Kirisun Communication PT650003 FM Handheld Transceiver User Manual

Kirisun Communications Co., Ltd FM Handheld Transceiver Users Manual

Users Manual

FM HANDHELD TRANSCEIVERINSTRUCTION MANUALPT6500
26We are very grateful for your purchasing brand two-way radios produced by Kirisun Electronics (Shenzhen) Co., Ltd. two-way radio always incorporates the latest tech-nology, The quality and function of the two-way radio can meet your demands for reliable communication.INSTRUCTION MANUALFM HANDHELD TRANSCEIVER PT6500 Notice to the User: Please read this instruction manual before operating this radio. It's prohibited to use the radio or charge it at any area with a potentially explosive atmosphere (where the air contains gas, dust and smog, etc.), such as while taking on fuel, or while parking at a gasoline service station; or any area where radio communication is prohibited (such as a hospital or a airport.) It's prohibited to operate the radio without permission at NOTE
the areas where the government laws prohibit radio communication. Please don't expose the radio to direct sunlight for a long time; don't place the radio near any heating devices, either. Please don't put the radio in extremely dusty, moist or dabbling places; don't place it on any unstable surfaces, either. If you want to develop or remodify the radio, refer service to the well-trained professional technicians only and do not disassemble or assemble the radio.
FCC Notice Your KIRISUN radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for “Occupational Use Only”. In addition, your KIRISUN radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields– RF and Microwave. The following accessories are authorized for use with this product. Use of accessories other than those (listed in the instruction) specified may result in RF exposure levels exceeding the FCC requirements for wireless RF exposure. To ensure that your expose to RF electromagnetic energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied
with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio. DO NOT transmits for more than 50% of total radio use time (“50%duty cycle”). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the “TX indicator” lights red. You can cause the radio to transmit by pressing the “PTT” switch. ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the KIRISUN belt-clip which is listed in instructions when attaching the radio to your belt, etc., to ensure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound quality, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side. The information listed above provides the user with the information needed to make him or her aware of RF exposure, and what to do to as-sure that this radio operates with the FCC RF exposure limits of this radio. Electromagnetic Interference/Compatibility During transmissions, your KIRISUN radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites. Occupational/Controlled Use The radio transmitter is used in situations in which persons are exposed as consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver SAVE THIS INSTRUCTION MANUAL- This instruction manual contains important operating instructions for the Two-Way Radio EXPLICIT DEFINITIONS OPERATING NOTES When transmitting with a portable radio, hold the radio in a vertical position with its microphone 5 to 10 cm (2 to 4 inches) away from your mouth. Keep the antenna at least 2.5 cm (1 inch) from your head and body. If you wear a portable two-way radio on your body, ensure that the antenna is at least 2.5 centimeters (1 inch) from your body when transmitting. PRECAUTIONS WARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 inches) away from the lips and the transceiver is vertical.
WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. CAUTION! NEVER short the terminals of the battery pack. NEVER connect the transceiver to a power source other than the Battery listed below Such a connection will ruin the transceiver. DO NOT push the PTT when not actually desiring to transmit. AVOID using or placing the transceiver in direct sunlight or in areas with temperatures below –30°C (–22°F) or above +60°C (+140°F). DO NOT modify the transceiver for any reason. MAKE SURE the flexible antenna and battery pack are securely attached to the transceiver, and that the antenna and battery pack are dry before attachment. Exposing the inside of the transceiver to water will result in serious damage to the transceiver. FCC CAUTION: Changes or modifications to this device, not expressly approved by KIRISUN, could void your authority to operate this transceiver under FCC regulations.
CONTENTS Unpacking And Checking.............................................................1 Supplied Accessories .............................................................1 Preparation...................................................................................2 Charging the battery..................................................................2 Installing/Removing the battery pack.........................................3 Installing the antenna.................................................................4 Installing the optional speaker/microphone...............................4 Installing the belt clip.................................................................4 Radio Overview............................................................................5 Basic Operation............................................................................7 Programmable Button Functions................................................16 VOX............................................................................................24 Whole Setting.............................................................................24 Time-out Timer TOT ...........................................................24 Battery Power Saving..............................................................25 CTCSS/ DCS...........................................................................25 User's Resolution......................................................................26 Busy Channel Lockout BCL ................................................26 Receiving Squelch Mode.........................................................26 DTMF signaling .......................................................................26 2TONE signaling .....................................................................27 5TONE signaling .....................................................................27 Transmit beginning/ending signaling (PTT ID) ........................28 Problems And Troubleshooting ................................................28 Major Specifications...................................................................30 Status setting..............................................................................31 ITEM QUANTITY1111111UNPACKING AND CHECKING EQUIPMENT We recommend that you identify the items listed in the following table before discarding the packing material. If any damage has occurred during shipment, Unpack the transceiver carefully.please contact the dealer immediately .SUPPLIED ACCESSORIES Hand strapBelt clipLi-Polymer battery Charger Switching Power SupplyInstruction manual AntennaAntennaBelt clipCharger Hand strapBattery Switching Power Supply1
2 3PREPARATION CHARGING THE BATTERY PACK Plug the power adapter into the proper AC wall outlet; and insert the cable of the power adapter into the adapter socket on the charger; then the charger indicator lights green.Insert the battery or the radio to be charged into the charger slot. Make sure the battery is in good contact with the charger terminals. When the red indicator lights, the charger begins to charge the battery.After charging for about 5 hours, the red indicator turns dim and the green indicator lights indicating the battery has been fully charged. Leave the battery in that sate of green indicator for 1~2 hours before you remove it from the charger to achieve the best performance of the battery. Then you can disconnect the power adapter from the AC outlet.Notes:* The battery is not fully charged in the factory. Before the initial use, please charge the new battery. * The KB-36A Ni-MH battery/KB-36C Li-Ploy battery of Kirisun is adaptable with this radio.* When you charge the battery the first time or after long time storage INSTALLING /REMOVING THE BATTERY PACK*Notes: Do not cause short-circuit or throw the battery to the fire. Do not disassemble the battery by yourself.*Installing the Battery PackMatch the 3 bulges of the battery pack with the corresponding slots at the rear bottom of the radio.Installing the Battery PackThen firmly press the battery pack downwards to lock it in place until a click is heard. Removing the Battery PackTo remove the battery pack, use your thumb to press the belt clip, one side of your index finger to press the release button and then pull the battery away from the radio. (2 months), several times of charging is needed. Make sure the battery is charged at least once every three months.* Do not charge the battery again if it is charged fully or not in the low-pressure warning mode, otherwise, it will have bad effects on its life and performance. Remove the battery from the charger after charging.* When you use the KB-36A battery, and the transceiver is in the low-power warning mode, recharge the battery before use. Do not start up by force; otherwise, it will have bad effects on its life and performance. * There is a protection circuit in KB-36C battery, so the power will be cut off at too low power.
54INSTALLING THE ANTENNAScrew the antenna into the connector at the top of the transceiver by holding the Button of the antenna and turn it clockwise until secure.INSTALLING THE OPTIONAL SPEAKER/ MICROPHONEInsert the speaker/microphone plug into the jacks of the versatile connector.INSTALLING THE BELT CLIPMatch the grooves of the belt clip with those on the rear of the battery. Then press belt clip downwards to lock it in place. Push the card by inserting your nail or tool into the groove at the upper part of the clip to remove the belt clip.123456789*0#P1P2P3P4The functions of the components are as follows:A. LED Indicator Lights red while transmitting; Lights green while receiving.B. Power/Volume Switch Knob Turn clockwise till a click is heard to switch on the radio. Turn counterclockwise till a click is heard to switch off the radio. Rotate to adjust the volume after turning on the radio.C. Channel Selector Rotate to select the channel 1-128.D. AntennaE. Top Button (programmable button) It is recommended to be set as the emergency warning Button.F. Side button 1 (programmable button)G. PTT PUSH-TO-TALK : To make a call, press and hold the PTT button, then speak into the microphone with normal voice. Release the PTT button to receive signals.H. Side button 2 (programmable button)RADIO OVERVIEW
SVCPI. Button Return and delete button in the menu.J. Button Select Button.K. Button Select Button.L. Button Enter and Confirm Button.M. Numeric keypadN. Microphone/speaker jacks For connecting microphone/speaker.P1P2P3P4Explanation for the screenDescriptionSignal intensitySVC Lone WorkCompandor Scrambler channel lockoutScanningKey lockoutKeypad Tone is enableBattery capacity PIcon67BASIC OPERATION 1.Switch OnSwitch on the radio by turning the Power/Volume switch clockwise till a click is heard, then the radio will be in the state of stand by and you will hear a beep if the dealer has set it.2.Adjust VolumePress the button preset as canceling squelch to listen to the background noise and rotate the Power/Volume switch to adjust volume. 3.Select ChannelsRotate the channel selector to select channels. You will hear voice from the speaker while receiving proper signals.As shown in the above right figure:Zone 1 is the zone of current channel (8 zones from 0 to 7).H is the transmit power of the channel, H stands for high power, M for middle power while L for low power.CHANNEL 1 is the current channel (128 channels from 1 to 128). P
985. Receive a CallRelease the PTT button to receive a call. Your dealer can set CTCSS, DCS, 5 Tone,DTMF,2 Tone signaling on your radio channels by PC software. If you select a channel that has been preset with the tone signaling, you will not hear any other calls except those from your own system.4. Make a CallTo make a call, press PTT, and speak in normal voice. Please keep your mouth 3~4 cm away from the microphone.6. Operation on menu: press button to enter the menu or confirm any contents; press button to return to the previous menu or cancel the set. When entered the menu, select the sub-menu with the channel selector , or .The menu is as follows:P4P1P2P3ON/OFFON/OFF ON/OFF ON/OFFLevel: 0~9 HMLON/OFFUtilitiesScan Back LightSquelch LevelPower LevelKey tone Scrambler Save CompandingRptr/Talkaround Speak modeZone EditCallLone WorkRadio InforFre Range MCU VersionWhisper VoxContact listStatusClone ModeWireless Clone Wire CloneCh EditRx FRQ Tx CTCSSTx FRQ Rx CTCSSMenu
11104. Press , then enter selecting Scan ;5. Select Scan On or Scan OFF with / , then press to confirm it. If can not enter that way, you have to set in PC communications; Set back light:1. As shown: in CH 1 , press , Utilities is shown.2. Press to enter select mode,3. Press / , and Back Light is shown,4. Press to select On or OFF ,5. Select On or OFF with / , press to confirm. Set the squelch level:1. As shown: in CH 1 , press , Utilities is shown.2. Press to enter select mode,3. Press / , then Squelch Level is shown,4. Press to select squelch level, e.g., Level 05. Change the squelch level with / , then press to confirm. Set power level (high/middle/low)1. As shown: in CH 1 , press , utilities is shown.2. Press to enter select mode,3. Press / , then Power Level is shown,4. Press to select, e.g., Power Low ,(this function can only be programmed after setting Valid in the channel programming):P4P2P3P4P4P2P2P3P3P2P3P4P4P4P4P2P3P2P3P4P4P4P4P2P3P2P3P4P4P4P4P2P3P2P3P4P45. Change the power level with / , then press to confirm. Set Companding1 As shown: in CH 1 , press , Utilities is shown.2. Press to enter select mode,3. Press / , and Companding is shown,4. Press to select Companding ,5. Select On or OFF by / , press to confirm. Set saving1 As shown: in CH 1 , press , Utilities is shown.2. Press to enter select mode,3. Press / , and Save is shown,4. Press to select, Save 1 4 ,5. Chang the save percentage with / , press to confirm. Set scrambler1 As shown: in CH 1 , press , Utilities is shown.2. Press to enter select mode,3. Press / , and Scrambler is shown,4. Press to select, e.g., Scrambler OFF , 5. Select On or OFF by / , press to confirm. Set key tone1 As shown: in CH 1 , press , Utilities is shown.2. Press to enter select mode,3. Press / , and Key Tone is shown,4. Press to select OFF or On , 5. Select On or OFF with / , press to confirm. Set vox: P4P2P3P2P3P4P4P4P4P2P3P2P3P4P4P4P4P2P3P2P3P4P4P4The operations are as follows:Set scanning:1. As shown: in CH 1 , press , then Utilities is shown;2. Press , to enter select mode ;3. Press / ,then is shown;P4P4P4 e.g.,Scan
12 131.As shown:in CH1 ,press , Utilities is shown.2.Press to enter select mode.3.Press / , and VOX is shown.4.Press to select OFF or ON .5.Select ON or OFF with / ,press to confirm. Set whisper1.As shown:in CH1 ,press , Utilities is shown.2.Press then Whisper is shown.3.Press / to select the level of whisper,press to confirm. Set Rptr/Talkarnd1 As shown: in CH 1 , press to enter select mode, 2. Press / , and Rptr/Talkaround is shown,3. Press to select the mode, 4. Select Repeater Mode or Talkaround mode with / ,press to confirm. Set speak on mode1 As shown: in CH 1 , press to enter select mode, 2. Press / , and Speak Mode is shown,3. Press to select the speak on mode, 4. Select with / , press to confirm. Set zone mode1 As shown: in CH 1 , press to enter select mode, 2. Press / , and Zone Edit is shown,3. Press to select the zone mode, 4. Select Zone No with / , press to confirm. (This function can only be programmed after setting Valid in the channel programming)P3Rx FRQ401.660000Ch alias CHANNEL 1 Set call list1 As shown: in CH 1 , press to enter select mode, 2. Press / , and Call is shown,3. Press to select the call list , 4. Select with / , press PTT to transmit. Set Rx FRQ1 As shown: in CH 1 , press to enter select mode, 2. Press / , and Ch Edit is shown,3. Press to select 4. Press , is shown, enter the set of Rx FRQ,5 Set the Rx FRQ value with the keypad,6. Press to delete, and press to confirm. Set Tx FRQ1 As shown: in CH 1 , press to enter select mode, 2. Press / , and Ch Edit is shown,3. Press to select4. Press , is shown, enter the set of Tx FRQ, 5 Set the Tx FRQ value with the keypad,6. Press to delete, and press to confirm. Set Rx CTCSS/DCSNote: the following setting including Rx FRQ, Tx FRQ, CTCSS/DCS can only be programmed after setting Valid in the channel programming P2P3P4Ch alias CHANNEL 1P4P1Rx CTCSS401.660000P3P4P4P1P4P4P4P4P2P2P3P3P2P3P4P4P4P2P3P4P4P2P3P4P4P2P3P4P2P3P4P4P2P3P4P2P3P4P4P2P3P4P2P3P4P2P3P4
14 151 As shown: in CH 1 , press to enter select mode, 2. Press / , and Ch Edit is shown,3. Press to select4. Press , is shown, enter the set of Rx CTCSS/DCS FRQ5 Set the Rx CTCSS/DCS value with the keypad,6. Press to delete, and press to confirm.7. Stands for the radix point, press to convert among CTCSS DCS and reverse DCS. Set Tx CTCSS/DCS1 As shown: in CH 1 , press to enter select mode, 2. Press / , and Ch Edit is shown,3. Press to select 4. Press , is shown, enter the set of Tx CTCSS/DCS FRQ, 5. Set the Tx CTCSS/DCS value with the keypad,6. Press to delete, and press to confirm.7. Stands for the radix point, press to convert among CTCSS DCS and reverse DCS. Set contact list 1 As shown: in CH 1 , press to enter select mode, 2. Press / , and Contact List is shown,3. Press to select,4. Select the address cable of the call to be made with / , 5 Check the alias or address code by turning the knob, P2P3P4P4P2P3Ch alias CHANNEL 1P2P3P4Tx CTCSSXXXXP3P4P1*Rx CTCSSOFFCh alias CHANNEL 1P2P3P3P4P4*P4P1P46. Key in the address code of the person you are calling,7. Press to transmit the current contact list. Set status:1 As shown: in CH 1 , press to enter select mode, 2. Press / , and Status is shown,3. Press to select,4.Select the needed status with / , 5. Check the alias or address code of the status by turning the knob, 6. Press to select the current status.P4P2P3P4P4P4P2P3P4P2P2P2P2P3P3P3P3P3P4P4P4P4P4P4P4P4 Set wireless clone1. As shown: in CH 1 , press to enter select mode,2. Press / , and clone mode is shown,3. Press to select wireless clone or wired clone, e.g., Wireless clone / wired clone 4. Select the wireless clone with / , e.g., Wireless clone5. Press to select the clone frequency point, as shown 438 Mhz . It can be changed with / . 6. Press to select Tx or Rx mode, e.g., Send Mode / Receive Mode7. Press to transmit in Tx Mode, as shown Transmitting 8. Press to receive in Rx Mode, as shown Receiving Note: one radio should enter the Receiving , and then the other onecan enter Transmitting . Set wired clone1. As shown: in CH 1 , press to enter select mode,2. Press / , and clone mode is shown,3. Press to select wireless clone or wired clone, e.g., Wireless clone / wired clone 4. Select the wired clone with / , e.g., Wired clone
16 17Emergency AlertBack lightRptr/TalkaroundExpress select channel 1Express select channel 2Call 1, 2, 3 or 4Channel lockAdjust display contrastMan downNotes: Programmable key can be set as short press or long press.The following functions can be programmed by the dealer: NoneSet of None ScanPress the button set as Scan to start scanning. When carrier wave scan is enabled. While in scanning, the radio checks every channel (any channel in any zone) and stops on the channel on which a signal is detected until that signal disappears. If interval between signal disappearing and continuing scanning has been preset, the radio will remain on that channel. Only when there are two channels added in the scan list and the scan function has been activated, the radio can start scanning. It can be set as: short press: scan, long press OFF.1. Press the programmable key once to start scanning (it should be effective in the channel scan list). 2. Press key once again to quit.Notes: There are 8 zones from 0 (default zone) to 7; and there can be as many as 128 channels in each zone. There are totally 16 scan lists; PROGRAMMABLE BUTTON FUNCTIONSThe dealer can program the 2 Side Buttons and 1 top Button with one of the following auxiliary functions.NoneOFF ( do not set the functions )Scanlone workingContact listPower selectorShow or hide the channel alias Busy Channel Lockout (BCL)Key lockSquelch level selectorCompandingScramblerBattery power ZoneMonitoringCancel SquelchP2P3P3P4P4P4P4 5. Press to enter the wired clone, as shown Programming . (The two radios should be connected with each other by a clone cable.) Check the radio information1. As shown: in CH 1 , press to enter select mode,2. Press / , and Radio Infor is shown,3. Press to select,4. Select Fre Range / MCU Version with / , Fre Range indicates the radio frequency range; MCU Version indicates the radio version.
18 19you can select any scan list. Every scan list can scan any channels in different zones (16 channels to the most). Lone workingPress the button set as lone working to start lone working. This mode is to ensure the safety of the user while using the transceiver separately.It can be set as: short press : lone working, long press OFF.1. Press the programmable key once to start lone working;2. Press once again to quit.Notes:The lone working is connected with the automotive checking in the programming software, and will be effective when both are set. Contact list Enter the Contact list quickly: It can be set as: short press: contact list, long press OFF.1. Press the programmable key once to enter the contact list Call2. Press again to enter the content interface of the contact list, 3. Select the options in the contact list with / 4. Press PTT to transmit5. Press to quit. Power selectRotate the channel selector to enter the power level menu quickly. There are high, middle and low levels.It can be set as: short press: power select, long press OFF.1. Press the programmable key once, Zone 0 L will be shown, CHANNEL 1 2. Press it again, Zone 0 M will be shown, CHANNEL 1BCL carry BCL carryPLP2P3P43. Press it a third time Zone 0 H will be shown. CHANNEL 1 Busy Channel Lockout (BCL)Busy Channel Lockout can prevent you from interfering other radios that using the same channel.Press the PTT button, if the channel is busy, the radio with BCL function active will make warning sound and prohibit transmitting. To stop the warning sound, please release the PTT button and the radio returns to receiving mode.It can be set as: short press : Busy Channel Lockout, long pressOFF.1. Press the programmable key once, BCL none will be shown,2. Select the character you need with / , e.g.: BCL none 3 Press to confirm. Key lockPress the key programmed as key lock for one second to lock/unlock the keys for the transceiver. It can be set as: short press: key lock, long press OFF.1. Press the programmable key once, CHANNEL will be shown,2. Press it again, CHANNEL will be shown. Squelch level SelectorEnter the Select squelch level rapidly, 0~9 levels are available with the channel selector.Call listP2P3P1
2120 Battery power checkingDisplay the battery power.It can be set as: short press: battery power checking, long pressOFF.1. Press the programmable key once: the battery power will be shown,2. Press again: close the display. MonitoringPress the programmed as monitor trigger to hold out CTCSSDCS 2Tone 5Tone and DTMF signal, and you can hear the signals can not be heard in normal operation, press the key again to return to normal operation.It can be set as: short press: monitor, long press OFF.1. Press the programmable key once to start monitoring, Moni Moment ON will be shown,2. Press again: stop monitoring, Moni Moment OFF will be shown. Cancel squelchPress the key, no matter what the signal or carrier is (including optional signal), squelch will be unmuted.It can be set as: short press: cancel squelch, long press OFF.1. Press the programmable key once to start squelch constantly,2. If you release it, the squelch will be muted. Emergency AlertIf press the top key programmed as Emergency Alert , you can give the warning ring according to the programming software, or send your identity or background music to your companion or the system.It can be set as: short press: emergency alert, long press OFF.1. Press the programmable key once to start alert, It can be set as: short press: Select squelch level, long press OFF.1. Press the programmable key once, Level 2 will be shown,2. Select squelch level with / , e.g.: Level 3 Level 4 Level 5 3. Press to confirm. CompandingEnter the Companding mode when press the key programmed as Companding , It can be set as: short press: Companding, long press OFF.1. Press the programmable key once to open the Companding mode, Zone will be shown, CHANNEL 1 2. Cancel the mode by pressing it again, Zone will be shown. CHANNEL 1 ScramblerPress the key programmed as scrambler to prevent any third party to hear you talking on the phone. It can be set as: short press: scrambler, long press OFF. 1. Press the programmable key once to open the scrambler mode, CHANNEL 1 will be shown,2. Cancel the mode by pressing it again, CHANNEL 1 will be shown. P000Zone Zone P2P3P4
22 232. Press it again to stop the alert. Back lightTurn on/OFF the back light.It can be set as: short press: back light, long press OFF.1. Press and hold on this key, the back light is on,2. Release it to recover the normal mode. Rptr/TalkaroundWhen press the key programmed as Rptr/Talkaround , the next transmission will be at the same frequency as at which it is received.It can be set as: short press: Rptr/Talkaround, long press OFF. 1. Press the key once, Rptr/Talkaround will be shown,2. Press to enter,3. Press / to select the character you need: e.g.: Repeater Mode or Talkaround Mode ,4. Press to confirm. Instantly select the channelShift to the channel you selected instantly, so that you can communicate at the channel you are used to.It can be set as: short press: instantly select channel 1, long press OFF.1. Press the key once to instantaneously select the channel, e.g. CHANNEL 152. Press again to return. Call 1, 2, 3, or 4Press the side button programmed as Call 1, 2, 3, or 4 to transmit the specified code stored in the contact list. Release Call button, and speak to the microphone to call with the PTT button still pressed.It can be set as: short press: Call 1, long press OFF.1. Press the key once to make a call (within the current channel), and will quit automatically after the call. Adjust display contrastYou can adjust the display contrast as per your need.It can be set as: short press: display contrast, long press OFF.1. Press the key once, Contrast will be shown,2. Press / to select the character you need,3. Press to confirm. It can be set as: short press: display channel frequency, channel alias and channel No., long press OFF.1. Press the key once, display the channel alias, e.g.: CHANNEL 1 ,2. Press it again, the channel frequency will be shown, e.g.: 401.665003. Press it a third time the channel alias will be shown, e.g.: CH 1It can be set as: short press: Zone, long press OFF.1. Press the key once, Zone No will be shown,2. Select zone No. with / ,3. Press to confirm.It can be set as: short press: channel lock, long press OFF.1. Press the key once to perform channel lock, then you can not choose the channel, CHANNEL 1 will be shown.Change channel display Change zone Set Channel lockP2P3P4Zone 0P2P3P4P4P2P3P4
24 252. Press it again to cancel channel lock, CHANNEL 1 will be shown. VOX VOX function enables you to use the radio without manual operations. This function can only be set by the dealer, and you have to be equipped with the specified earphones. Before using VOX, you must set VOX gain level. Such setting enables the radio to identify the voice volume. If the microphone is too sensitive, the background noise will trigger the radio to transmit. If the microphone is not sensitive enough, it cannot receive your voice when you speak. Make sure to adjust VOX gain level to proper sensitivity. Whole Setting Time-out Timer (TOT)TOT timer:Time-out timer can prevent any caller from occupying one certain channel for an extended period of the time.The radio is set with a continuously transmitting limit. If the radio is continuously transmitting longer than the time preset by the dealer, the radio will stop transmitting and warningTOT forbidden period:A period in which the radio is forbidden to transmit after its overtime activity.During the period, if the PTT key is pressed, there will be a warning tone, and transmitting is forbidden. Set man downIt can be set as: short : man down, long off.1. Press the key once, man down will be shown,2. the mode by pressing it again,press pressCancel TOT pre-warning:The pre-warning will sound before the TOT action. After the sound of the warning, the timer will take action when the transmitting time has gone beyond the limit. TOT reset:The time delay from releasing the PTT key to the resetting of the timer is limited.The countdown will go on if the time after releasing the PTT key is shorter than the reset time. Battery Power SavingThe dealer can set the type of this function by programming.If the battery power saving function is on, 10 seconds after the radio hasn't receive any signals or no operation is being acted, the radio enters battery power saving mode. When a signal is received or any operation occurs, it exits battery power saving mode automatically.The types include: 1 1, 1 2, 1 4 and OFF.The automatic battery power saving function decreases the power consumption. CTCSS/ DCSThe dealer can set CTCSS/DCS tones on radio channels, which enable you to ignore (not hear) calls from other irrelevant parties who are using the same channel.When you receive a signal that has a tone different from the one set on your radio, you will not hear the signal. Likewise, signals that you transmit will only be received by parties whose CTCSS/DCS tones are the same as yours.Note: Using a CTCSS/DCS channel doesn't mean your calls are private. If other parties' CTCSS/DCS tones are identical with yours, they can hear your calls.Zone 0
2TONE signalingThe dealer can set this function by programming.There are 4 systems of which the parameters can be set, e.g.: the duration of the first and the second tone, the duration of the long tone and audio spacing, etc. Select the audio frequency 3106.0288.0hz step size 0.1hz in encoding sequence , and whether the tones sent are long or two tones, select 2TONE system and select the correspondent 2TONE code cable in 2TONE List , then transfer it with PTT. Select the audio frequency 3106.0288.0hz step size 0.1hz in decoding sequence , and whether the tones received are long or two tones, then select the correspondent decoding cable in the user's resolution . The dealer may also set the decoding replay . 5TONE signalingThe dealer can activate or inactivate this function by programming.5-Tone has 9 encoding formats: CCIR1, CCIR2, ZVEI1, ZVEI2, SVEI3, EEA, EIA, USER DEFINED 1, and USER DEFINED 2. The last two formats are user defined. 1) 5-Tone Decoding The decoding template is 5-tone decoding. If the decoding template matches the encoding template, decoding succeeds. When receiving proper 5-tone signaling, squelch will be activated according to the RX Squelch Mode defined by the user. You can receive the call and LED flashes orange.After the radio decoding succeeds, the radio will work according to the decoding call response set by the dealer. 2) 5-Tone EncodingEncoding template consists of at least one and at most three encoding sequences, and each decoding sequence can be set with 5-Tone, and DTMF. If it is set with 5-Tone, you need to program its 26 27 USER'S RESOLUTION Busy Channel Lockout (BCL)Busy Channel Lockout can prevent you from interfering other radios that using the same channel.Press the PTT button when the channel is busy, the radio with BCL function active will make warning sound and prohibit transmitting. To stop the warning sound, please release the PTT button and the radio returns to receiving mode.The dealer may provide the following two lock mode:Carrier : it will be locked if there is any Carrier ;Carrier + CTCSS/DCS transmitting is permitted if there are matched CTCSS/DCS in the channel. Receiving Squelch ModeThe dealer may set the condition under which to turn on the speakers:1. CTCSS/DCS and audio squelch: only when the CTCSS/DCS and optional signaling are matchable.2. Audio squelch: once the optional signaling is matchable.3. CTCSS/DCS squelch: when the CTCSS/DCS is matchable.4. Carrier squelch: once there is any Carrier .5.CTCSS/DCS or audio squelch: when the CTCSS/DCS is matchable, or when optional signaling are matchable.DTMF signalingThe dealer can set this function by programming.There are 4 systems of which the parameters can be set.After set a DTMF code in the code sequence , select DTMF system in the DTMF code , then select the correspondent DTMF code cable in the user's resolution and transfer it with PTT. Set a DTMF code in the decoding sequence , add the sequence into the decoding cable in DTMF decoding , then select the correspondent decoding cable. The dealer may also set the decoding replay .
28 294567transmit.No signalThe transmitting red light is on, but no voice is heardReceiving green light is on, but no voice is heardAbnormal programmingB The CTCSS/DCS signaling of both users are not the same, set it with PC.C Beyond the efficient communication range.A Make sure the antenna is well connected.B Low sensibility, trimming computer test mode .C HF amplifier may be broken, replace it.D The squelch level is too high, which makes the squelch unable to switch on, reset it by PC.E Mixer tube Q19 may be broken, replace the tube.F Frequency Modulation IC4 may be broken, replace the IC.A Power-amplifier tube no power output, replace the tube.B Replace the microphone if it is broken.C Operational Amplifier IC14 may be broken, replace it.A Replace the speaker if it is broken.B Audio power amplifier IC9 may be broken, replace it.C Switch Tube Q48 may be broken, replace it.D Operational Amplifier IC6 may be broken, replace it.A Make sure the wires are well connected.B Abnormal output of the RS-232 serial port of the computer, check the computer .C Abnormal connection of MIC and SPK jack, check the jack.Transmit ending is used to disconnect routine repeaters and auxi--liary facilities. If the ID transmitted is matchable with that of the repea--ters, the repeaters and auxiliary facilities are disconnected.content.If the PTT ID on the channel you select has been set with 5-Tone, 5-Tone signaling will be transmitted when making a call;or transmit 5-Tone signal by pressing the Call 1/2/3/4 button,, which can be set by the dealer. Transmit beginning/ending signaling (PTT ID)The identify signal of transmit beginning/ending are used to maintain or disconnect some repeaters or phone system.Transmit beginning is used to connect routine repeaters and aux--iliary facilities. If the ID transmitted is matchable with that of the repe--aters, the repeaters and auxiliary facilities are available.No.123 Problems and troubleshootingProblemsNo displayafter switched on.Phase locked loop unlockedCannot SolutionA Battery power may be insufficient. Recharge or replace the battery pack.B The power switch may be broken, replace the switch.C CPU may be broken, replace the IC.D Regulator tube Q45 may be broken replace the IC.A Phase locked loop Crystal Oscillator X1 may be broken, replace it.B Oscillator tube may be broken, replace it.C. Phase locked loop IC2 may be broken, replace the IC.A The frequencies of both users are not the same, select the same frequency channel again.
30 31Microphone ImpedanceBattery (Standard) ModelDimensions (WxHxD)Weight2.2kModel: KB-36C,Li-poly battery DC 7.4V,1750mAhtime of use 8 hours 5 5 90 period56X120X35mm310g with battery and antenna141615---1817128 Major SpecificationsPT6500Mhz(5) 350~400(1) 136~174(3) 450~520(2) 400~470FrequencyModulationNumber of Channels Channel Spacing MFWorking VoltageWorking TemperatureAntenna Impedance16K F3E/11K F3E12825 kHz/12.5kHz/20 kHz1st MF 51.65MHz 2nd MF 450kHz7.5V cathode Grounding-25 ~ +5550Model12345678910111213Status setting (by the dealer) Model Serial No. A) Channel settingChannel No.Receiving frequencyTransmitting frequencyCTCSS/DCS decodingCTCSS/DCS encodingPower Band widthScan-ningBCL
32 33High/low Power ShiftSquelch Level AdjusterMonitoring Open/CancelSquelch Open/CancelLock KeyCompandingScramblerBattery CapacityMonitoring Open/CancelSquelch Open/CancelLock KeyCompandingScramblerBattery CapacitySide button2NoneVoice Reporting SelectorRptr/TalkaroundCall1/2/3/4Lone WorkingMan DownScanningHigh/low Power ShiftSquelch Level AdjusterMonitoring Open/CancelSquelch Open/CancelLock KeyCompandingScramblerBattery CapacityB) Optional function2 1 Time-out timer TOT 15~600 s 2 2 Squelch level 1~92 3 Battery saving Off 1 1 1 2 1 4 C) Auxiliary functions button setting:Top buttonNoneVoice reporting selectorRptr/TalkaroundCall1/2/3/4Lone WorkingEmergency AlertCancel Emergency AlertMan DownScanningSide button1NoneVoice Reporting SelectorRptr/TalkaroundCall1/2/3/4Lone WorkingMan DownScanningHigh/low Power ShiftSquelch Level Adjuster
34 35We, Kirisun Electronics(Shenzhen) Co., Ltd. 6/F, Bldg.H-2,East Industrial Zone Of Overseas Chinese Town,Shenzhen 518053, ChinaDeclare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunication Terminal Equipment Directive,1999/5/EC,and that any applicable Essential Test Suits measurement have been performed.Description of equipment: FM Handheld TransceiverModel No.: PT6500-02This compliances is based on conformity with the following harmonised standards or documents: DECLARATIONOF CONFORMITY1588WenLiang, Fu General ManagerSignatureKirisun Electronics Co., LtdShenzhen, 10 Dec 2007Place and date of issue(1). ETSI EN301 489-1 V1.6.1(2004-12)(2). ETSI EN301 489-5 V1.3.1(2002-08)(3). ETSI EN300 086-1 V1.2.1(2001-03)(4). ETSI EN300 086-2 V1.1.1(2001-03)(5). EN60950 2001+A11 2004We, Kirisun Electronics(Shenzhen) Co., Ltd. 6/F, Bldg.H-2,East Industrial Zone Of Overseas Chinese Town,Shenzhen 518053, ChinaDeclare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunication Terminal Equipment Directive,1999/5/EC,and that any applicable Essential Test Suits measurement have been performed.Description of equipment: FM Handheld TransceiverModel No.: PT6500-01This compliances is based on conformity with the following harmonised standards or documents: DECLARATIONOF CONFORMITY1313WenLiang, Fu General ManagerSignatureKirisun Electronics Co., LtdShenzhen, 10 Dec 2007Place and date of issue(1). ETSI EN301 489-1 V1.6.1(2004-12)(2). ETSI EN301 489-5 V1.3.1(2002-08)(3). ETSI EN300 086-1 V1.2.1(2001-03)(4). ETSI EN300 086-2 V1.1.1(2001-03)(5). EN60950 2001+A11 2004

Navigation menu