Kobian Canada HSPS3BT Bluetooth headset User Manual

Kobian Canada Inc., Bluetooth headset

User Manual

Basic function: 1. Receive a call 2. Reject a call 3. Volume adjust 4. Redial the last phone number User Manual: Pairing mode for your headset 1. Press and hold the power button (approximately 7-10 seconds) until the blue LED light is continuously on. (It will flash a few times before it's continuously on). Paring with your PlayStation 3 System 1. From the system home menu, go to “Settings” then “Accessory Settings”. 2. Select "Manage Bluetooth Devices" option to register or pair the Bluetooth headset with your PlayStation 3 system. 3. If no Bluetooth device is paired with your system, you will see the message "There are no Bluetooth device registered. Do you want to register?" on the screen. In this case, please select "Yes" and press the X button to continue with the pairing process. 4. If a Bluetooth device has been paired with your system, a list of all the Bluetooth devices will appear. You will need to select "Register New Device" and press the X button to pair a new Bluetooth device. Note : Only one Bluetooth headset can be paired to the system at a time. You must unregister the previous headset from the system first before pairing a new headset. 5. After you have selected to register a device, you will see the message "To register, you will need to prepare the Bluetooth device" on the screen. This means that the system will scan for any Bluetooth devices that is within range. Make sure the Bluetooth headset is set to pairing mode in order for the system to locate it. Please refer to the section "Pairing Mode For Your Bluetooth Headset". 6. Once you’ve prepared the Bluetooth headset to pairing mode, you can press the X button to start scanning. 7. After the scan is completed, your system will list all the devices found within range. Choose the “HIP STREET” Bluetooth headset and the press the X button to continue. (If no device is found, then it is likely you have not correctly prepared the headset to be "paired"). 8. Once you have selected the “HIP STREET” headset to be paired, you will need to enter the headset’s pass key to complete the pairing process. Please press the X button to begin entering the pass Key. The pas key is 4 zeros (0000). You can use the on-screen keyboard to enter the pass key. After you have entered the correct key, you can move the cursor onto the green Enter button and press the X button to confirm. 9. After the pass key is entered, you should see it in the center of the screen. Use the D-pad to highlight OK, and press the X button.
10. You’ll see the message “Register Completed” on the screen when completed. 11. You have successfully paired your Bluetooth headset. Press the X button to continue and exit. Setting your Bluetooth headset as an Input/ Output Device After the Bluetooth headset has been successfully registered or “paired” with your Playstation 3 system, you must set it as the default “Input / Output Audio Device” before it can be used. 1. From the home menu, go to “Settings” and then “Accessory Settings” followed by “Audio Device Settings”. 2. Select “Input Device” and press the X button. This is where you select the microphone for voice chat. Scroll up and down until you find your headset and press the X button. The “Output Device” will automatically change to match the selected “Input Device”. This setting will allow you to hear other players' voice chat messages on the Bluetooth headset. Once the input and output device has been selected, you can test the headset’s input/output levels by speaking into the headset. You should be able to hear your voice over the selected output device. If your voice is too soft or low, you can select “Microphone Level” and press the X button to adjust the volume. When you have completed adjusting the “Audio Device Settings”, select “OK” and press the X button to return to the home menu. Turn off and on your headset 1. To turn off the headset, press and hold the power button (approximately 3 – 5 seconds). The blue LED light will turn on, turn off and remain off. 2. To turn on the headset, press and hold the power button (approximately 3 – 5 seconds). When the blue light turns on, release the power button.Note : When the headset is in standby mode, the blue LED light will quickly flash once every 5– 7 seconds. Mute Function 1. Press and hold the “Vol-“ and “Vol+” simultaneously for approximately 3 seconds. You will hear a beep and the headset is in mute mode. 2. To take the headset off the mute function, press the “Vol-“ and “Vol+” simultaneously. Note: The mute function will only mute the microphone. You will still be able to listen. Using your headset with other Bluetooth enabled devices This headset can also be used with other Bluetooth enabled devices, such as cell phones. Please refer to your user manual for such devices for instructions on pairing the headset. To set the headset to the pairing mode, please refer to the section "Pairing Mode For Your Bluetooth Headset". The pass key will remain the same with 4 zeros (0000). Receiving a call 1. Once the headset is paired and connected to your cell phone, press the “Telephone Call” button to receive a call. You will not only hear your cell phone ring, but a beep through the headset. 2. Press the “Telephone Call” button once to disconnect the call. Press twice quickly to reject.
FCC Information FCC ID：：：：YH5HSPS3BT This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation. Federal Communications Commission (FCC) Statement This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. Tested to comply with FCC standard. FOR HOME OR OFFICE USE. Warning : This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. & This device and its antenna(s) must not be co-located or conjunction with any other antenna or transmitter.

Navigation menu