Kitchenaid KUDD01DPPA0 User Manual DISHWASHER Manuals And Guides L0523193

KITCHENAID Dishwasher Manual L0523193 KITCHENAID Dishwasher Owner's Manual, KITCHENAID Dishwasher installation guides

User Manual: Kitchenaid KUDD01DPPA0 KUDD01DPPA0 KITCHENAID DISHWASHER - Manuals and Guides View the owners manual for your KITCHENAID DISHWASHER #KUDD01DPPA0. Home:Kitchen Appliance Parts:Kitchenaid Parts:Kitchenaid DISHWASHER Manual

Open the PDF directly: View PDF .
Page Count: 16

Download
Open PDF In Browser	View PDF

APPLIANCES
8546448

528138/8546448

Table of Contents
Drawer

lnstaBtation instructions

Dishwasher

Safety ............................

lnstaIBation Requirements .............................
Tools and Parts ...................................
Location Requirements

3
3

.............................

Water Supply Requirements

.........................

Electrical Requirements .............................

..............................

Prepare Cabinet Opening ...........................
Ebctrical Connection ...............................

5
5

if Installing Fbxibte Trim Pieces .......................
Install Dishwasher .................................

8
8

Install Drain Hose .................................

Connect to Water Supply ..........................
Install Drawer Front Panels and Toe Panel .............

11
11

Complete Installation ..............................

DRAWERDISHWASHERSAFETY
Your safety
We have provided

many important

safety

and the safety
messages

of others

in this manual

are very

and on your appliance.

important.
Always

read and obey al! safety

messages.
This is the safety
This symbol

alert symbol

alerts you to potential

All safety messages
These words mean:

All safety
happen

messages

will tell you what

if the instructions

will follow

the safety

the potential

are not followed.

hazards

hazard

that can kill or hurt you and others.
alert symbol

and either

the word 'DANGER"

You can be killed
follow
instructions.

or seriously

injured

You can be killed
instructions.

or seriously

injured

is, tell you how to reduce

the chance

of injury,

or "WARNING."

if you

don't

immediately

and tell you what

can

INSTALLATIONREQUIREMENTS
Gather the required
tools and parts before
instalhtion,
Read and follow
the instructions
any tools listed here,

starting
provided

Tools needed:

[]

7 mm socket wrench

[]

utility knife

[]

5 mm socket wrench

[]
[]
[]

needle-nose pliers
tape measure
flat-bladed screwdriver

[]

[]
[]
[]

pencil

[]
[]

sandpaper
level

[]

wood cutting board

[]

adjustable wrench that
opens to 1-1/8" (29 mm)

with

IMPORTANT: Observe all governing codes and ordinances.
Failure to meet codes and ordinances could lead to fire or
electrical shock.
Proper installation is your responsibility:
[]

[]

Install the dishwasher as specified in these instructions.

[]

5 mm open end or box end
wrench
electric or hand drill

Contact a qualified installer to ensure that the dishwasher is
installed to meet all electrical and plumbing national and local
codes and ordinances.

[]

Have everything you need to properly install dishwasher.

#2 Phillips screwdriver

[]

1-1/2" hole saw

[]

side cutting pliers

[]

valve (sized to fit hot water
supply line) with 3/8" male
compression fitting

Protect dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by the
warranty.

[]

This dishwasher is manufactured

[]

protective floor covering

[]

Install and level dishwasher on a floor that will hold the weight,
and in an area suitable for its size and use.
Product

Parts supplied:
Located in bottom drawer:
[]

2 flexible trim pieces (for sides)

[]

1 flexible trim piece (for top)

[]

edge protection

[]

hose clamp, hose type

[]

washer

[]

2 installation brackets (top)

[]
[]

drain hose support
drain hose connector

[]

2 hose clamps, wire type

[]

24 #8 Phillips head wood screws

for indoor use only.

dimensions

22-7/16" *
(57 cm)

.__

raisedtabs for
optionaltop
attaching brackets
\

(59.5 cm)

32-3/16" 34-1/2"
(81.8 cm 87.8 cm)

[] toe panel
[]

custom toe panel mounting bracket

[]

moisture protection tape

23-7/18"

side
attaching --S
tabs

2"- 4-3/8 ....
(5 cm - 11 cm)
(52 cm)
20-15/32"

_
_

drawer open

//1_

* If custom wood panels are to be used, the product depth is specified with an
11/18'* (18 ram) door panel thickness.
** Toe panel depth: Factory supplied, 2-4-3/8" (5 - 11 cm); Custom wood, 5**
(12.7 cm) less the toe panel thickness for integrated. Minimum panel thickness
using the supplied screws is 3/8'* (9 ram).
*** Door front height: Factory supplied - 30" (76.2 cm); Custom wood - 28-1/4'*
(71.8 cm) minimum.
NOTE: Product shown with front panels for dimension purposes.

Cabinet

dimensions/requirements
For dishwasher:
moisture
protection tape

[] Not water line with 4.3-145 psi (30-1000 kPa) water pressure.
[] 120°F (48.8°C) water at dishwasher.
[] An easily accessible valve with 3/8" compression fitting must
be installed in the hot water supply line.

4 ,_

(10cm)

32-5/16 "- 34-5/8"
(82_0 cm - 88_0 cm)

Utility hole:

C-.'.'
C.'

1-1/2"(3_8crn)din.
hole, eitherside immediately

adjacent

Emectrical Shock Hazard

tocorner. \

\\\\\\\

Plug into a grounded
Do not remove

3 prong outlet.

ground

prong.

Do not use an adapter.
22-7/8"

Do not use an extension

(58.0cm)

cord.

Failure to follow these instructions
fire, or electrical shock.

can result in death,

23-5/8"* (60_0 cm)

GROUNDmNG
For a grounded,

typical
installation

moisture
protection tape
1/2" (12,7 ram) from
front of countertop

mNSTRUCTmONS

cord-connected

dishwasher:

The dishwasher must be grounded. In the event of a
malfunction or breakdown, grounding will reduce the risk of
electric shock by providing a path of least resistance for
electric current. The dishwasher is equipped with a cord
having an equipment-ground
conductor and a grounding
plug. The plug must be plugged into an appropriate outlet
that is installed and grounded in accordance with all loca!
codes and ordinances.

WARNUNG:

it is recommended that wood cabinetry surrounding the
dishwasher be sealed with an oil-based paint or moisture-proof
polyurethane to prevent possibIe damage from humidity.

Improper connection of the equipmentgrounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative if
you are in doubt whether the dishwasher is properiy
grounded. Do not modify the plug provided with the
dishwasher; if it will not fit the outlet, have a proper outlet
installed by a qualified electrician.

The utility hole must be located as shown, if the hole is not
located as shown, the hoses will prevent the dishwasher from
being pushed back all the way into the cavity. Make sure the
edges of the utility hole are smooth or covered, if the utility hole
is through a metal cabinet, the hole must be protected with the
edge protector provided.

The dishwasher must be connected to a grounded metal,
permanent wiring system, or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminat or lead on
the dishwasher.

The 3 prong grounded outlet must be installed within 6"
(15.2 cm) to 18" (45.7 cm) of the cabinet side wall.
NOTE: The power outlet must be accessibIe after installation.

*IMPORTANT: Custom wood door panels, if used, may be wider
than the dishwasher to match surrounding cabinets. The 23-5/8"
(60.0 cm) must be increased so that there is a 1/4" (6.4 mm)
clearance between the cabinet side and panel edge.
For corner installation, there must be a !/2" (12.7 mm) space
between the adjacent cabinet doors (Le. door knobs) and open
dishwasher drawer.

For a permanentBy connected

SAVE THESE

dishwasher:

mNSTRUCTmONS

A 120-volt, 60 Nz, AC-onty, 15 amp fused electrica! supply is
required. (Circuit breaker or time-delay fuse is recommended.)
is recommended that a separate circuit serving only this
appliance be provided.

Garbage
Disposer:
Ifyouplantoinstalla garbage
disposer,
anadditional
separate
120-volt,
60Hz,AC-only,
15or20ampfusedebctrical
supplyis
required.

Recommended
groundmethod
Thisappliance
mustbegrounded.
Thisappliance
isequipped
withapowersupply
cordhaving
3 prongground
plug.To
minimize
possible
shockhazard,
thecordmustbeplugged
intoa
mating
prongground-type
outlet,grounded
inaccordance
with
localcodesandordinances.

iNSTALLATiONiNSTRUCTiONS
Prepare
moisture
of the

the cabinet
protection

opening
by applying
self-adhesive
tape to the dry dustofree
underside

Option

1 : Power

Supply

Cord

Method

countertop,

countertop

taupe,

moisture
protection tape

1/2" (12.7 ram) from
front of countertop
2.

g.
4.

Tip Over Hazard

Turn off water supply.

Do not use dishwasher
opening.

Decide which attaching tabs to use to secure the dishwasher.
The four side attaching tabs are recommended.

drawer until inside cabinet

Doing so can result in serious

injury or cuts.

if the countertop material permits and the optional top
attaching brackets will be used, install them now.
Slide the brackets under the raised tabs. Using the flat side of
the side cutting pliers, lightly tap the brackets into piace.
Make sure the locking tabs on the brackets are completely
passed through the raised tabs on the dishwasher.
mounting

bracket_
\..

locking

tab

raised tab

if using the factory-installed power cable and plug, go to
"Electrical connection" section, Option: 1: Power Supply Cord
Method.
if direct wiring the dishwasher, go to "Electrical connection"
section, Option: 2: Direct Wiring Method.

Place cardboard or other protective covering on the floor in
front of cabinet opening. Piace the dishwasher on covering.

Begin to route the hoses and power supply cord through the
utility hole in the cabinet.

Push dishwasher partway into the opening.
IMPORTANT: Push against the outside edges of drawers as
shown. Do not push against the center of the drawers.

4, Asthedishwasher
isbeingpushed
intotheopening,
slowly
pulltheinlethose,drainhoses
andpowersupplycord
through
theutilityhole.
5, Remove
thestrapfromupperdrawer.
Goto"IfInstalling
Flexible
TrimPieces"
section.

6, Rotate drawer to the right onto its side and place on the
protective cover.

Option2: DirectWiringMethod
(-\

electrical cover

7, Slide the left-hand runner back into the dishwasher.
8, The electrical cover is located in the back Ieft corner.

E_ectrical
ShockHazard

Use a flat blade screwdriver to press the release button. Slide
the cover to the right and then pull up.

Disconnect
electrica_

power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or e_ectrical shock.

j,_
i

press
releasebutton
1, Place cardboard or other protective covering on the floor in
front of cabinet opening. Place the dishwasher on covering.

Remove factory-installed

2, Disconnect power.

1, Disconnect the black and white wires of the power cord from
the terminal block.

power cord,

3, Open the bottom drawer.
4, Press in the right-hand runner clip and push it back about 6"
(15.2 cm). Repeat with the left-hand runner clip.

strain relief

NOTE: When removing the drawer there is limited range of
movement due to the attached water hoses.

terminal block

runner clip

Lift the right edge of the drawer off its runner. Slide that runner
back into the dishwasher. Lift the drawer completely off the
left-hand runner.

green ground screw

2, Use a 7 mm socket wrench to remove the green ground
screw. Remove the green ground wire.
3, Use a Phillips screwdriver to remove the strain relief screw.
Open the strain relief.
4, Pull the power supply cord off the dishwasher through the
back of the dishwasher.
5, Close the strain relief and replace screw so it does not
interfere with the electrical cover.

6. Remove
thehouse
wiringknockout,
knockout

ElectricalShockHazard
Connect

7, Runthehouse
wiringthrough
theconduit
connector
(not
supplied)
andintothedishwasher
through
theknockout
opening,

Failure

ground

wire

to green

to do so can result

ground

in death

screw.

or electrical

shock.

11. Piace the ground wire under the green ground screw, Use a
7 mm socket wrench to securely tighten the green ground
screw,

12. Tighten the conduit connector, Replace electrical cover,
13. Pu[I the bottom drawer runners all the way out. Make sure the
latches on the back of each drawer runner are facing forward,

8. Secure the conduit connector in the knockout opening.

From the house wiring, strip 1/2" (13 mm) of insulation off of
each wire.
1/2" (!3 mm)
14, if the bottom drawer was rotated, rotate the drawer to unwind
the hoses and then put the drawer on the runners making
sure the hoses are looping upward.

t0, insert the black supply wire and the white neutral wire into
the appropriate wire clamp on the terminal block. Securely
tighten the clamps.
terminal block
white wire
,f

black wire

15, Make sure both runner clips have snapped into place, if they
have not, pull the runner clips forward until they do.
16, Close the bottom drawer.
/

terminal block

ground wire

17,Usethesidecuttingplierstocutthecabletiesecuring
the
hoses
andpowersupplycordtothebackofthedishwasher.
back of
dishwasher

22, As the dishwasher is being pushed into the opening, slowly
pull the inlet hose and drain hoses through the utility hole. Let
the house wiring gather behind the dishwasher.
23, Remove the strap from upper drawer.

::,

cable tie

18, Completely remove the power supply cord and save it, in
case a power cord installation is needed in the future.

If the cabinet opening is 24" wide x 34-1/2" high (61.0 cm x
87.6 cm), flexible trim pieces can be attached a!ong the top and
sides of the dishwasher. Top and side trim pieces are different
lengths.
1, Open the drawers to expose the chassis trim.
2, Center the flexible trim pieces.

top trim

side trim

Tip Over Hazard
Do not use dishwasher
opening.

piece

side trim
piece

drawer until inside cabinet
open drawer

Doing so can result in serious

injury or cuts.

......chassis trim
edge

If using the optional top attaching brackets, place the trim
pieces under the attaching brackets.

Remove trim pieces backing paper to expose the adhesive.

Place the trim pieces on the trim and press.

Finish pushing dishwasher into opening.

19, Place cardboard or other protective covering on the floor in
front of cabinet opening. Place the dishwasher on covering.
20, Begin to route the hoses through the utility hole in the cabinet.
IMPORTANT: Push against the outside edges of drawers as
shown. Do not push against the center of the drawers.

Leave protective cover on floor.
2, Open the bottom drawer.
3,

21, Push dishwasher partway into the opening.

Press in the right-hand runner clip and push it back about 6"
(15.2 cm). Repeat with the left-hand runner clip.
NOTE: When removing the drawer there is limited range of
movement due to the attached water hoses.

iBm_

4,
runner clip
4,

Lift the right edge of the drawer off its runner. Slide that runner
back into the dishwasher.

Lift the drawer completely off the left-hand runner.

Rotate the drawer to the right onto its side and place on the
protective cover.

Choose

attachment

option

Option 1: Side attachment
1. The dishwasher side attaching tabs are accessed through
holes in the sound insulation.
IMPORTANT: For best installation, use all four attaching tabs.

2. Secure the attaching tabs to the cabinet using #8 Phillips
head screws.
side

Slide the left-hand runner back into the dishwasher.

8. Reach inside the dishwasher to adjust the feet using a 5 mm
open end, box end, or socket (if space permits) wrench.
Adjust for cabinet height and level. Place a level on the drawer
runners. Level the dishwasher to within 3/32" (2.4 mm) from
front to back.
3/32" (2.4 ram) minhq'_um
clearance to underside of counter_
T

Pull the bottom drawer runners all the way out. Make sure the
latches on the back of each drawer runner are facing forward.

If the bottom drawer was rotated, rotate the drawer to unwind
the hoses and then put the drawer on the runners making
sure the hoses are looping upward.

Make sure both runner clips have snapped into place. If they
have not, pull the runner clips forward until they do.

(!
ii

Place a level across the drawer runners. Level the dishwasher
to within 3/32" (2.4 mm) from side to side.

6. Close the bottom drawer.

Option
1,

Top attachment

If the top attaching

brackets

are used, open

the top drawer

slightly:
2,

Option 2: Garbage disposaB connection
1,

Screw the top attaching
brackets
to the underside
counter with two #8 Phillips head screws.
IMPORTANT:
a maximum

The top attaching

brackets

3/4" (19 mm) vertical

gap.

of the
2,

Route the drain hoses as shown and press the hoses
into the drain hose support,
Decide if the drain hoses need to be trimmed,
trim

can accommodate
3,

....... top attaching bracket

Slip a wire clip
hose, Push the
drain hose
5 clicks,

the top drawer,

Attach

the
the

1: Sink

drain

waste

Route the drain hoses as shown
the drain hose support.

Decide if the
trim them,

Slip
hose.

a wire
Push

drain

hoses

clip over
the

hoses

drain hose connector
5 ciicks,
4,

need

and

press

the

to be trimmed,

each drain

Attach the drain hose connector
the supplied
hose clamp,

Attach

head

into

If they

do,

hose

connector

hose

wire clip ¢_

to the

The drain

garbage

drain hose
connector
disposal

clamp,

hose connector
hose length.

to the cabinet
shown
below,

must not support

Keep hoses

with

the

as fully extended

7_ wireclip

firmly,

the drain

hoses

firmly,

into the

Position
the wire clips between
the two positioning
ribs on the
drain hose connector,

a #8 Phillips

drain
supplied

weight of excess
as possible.

tee connection

connector

Attach the drain hose support
bracket
a #8 Phillips
head screw at the height
NOTE:

Option

50 wire clip

over each drain
hoses into the

Position
the wire clips between
the two positioning
ribs on the
drain hose connector,

using
3,

If they do,

them,

hose

support

screw

at the

drain hose
connector
to the

waste

tee using

bracket

to the

cabinet

height

shown

below,

with
o_
!

NOTE: The drain hose connector
must not support the weight
of excess hose length. Keep hoses as fully extended
as

possible.
water supply

.....8" (20,3 cm) rain. bend
radius from valve

Option
1,
2,

the

drain

as shown,

Slip a wire clip
hose, Push the

Position

connector

the wire

#_) wire clip

over each drain
hoses into the

clips

firmly,

between

the two positioning
ribs
drain hose connector,

If they do,

them,

drain hose
5 clicks,
4,

connection
hoses

Decide if the drain hoses need to be trimmed,
trim

3: Air break

Route

on the

wire clip U

drain hose
connector

5. Attachthedrainhoseconnector
totheairbreakusing
thesuppliedhoseclamp,
EJ_

air break
E

drain hose
connector

waste

Remove
material.

front

panels

On the shorter front panel
tape securing
the connector

Connect

the end

connector

from

of the
the

box

and discard

(lower drawer),
remove
the
and wires.
Discard tape.

medallion

lower

all shipping

connector

to the

drawer.

wire
opening
water supply

lower front
panel
8" (20.3 cm) min. bend
radius from valve
end of medallion
connector

install the flat seal washer on the end of the inlet hose.
Connect the inlet hose to the water supply valve. Tighten
securely.
2,

Gently feed the wires and connectors
wire opening.

Line up front panel tabs to slots in metal plate, Do not
puii the connector from wire opening,

Turn the water valve on and check for any leaks.

into the metal plate

slots _

va,ve0

"- front panel

f,atsea,
._.__....

3, Open top drawer. Remove the packing tape from the front
and rear of dish rack.
4, Close drawer.
5, Open bottom drawer. Remove the packing tape from the front
and rear of dish rack.

Push

the front

Repeat

When
top
top

_'_m

steps
installed

panel

ata, plat e

down

2-6 for the
properly,

of dishwasher
with
and bottom
panel

to lock in place.

top

drawer

top

panel

panel.
should

a 3/8" (9.5 ram)

be even

gap between

with
the

6, Close drawer.

Option1:Insta{Istandardtoe pane{
NOTI=S:
Depending
oncountertop
height,
youmaynothaveto
trimthetoepanel.
Rugs
placedinfrontofdishwasher
couldinterfere
with
toepanel.
Clearance
between
floorandtoepanelmay
needtoinclude
therugthickness.
1. Partially
openthebottom
drawer.
2. Turnthetoepanelupside
downandholdvertically
against
the
bottomedgeofthetubside(notthefront).
3. Onthetoepanel,
markwherethetub'sbottomedgeis.

Remove

any rough

Partially open bottom
drawer. Position
and slide onto the underside of tub.

toe panel
mounting rail

edges

by sanding

clamping
screw

smooth,
toe panel

behind

door

Close the drawer. Check that there is
1/2" (12.7 mm) minimum clearance
between the bottom edge of the toe
panel and the floor.
if not, remove the toe panel and shorten
using the utility knife. Remove any rough
edges.

ss{{_ i

(12_7 mm)

floor

10. Slide toe panel back onto mounting rails.
11. If needed, you may simply push the toe panel back or forward
on the mounting rail.
12. With a Phillips screwdriver, tighten the toe panel clamping
screws on both sides.
13. Plug in dishwasher or reconnect power.
bottom edge
of tub side

14. Go to "Complete Installation" section.

On a stable surface, place toe panel on a wooden cutting
board and pick the closest groove to the mark. If the mark is
between two grooves, choose the groove that makes the toe
panel the shortest.

At the selected groove, use a utility
knife and cut the vertical rib the
length of the toe panel until entire
piece is removed.

Snap off the toe panel tabs.

ear of

toe panel

tabtoe
panel

Option 2: Install custom front panels
Custom

front

Prepare

Mount
the
not extend

panem dimensions

the custom

is customer
9 ==

2-5/16"
(5_9cm)

Lay the custom
covering.

Measure

and

position

line

panels

to specifications

to the custom
panel.The
the back surface of the

supplied,

I"_-- (22.9 cm)

front

handle
beyond

front
mark

location
panel

is customer

face down

the vertical

on the

back

front

preference.)

on a protective

centedine

of the

shown.

screws must
panel. (Handle

and

horizontal

panels.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

medallion
cutout area

_(_
Top panel
(frontview)

23-7/16" (59.5 cm)

_ark

Top Panel -

1-7/16"
Bottom (36.5
panelram)
1-3/16" (30.2 ram)

horizontalline
mark
centerline

Feed the wires of the medallion
front of the custom
front panel
into the

prepared

medallion

Remove

the

on both

connector
and push

through
the
the medallion

hole.

2-1/8"

medallion
cutout area

pins

by pulling
the
nose pliers.

Bottom panel
(frontview)

pins

straight

sides
out

of the
with

dishwasher
a pair

drawer

of needle-

.........

23-7/18" (59.5 cm)

/
1-7/32"

1_9/32"
(32.8 mm)

7. Gently pull the bottom of the metal plate away from the
dishwasher, and then pull down.
NOTE: Do not cut
beyond outline of
medallion
Rout
a 1/4"cutout_
(6,4 ram)
radius around back side
--1-13/84"
(30_6 ram)

of medallion cutout,

2-13/32"
(60.8 ram)
Medallion cutout
(frontof panel)

Upper and lower panel minimum thickness is 5/8" (16 mm). Panel
thickness above 11/!6" (18 mm) can be accommodated but
product depth will increase accordingly.
Custom front panel materia! must be suitable for damp
conditions or adequately sealed to withstand moisture. Using a
moisture-resistant material can provide additional protection.
Taping edges alone may not provide adequate sealing. For
painted panel, paint all rear edges to improve sealing.

Lay the custom

front panel face dovvn,

Feed the medallion
the metal plate,

wires through

the wire opening

wire opening
..................
front panel

10,LaythemetaH
pilateonthebackofthecustomfront
panel
11,AHign
thecenterHine
marked
onthecustompaneH
withthe
diamondshapeandnotchinthemetaH
pilateto centerthe
metaH
pilatehodzontaHHy,
AHign
thehodzontaH
Hine
withthe
topofthemetaH
pilate,

15, Line up the bracket holies with the pin holies and repHace
each pin so that the pin Hine is vertical

horizontal line

[

top of plate

centerline

16, Repeat steps 2-15 for other custom

Option

2: _nsta{I custom

panel

toe pane_

Oustom toe pane_ dimensions
12, Using the screws provided, fasten the metal plate to the front
panel through the 3 inner holes.

2_5/32 ,,
(55 ram)

23-1/2" (59,7 cm)

5" (12J crn)
max,

(varies)

J
,Z

three

The black prefinished toe panel can also have a custom front
panel with a thickness from 3/8" to 3/4" (9-19 mm) attached to it.

innerholes

13, Connect
the
connector,

medaHHion

connector

to the dishwasher

Determine the height of the toe panel custom panel: The
minimum height is 2-3/4" (70.5 mm). Measure from the top of the
adjacent cabinet door front to the floor. Subtract 28-15/32"
(72.3 cm) for needed toe panel height.
NOTES: Depending on countertop
trim the toe panel.

Rugs placed in front of dishwasher could interfere with
toe panel. Clearance between floor and toe panel may
need to include the rug thickness.

lower front
panel

end of rnedallic
connector

height, you may not have to

Prepare the custom toe panel to specifications

Lay the custom toe panel face down.

shown above.

Fasten the biack plastic toe panel on the back of the custom
toe panel with the screws provided with the dishwasher.
I i
I I

14, Slide
the

the

metai

dishwasher

pilate tabs
and

gentiy

into
puii

the

notches

and

plastic
toe panel

shots on

up to Hock in piace,

_ustorn
toe panel

Partially open bottom drawer. Position custom toe panel
behind door and slide on the underside of tub.

5, Close the drawer and slide the toe panel back onto mounting
rails.

6. Ifneeded,
youmaysimplypushthetoepanelbackorforward
onthemounting
rail.
7. WithaPhillips
screwdriver,
tighten
thetoepanelclamping
screws
onbothsides.
toe panel
mounting rail

clamping
screw

\
\

8. Plug in dishwasher or reconnect power.

1. Check to be sure all parts are now installed. If there is an
extra part, go back through the steps to see which step was
skipped.
2. Check to be sure you have all of your tools.
3. Dispose of/recycle all packaging materials.
4. Read "Dishwasher Use" in the Drawer Dishwasher Use and
Care Guide.
If dishwasher

does not operate, check the following:

[]

Household fuse is intact and tight; or circuit breaker has not
tripped.

[]

Electrical supply is connected.

[]

See "Troubleshooting"

in your Use and Care Guide.

trademark/TM trademark of KitchenAid,
Canada Hcensee in Canada

U.S.A.,

Printed
Benton Harbor,

Michigan

49022

in U.S.A.
10/2004

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 16
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Fri Apr 20 13:13:04 2007
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Kitchenaid KUDD01DPPA0 User Manual DISHWASHER Manuals And Guides L0523193

KITCHENAID Dishwasher Manual L0523193 KITCHENAID Dishwasher Owner's Manual, KITCHENAID Dishwasher installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation