Kidde Firex Adc 4518 4618 5000 English 110762F Owner S Manual 110 762F
2014-07-06
: Kidde Kidde-Firex-Adc-4518-4618-5000-English-110762F-Owner-S-Manual kidde-firex-adc-4518-4618-5000-english-110762f-owner-s-manual kidde pdf
Open the PDF directly: View PDF .
Page Count: 8
![](asset-1.png)
1
SMOKE ALARM FEATURES
•Features False Alarm Control which, when activated, quiets unwant-
ed alarms for up to 15 minutes.
•This smoke alarm is powered by 120V AC and a 9-volt battery
back-up source. AC/DC smoke alarms offer added protection in the
event of a power failure or a drained battery.
•Unique power connector prevents interconnection with incompatible
smoke alarms or security systems.
•This smoke alarm may be interconnected with as many as 11 other
Firex model AD, ADC and PAD smoke alarms, or as many as 6
Firex model ADH heat alarms for a total of not more than 18
interconnected devices.
•Optional tamper-resist feature can safeguard against tampering.
•Unique “battery missing” signal. The smoke alarm will not attach to
the mounting bracket if a battery is not in the battery pocket.
•Improperly connected or weak battery signal. The smoke alarm will
sound a short beep about once a minute if the battery is weak or
improperly connected. The red LED will blink 4 times per minute to
help identify the alarm with the weak battery.
•Separate green and red LEDs indicate whether the smoke alarm is
receiving AC and DC power, working under normal operation, in
alarm, or under false alarm control.
•Loud alarm horn—85 decibels at 10 feet—alerts you to an emergency.
•Test button checks smoke alarm operation.
• Latching LED - the red LED blinks 3 times per minute on the unit
that initiates the alarm.
• Ramp-up test horn that emits 2 reduced-volume beeps before
reaching the full 85db level during testing.
IMPORTANT SAFETY INFORMATION
PLEASE RED AND SAVE THESE
INSTURCTIONS
WARNING
•This smoke alarm requires constant 120-volt, AC power AND a
working 9-volt battery to operate properly. This smoke alarm WILL
NOT work if AC power is not connected or has been interrupted for any
reason AND the battery is removed, drained (a beep once per minute
indicates a drained battery) or improperly connected. DO NOT use any
other kind of battery except as specified in this manual. DO NOT con-
nect this smoke alarm to any other type of smoke alarm or auxiliary
device, except those listed in this manual.
•DO NOT remove or disconnect battery or turn off AC power to
quiet unwanted alarms. This will remove your protection. This
smoke alarm features a False Alarm Control button which, when
activated, will quiet unwanted alarms for up to 15 minutes.
•The Push-to-Test button accurately tests all smoke alarm
functions. DO NOT use any other test method. Test smoke alarm
weekly to ensure proper operation.
•This smoke alarm should be installed only by a licensed,
qualified electrician. Observe and follow all local and national
electrical and building codes for installation.
•This smoke alarm IS NOT designed to be the PRIMARY protec-
tion for buildings that require complete fire alarm systems.
Buildings of this type include hotels, motels, dormitories, hospitals,
IONIZATION
MODEL ADC
120V AC
Smoke Alarm
with 9V Battery
Back-up
110-762F
S
T
A
T
E
O
F
C
A
L
I
F
O
R
N
I
A
S
T
A
T
E
F
I
R
E
M
A
R
S
H
A
L
L
I
S
T
I
N
G
S
E
R
V
I
C
E
PLEASE READ AND SAVE
THIS MANUAL
Installer: Please leave this
manual with the product.
The ionization type alarms are generally more effective at detecting fast, flaming
fires which consume combustible materials rapidly and spread quickly. Sources of
these fires may include flammable liquids or paper burning in a waste container.
The photoelectric type alarms are generally more effective at detecting slow,
smoldering fires which smolder for hours before bursting into flame. Sources of
these fires may include cigarettes burning in couches or bedding. However, both
types of alarms are designed to provide adequate detection of both types of fires.
If you desire the benefits of both systems, you should install smoke alarms that
combine in one alarm both photoelectric and ionization sensing technologies.
!
110-762F English 12/12/06 4:06 PM Page 1
![](asset-2.png)
2
nursing homes, and group homes. This is true even if they were once
single family homes. However, this smoke alarm MAY be used
inside individual rooms as SUPPLEMENTAL protection.
•Install a smoke alarm in every room and on every level of the
home. Smoke may not reach the smoke alarm for many reasons. For
example, if a fire starts in a remote part of the home, on another
level, in a chimney, wall, roof, or on the other side of a closed door,
smoke may not reach the smoke alarm in time to alert household
members. A smoke alarm will not promptly detect a fire EXCEPT in
the area or room in which it is installed.
•Interconnected smoke alarms installed in every room and on
every level of the household offers maximum protection. The
National Fire Protection Agency (NFPA) recommends interconnecting
smoke alarms so that when one smoke alarm senses smoke and
sounds its alarm, all others will sound as well. Do not interconnect
smoke alarms from one individual family living unit to another. Do not
connect this smoke alarm to any other type of alarm or auxiliary device.
•Smoke alarms may not alert every household member every
time. There may be limiting circumstances where a household
member may not hear the alarm (e.g., outdoor or indoor noise,
sound sleepers, drug or alcohol usage, the hard of hearing, etc.). If
you suspect that this smoke alarm may not alert a household mem-
ber, install and maintain specialty smoke alarms. Current studies
have shown smoke alarms may not awaken all sleeping individuals,
and that it is the responsibility of individuals in the household that
are capable of assisting others to provide assistance to those who
may not be awakened by the alarm sound, or to those who may be
incapable of safely evacuating the area unassisted.
•Smoke alarms must not be used with detector guards unless
the combination of alarm and guard has been evaluated and found
suitable for that purpose.
•Smoke alarms can only sound their alarms when they detect
smoke. Smoke alarms detect combustion particles in the air. They
do not sense heat, flame, or gas. This smoke alarm is designed to
give audible warning of a developing fire. However, many fires are
fast-burning, explosive, or intentional. Others are caused by care-
lessness or safety hazards. Smoke may not reach the smoke alarm
QUICKLY ENOUGH to ensure safe escape.
•Smoke alarms have limitations. This smoke alarm is not fool-
proof and is not warranted to protect lives or property from fire.
Smoke alarms are not a substitute for insurance. Homeowners and
renters should insure their life and property. In addition, it is possi-
ble for the smoke alarm to fail at any time. For this reason, you
must test the smoke alarm weekly and replace every 10 years.
SMOKE ALARM PLACEMENT
Invensys Controls Americas recommends complete coverage pro-
tection achieved by installing a smoke alarm in every room of your
home. The National Fire Protection Association’s (NFPA) minimum
requirement, as stated in Standard 72, Chapter 2, reads as follows:
“2-2.1.1.1 Smoke detectors shall be
installed outside of each separate sleep-
ing area in the immediate vicinity of the
bedrooms and on each additional story of
the family living unit including basements
and excluding crawl spaces and unfin-
ished attics. In new construction a smoke detector
also shall be installed in each sleeping room.”
Chapter 2, also reads as follows:
“2-2.2.1 In new construction, where more than
one smoke detector is required by 2-2.1, they
shall be so arranged that operation of any smoke
detector shall cause the alarm in all smoke detec-
tors within the dwelling to sound.”
The NFPA, 1993 Edition, Appendix
A further states:
“The required number of smoke
detectors may not provide reliable
early warning protection for those areas separated by a door from
the areas protected by the required smoke detectors. For this rea-
son, it is recommended that the householder consider the use of
additional smoke detectors for those areas for increased protec-
tion. The additional areas include: basement, bedrooms, dining
room, furnace room, utility room, and hallways not protected by
the required smoke detectors.”
Also, as required by the California State Fire Marshal:
“Early warning fire detection is best achieved by the installation of
fire detection equipment in all rooms and areas of the household
as follows: A smoke detector installed in each separate sleeping
area (in the vicinity, but outside the bedrooms), and heat or
smoke detectors in the living rooms, dining rooms, bedrooms,
kitchens, hallways, attics, furnace rooms, closets, utility and
storage rooms, basements and attached garages.”
TV ROOM
DINING
ROOM KITCHEN BEDROOM
BEDROOM
BEDROOM
LIVING ROOM
KITCHEN
DINING
ROOM
BEDROOM BEDROOM
BEDROOM
LIVING ROOM
BEDROOM BEDROOM
LIVING
ROOM
DINING
ROOM
BASEMENT
HALL
110-762F English 12/12/06 4:06 PM Page 2
![](asset-3.png)
3
FOR BEST PROTECTION, WE
RECOMMEND THAT YOU INSTALL
A SMOKE ALARM IN EVERY ROOM
In addition, we recommend that all smoke alarms be interconnected.
Typical Efficiency
Home (Apartment)
• Install a smoke alarm on the
ceiling or wall closest to the
sleeping area.
Typical Mobile Home
NOTE: For mobile homes built before 1978, install smoke alarms on
an inside wall between 4 and 12 inches from the ceiling. (Older
mobile homes have little or no insulation in the ceiling.) This is
especially important if the ceiling is unusually hot or cold.
•Install a smoke alarm inside each bedroom and in the hallway
outside each separate sleeping area.
Typical Single Story Home
•Install a smoke alarm on the ceiling
or wall inside each bedroom and in
the hallway outside each separate
sleeping area. If a bedroom area
hallway is more than 30 feet long,
install a smoke alarm at each end.
If there is a basement:
•Install a smoke alarm on the
basement ceiling at the bottom of
the stairwell.
Typical Two-Story or Split Level
Home
•Install a smoke alarm on the ceiling
or wall inside each bedroom and in
the hallway outside each separate
sleeping area. If a bedroom area hall-
way is more than 30 feet long, install
a smoke alarm at each end.
•Install a smoke alarm at the top of
a first-to-second floor stairwell.
If there is a basement:
•Install a smoke alarm on the
basement ceiling at the bottom
of the stairwell.
IMPORTANT SMOKE ALARM
PLACEMENT AND EXCEPTION
INFORMATION:
•Install a smoke alarm as close to the
center of the ceiling as possible. If
this is not practical, mount no closer
than 4 inches from a wall or corner.
Also, if local codes allow, install
smoke alarms on walls, between 4
and 12 inches from ceiling/wall inter-
sections.
•Install a minimum of two smoke alarms in every home, no
matter how small the home. New construction codes require
a minimum of two interconnected smoke alarms in newly built
homes.
•Install a smoke alarm in each room
that is divided by a partial wall (either
coming down from the ceiling at least
24 inches, or coming up from the
floor).
•Install smoke alarms on peaked,
cathedral, or gabled ceilings
3 feet from the highest point
(measured horizontally).
•Install a smoke alarm in lived-in attics
or attics which house electrical equip-
ment like furnaces, air conditioners,
or heaters.
SINGLE STORY
BEDROOM BED-
ROOM BATH
BASEMENT FURNACE
ROOOM
KITCHEN
TWO STORY
BEDROOM BEDROOMBATH
LIVED-IN
ATTIC
LIVING AREA KITCHEN
BASEMENT
FURNACE
ROOM
Key
• Smoke Alarm (Ionization)
ΔIonization Smoke Alarm with False Alarm Control
or Photoelectric Smoke Aarm
24"
STUB WALL
SOFFIT
3'-0"
PEAKED CEILING
Acceptable
in this area
4 IN
(0.1m )
4 IN
(0.1m )
MINIMUM
12 IN
(0.3 m )
MAXIMUM
CEILING
SIDE
WALL
ACCEPTABLE HERE
NEVER HERE
TOP OF DETECTOR
ACCEPTABLE HERE
EFFICIENCY APARTMENT
SLEEPING
AREA
KITCHEN
LIVING
AREA
BEDROOM BATH KITCHEN LIVING ROOM MOBILE HOME
110-762F English 12/12/06 4:06 PM Page 3
![](asset-4.png)
4
DO NOT install smoke alarm:
Near appliances or areas where normal combustion
regularly occurs (kitchens, near furnaces, hot water
heaters). Use specialized smoke alarms with unwanted
alarm control for these areas.
In areas with high humidity, like bathrooms or areas
near dishwashers or washing machines. Install at least
10 feet (3 meters) away from these areas, if possible.
Near air returns or heating and cooling supply vents.
The air could blow smoke away from the detector,
interrupting its alarm.
In rooms where temperatures may fall below 40˚F
(4˚ C) or rise above 100˚F (38˚C).
In extremely dusty, dirty, or insect-infested areas.
Loose particles interfere with smoke alarm operation.
HOW TO INSTALL
THIS SMOKE ALARM
DANGER: ELECTRICAL SHOCK HAZARD. Turn
off power at the main fuse box or cir-
cuit breaker by removing the fuse or
switching the circuit breaker to the
OFF position.
WARNING: This smoke alarm should be installed
only by a qualified electrician. Smoke
alarm wiring to be used shall be in
accordance with the provisions of
Article 210 and 760 of the National
Electrical Code, ANSI/NFPA 70, and
any local codes that may apply.
Interconnect wire location shall be in
accordance with NEC Article 300.3b.
THIS SMOKE ALARM SHOULD BE INSTALLED IN ACCOR-
DANCE WITH THE NATIONAL FIRE PROTECTION ASSOCIA-
TION’S STANDARD 72 (National Fire Protection Association,
Batterymarch Park, Quincy, MA 02269).
• Install smoke alarm on a 4-inch
octagon or single gang junction
box only.
1. From back of smoke alarm,
remove mounting plate. (To later
engage tamper-resist feature,
twist out and set aside one of
the pins molded into the plate.
Both pins are exactly the same.)
2. Align recessed slots on plate
with mounting holes of a 4-inch
octagon or single gang junction
box.
3. Gently pull household wires
through center hole of plate.
4. Secure plate to junction box using mounting screws.
5. With a small wire connector, connect white wire from connector
plug to white household wire.
6. Connect black wire from connector plug to black household wire.
7. If interconnection is desired, connect yellow wire from connec-
tor to interconnect wire between smoke alarms. See section,
INTERCONNECTING SMOKE ALARMS.
NOTE: If this will be a single-station smoke alarm, cover yellow
wire with electrical tape and tuck into junction box.
8. Lift open battery pocket door.
9. Connect new 9-volt battery to battery connector inside battery
pocket. BE SURE BATTERY IS
SECURELY CONNECTED. Smoke
alarm may beep briefly when bat-
tery is installed.
10. Close battery pocket door, snap-
ping it into place. (For tamper-
resist, use long-nosed pliers to
remove thin plastic from notch on
smoke alarm edge.)
11. Attach connector plug to pins on
back of smoke alarm. Plug will only
fit one way and will snap into place.
12. Gently tug connector to be sure it is attached securely.
!
!
Remove thin
plastic from notch.
110-762F English 12/12/06 4:06 PM Page 4
![](asset-5.png)
5
13. Position smoke alarm to mounting plate and turn clockwise to
lock into place. (To engage tamper resist feature, insert pin
into notch on edge of smoke alarm after smoke alarm is posi-
tioned properly in base. Refer to step #10 on previous page.)
NOTE: Smoke alarm will not mount to plate if battery is not installed.
14. Turn on power at main fuse box or circuit breaker.
15. Test smoke alarm. See TESTING THE SMOKE ALARM.
INTERCONNECTING
SMOKE ALARMS
•This smoke alarm may be interconnected with as many as
11 other Firex model AD, ADC and PAD smoke alarms, or as
many as 6 Firex model ADH heat alarms for a total of not more
than 18 interconnected devices. DO NOT connect to any other
type or model smoke alarm.
•Connect smoke alarms to a single AC branch circuit. If local
codes do not permit, be sure the neutral wire is common to both
phases.
RED AND GREEN LED INDICATORS
This smoke alarm features separate red and green LED indicators.
The LEDs indicate the following:
GREEN LED
ON — AC power is present.
OFF — AC power is not present.
RED LED — can be seen through the push
to test button.
Blinks once a minute — indicating normal operation.
Blinks once a second — smoke alarm senses smoke and
simultaneously sounds an audi-
ble alarm.
Blinks once every 10 seconds — smoke alarm is quieting an
unwanted alarm.
Blinks 3 times per minute — Indicates this unit initiated an
alarm in an interconnected
system (press the TEST button
to reset).
Blinks 4 times per minute — Indicates weak or improperly
connected battery.
(Interconnected system only):
OFF — another smoke alarm in the network has sensed
smoke and is signalling this alarm.
FALSE ALARM CONTROL
Model ADC features a False Alarm Control that, when activated,
quiets unwanted alarms for up to 15 minutes.
To use the False Alarm Control:
Press and release the test button during an unwanted alarm. The
alarm should stop within ten seconds. This means the smoke alarm
is in False Alarm Control. In an interconnected system, the red LED
on the initiating alarm will continue to blink until reset by pressing
the TEST button.
If the smoke alarm does not go into False Alarm Control and contin-
ues to sound its loud alarm horn, or if it initially goes into False Alarm
Control then resounds the alarm, the smoke is too heavy and could
be a possibly dangerous situation — take emergency action.
TESTING THE
SMOKE ALARM
WARNING
•Test each smoke alarm to be sure it is installed correctly and
operating properly.
Insert pin here
!
WHITE WHITE WHITE
YELLOW YELLOW
BLACK BLACK BLACK
TO NEUTRAL
TO 120 VAC
110-762F English 12/12/06 4:06 PM Page 5
![](asset-6.png)
6
•Test all smoke alarms in an interconnected system after
installation.
•The Push-to-Test button accurately tests all functions. DO NOT
use an open flame to test this smoke alarm. You may ignite and
damage the smoke alarm or your home.
•Test smoke alarms weekly and upon returning from vacation or
when no one has been in the household for several days.
•Stand at arm’s length from the smoke alarm when testing. The
alarm horn is loud to alert you to an emergency and can be
harmful to hearing.
FIELD TESTING IMPORTANT NOTICE:
When testing is required in the field by local inspectors or other
parties, it should be done using only the Smoke Detector
Sensitivity Analyzer model #501-1 manufactured by Gemini
Scientific Corporation. Follow the Gemini test and set-up instruc-
tions provided by the manufacturer, and use the obscuration limits
provided on the back of the smoke alarm. Refer to the smoke
alarm’s instruction manual for maintenance and push-to-test
operation.
Go / No-Go Testing
A functional Go / No-Go test can be performed on the unit by using
Smoke Detector Teste model #25S, manufactured for Home
Safeguard Industries, Inc. Follow the instructions included on the
tester.
Test all smoke alarms weekly by doing the following:
1. Observe the green LED. A constant green light indicates the
smoke alarm is receiving 120V AC power.
2. Firmly depress the Push-to-Test button for at least five (5)
seconds. The smoke alarm will sound a loud beep about four
(4) times a second. The alarm will sound 2 short reduced-
volume beeps, then 1 short loud beep followed by a pause,
then the pattern repeats. The alarm may sound for up to 10
seconds after releasing the Push-to-Test button.
NOTE: If smoke alarms are interconnected, all smoke alarms
should sound an alarm within three seconds after any test
button is pushed and the tested smoke alarm sounds.
3. If smoke alarm does not sound, turn off power at main fuse
box or circuit breaker and check wiring. Retest smoke alarm.
REPLACE OR RETURN THE ALARM IF THE PUSH-TO-TEST
FUNCTION DOES NOT OPERATE PROPERLY AFTER FOL-
LOWING THE PROCEDURES OUTLINED ABOVE (see
REPAIRS on page 7).
DANGER: If alarm horn sounds, and smoke alarm
is not being tested, the smoke alarm is
sensing smoke. THE SOUND OF THE
ALARM HORN REQUIRES YOUR
IMMEDIATE ATTENTION AND ACTION.
MAINTENANCE AND CLEANING
In addition to weekly testing, this smoke alarm requires yearly bat-
tery replacement and periodic cleaning to remove dust, dirt, and
debris.
DANGER: ELECTRICAL SHOCK HAZARD. Turn off
power at main service panel by removing
fuse or switching appropriate circuit
breaker to OFF position before replacing
battery or cleaning smoke alarm.
BATTERY REPLACEMENT
Always turn off power to smoke alarm before replacing battery.
Replace battery at least once a year, or immediately when the
low battery signal sounds (a chirp once per minute indicates low
battery). The red LED will blink 4 times per minute after each low
battery chirp. Batteries should be replaced every year even when
the smoke alarm is receiving AC power.
Use only the following batteries as replacements in this smoke
alarm:
Eveready 522 or 1222, Duracell MN 1604, or Ultralife U9VL-J
WARNING: DO NOT USE ANY OTHER TYPE OF
BATTERY EXCEPT AS SPECIFIED IN THIS
MANUAL. DO NOT USE RECHARGEABLE
BATTERIES.
1. Turn off power to smoke alarm at main service panel.
2. Turn smoke alarm counter-clockwise to detach from mounting plate.
3. Gently pull down smoke alarm. Be careful not to separate
wire connections.
4. Pull out power plug from back of smoke alarm.
5. From back of smoke alarm, lift tab to open battery pocket door.
6. Remove battery from pocket. Disconnect and discard drained-
battery from battery connector.
!
!
!
110-762F English 12/12/06 4:06 PM Page 6
![](asset-7.png)
7
7. Connect a fresh, 9-volt battery to connector. The battery will fit
only one way. Be sure battery connector is securely attached
to battery terminals.
8. Place battery into battery pocket.
9.
Close battery pocket door. Push down until it snaps into place.
10. Replace connector plug. Connector will snap into place.
Gently tug connector to be sure it is attached properly.
11. Reattach smoke alarm to mounting plate by turning smoke
alarm clockwise until it snaps into plate.
12. Turn on power and test smoke alarm using Push-to-Test button.
CLEANING
Clean the smoke alarm at least once a month to remove dust,
dirt, or debris. Always turn off power to smoke alarm before cleaning.
•Using the soft brush or wand attachment to a vacuum cleaner,
vacuum all sides and cover of smoke alarm. Be sure all the
vents are free of debris.
•If necessary, turn off power and use a damp cloth to clean
smoke alarm cover.
•Do not spray smoke alarm with cleaners. Always place cleaners
on cloth first, then wipe smoke alarm with cloth.
IMPORTANT:
Do not attempt to remove the cover or clean inside the
smoke alarm. THIS WILL VOID YOUR WARRANTY.
REPAIR
CAUTION: Do not attempt to repair this smoke alarm.
Doing so will void your warranty.
If smoke alarm is not operating properly, see TROUBLESHOOTING.
If necessary, and if still under warranty, return smoke alarm to
Invensys Controls Americas. Pack it in a well-padded carton, shipping
prepaid, with a note describing the nature of the problem and proof of
the date of purchase to:
Invensys Controls Americas
Product Service Department
28C Leigh Fisher Blvd.
El Paso, TX 79906
If the smoke alarm is no longer under warranty, have a licensed
electrician replace the smoke alarm immediately with a compara-
ble Firex brand smoke alarm.
PRACTICE FIRE SAFETY
If the smoke alarm sounds its alarm horn, and you have not
pushed the test button, it is warning of a dangerous situation.
Your immediate response is necessary. To prepare for such
occurrences, develop family escape plans, discuss them with
ALL household members, and practice them regularly.
•Expose everyone to the sound of a smoke alarm and explain
what the sound means.
•Determine TWO exits from each room and an escape route to
the outside from each exit.
•Teach all household members to touch the door and use an
alternate exit if the door is hot. INSTRUCT THEM NOT TO
OPEN THE DOOR IF THE DOOR IS HOT.
•Teach household members to crawl along the floor to stay
below dangerous smoke, fumes, and gases.
•
Determine a safe meeting place for all members outside the building.
WHAT TO DO IN CASE OF A FIRE
1. Don’t panic; stay calm.
2. Leave the building as quickly as possible. Touch doors to
feel if they are hot before opening them. Use an alternate
exit if necessary. Crawl along the floor, and DO NOT stop
to collect anything.
3. Meet at a pre-arranged meeting place outside the build-
ing.
4. Call the fire department from OUTSIDE the building.
5. DO NOT GO BACK INSIDE A BURNING BUILDING. Wait for
the fire department to arrive.
These guidelines will assist you in the event of a fire. However, to
reduce the chance that fires will start, practice fire safety rules
and prevent hazardous situations.
TROUBLESHOOTING
DANGER: Always turn off power at main fuse box
or circuit breaker before taking trouble-
shooting action.
WARNING: DO NOT disconnect battery or AC
power to quiet an unwanted alarm.
This will remove your protection. Fan
the air or open a window to remove
smoke or dust.
!
!
110-762F English 12/12/06 4:06 PM Page 7
![](asset-8.png)
8
PROBLEM SOLUTION
Smoke alarm does not sound when
tested
NOTE: Push test button for at least five
(5) seconds while testing!
1. Check that AC power is turned on.
2. Turn off power. Remove smoke
alarm from mounting plate and:
a. check that connector plug is
securely attached.
b. check that battery is properly
attached to connector.
3. Clean smoke alarm.
The horn makes 2 quiet beeps and one
loud beep when tested.
The alarm is operating correctly. Model
ADC has a ramp-up test horn feature.
This allows you to release the test but-
ton before the alarm emits the loud
beeps.
LED blinks and alarm beeps
simultaneously every 60 seconds.
1. Battery is low – REPLACE IT
IMMEDIATELY!
2. Be sure the red LED is extinguished
after replacing the battery.
LED blinks and 30 seconds later
alarm beeps – repeats at 60 second
intervals.
Unit inoperable. REPLACE OR RETURN
FOR REPAIR IMMEDIATELY!
Smoke alarm sounds unwanted alarms
intermittently or when residents are
cooking, taking showers, etc.
1. Hire an electrician to move smoke
alarm to a new location. See SMOKE
ALARM PLACEMENT
2. Clean smoke alarm.
See “Cleaning” in the MAINTE-
NANCE AND CLEANING section.
Interconnected smoke alarms do not
sound when system is tested.
Press and hold TEST button for at least
three seconds after the first unit sounds.
The alarm sounds different than I’m
used to. It starts and stops.
The alarm is operating correctly. This
alarm features the internationally rec-
ognized horn signal for evacuation. The
horn pattern is 3 short beeps followed
by a 2 second pause and then repeats.
REPLACE OR RETURN THE ALARM IF THE PUSH-TO-TEST
FUNCTION DOES NOT OPERATE PROPERLY AFTER
FOLLOWING THE PROCEDURES OUTLINED ABOVE
(see REPAIRS on page 7).
To return Ultralife 10-year lithium batteries under warranty, include the
lithium battery, a note describing the nature of the difficulty, with proof
of date of purchase, postage and return postage prepaid to:
ULTRALIFE BATTERIES, INC.
c/o INVENSYS CONTROLS AMERICAS
P.O. Box 622
1350 Route 88 South
Newark, NY 14513
WARRANTY INFORMATION
5-YEAR LIMITED SMOKE ALARM WARRANTY AND
10-YEAR LIMITED ULTRALIFE U9VL-J LITHIUM BATTERY WARRANTY
(WHEN SOLD WITH INVENSYS CONTROLS AMERICAS SMOKE ALARM)
Invensys Controls Americas warrants to the original consumer purchaser each
new smoke alarm to be free from defects in material and workmanship under nor-
mal use and service for a period of five (5) years from the date of purchase. For
Invensys Controls Americas smoke alarms sold with an Ultralife U9VL-J 9-volt bat-
tery, Invensys Controls Americas warrants to the original consumer purchaser
each new Ultralife U9VL-J 9-volt battery to be free from defects in material and
workmanship under normal use and service for a period of ten (10) years from the
date of purchase. Invensys Controls Americas agrees to repair or replace, at its
option, any defective smoke alarm or Ultralife U9VL-J 9-volt battery (when sold
with Invensys Controls Americas smoke alarm) provided that it is returned with
postage prepaid and with proof of purchase date to Invensys Controls Americas.
This warranty does not cover damage resulting from accident, misuse or abuse or
lack of reasonable care of the product. This warranty is in lieu of all other express
warranties, obligations or liabilities. THE IMPLIED WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO A
PERIOD OF FIVE (5) YEARS FOR THE SMOKE ALARM AND TEN (10) YEARS FOR
THE ULTRALIFE LITHIUM U9VL-J 9-VOLT BATTERY (WHEN SOLD WITH INVENSYS
CONTROLS AMERICAS SMOKE ALARM) FROM PURCHASE DATE. Some states do
not allow limitations on how long an implied warranty lasts, so the above lim-
itations may not apply to you. IN NO CASE SHALL INVENSYS CONTROLS
AMERICAS BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES
FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHAT-
SOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY ITS NEGLIGENCE OR
FAULT. Some states do not allow the exclusion or limitation of incidental or conse-
quential damages, so the above limitation or exclusion may not apply to you. This
warranty gives you specific legal rights, and you may also have other legal rights
which vary from state to state.
This smoke alarm’s manufacture and distribution are licensed by the U.S. Nuclear
Regulatory Commission.
This product meets all the requirements of U.L. Standard 217.
191 E. North Avenue
Carol Stream, Illinois 60188 USA
www.invensyscontrols.com
©2006 Invensys Controls 110-762F
110-762F English 12/12/06 4:06 PM Page 8