINE EMOTE 06-0004 PLUG-BASE 1.5x3"-16GA 4 14-0054 DECAL-SPEED REMOTE 06-0012 WHEEL 3" 2 14-0178 STICKER-MOTOR HP 1.5 06-0014 BUSHING-STRAIN RELIEF #1237 1 14-0204 DECAL-CAUTION OPER INST 06-0016 TIES-WIRE 12 14-0205 DECAL-DISCONNECT-MOTOR COVER 06-0021 CLAMP WIRE 3367 7/16 2 14-0321 DECAL 10YR MOTOR WARRANTY 06-0022 GUIDE-RESET TUBE 1 14-0343 OVERLAY CONSOLE HT700 06-0024 CLIP-ALLEN WRENCH 1 14-0339 DECAL MOTOR COVER HT SERIES 06-0029 SPACER-WHEEL 3/16 4 18-0005 ROD-AXLE3/8x2"-ETF 06-0080 FAN 5"X8mm BORE-SCREW ON 1 19-0015 BRKT-MOTOR COVER 06-0084 BAG-PLASTIC 12x12 3MIL-INST PACKET 1 19-0019 GUIDE-BELT GALVANIZED 06-0090 WHEEL-2 3/8 (SNAP ON) 4 19-0107 SLUG-EMERGENCY STOP 06-0117 SWITCH HOUSING ROUND GRAY 2 19-0173 BRKT LINKAGE 06-0153 CONSLE WEEBOK 4WIN HORZ-REV 1 19-0177 BRKT CHANNEL SUPPORTS 06-0144 PULLE DRIVE 2.5" 8 GROOVE 1 19-0188 BRKT SPEED BULLET 06-0149 SHEET BOTTOM FOR FOLD BLACK 1 19-0189 BRKT MAGNET 06-0151 PLUG RECT 1x3x16GA 2 23-0111 UPRIGHT ASSEMBLY NEW FOLD-WEEBOK 06-0156 BOTTOM PAN FOR FOLD BLACK 1 24-0176 FRONT ROLLER ASSEMBLY 06-0157 COVER FOR MOTOR NEW FOLD BLACK 1 24-0180 CONSOLE ASSEMBLY DCV300 06-0159 ENDCAP DUAL BLACK 1 26-0089 INST PACKET BLACK FOLD 06-0165 EXT BOOT RT BLACK 1 PAGE 18 Keys HEALTH TRAINER HT700 Treadmill KEYS FITNESS PRODUCTS, LP – LIMITED WARRANTY PLEASE CONSULT YOUR PHYSICIAN BEFORE USING THIS PRODUCT. This Limited Warranty applies in the United States and Canada to products manufactured or distributed by Keys Fitness Products, LP (“Keys”) under the KEYS brand name. The warranty period on the HT700 to the original purchaser is (lifetime) on the frame, (10) years on the motor, (2) years parts, and (1) year labor. Keys warrants that the Product you have purchased for non-commercial, personal, family, or household use from Keys or from an authorized Keys reseller is free from defects in materials or workmanship under normal use during the warranty period. Your sales receipt, showing the date of purchase of the Product, is your proof of the date of purchase. This warranty only extends to you, the original purchaser. It is not transferable to anyone who subsequently purchases the Product from you. It excludes expendable parts. This Limited Warranty becomes VALID ONLY if the treadmill is assembled/installed by a Keys Fitness authorized dealer/technician unless otherwise authorized by Keys Fitness in writing (if anyone other than a Keys Fitness authorized dealer/technician assembles a Keys Fitness treadmill the warranty will be void unless accompanied by written authorization by Keys Fitness). During the warranty period Keys will at no additional charge, repair or replace (at Keys’ option) the product if it becomes defective, malfunctions, or otherwise fails to conform with this Limited Warranty under normal non-commercial, personal, family or household use. In repairing the Product, Keys may replace defective parts, or at the option of Keys, serviceable used parts that are equivalent to new parts in performance. All exchanged parts and Products replaced under this warranty will become the property of Keys. Keys reserves the right to change manufacturers of any part to cover any existing warranty. To obtain warranty service, you must contact a Keys authorized service technician or Keys Fitness at our phone numbers located in this manual. Any parts determined to be defective must be returned to Keys to obtain warranty service. You must prepay any shipping charges, export taxes, custom duties and taxes, or any other charges associated with transportation of the parts or Product. In addition, you are responsible for insuring any parts or Product shipped or returned. You assume the risk of loss during shipment. You must present Keys with proof-of-purchase documents (including the date of purchase). Any evidence of alteration, erasing or forgery of proof-of-purchase documents will be cause to void this Limited Warranty. This warranty does not extend to any product not purchased from Keys or from an authorized Keys reseller. This Limited Warranty does not extend to any Product that has been damaged or rendered defective; (a) as a result of accident, misuse, or abuse; (b) by the use of parts not manufactured or sold by Keys; (c) by modification of the Product or normal wear and tear; (d) operation on incorrect power supplies; or (e) as a result of service by anyone other than Keys, or an authorized Keys warranty service provider. Product on which the serial number has been defaced or removed is not eligible for warranty service. Should any Product be submitted for warranty service be found ineligible therefore, an estimate of repair cost will furnished and the repair will be made if requested by you upon Keys’ receipt of payment or acceptable arrangements for payment. EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, KEYS MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. KEYS EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. NEITHER KEYS NOR ANY OF ITS AFFILIATES SHALL BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. This Limited Warranty gives you specific legal rights and you may also have other rights that may vary from state to state. This is the only express warranty applicable to Keys-branded products. Keys neither assumes nor authorizes anyone to assume for it any other express warranty. PLEASE SEND IN THE ATTACHED WARRANTY CARD WITHIN TEN (10) DAYS OF PURCHASE TO REGISTER YOUR TREADMILL WITH KEYS FITNESS PRODUCTS, LP. MADE IN THE USA. Thank you for your business! PLEASE MAIL WARRANTY CARD TO: KEYS FITNESS PRODUCTS, PO BOX 551239, DALLAS, TX 75355. KEYS FITNESS TREADMILL WARRANTY REGISTRATION LAST M.I. FIRST TELEPHONE ADDRESS APT. NO. CITY STATE DATE OF PURCHASE Name of store or company where purchased: How do you plan to use the treadmill? Walk____ Run_____ Both_____ Who will use the treadmill? Male____ Female_____ Both_____ How many family members? _____ AGE: 15-24____ 25-34____ 35-44____ 45-54____ 55-64____ 65 +_____ ZIP SERIAL NO. MODEL NO. Where did you learn about treadmills? TV____ Radio____ Friend____ In Store Display____ Salesperson___ Print ad/flyer____ Internet______ Why did you purchase a treadmill? Dr.’s Orders____ Loose Weight____ In-home convenience____ Improve Cardiovascular Fitness___ Safety from outdoors____ Other __________________________ How important are each feature: Least Unique Features Horsepower Warranty Price Look/Design Folding Feature Most Other Comments: _______________ _______________ _______________ _______________ KEYS FITNESS respects the rights of your privacy. Our company will not sell or distribute to others the information above. This information is used to track our product quality and to contact you in the event of a product safety concern. It may be used to offer you future Keys products only through the mail. Please check here if wish not to receive any additional information on Keys products.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 2002:09:18 13:44:59-05:00 Modify Date : 2002:09:18 13:44:59-05:00 Page Count : 19 Creation Date : 2002:09:18 18:44:59Z Mod Date : 2002:09:18 18:44:59Z Producer : Acrobat Distiller 5.0 (Windows) Author : tammy Metadata Date : 2002:09:18 18:44:59Z Creator : tammy Title : HT700 MANUAL 11-5-01EXIF Metadata provided by EXIF.tools