King of Fans P2542R 54 inch Soar User Manual

King of Fans, Inc. 54 inch Soar

User manual

Download: King of Fans P2542R 54 inch Soar User Manual
Mirror Download [FCC.gov]King of Fans P2542R 54 inch Soar User Manual
Document ID3477366
Application IDkX7LdbqGAIg2GHyitLDNEA==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize162.39kB (2029924 bits)
Date Submitted2017-07-22 00:00:00
Date Available2017-07-23 00:00:00
Creation Date2017-06-01 09:30:57
Producing SoftwareAdobe PDF Library 15.0
Document Lastmod2017-06-01 09:31:03
Document TitleUser manual
Document CreatorAdobe InDesign CC 2015 (Macintosh)

®
P2542
Limited Lifetime Warranty
Progress Lighting fan motors are warranted to the original purchaser to be free of
electrical and/or mechanical defects for so long as the original purchaser owns the fan.
Pull chain switches, reverse switches, capacitors and metal finishes are warranted for a
period of 1 year. Warping of wooden or plastic blades is not covered by this warranty.
With proof of purchase, the purchaser may return the defective fan to the place of
purchase during the first 30 days for replacement. After 30 days, the purchaser MUST
contact Progress Lighting for repair or replacement which shall be determined in
Progress Lighting’s sole discretion and shall be purchaser’s sole and exclusive remedy.
Labor and Shipping Excluded. This warranty does not cover any costs or fees associated
with the labor (including, but not limited to, electrician’s fees) required to install,
remove, or replace a fan or any fan parts.
ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR A CLAIM OF
ANY KIND WITH RESPECT TO THIS PRODUCT SHALL BE THE REMEDIES SET
FORTH HEREIN. PROGRESS LIGHTING IS NOT RESPONSIBLE FOR DAMAGES
(INCLUDING INDIRECT, SPECIAL, INCIDENTIAL OR CONSEQUENTIAL),
DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF
WARRANTY, BREACH OF CONTRACT, OR OTHERWISE. THIS WARRANTY IS
GIVEN IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESSED OR
IMPLIED, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR
ANY PARTICULAR PURPOSE OR AGAINST INFRINGEMENT, AND IS VOIDED
IN CASES OF ABUSE, MISUSE OR IMPROPER HANDLING, NEGLIGENCE,
SHIPPING DAMAGE, UNAUTHORIZED REPAIRS (MADE OR ATTEMPTED) OR
UNUSUAL APPLICATION.
Some states do not allow limitations on how long an implied warranty lasts or the
exclusion or limitations of incidental or consequential damages, so the above limitations
and exclusions may not apply to you. This warranty gives you specific rights and you
may have other rights which vary from state to state.
Date Purchased
Store Purchased
UL Model No. P2542
Serial No.
Vendor No.
UPC
111017
785247 211845
785247 211852
785247 211869
Safety Rules
Unpacking Your Fan
Installing Your Fan
Making the Electrical Connections
Operating Your Fan
Care of Your Fan
10
Troubleshooting
10
Specifications
11
Table of Contents
READ AND SAVE THESE INSTRUCTIONS
1. To reduce the risk of electric shock, insure electricity
2.
3.
4.
5.
6.
has been turned off at the circuit breaker or fuse box
before beginning.
All wiring must be in accordance with the National
Electrical Code ANSI/NFPA 70-1999 and local electrical codes.
Electrical installation should be performed by a
qualified licensed electrician.
CAUTION: To reduce the risk of personal injury, use only
the screws provided with the electrical box.
The outlet box and support structure must be securely
mounted and capable of reliably supporting 35 lbs. (15.9
kg). Use only UL Listed outlet boxes marked “Acceptable
for Fan Support of 35 lbs. (15.9 kg) or less.”
CAUTION: The fan must be mounted with a minimum of
7 feet clearance from the trailing edge of the blades to
the foor.
Do not operate reversing switch while fan blades are in
motion. Fan must be turned off and blades stopped before
reversing blade direction.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, MOUNT TO OUTLET BOX MARKED “ACCEPTABLE FOR FAN
SUPPORT OF 35LBS. (15.9 KG) OR LESS”, AND USE SCREWS PROVIDED WITH THE OUTLET BOX.
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE
BLADE BRACKETS (ALSO REFERRED TO AS (“FLANGES”) DURING
ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN
THE PATH OF THE BLADES.
1. Safety Rules
7. Avoid placing objects in path of the blades.
8. To avoid personal injury or damage to the fan and other
items, be cautious when working around or
cleaning the fan.
9. Do not use water or detergents when cleaning the fan or fan
blades. A dry dust cloth or lightly dampened cloth will be
suitable for most cleaning.
10. After making electrical connections, spliced conductors
should be turned upward and pushed carefully up into
electrical box. The wires should be spread apart with the
grounded conductor and the equipment-grounding
conductor on one side of the electrical box and ungrounded
conductor on the other side of the electrical box.
11. Electrical diagrams are for reference only. Light kits that
are not packed with the fan must be UL Listed and marked
suitable for use with the model fan you are installing.
Switches must be UL General Use Switches. Refer to the
instructions packaged with the light kits and switches for
proper assembly.
12. All set screws must be checked and retightened where
necessary before installation.
13. WARNING: To reduce the risk of fire or electric shock,
this fan should only be used with fan speed control part no.
UC7067RY, manufactured by Rhine Electronic Co., Ltd.
14. Suitable for use with solid-state speed controls.
TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED
WITH AN ISOLATION CONTROL/SWITCH.
1
10
OK
Unpack your fan and check the contents. You should have the following items:
1. Mounting Bracket (inside canopy)
2. 6” Ball/Downrod Assembly (hanger pin
and locking pin pre-attached)
3. Canopy with Bottom Cover (attached)
4. Decorative Motor Collar Cover
5. Fan Motor Assembly
6. Blades (4)
7. Light Kit Pan
8. Light Kit Fitter Assembly
9. Shatter-resistant Shade
10. Transmitter and Receiver
a.
b.
c.
Blade attachment hardware
(13 Screws)
Electrical hardware and Balancing kit
(3 plastic wire connectors, blade
balancing kit)
Extra mounting screws #10-32 for outlet box
(1 Screws)
2. Unpacking Your Fan
Tools Required
Figures 1, 2, and 3 are examples of different
ways to mount the electrical box.
Phillips screw driver or straight slotted screw
driver, adjustable wrench, step ladder, and
wire cutters.
Figure 3
Mounting Options
If there isn’t an existing electrical box, then
read the following instructions. Disconnect
the power by removing fuses or turning off
circuit breakers.
Secure the electrical box directly to the building
structure. Use appropriate fasteners and
building materials. The electrical box and
its support must be able to fully support the
moving weight of the fan (at least 35 lbs.).
Do not use plastic electrical boxes.
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT
TO OUTLET BOX MARKED “ACCEPTABLE
FOR FAN SUPPORT OF 35LBS. (15.9 KG) OR
LESS”, AND USE SCREWS PROVIDED WITH
THE OUTLET BOX. ELECTRICAL BOXES
COMMONLY USED FOR THE SUPPORT OF
LIGHTING FIXTURES MAY NOT BE ACCEPTABLE FOR FAN SUPPORT AND MAY NEED TO
BE REPLACED. CONSULT A QUALIFIED ELECTRICIAN IF IN DOUBT.
3. Installing Your Fan
Figure 1
Note: You may need a longer downrod to
maintain proper blade clearance when installing
on a steep, sloped ceiling. The maximum
angle allowable is 30˚. If the canopy touches
downrod, remove the decorative canopy
bottom cover and turn the canopy 180˚ before
attaching the canopy to the mounting plate.
Figure 4
Figure 2
To hang your fan where there is an existing
fixture but no ceiling joist, you may need an
installation hanger bar as shown in Figure 4.
Hanging the Fan
Turn Canopy bottom cover to Remove
REMEMBER to turn off the power. Follow
Canopy
the steps below to hang your fan properly.
NOTE: This fan is recommended for
standard ceiling mount using the downrod
provided with this fan. When using standard
ceiling installation with the 6 inch downrod
provided, the distance from the ceiling
to the bottom of the fan blades will be
approximately 13 inches.
Figure 5
FAILURE TO PROPERLY INSTALL SET SCREWS
AS NOTED IN STEP 7 COULD RESULT IN FAN
LOOSENING AND POSSIBLY FALLING.
1. Remove the canopy bottom cover from
the canopy by turning the canopy bottom
cover counter-clockwise until it unlocks.
(Figure 5)
3. Remove the hanger pin and locking pin
from downrod assembly.
4. Route the wires exiting the top of the fan
motor through the decorative motor collar
cover then the center of the canopy bottom
cover. Make sure the slot opening are on
top. Route the wires through the canopy and
then through the ball/downrod assembly.
(Figure 7)
8. Make sure the grommet is properly installed
in the collar cover, then slide the collar cover
on the downrod until it rests on the motor
housing. Be sure that the canopy and the
collar cover are both oriented correctly.
9. Proceed to “Installing the Fan” section.
Canopy bottom cover
Standard Ceiling Mounting
2. Remove the non-slotted screw and loosen
but do not remove the slotted screw. This
will enable you to remove the mounting
bracket from the canopy. (Figure 6)
7. Re-tighten the set screws on the collar on
top of the motor housing.
Ball/Downrod
assembly
Loosen but
do not remove
Motor wires
Pin in
locked
position
Canopy
Remove
Figure 6
5. Loosen, but do not remove, the set screws on
the collar on the top of the motor housing.
6. Align the holes at the bottom of the downrod
with the holes in the collar on top of the
motor housing. (Figure 7) Carefully insert
the hanger pin through the holes in the
collar and downrod. Be careful not to jam
the hanger pin against the wiring inside the
downrod. Insert the locking pin through the
hole near the end of the bolt until it snaps
into its locked position, as noted in the circle
inset of Figure 7.
Canopy
bottom cover
Motor collar
cover
Hanger pin
Motor
collar
Reverse
switch
Tighten screws
Locking
pin
Figure 7
4.
Installing Fan to
the Electrical Box
WHEN MOUNTING THE FAN ON A SLOPED
CEILING, THE STANDARD BALL/DOWNROD
MOUNTING METHOD MUST BE USED. THE
MOUNTING PLATE MUST BE MOUNTED SO
THAT THE SLOT OPENINGS ARE ON THE
LOWER SIDE BY SLIDING THE MOUNTING
PLATE FROM THE TOP DOWN.
1. Pass the 120-volt supply wires through the
center hole in the ceiling mounting plate as
shown in Figure 8.
UL Listed
Electrical
Box
Ceiling
Mounting
Bracket
Hook
120V Wires
Washers
Mounting
screws
(supplied w
electrical box)
Figure 8
2. Install the ceiling mounting bracket on the
electrical box by using the mounting screws
provided with the electrical box. Note that
the flat side of the mounting plate is toward
the electrical box. (Figure 8)
3. Tighten the two screws on the electrical box
securely.
4. Carefully lift the fan assembly up to the
ceiling mounting plate. Make sure the tab
on the mounting plate is properly seated in
the groove in the hanger ball. (Figure 9)
WHEN USING THE STANDARD BALL/DOWNROD
MOUNTING, THE TAB IN THE RING AT THE
BOTTOM OF THE MOUNTING BRACKET MUST
REST IN THE GROOVE OF THE HANGER BALL.
FAILURE TO PROPERLY SEAT THE TAB IN THE
GROOVE COULD CAUSE DAMAGE TO WIRING.
5.
Figure 9
Follow the steps below to connect the fan to
your household wiring. Use the wire
connecting nuts supplied with your fan and
supplied with remote control. Secure the
connectors with electrical tape. Make sure
there are no loose strands or
connections. (Figure 10)
1. Connect the ground conductor of the 120v
supply (this may be a bare wire or a wire
with green colored insulation) to the green
ground lead(s) of the fan (Figure 10).
2. Connect the fan motor white wire to the
receiver white wire using a wire nut (Figure
10).
3. Connect the fan motor black wire to the
receiver black wire using a wire nut (Figure
10).
4. Connect the fan motor blue wire to the
receiver blue wire using a wire nut (Figure
10).
WHITE
BLACK
SUPPLY CIRCUIT
Remote
Receiver
Grounding
Conductor
WHITE
GREEN
REMEMBER to disconnect the power. If
you feel you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
5. Connect the receiver black wire to the
supply black (hot) wire using a wire nut
(Figure 10).
6. Connect the receiver white wire to the
supply white (neutral) wire using a wire nut
(Figure 10).
7. After connecting the wires, spread them
apart so that the green and white wires are
one side of the electrical box and the black
wire is on the other side.
8. Turn the wire connecting nuts upward and
carefully push the wiring into the electrical
box.
BLUE
BLACK
Making the Electrical
Connections
Green
Grounding
Lead
USE THE PLASTIC WIRE CONNECTORS
SUPPLIED WITH YOUR FAN. SECURE THE
CONNECTORS WITH ELECTRICAL TAPE AND
ENSURE THERE ARE NO LOOSE STRANDS OR
CONNECTIONS.
EACH WIRE NUT (WIRE CONNECTOR) SUPPLIED
WITH THIS FAN IS DESIGNED TO ACCEPT UP TO
ONE 12 GAUGE HOUSE WIRE AND TWO WIRES
FROM THIS FAN. IF YOU HAVE LARGER THAN
12 GAUGE HOUSE WIRING OR MORE THAN
ONE HOUSE WIRE TO CONNECT TO THE FAN
WIRING, CONSULT AN ELECTRICIAN FOR THE
PROPER SIZE WIRE NUTS TO USE.
BLUE
BLACK
WHITE
WHITE
Figure 10
6.
Finishing the Fan
Installation
STANDARD CEILING MOUNTING
WHEN USING THE STANDARD BALL/DOWNROD
MOUNTING, THE TAB IN THE RING AT THE
BOTTOM OF THE MOUNTING PLATE MUST
REST IN THE GROOVE OF THE HANGER BALL.
FAILURE TO PROPERLY SEAT THE TAB IN THE
GROOVE COULD CAUSE DAMAGE TO WIRING.
1. Align the locking slots of the ceiling canopy
with the screw in the mounting bracket. Push
up to engage the slots and turn clockwise
to lock in place. Immediately tighten the
mounting screw firmly.
2. Install the remaining mounting screw into
the canopy and tighten firmly.
3. Install the canopy bottom cover by aligning
the slots in canopy bottom cover with the
screws in the canopy. Rotate the canopy
bottom cover clockwise to lock in place.
4. You may now proceed to attaching the
fan blades.
Connecting the Safety
Cable
1. Turn the wood screw (not provided) into the
ceiling.
2. Place the looped end of the safety cable onto
7.
the wood screw and then tighten the screw firmly,
or connect the safety cable directly to the outer joist.
Attaching the Fan
Blades
1. Align the three screw holes in the blade
with the screw holes in the blade arm
and secure with the screws provided.
(Figure 12)
3. Make sure that canopy is tightened securely
to ceiling mounting bracket and that the
ceiling mounting bracket is tightened
securely to the electrical box.
4. Interchanging two adjacent blades can
redistribute the weight and possibly result
in the smoother operation.
5. Use the enclosed Blade Balancing Kit if the
blade wobble is still noticeable.
2. Repeat for the remaining blades.
Blade Balancing
All blades are grouped by weight. Because
natural woods vary in density, the fan may
wobble even though the blades are weight
matched.
Figure 11
Screws
The following procedure should correct most
fan wobble. Check after each step.
1. Check that all blade screws are secure.
2. Most fan wobble problems are caused
when blade levels are unequal. Check this
level by selecting a point on the ceiling
above the tip of one of the blades. Measure
from a point on the center of each blade
to the point on the ceiling. Measure this
distance as shown in Figure 13. Rotate
the fan until the next blade is positioned
for measurement. Repeat for each blade.
Measurements deviation should be within
1/8”. Run the fan for 10 minutes.
Blade
Blade arm
Flywheel
Figure 12
Touching
Ceiling
Figure 13
Installing the Light Kit
Pan/Light Kit Fitter
Assembly/ ShatterResistant Bowl
CAUTION - To reduce the risk of electrical
shock, disconnect the electrical supply circuit
to the fan before installing the light kit.
1. Loosen but do not remove two of three
mounting screws from the fan motor
assembly; Remove one mounting screw.
(Figure 14)
2. Push the light kit pan up to the fan motor
assembly so that the two loosened screw
heads fit into the keyhole slots. Turn the
light kit pan clockwise, tighten the screws.
Re-install the screw that was removed in
step 1 and tighten frmly. (Figure 14)
3. Remove one screw from the light kit pan
and loosen, but do not remove the other
two screws. Connect the wires from the
light kit fitter assembly to the wires from
the fan motor assembly by connecting the
molded adaptor plugs together. Carefully
tuck all wires and splices into the switch
cap. (Figure 15)
4. Push the light kit fitter assembly up so
that the two loosened screw heads fit into
the keyhole slots. Turn the light kit fitter
assembly clockwise, tighten the screws. Reinstall the screw that was removed in step 3
and tighten frmly. (Figure 15)
5. Place the shatter-resistant bowl into the
light kit pan, aligning the three flat areas
on the top of the shatter-resistant bowl with
the three raised dimples in the light kit pan.
Turn the shatter-resistant bowl clockwise
until it stops. (Figure 16)
Light Kit
Pan
Light kit
fitter assembly
PERIODICALLY CHECK THE SHATTER-RESISTANT
BOWL IS SEATED FULLY CLOCKWISE IN THE LIGHT
KIT PAN
Figure 15
Raised
Dimples
Light Kit
Pan
Screw
Light Kit Pan
Flat Area
Mounting
screw (3)
Figure 16
Figure 14
8.
Speed settings for warm or cool weather depend
on factors such as room size, ceiling height,
number of fans, and so on.
The fan shipped from the factory with the
reversing switch positioned to circulate air
downward. If airflow is desired in the opposite
direction, turn your fan off and wait for the
blades to stop turning, then slide the reversing
switch (located at the top of the motor housing,
refer to figure 7 on page 4) to opposite position,
and turn fan on again. The fan blades will turn
in the opposite direction and reverse airflow.
Warm weather - (Forward) A downward air
flow creates a cooling effect as shown in Figure
17. This allows you to set your air conditioner
on a higher setting without affecting your
comfort.
Figure 17
Cool weather - (Reverse) An upward air flow
moves warm air off the ceiling are as shown in
Figure 18. This allows you to set your heating
unit on a lower setting without affecting your
comfort.
Figure 18
9. Operating Your Fan
Care of Your Fan
Troubleshooting
1. Because of the fan’s natural movement,
some connections may become loose.
Check the support connections, brackets,
and blade attachments twice a year. Make
sure they are secure. (It is not necessary to
remove fan from ceiling.)
Fan will not start
Here are some suggestions to help you
maintain your fan.
2. Clean your fan periodically to help maintain
its new appearance over the years. Do not
use water when cleaning, this could damage
the motor, or the wood or possibly cause
an electrical shock. Use only a soft brush
or lint-free cloth to avoid scratching the
finish. The plating is sealed with a lacquer
to minimize discoloration or tarnishing.
Warning - Make sure the power is off
before cleaning your fan.
3. You can apply a light coat of furniture polish
to the wood for additional protection and
enhanced beauty. Cover small scratches
with a light application of shoe polish.
4. There is no need to oil your fan.
The motor has permanently lubricated
sealed ball bearings.
Problem
Solution
1.
2.
3.
Fan sounds noisy
1.
2.
3.
4.
5.
6.
7.
Check main and branch circuit fuses or breakers
Check line wire connections to the fan and switch wire connections in
the switch housing. CAUTION: Make sure main power is off.
Check batteries in the transmitter. Does the red LED light come on?
Are you standing close enough to the fan? (Normal range is 10-20
feet.) Are the dip switch settings the same on the transmitter (hand unit)
and receiver? REMEMBER TO TURN OFF POWER SUPPLY
BEFORE CHECKING THE DIP SWITCH SETTINGS IN
RECEIVER.
Make sure all motor housing screws are snug.
Make sure the screws that attach the fan blade bracket to the motor hub
are tight.
Make sure wire nut connections are not rattling against each other or
the interior wall of the switch housing.
CAUTION: Make sure power is off.
Allow a 24-hour “breaking in” period. Most noises associated with a
new fan disappear during this time.
If using the Ceiling Fan light kit, make sure the screws securing the
glassware are tight. Check that the light bulb is also secure.
Make sure the canopy is a short distance from the ceiling.
It should not touch the ceiling.
Make sure your electrical box is secure and rubber isolator pads were
used between the mounting bracket and electrical box.
MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX
BEFORE YOU ATTEMPT TO MAKE ANY REPAIRS. REFER TO THE SECTION,
“MAKING ELECTRICAL CONNECTIONS.”
10. Care of Your Fan and Troubleshooting
FAN
SIZE
54”
SPEED
Low
Med
High
VOLTS
120
FAN POWER
CONSUMPTION
AIRFLOW
(WITHOUT LIGHTS)
CFM
WATTS
11
25
65
1763
2881
4814
AIRFLOW
EFFICIENCY
(HIGHER IS BETTER)
CFM/WATT
160
115
74
NET
WEIGHT
19.40
Lbs
GROSS CUBE
WEIGHT FEET
22.27
Lbs
2.1
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
11. Specifications
©2017 Progress Lighting, Inc.
701 Millennium Blvd.,
Greenville, SC 29607
All Rights Reserved

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Warning                         : Invalid secondary xref table
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c111 79.158366, 2015/09/25-01:12:00
Instance ID                     : uuid:448f625b-361e-7b4a-8a14-1c5666d942c7
Original Document ID            : adobe:docid:indd:4aae1e07-2120-11df-bc67-b36654df4ee8
Document ID                     : xmp.id:fc1b6885-1bb7-4a1d-bb91-9b16fe68487c
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:d60fbaab-1b0c-48c8-95b3-edba33fb1e02
Derived From Document ID        : xmp.did:8ef1493f-cabe-434c-ba2a-fcc3b57569fc
Derived From Original Document ID: adobe:docid:indd:4aae1e07-2120-11df-bc67-b36654df4ee8
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2015 (Macintosh)
History Changed                 : /
History When                    : 2017:06:01 09:30:57-04:00
Create Date                     : 2017:06:01 09:30:57-04:00
Modify Date                     : 2017:06:01 09:31:03-04:00
Metadata Date                   : 2017:06:01 09:31:03-04:00
Creator Tool                    : Adobe InDesign CC 2015 (Macintosh)
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 14
Creator                         : Adobe InDesign CC 2015 (Macintosh)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: RGB-P2542R

Navigation menu