Kidde 1 Users Manual AU_SupraRapidEntryMountingInstructions
Kidde-1-Brochure-748766 kidde-1-brochure-748766
2015-06-12
: Kidde Kidde-1-Users-Manual-748768 kidde-1-users-manual-748768 kidde pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Rapid Entry Systems P/N 10102664P1 • Feb 2013 © 2013 Kidde. All rights reserved. Installation Instructions Introduction Your SupraSafe is the latest in Rapid Entry key control. To fully utilize it’s built-in security features, we recommend that reasonable care be given to the location and method of mounting. The vault is coated with a tough, baked polyurethane abuse; however, it is always best to locate the vault in an area which is sheltered from excessive moisture and possible mechanical damage. Important! Contact your local department for mounting location and instructions. 6. once the vault has been installed. 7. We strongly recommend the wiring of the tamper or licensed electrician. The circuit shall conform to NEC class 2 or 3, or UL class 634 standards. In no case shall the wiring supply more than 30 volts at 50 ma. Consult local codes and ordinances prior to installations. Figure 1. Side View of Mounted Vault Installation for Supra-Max, SupraSafe 1, SupraSafe 2HS/2HSR, and SupraSafe 2HS/TS-Vault 1. Mount the vault so that the moisture drain hole is on the bottom. 2. Use a level to plumb the vault square. 3. Four 5/16-inch lag bolts have been provided for surface mounting the vault. Important! When installing the vault, do not over-tighten the four mounting bolts as this may distort the outside shell of the vault. 4. To secure the vault to a masonry/brick wall, it is necessary to use the anchors provided with the 5/16 lag bolts mounting kit. Drill a 1/2” hole approximately 1-3/4” deep into the masonry/brick wall. It is recommended to use a carbide/masonry bit to prevent cracking or shattering. Gently pound the anchor into the hole with a hammer so that it is Drain hole 5. Caulk between the vault and the wall for better Chain mounting bracket Instructions for SupraSafe 2HSR and SupraSafe 2HSR/TS Vaults The SupraSafe 2HSR and SupraSafe 2HSR/TS vaults are designed to be recessed into a wall for attractive flush mounting. These units can be adapted to fit a variety of hollow wall situations or can be installed in a sold concrete wall which has been cored to a six inch diameter. For concrete or masonry walls in new construction, we recommend the use of our Cast-inPlace Mounting Kit described below. studs within the vault. Do not over-tighten mounting nuts as this may distort outside flange. 3. Slip the chain mounting bracket (attached to the chain-lid assembly) over the lower right-hand stud prior to installing the bottom washers and nuts in the vault. This will permanently attach the lid to the vault. 4. Please contact your fire department to install the lid once the vault has been installed. Figure 2. Cast-in-Place Mounting Kit and Side View of Installation With the SupraSafe 2HSR/TS, removal of the tamper switch is not necessary during installation. The alarm wiring to the tamper switch should be pulled tight so that any attempt to force the vault out of the wall will break the wire or pull terminals loose. Push-On type terminals are supplied for connection to tamper switch. Tamper switch can be connected for either open or closed circuits. Rebar Cast-in-Place Mounting Kit (P/N: 454000) The Cast-in-Place Mounting kit is used only with the SupraSafe 2HSR and SupraSafe 2HSR/TS vaults. The kit contains a shell housing and mounting hardware to be cast in place in new masonry or concrete construction. After construction is completed, the vault mounts inside the recessed shell housing so that the small moisture drain hole is on the bottom. Face plate Installation Tamper switch adjusting screw The mounting kit may be fastened to the inside wall of a concrete form or set in place during construction of a masonry wall. Wiring conduit may be connected through one of several knockout holes in shell housing. The orientation of the mounting kit requires that the rebar on the backplate be horizontal. Mount the housing shell to the backplate so that the tamper switch adjustment screw is on the left side of the housing. Important! Care should be taken to insure that the front of the shell housing, including the cover plate and screw heads, is flush with finish wall. Shell housing should be plumbed with a level. Leave cover and screws in place until vault is ready to be mounted inside. Four mounting studs are provided for securing the vault and chain-lid assembly within the housing shell. 1. Place vault in housing shell of mounting kit so that the vault’s small moisture drain hole is on the bottom. Align the tamper switch of the vault with the tamper switch adjustment screw of the housing shell. The tamper switch adjustment screw has a slotted head to adjust for proper switch operation. 2. Install washers and nuts onto the two top mounting Tamper Switch (2HSR/TS, 2HS/TS only) SupraSafe 2HSR or 2HSR/TS Vault Drain hole Cast-in-Place Mounting Kit Adjusting screw tamper switch
Source Exif Data:
File Type : AI File Type Extension : ai MIME Type : application/vnd.adobe.illustrator PDF Version : 1.6 Linearized : Yes Create Date : 2011:08:25 15:52:21-07:00 Creator : Adobe InDesign CS5 (7.0.4) Modify Date : 2013:02:28 15:18:13-05:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Instance ID : uuid:cba65b2c-67b6-ed40-822a-d19800b5af29 Document ID : adobe:docid:indd:cfd9b3c2-56d2-11de-977a-8ddeb7e08c8c Original Document ID : adobe:docid:indd:cfd9b3c2-56d2-11de-977a-8ddeb7e08c8c Rendition Class : proof:pdf History Action : saved, saved, saved, saved History Instance ID : xmp.iid:DE00A37E5B22E011AA6AE8AC9329C711, xmp.iid:DF00A37E5B22E011AA6AE8AC9329C711, xmp.iid:E000A37E5B22E011AA6AE8AC9329C711, xmp.iid:043DE097D428E0118D80F4BF4093FD70 History When : 2011:01:17 17:03:10-08:00, 2011:01:17 17:03:10-08:00, 2011:01:17 17:11:54-08:00, 2011:01:25 14:43:56-08:00 History Software Agent : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0 History Changed : /, /metadata, /, / Metadata Date : 2013:02:28 15:18:13-05:00 Creator Tool : Adobe InDesign CS5 (7.0.4) Thumbnail Width : 256 Thumbnail Height : 212 Thumbnail Format : JPEG Thumbnail Image : (Binary data 16521 bytes, use -b option to extract) Doc Change Count : 83 Format : application/pdf Producer : Adobe PDF Library 9.9 Trapped : False N Pages : 1 Has Visible Transparency : False Has Visible Overprint : True Max Page Size W : 8.500000 Max Page Size H : 11.000000 Max Page Size Unit : Inches Font Name : Arial-BoldItalicMT, Arial-BoldMT, Arial-ItalicMT, ArialMT, Frutiger-Roman, Frutiger-Bold, FrutigerLTStd-Roman, GEInspira-Bold Font Family : Arial, Arial, Arial, Arial, Frutiger, Frutiger, Frutiger LT Std, GE Inspira Font Face : Bold Italic, Bold, Italic, Regular, 55 Roman, 65 Bold, 55 Roman, Bold Font Type : TrueType, TrueType, TrueType, TrueType, Type 1, Type 1, Open Type, TrueType Font Version : Version 2.90, Version 2.90, Version 2.90, Version 2.60, 001.000, 001.000, Version 2.100;PS 005.000;hotconv 1.0.67;makeotf.lib2.5.33168, Version 1.10 Font Composite : False, False, False, False, False, False, False, False Font File Name : Arial, Arial, Arial, ArialMT TrueType, FrutiRom; BLI Frutiger BlackItalic, FrutiBol; Fruitiger, FrutigerLTStd-Roman.otf, GEInspiraBd.TTF Plate Names : Cyan, Magenta, Yellow, Black Swatch Group Name : Default Swatch Group Swatch Group Type : 0 Page Count : 2 For : Ilsa Spaan, Title : AU_SupraRapidEntryMountingInstructions.pdf Bounding Box : -267 35 612 759 Container Version : 11 Creator Version : 15EXIF Metadata provided by EXIF.tools