Kicker Zx Series Zx700 5 Users Manual TEMP 2006 ZX550 3 700 4in1 A01.qxp
ZX700.5 to the manual 066e7a5c-7e45-4310-8395-bdfb9b1e7b57
2015-02-05
: Kicker Kicker-Zx-Series-Zx700-5-Users-Manual-400639 kicker-zx-series-zx700-5-users-manual-400639 kicker pdf
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
ZX
MULTI-CHANNELAMPLIFIER
with a CLASS-DSUBWOOFERCHANNEL
ZX550.3, ZX700.5
©2006 Stillwater Designs
Figure 2
ZX.3/ZX.5SeriesAmplifier
Owner’sManual
Use only one type of signal input to the
amplifier, either RCA Cable or Speaker Wire
Speaker Wire
(High-Level
Output)
SOURCE
UNIT Top”
killers
trk7“on
Multi-ChannelModels:
Congratulations on your
KICKER purchase
Please record your purchase
information and keep your sales
receipt for validation of warranty.
ZX550.3 / ZX700.5
RCA Cable
(Low-Level)
Optional RCA
Subwoofer Cable
Speaker Wire
(High-Level Input)
Authorized Kicker Dealer: __________________________
Purchase Date:
__________________________
Left
Left
Right
Right
+
+
SUB INPUT
SUB
Amplifier Model Number: __________________________
ZX550.3
Amplifier Serial Number:
__________________________
CONFIGURATION
Installation . . . as easy as 1, 2, 3
Figure 3
1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The controls on the
top of the amplifier need to be accessible for adjustment. Make sure there are no items behind the area
where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for
the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four
holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier.
Minimum impedance of 2 ohms in the Subwoofer Channel
and 2 ohms per channel in stereo operation of the AMPs
Mono Speaker
Subwoofer Channel
(60cm)
-
24"
Or Less
+
Signal In AMP 2
2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then connect the ground wire
to the amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and
Figure 1
corrosion-free solid-metal area of the vehicle's
Use only one type of signal input to the
Optional RCA
amplifier, either RCA Cable or Speaker Wire
Speaker Wire
chassis. Adding an additional ground wire between
Subwoofer Cable Output
(High-Level
Output)
the battery's negative post and the vehicle chassis
killers trk7“on Top”
of this same gauge (or larger) is recommended.
Left
+
Use a twisted pair(s) of RCA (low-level)
RCA Cable
Left
(Low-Level)
Right interconnect cable to feed the audio signal to the
Right +
Speaker Wire
(High-Level
Input)
amplifier. If you are using only one pair of RCA
Left
+
Left
inputs, connect the RCA cable to the AMP 1
Right Right +
inputs. All three (or five ZX700.5) channels will
work with a single pair of RCA input cable; the
fader will not operate. Keep the RCA cable away
ZX700.5
When using both sets of high-level
from factory wiring harnesses and other power
(speaker wire) inputs the supplied RCA
Optional RCA
dummy plugs must be inserted into the
wiring. If you need to cross this wiring, cross it at a Subwoofer Cable Input
RCA AMP 2 inputs in order for
the fader to work properly.
90 degree angle.
Only use speaker wire (high-level) inputs if your source unit does not have RCA type outputs. When
using both sets of high-level inputs for the ZX700.5, the supplied RCA dummy plugs must be inserted
into the RCA AMP 2 inputs in order for the fader to work properly. In any other configuration do not use
the RCA dummy plugs. Never use shorting plugs in any configuration. See Figure 1.
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your
amplifier. If you ever need to remove the amplifier from the vehicle after it has been installed, the ground
wire should be the last wire disconnected from the amplifier--just the opposite as when you installed it.
See the chart below for power and
ground wire size, and fusing
ModelZX550.3
Fuse60A
PowerGroundWire 4GA
recommendations.
ModelZX700.5
Fuse90A
PowerGroundWire 4GA
Signal In Subwoofer
(Optional)
Ground
Signal In AMP 1
Remote
Turn-On
(45cm)
SOURCE UNIT
+12V
-
+
18"
Or Less
-
+
Fuse
Battery
ZX700.5
Left Speaker AMP 1
Right Speaker AMP 1
-
+
+
-
SUB INPUT
INSTALLATION
SUB
Right Speaker AMP 2
Left Speaker AMP 2
Figure 4
Minimum impedance of 2 ohms in the Subwoofer Channel
and 4 ohms per AMP in bridged operation
Mono Speaker
Subwoofer Channel
(60cm)
-
24"
Or Less
+
Signal In AMP 2 (Left)
Signal In Subwoofer
(Optional)
Ground
3. Configuration The following diagrams show the most common configurations for your Kicker ZX
series amplifier.
Signal In AMP 1 (Right)
Remote
Turn-On
(45cm)
Four (ZX700.5) / Two Channel (ZX550.3) Operation with Subwoofer These ZX amplifiers are
capable of operating into a minimum impedance of 2 ohms per channel in stereo operation and
2 ohms mono in the subwoofer channel. See Figure 3.
Bridged (Mono) Operation (ZX700.5) The ZX700.5 series amplifier is capable of operating into a
minimum impedance of 4 ohms when in bridged operation. This allows you to bridge AMP 1 to run the
“right” side and AMP 2 to run the “left” side. You will need two RCA Y-Adapters for this configuration.
Each AMP is stable down to 4 ohms in this configuration. See Figure 4.
2
ZX.3/ZX.5AMPLIFIER
+
18"
Or Less
+12V
Battery
-
+
-
Fuse
ZX700.5
Right Speaker AMP 1
Left Speaker AMP 2
Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.
Note: All specifications and performance figures are subject to change. Please visit the www.kicker.com for the most current information.
3
volume levels. Short circuit protection is engaged. Check for speaker wires shorted to each other or to the vehicle
chassis. Check for damaged speakers, or speaker(s) operating below the minimum recommended impedance.
Operation
Your Kicker ZX series amplifier has five (or seven ZX700.5) rotary controls on top and one
(or two ZX700.5) switch(es) on the end-panel. Before turning on the system for the first time, turn the
rotary controls on the top of the amplifier to the full counter-clockwise position.
OPERATION
1. CrossoverSwitch The crossover switch(es) on the end-panel is
(are) for setting the internal crossover(s) for the “full-range” audio
channels (12dB slope per octave). In the OFF position the amplifier
passes a full-range signal to the speakers. The HI position should be
selected when connected to speakers, which you do not want to
receive any sub-bass information. Never change the crossover
"OFF/HI" switch setting with the audio system on!
2. InputGainControl The input gain control is not a volume control.
It matches the output of the source unit to the input level of the
amplifier. Turn the source unit up to about 3/4 volume (if the source
unit goes to 30, turn it to 25). Next, slowly turn (clockwise) the gain
on the amplifier up until you can hear audible distortion, then turn it
down a little. Set AMP 1 first, then AMP 2 (ZX700.5 only) and finally
the Subwoofer Channel input gain control.
Figure 5
Subwoofer Channel
Input Gain Control
Crossover Control
Subwoofer Channel
Bass Boost Control
Subwoofer Channel
Alternator noise-whining sound with engine’s RPM? 1) Check for damaged RCA (or speaker input) cable
2) Check the routing of RCA (or speaker input) cable 3) Check the source unit for proper grounding 4) Check the
gain settings and turn them down if they are set too high
Poor stereo image or reduced bass response? Check system phasing by turning the balance control from left
to right. If there is more bass output when turned to either side, then check your speaker wiring, passive crossover
networks and speaker terminals for proper positive and negative connections. Reverse a speaker connection from
positive to negative on the stereo/subwoofer channel(s); if the bass improves, the speaker was out of phase.
Ground-Loop Noise? If you are using only one pair of RCA inputs, connect the RCA cable to the AMP 1 inputs.
AMP 1 Input
Gain Control
AMP 2 Input
Gain Control
ZX700.5
3. BassBoostControl The bass boost control is designed to give
you increased output 0 - 18dB at 40Hz for the subwoofer channel.
The setting for this control is subjective. If you turn it up, you must go
back and adjust the input gain control to avoid clipping the amplifier.
No output from one channel? 1) Check the balance control on source unit 2) Check the RCA (or speaker input)
and speaker output connections for the channel 3) Swap the RCA (or speaker input) cable from left to right. If the
problem changes sides then you have a bad RCA (or speaker input) cable or source unit problem. 4) Swap the
speaker output wire from left to right. If the problem changes sides then you have a bad speaker cable, passive
crossover network and/or speaker.
Crossover Control
AMP 1
Crossover Control
AMP 2
4. CrossoverControl The setting for this control is subjective; 80Hz is a good place to start.
5. RemoteBass(Level Control) When using the remote bass level control you have the ability to
control the level of the Subwoofer Channel’s output remotely. To mount the remote bass level control,
simply screw the metal bracket to the
Figure 6
Mount the metal bracket
chosen location. Then slide the
Back
View
Side View
housing onto the bracket until it
snaps into place. Run the cable from
the controller to the “Remote Bass”
jack on the amplifier chassis.
Slide the housing until it snaps into the metal bracket
No Fader? When using both sets of high-level inputs (ZX700.5 only), RCA dummy plugs must be inserted into
the RCA AMP 2 inputs in order for the fader to work properly. If you do not have dummy plugs available, use
unterminated RCA ends or cut the ends off of existing RCA cable. Do not use shorting plugs.
If you have more questions about the installation or operation of your new KICKER product, see the Authorized KICKER Dealer where you
made your purchase. For more advice on installation, click on the SUPPORT tab on the Kicker homepage, www.kicker.com. Choose the
TECHNICAL SUPPORT tab, choose the subject you are interested in, and then download or view the corresponding information. Please
E-mail support@kicker.com or call Technical Services (405) 624-8583 for unanswered or specific questions.
Please Note: Modern high performance speakers have a lower DC Resistance than what used to be available. The Kicker Coaxial and
Component speakers are rated at four ohms (some DC Resistances may be as low as 3 ohms) and work with any amplifier designed to
operate at a four ohm load. If you want to use two Kicker Coaxial or Component speakers on a single channel of your amplifier wire the
speakers in series. This will improve the sound quality, lower the total harmonic distortion and lessen the thermal load at the amplifier. This
may prevent an amplifier from shutting down, due to over-current protection circuitry.
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct. Improper connections can
result in blown amplifier fuses as well as the failure of other critical systems in the vehicle.
Performance
Model
ZX550.3
ZX700.5
@14.4V, 4Ω Stereo ≤1% THD+N
70 x 2
70 x 4
@14.4V, 2Ω Stereo, ≤1% THD+N
85 x 2
85 x 4
@14.4V, 4Ω Mono, ≤1% THD+N
N/A
165 x 2
210 x 1
RMS Power in Watts, AMP 1 and AMP 2 all channels driven
@14.4V, 4Ω Mono ≤1.5% THD+N
210 x 1
If your amplifier does not appear to be
working, check the obvious things first
such as blown fuses, poor or incorrect
wiring connections, incorrect setting of
4 Conductor
crossover switch and gain controls, etc.
Phone Cable
There are two LEDs on the top of your
Kicker ZX series amplifier, one green and
one red. When the green LED is lit this indicates the amplifier is turned on and no trouble exists. If the green LED turns
off and the red LED is lit, this indicates that the protection circuitry (SORT) is engaged.
@14.4V, 2Ω Mono, ≤1.5% THD+N
420 x 1
420 x 1
16 3/4” (425mm)
20” (507mm)
Green LED off, no output? With a Volt Ohm Meter (VOM) check the following: 1) +12 volt power terminal
(should read +12V to +16V) 2) Remote turn-on terminal (should read +12V to +16V) 3) Check for reversed power
and ground connections 4) Ground terminal, for proper conductivity
Electronic Crossover:
Length:
SUB INPUT
SUB
Green LED on, no output? Check the following: 1) RCA connections 2) Test speaker outputs with a “known”
good speaker. 3) Substitute source unit with a “known” good source unit. 4) Check for a signal in the RCA cable
feeding the amplifier with the “AC” test position selected on the VOM meter.
Red LED on, no output? 1) Amplifier is very hot. Thermal protection is engaged. Test for proper impedance at
the speaker terminals with a VOM meter (see the diagrams in this manual for minimum recommended impedance and
multiple speaker wiring suggestions). Also check for adequate airflow around the amplifier. 2) Amplifier shuts down
only while vehicle is running. Voltage protection circuitry is engaged. Voltage to the amplifier is not within the 9-16
volt operating range. Have the vehicle's charging and electrical system inspected. 3) Amplifier will only play at low
4
ZX.3/ZX.5AMPLIFIER
Specifications common to all models:
Height:
2 1/8” (54mm)
Width:
9 5/8” (244mm)
Frequency Response, ± 0.5 dB:
Signal-to-Noise Ratio:
Input Sensitivity:
PERFORMANCE
RMS Power in Watts, Subwoofer channel driven
TroubleShooting
20 Hz - 20 kHz
>95 dB, a-weighted, re: rated power
125 mV - 5 V low level, 250 mV - 10 V high level
Variable (defeatable) HI pass, 50 - 200Hz, 12bB per octave, for the full-range channels
Variable LOW pass, 50 - 200Hz, 24dB per octave, for the subwoofer channel
Bass Boost:
Variable 0 to +18dB boost @ 40Hz, for the subwoofer channel
Model ZX550.3
70 x 2, 210 x 1 @ 4 ohms from 20-20K, 20-200Hz, 14.4Vdc,
1% THD, CEA-2006 (Watts)
Signal to Noise Ratio -72 / -55 dBA CEA-2006 (ref: 1W, A-weighted)
Model ZX700.5
70 x 4, 210 x 1 @ 4 ohms from 20-20K, 20-200Hz, 14.4Vdc,
1% THD, CEA-2006 (Watts)
Signal to Noise Ratio -72 / -55 dBA CEA-2006 (ref: 1W, A-weighted)
5
WARRANTY
ElectronicsLimitedWarranty
InternationalWarranty
Kicker warrants this product to be free from defects in material and workmanship under normal use for a period of
THREE (3) MONTHS from date of original purchase with receipt. When purchased from an Authorized KICKER Dealer
it is warranted for TWO (2) YEARS from date of original purchase with receipt. In all cases you must have the original
receipt. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction
during the warranty period, Kicker will repair or replace (at its discretion) the defective merchandise with equivalent
merchandise at no charge. Warranty replacements may have cosmetic scratches and blemishes. Discontinued
products may be replaced with more current equivalent products.
Contact your International Kicker dealer or distributor concerning specific procedures for your country's warranty
policies.
This warranty is valid only for the original purchaser and is not extended to owners of the product subsequent to the
original purchaser. Any applicable implied warranties are limited in duration to a period of the express warranty as
provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or
implied, shall apply to this product thereafter. Some states do not allow limitations on implied warranties; therefore
these exclusions may not apply to you. This warranty gives you specific legal rights; however you may have other
rights that vary from state to state.
GARANTÍA INTERNACIONAL
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE
Defective merchandise should be returned to your local Authorized Stillwater Designs (Kicker) Dealer for warranty
service. Assistance in locating an Authorized Dealer can be found at www.kicker.com or by contacting Stillwater
Designs directly. You can confirm that a dealer is authorized by asking to see a current authorized dealer window
decal.
If it becomes necessary for you to return defective merchandise directly to Stillwater Designs (Kicker), call the Kicker
Customer Service Department at (405) 624-8510 for a Return Merchandise Authorization (RMA) number. Package all
defective items in the original container or in a package that will prevent shipping damage, and return to:
WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing!
Turning up a system to a level that has audible distortion is more damaging to your ears than listening to an
undistorted system at the same volume level. The threshold of pain is always an indicator that the sound level is too
loud and may permanently damage your hearing. Please use common sense when controlling volume.
VersiónEspañol
Comuníquese con su concesionario o distribuidor Kicker internacional para obtener infor ación sobre procedimientos
específicos relacionados con las normas de garantía de su país.
ADVERTENCIA: Los excitadores Kicker son capaces de producir niveles de sonido que pueden dañar
permanentemente el oído. Subir el volumen del sistema hasta un nivel que produzca distorsión es más dañino para el
oído que escuchar un sistema sin distorsión al mismo volumen. El dolor es siempre una indicación de que el sonido es
muy fuerte y que puede dañar permanentemente el oído. Sea precavido cuando controle el volumen.
La frase "combustible para vivir la vida Livin' Loud™ a todo volumen" se refiere al entusiasmo por la vida que la marca
Kicker de estéreos de automóvil representa y a la recomendación a nuestros clientes de que vivan lo mejor posible ("a
todo volumen") en todo sentido. La línea de altavoces y amplificadores Kicker es la mejor del mercado de audio de
automóviles y por lo tanto representa el "combustible" para vivir a todo volumen en el área de "estéreos de automóvil"
de la vida de nuestros clientes. Recomendamos a todos nuestros clientes que obedezcan todas las reglas y
reglamentos locales sobre ruido en cuanto a los niveles legales y apropiados de audición fuera del vehículo.
INTERNATIONALE GARANTIE
DeutscheVersion
Stillwater Designs, 5021 North Perkins Road, Stillwater, OK 74075
The RMA number must be clearly marked on the outside of the package. Please return only defective components.
The return of functioning items increases your return freight charges. Non-defective items will be returned freightcollect to you.
Include a copy of the original receipt with the purchase date clearly visible, and a "proof-of-purchase" statement listing
the Customer's name, Dealer's name and invoice number, and product purchased. Warranty expiration on items
without proof-of-purchase will be determined from the type of sale and manufacturing date code. Freight must be
prepaid; items sent freight-collect, or COD, will be refused.
WHAT IS NOT COVERED?
HOW LONG WILL IT TAKE?
Kicker strives to maintain a goal of 72-hour service for all electronics (amplifiers, crossovers, equalizers, etc.) returns.
Delays may be incurred if lack of replacement inventory or parts is encountered.
WARNUNG: KICKER-Treiber können einen Schallpegel erzeugen, der zu permanenten Gehörschäden führen kann!
Wenn Sie ein System auf einen Pegel stellen, der hörbare Verzerrungen erzeugt, schadet das Ihren Ohren mehr, als ein
nicht verzerrtes System auf dem gleichen Lautstärkepegel. Die Schmerzschwelle ist immer eine Anzeige dafür, dass
der Schallpegel zu laut ist und zu permanenten Gehörschäden führen kann. Seien Sie bei der Lautstärkeeinstellung
bitte vernünftig!
Der Slogan "Treibstoff für Livin' Loud" bezieht sich auf die mit den Kicker-Autostereosystemen assoziierte
Lebensfreude und die Tatsache, dass wir unsere Kunden ermutigen, in allen Aspekten ihres Lebens nach dem Besten
("Livin' Loud") zu streben. Die Lautsprecher und Verstärker von Kicker sind auf dem Markt für Auto-Soundsysteme
führend und stellen somit den "Treibstoff" für das Autostereoerlebnis unserer Kunden dar. Wir empfehlen allen unseren
Kunden, sich bezüglich der zugelassenen und passenden Lautstärkepegel außerhalb des Autos an die örtlichen
Lärmvorschriften zu halten.
GARANTIE INTERNATIONALE
VersionFrançaise
Pour connaître les procédures propres à la politique de garantie de votre pays, contactez votre revendeur ou
distributeur International Kicker.
GARANTIE
This warranty is valid only if the product is used for the purpose for which it was designed.
It does not cover:
o Damage due to improper installation
o Subsequent damage to other components
o Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or UV radiation
o Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be
considered abuse
o Any cost or expense related to the removal or reinstallation of product
o Speakers damaged due to amplifier clipping or distortion
o Items previously repaired or modified by any unauthorized repair facility
o Return shipping on non-defective items
o Products with tampered or missing barcode labels
o Products returned without a Return Merchandise Authorization (RMA) number
o Freight Damage
o The cost of shipping product to Kicker
o Service performed by anyone other than Kicker
Nehmen Sie mit Ihren internationalen Kicker-Fachhändler oder Vertrieb Kontakt auf, um Details über die
Garantieleistungen in Ihrem Land zu erfahren.
AVERTISSEMENT: Les haut-parleurs Kicker ont la capacité de produire des niveaux sonores pouvant endommager
l'ouïe de façon irréversible ! L'augmentation du volume d'un système jusqu'à un niveau présentant une distorsion
audible endommage davantage l'ouïe que l'écoute d'un système sans distorsion au même volume. Le seuil de la
douleur est toujours le signe que le niveau sonore est trop élevé et risque d'endommager l'ouïe de façon irréversible.
Réglez le volume en faisant prevue de bon sens !
L'expression " carburant pour vivre plein pot " fait référence au dynamisme de la marque Kicker d'équipements audio
pour véhicules et a pour but d'encourager nos clients à faire le maximum (" vivre plein pot ") dans tous les aspects de
leur vie. Les haut-parleurs et amplificateurs Kicker sont les meilleurs dans le domaine des équipements audio et
représentent donc pour nos client le " carburant pour vivre plein pot " dans l'aspect " installation audio de véhicule "
de leur vie. Nous encourageons tous nos clients à respecter toutes les lois et réglementations locales relatives aux
niveaux sonores acceptables à l'extérieur des véhicules.
Failure to follow these steps may void your warranty. Any questions can be directed to the Kicker Customer Service
Department at (405) 624-8510.
P.O. Box 459 • Stillwater, Oklahoma 74076 • U.S.A. • (405) 624-8510
6
ZX.3/ZX.5AMPLIFIER
04272006+06ZX.4
7
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2006:04:27 10:32:51-05:00 Create Date : 2006:04:27 10:31:29-05:00 Metadata Date : 2006:04:27 10:32:51-05:00 Format : application/pdf Title : TEMP 2006 ZX550-3 700-5 4in1 a01.qxp Creator : bcganz Document ID : uuid:066374a2-677a-47b5-b294-28c13f602d5c Instance ID : uuid:35a1875a-2809-4a89-a20c-d98d6dda24f0 Has XFA : No Page Count : 4 Author : bcganzEXIF Metadata provided by EXIF.tools