Keystone Heddolf P219311 FIX CODE TRANSMITTER User Manual P219 2KB 311 201610

Download:
Mirror Download [FCC.gov]
Document ID	3268178
Application ID	lCIQ4zfW/gf9wEuDAg4Ntw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	15.11kB (188864 bits)
Date Submitted	2017-01-23 00:00:00
Date Available	2017-01-23 00:00:00
Creation Date	2016-11-17 11:34:14
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2017-01-23 19:13:54
Document Title	Microsoft Word - P219-2KB-311-201610
Document Creator	PScript5.dll Version 5.2.2
Document Author:	dorisgao

INSTRUCTIONS FOR Radio Control Operator
Dual entry transmitter P219-2KB
Read the following instructions thoroughly before using the remote.
This transmitter must be adjusted so that the coding switches match the coding
on your present operating transmitters or receiver.
FCC Regulations: This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept an interference
received, including interference that may cause undesired operation.
Remove the Transmitter
Cover
for battery replacement
and set the Coding
Switches
Transmitter distance may vary due to circumstance beyond our control.
Programming Remote Controller to the Opener
1. Remove the Transmitter Cover
Remove the screw from the back of the transmitter with a small Phillips
screwdriver. Lay the transmitter circuit board with the button facing up.
Unsnap the top of transmitter to access the coding switches.
2. Setting the codes
You may set your transmitter to any code you desire, but be sure the code you
set matches both your transmitter and receiver.
Figure A
3. Replace Battery
If the red light on transmitter is dim when the transmitter button is pushed, the transmitter battery may be
weak. Remove the screw from the back of the transmitter with a small Phillips screwdriver. Replace battery
with a 23A 12 volt battery.
Transmitter Switches
Receiver Switches
In the transmitter, there are eight (8) dip switches,
each of which can be placed in three different
positions (+, 0, -). DO NOT set all switches in the
same position, such as all +, all -, or all zero (Figure
A). WARNING: No other adjustments should be
made inside the transmitter.
Figure B
In the receiver, there are nine (9) dip switches. Set
Figure C
the first eight switches in the receiver so that they
match exactly as the eight switch settings on the transmitter (Figure B). You will set the ninth dip switch to
correspond with transmitter button that you wish to use to open garage door. On this Dual Transmitter, the
left button has a (+) setting, and the Right button has a setting of (0). Set the ninth switch in the receiver to
the same setting (＋,0) as the button you wish to use. For example, if you wish to use the Right button on the
Dual Transmitter to open your garage, you should set the ninth dip switch on the receiver to (0).
Be sure not to use the same transmitter button that you selected to activate the gate opener. For example, on
a Dual Transmitter, if you set the Left button to open your gate, you would use the Right button to open your
garage door.
Warning
To avoid possible serious injury or death from a garage door or moving gate:
-Keep all remote controls out of children’s reach at all times. Never allow children near batteries!
-Only activate door or gate when it is in clear view and is in proper working condition.
-Always completely monitor garage door and gate opener until completely opened or closed.
-Never allow anyone to cross area of opening and closing of moving garage door or gate.
-Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
Copyright@ Keystone/Heddolf Remotes 2016

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : dorisgao
Create Date                     : 2016:11:17 11:34:14+08:00
Modify Date                     : 2017:01:23 19:13:54+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2017:01:23 19:13:54+08:00
Producer                        : Acrobat Distiller 11.0 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - P219-2KB-311-201610
Creator                         : dorisgao
Document ID                     : uuid:eaaa9032-8c8a-4b80-86a1-28f30a1fcc6f
Instance ID                     : uuid:036face3-374e-4626-87ce-fa4ebaf1a65b
Page Count                      : 2

EXIF Metadata provided by EXIF.tools