KeyScan KSMART3 K-SMART3 Contactless Smartcard/BLE Reader User Manual Manual

Keyscan Inc. K-SMART3 Contactless Smartcard/BLE Reader Manual

Manual

8 Keyscan Inc. A Member of the Kaba Group 901 Burns St. E., Whitby, Ontario, Canada L1N 0E6 1.888.539.7226 (toll free Canada/USA) 905.430.7226 (elsewhere) www.keyscan.ca Technical Support Hours — 9:00 AM to 6:30 PM Eastern Time K-SMART3 Installation Guide (Document # KD10085-1017) FCC Compliance Statement: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer-ence, and (2) this device must accept any interference received, including interference that may cause undesired operation. Product can be used without license conditions or restrictions in all European Union coun-tries, including Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxem-bourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Spain, Sweden, United Kingdom, as well as other non-EU countries, including Iceland, Norway, and Switzerland. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause unde-sired operation of the device. Cet appareil est conforme à Industrie Canada exempts de licence standard RSS (s) . Le fonctionnement est soumis aux deux conditions suivantes : (1) ce dispositif ne peut pas provoquer d’interférences et (2) ce dispositif doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequen-cy energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be re-quired to correct the interference at his own expense. Changes or modifications not expressly approved by Keyscan could void the user’s au-thority to operate the equipment. K-SMART3 Bluetooth Proximity Reader Installation Guide This guide outlines how to install the K-SMART3 Bluetooth proximity reader. This reader has dedicated function LEDs and enhanced security features designed for Keyscan access control systems with compatible firmware. Enhanced security and LED features may not function with non-Keyscan control boards. See K-SMART3-ACU Compatibility on page 3. Keyscan Inc. A Member of the Kaba Group 901 Burns Street East, Whitby, Ontario, Canada L1N 0E6 K-SMART3 Features • Uses proven digital radio frequency identification technology • Has dedicated access and power LEDs • Designed for indoor or outdoor use • Suitable for mullion or single-gang mounting • Electronics sealed in tamper-resistant epoxy potting • Bluetooth functionality Table of Contents Features 1 LEDs & Security Features 2-3 Bluetooth Functionality 3 Dimensions & Templates 4-5 Wiring Connections 6 Optional Programming Card 7 Specifications 7 Parts List K-SMART3 Reader 1 Wall Switch Plate 1 Mullion Mount Box 1 6-32 x 1/4” Phillips Screw 1 6-32 x 1/4” Security Screw 1 6-32 x 1” Screws 2 #6 x 1” Screws 2 Enhanced Features • Has dedicated Present3 and Global Lockdown LEDs • Offers physical and cable anti-tamper capability for enhanced security (tamper switch not included) • Has innovative heartbeat to detect wiring faults and/or reader damage
2 K-SMART3 Overview LEDs and Security Features The K-SMART3 has 4 distinct LEDs to report the state of a system-specific function. In addition, the K-SMART3 has an anti-tamper capability and a heartbeat for en-hanced reader security. The following sub-headings re-view the K-SMART3’s LED, anti-tamper and heartbeat functions. Control boards require System PROM ver-sion 9.39 or higher when connected to a K-SMART3 reader for full functionality; for example, using LED 3 for Present3 or LED 4 for Global Lockdown. KEYSCANKI-00556E-06 -16Secure reader to plate with enclosed security screw*.1 234* Both Phillips & #10 PIN Torx screws provided. Torx driver not included.LED 1—Door Lock State • Red—indicates the door is locked / remains red on an Access Denied • Green—indicates the door is unlocked / green during Relay Unlock Time On and Access Granted The control board must be configured for Reader LED (Red/Green Enabled) mode. LED 2—Power The backlit Keyscan logo indicates reader power: • Not illuminated—indicates the reader does not have power • Illuminated blue—indicates the reader has power LED 3—Present3 The Present3 mode can trigger a door lock and change time zone schedules. When con-figured for operation at the reader, LED 3 functions as follows: • Not illuminated—Present3 is off/Door Toggle - locked/Schedule - time zone is on • Illuminated amber—Present3 is on/Door Toggle - unlocked/Schedule - time zone is off LED 4—Global Lockdown LED 4 indicates when a Global Lockdown is in effect as follows: • Not illuminated—a Global Lockdown is not in effect • Illuminated red—a Global Lockdown is in effect The reader must be connected to a control board that has Global Lockdown configured. Note: LED 3—Present3 and LED 4—Global Lockdown are unique features for Keyscan control boards and require System PROM firmware version 9.39 or higher. 7 K-SMART3 Enhanced Features K-SMART3 enhanced features, which include Heartbeat and Tamper, are turned on by default. With the purchase of the K-PC2 programming card, K-SMART3 enhanced features can be toggled on and off. This will enable backwards compatibility with previous versions of Keyscan ACUs, even if they do not have the required firmware 9.39 or higher to work with other manufacturer’s access control systems. If the K-SMART3 enhanced features are used on an un-supported access control board, the reader will produce a Card Not in ACU alarm approximately every 60 seconds. This will not affect the reader’s ability to read cards. Keep this programming card close at hand for future use with any K-SMART3 reader to toggle the enhanced features on or off. K-PC2 programming cards are available in pack-ages of 5 individual cards. Specifications Dimensions: Mullion: 11.5 cm x 4.49 cm x 1.7 cm (4 7/16” x 1 11/16” x 11/16”) Wall Plate: 12 cm x 7.6 cm x 1.6 cm (4 3/4” x 3” x 5/8”) Power Requirements 12 VDC, 125mA Read Range (with typical clamshell card) Off Metal: up to 3 cm On Metal: up to 3 cm Cable 18” wire pigtail standard Wiegand interface—22 AWG 6 conductor shielded cable, 152 metres/500 ft. maximum Environmental Operating Temperature: -40 to 66 °C (-40 to 150.8 °F), 93% RH Installation Installation and wiring of systems must be in accordance with the National Electrical Code, ANSI/NFPA 70. Connections Connections must be in accordance with NFPA 70. Reader and/or control unit power sources must not be connected to a receptacle controlled by a switch. Certifications UL-294 - Fifth Edition, CAN/ULC-S319-5 - First Edition, FCC ID: WFW-KSMART3 & IC: 5241A-KSMART3, ETSI EN 301 489-1 V2.1.1 (2017-02), ETSI EN 301 489-3 V2.1.1 (2017-03), ETSI EN 301 489-17 V3.1.1 (2017-02), EN 55032: 2012/AC:2013, ETSI EN 300 330 V2.1.1 (2017-02), ETSI EN 300 328 V2.1.1 (2016-11), Canadian Industrial De-sign Certificate of Registration: 169,198 and 169,199.
6 K-SMART3 Connections with a PC109x Control Board K-SMART3 shown with ABS wall switch plate.KI-00600E-0517LED (Brown)D1 (White)D0 (Green)PWR (Red)GND (Black)Shield not connected.Isolate with electrical tape.ShieldACU Ground LugD1 (White)D0 (Green)PWR (Red)GND (Black)LED (Brown)Yellow not used. Isolate with electrical tape.PurplePre-alert (Blue)OrangeShield not connected.Isolate with electrical tape.Pre-alert (Blue)6 conductors – shielded 22 AWG Maximum 500 ft (152.4 m)Blue used for pre-alert otherwise isolate with electrical tapeYellowReader terminal on control boardLED D1WHTD0GRNPWRREDGNDBLKC1(BEEP)KEYSCANShieldPurple (Read Mode)For Secure Sector Read only—Isolate and tape back Purple wire at reader. This is the recommended read mode which offers higher security. For Secure Sector and/or CSN Read—Connect Purple wire to GND Black wire at reader.Orange (Tamper)- when using an optional Tamper Switch (Normally Closed) locally at reader, connect to GND Black wire.- when not using Tamper Switch, connect to GND black wire at reader.3 Anti-Tamper Capability When connected to an anti-tamper switch (not supplied), the K-SMART3 offers an en-hanced level of security. Connect the K-SMART3’s orange conductor as follows: • With tamper switch—connect the orange wire to the optional tamper switch (normally closed) locally at the reader and connect to GND black wire at the reader • Without tamper switch—connect the orange wire to GND black wire at the reader In the event of tampering, the Client software reports a reader tamper alarm. Refer to the wiring diagram on page 6. Heartbeat The K-SMART3 has an innovative heartbeat that detects wiring faults and/or reader dam-age. The heartbeat is sent by the reader to the ACU every 45 seconds. In the event that 3 consecutive heartbeats are not received by the ACU (approx. 180 seconds), the Client software reports a reader communication failure alarm. K-SMART3—ACU Compatibility The K-SMART3’s enhanced features—Present3 LED, lockdown LED, heartbeat and orange tamper conductor—require PC1097 control boards with firmware version 9.39 or higher. The K-SMART3 is backwards compatible with PC1094, PC1095 and previous green ACU/ECU control boards. The K-SMART3 can be used with other access control systems, but the enhanced features will not be available. To configure the K-SMART3 for backwards compatibility with the listed control boards or other manufacturer’s control boards, an optional programming card (not supplied) Part # K-PC2 is required. See details on page 7. K-SMART Credential Compatibility The K-SMART reader keypad is compatible with the following credential formats: K-SECURE 1k & 4k cards, K-SF-1K key fobs, K-TX2-1K — Four Button RF Transmitter, 14443A Credentials (CSN only). Bluetooth Functionality The K-SMART3 is a Bluetooth-enabled reader and is capable of working with Keyscan mobile credentials. The default read state out of the box is Polling Mode — Short Range. K-BLE Mobile Credential This reader uses K-BLE mobile credentials loaded on any supported mobile device (contact Keyscan for ordering information). This mobile credential can be used in con-junction with physical credentials used with proximity readers. Download the “Keyscan Mobile” App from either the App Store on IOS-based devices or Google Play on Android-based devices. K-BLE mobile credentials are not sold through distribution. Only available for purchase directly from Keyscan. Reader Modes & Reader Ranges The K-SMART3 has two reader modes: Watch Mode and Polling Mode. Watch Mode has only short range BLE and standard range for physical credentials. Polling Mode can have different ranges: short, medium, long and standard range (for physical credentials). The default reader mode out of the box is Polling Mode (short range). To change reader modes or polling ranges, the purchase of an optional BLE1 Programming Card pack is required. Note: Read ranges are omnidirectional. Actual BLE mobile read ranges will differ based upon the mobile device manufacturer and model number type; these aspects cannot be specified.
4 Dimensions—Mounting Template Wall Plate 3/4"(1.9 cm)KI-00580E-06-164 3/4"(12 cm)3"(7.6 cm)TOP5 Dimensions—Mounting Template Mullion 1 11/16"(4.49 cm)TOP3/4"(1.91 cm)4 7/16"(11.5 cm)KI-00581E-06-16

Navigation menu