Kodak Easyshare 5300 Users Manual

2015-02-04

: Kodak Kodak-Easyshare-5300-Users-Manual-370235 kodak-easyshare-5300-users-manual-370235 kodak pdf

Open the PDF directly: View PDF .
Page Count: 20

Download
Open PDF In Browser	View PDF

Start Here
EasyShare 5300

All-in-One Printer

EasyShare 5300

All-in-One Printer

Print
Copy
Scan

Rotate

Zoom

Proofsheet

Transfer

Photo
Scan

Copy

Help

Black Ink Cartridge

Cancel

Start

Color Ink

Cartridge

On/Off

Attention

Note: A USB 2.0 cable is required to connect your Kodak All-in-One Printer to your Windows or Macintosh OS computer.

Identify Main Components

13.
14.

5.
6.

15.

1. Scanner glass

10.

5300

All-in-One Printer

16.
All-in-One Printer

Ea
EasyShare
5300

12.
Easyshare

11.

9. USB drive/PictBridge port

2. Printer access door

10. Memory card light

3. Output tray

11. Memory card slots

4. Paper-width guide

12. Control panel

5. Main tray

13. USB port

6. Photo tray

14. Power connector

7. Paper-length guide

15. Rear access door

8. Photo tray light

16. Scanner lid

www.kodak.com/go/aiosupport

Unpack Printer and Install Control Panel
IMPORTANT: Do not connect the USB cable to the printer until instructed during
software installation.

a) See box flaps for unpacking instructions.
Remove all orange shipping tape from the printer.

b) If not preinstalled, insert the control panel overlay,
bottom end first.
OK

E
EasyShare 5300

All-in-One Printer

c) Press down on all edges of the overlay until
it snaps into position.

EasyShare 5300

All-in-One Printer

Rotate

Proofsheet

Zoom

Transfer

Photo
Copy

Scan

Help

On/Off

Cancel

Attention

www.kodak.com/go/aiosupport

Load Paper
a) Load photo paper into the photo tray.
Lift the photo tray lid until it remains standing without
support. Insert the photo paper glossy side down.
IMPORTANT: Do not overload the photo tray.
Max 20 sheets.

b) Push the photo tray in until it clicks into place.
NOTE: You can only print to the photo tray when the
photo tray is pushed in.
Lower the photo tray lid.

c) Load plain white paper into the main tray.

www.kodak.com/go/aiosupport

Install Printhead
IMPORTANT: The printhead is fragile. Handle
carefully.
a) Lift the printer access door. Make sure the orange
tape is removed from the carriage.

b) Remove the printhead from its bag.
IMPORTANT: Insert the printhead immediately
upon opening sealed bag.

c) Pull on the orange tab to remove the protective retainer.

www.kodak.com/go/aiosupport

Install Printhead
d) Carefully remove and discard the black plastic shield
and the orange protective cap.
IMPORTANT: Do not touch the copper-colored
contacts.

e) Place the printhead into the carriage. Insert at the
angle shown.

f) Push firmly against the back wall of the printhead
until it clicks into place.
Tip: The printhead requires a firm push and makes
an audible click when locked into place.

www.kodak.com/go/aiosupport

Install Ink Cartridges
a) Remove the black ink cartridge from its bag.

Black Ink Cartridge

IMPORTANT: Insert ink cartridges immediately
upon opening sealed bag.
10

B
k

e
g

rtr

b) Carefully remove and discard the orange cap.
Handle ink cartridges carefully to avoid ink transfer.

c) Insert the black ink cartridge into the printhead.
10

Black Ink Cartridge

www.kodak.com/go/aiosupport

Install Ink Cartridges
d) Press down on the ink cartridge until you hear it
click into position.

Blac
k In
k Ca
rtri
dge

e) Open and uncap the color ink cartridge. Insert it into
the printhead.

C
o
lo
r

C
a

t
r
id

g
e

Bla
k

In
ge

rid
rt

ge
rid

rt
Ca

C
olo

k
In

ck
Bla

tr
id

10
10

f) Press down firmly on the ink cartridge until you hear
it click into position. It is normal for the printhead to
flex when inserting the cartridge. You will not damage
the printer.
Close the printer access door.

www.kodak.com/go/aiosupport

Connect Power
a) Connect the power supply and adapter.
All-in-One Printer
Easyshare

5300

b) Remove the plastic film from the LCD display.
Position the LCD display and press ON.

EasyShare 5300

All-in-One Printer

c) Press ON. If prompted, select your language.
Use the
key to select a region.

EasyShare 5300

All-in-One Printer

-ON

www.kodak.com/go/aiosupport

Calibrate Printer
IMPORTANT: Make sure that the photo tray is
pushed in. The photo tray light should be lit.
a) Press Start. Wait two minutes for the calibration sheet
to print.
Tip: If the calibration sheet does not print properly,
see the Troubleshooting section in this setup guide.

b) Remove the calibration sheet from the output tray.
Place it face down and align to the front, right corner
of the scanner glass, as shown.
IMPORTANT: The blue arrow in the corner of the
calibration sheet must point to the registration
marks as shown.
4x6

4x6

c) Lower the scanner lid and press Start. Remove the
sheet from the scanner glass when the calibration
is complete.

4x6

d) Lift the photo tray lid, then slide the photo tray toward
you to return to main tray operation. The photo tray
light will turn off.

www.kodak.com/go/aiosupport

Install Software

WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
WINDOWSWINDOWS
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH
MACINTOSHMACINTOSH

WINDOWS
IMPORTANT: Do not connect the USB cable
to the printer until instructed during software
installation.
a) Load the Kodak AiO Printer Software CD into the
CD-ROM drive. Follow the on-screen prompts
when the instructions appear.
If instructions do not appear, click Start, then Run.
Select CD-ROM drive and type setup.exe, then
press ENTER.

b) Connect the USB cable to the printer when instructed.
Continue to follow the on-screen prompts until
installation is complete.

MACINTOSH
a) Connect the USB cable to the printer and your
Macintosh computer.

b) Load the Kodak AiO Printer Software CD into the
CD-ROM drive.
The Kodak AiO Printer Software installer window
should be displayed. If not, double-click the Kodak
AiO Printer Software CD icon on the desktop. Follow
the on-screen prompts until installation is complete.

www.kodak.com/go/aiosupport

Helpful Tips and Getting Started
Pull out the output tray extender to help collect
your prints.

The photo tray light illuminates when the photo tray is
pushed in. To use the main paper tray, disengage the
photo tray by pulling it towards you

You can access and use the AiO Home Center by double-clicking on the icon on your desktop.
You can use Kodak Home Center to browse, print, copy,
scan, and configure your AiO Printer from the computer.

Kodak Home Center Software

You can use Kodak EasyShare to transfer, view, and
work with your digital pictures and videos, if installed.

EasyShare Software

www.kodak.com/go/aiosupport

Control Panel Features

Display photos, messages,
status, and menus.

Displays the Proofsheet
menu when there are
pictures on an inserted
memory card or
connected USB host
device.

EasyShare 5300

Rotates the picture on the
display.

All-in-One Printer

Rotate

Zoom

Proofsheet

Transfer

Photo

Zooms in or out in .05X
increments.

Scan

Copy

Transfers images from a
device connected to a
USB host port, PictBridge,
or (PTP) PictureTransfer
Protocol.

Help

Displays the Main menu
on the LCD screen.
Cancel

On/Off

Displays the Help menu
on the LCD screen.

Attention

Indicates attention is
needed. When illuminated,
see LCD screen for further
instruction.

www.kodak.com/go/aiosupport

Troubleshooting
If you have additional questions about troubleshooting this device, please visit
www.kodak.com/go/5300aiosupport
PROBLEM:
I cannot get a calibration sheet to print.
SOLUTION:
When necessary, you can force a calibration sheet to print by following these steps:
1. Press Menu, select Calibrate Printer and press OK.
2. Select Print Calibration Page and press OK.
3. When the print comes out, place it at the front, right corner of the scanner glass.
4. Close the scanner lid and press START.
PROBLEM:
My calibration page printed on plain white text paper.
SOLUTION:
Follow the directions as listed in steps 3-4. Calibration will work successfully on both plain white paper and
photo paper.
PROBLEM:
I cannot print to my desired paper type.
SOLUTION:
Check to see if the photo tray is pushed in. You can do this by checking if the green photo tray light is
illuminated. If it is, all prints will be produced from this tray. If you want to print from the main tray, pull out
the photo tray by lifting the photo tray lid and sliding the paper tray toward you.
PROBLEM:
I have a paper jam.
SOLUTION:
1. Press in the tabs on the rear access door to remove the door.
2. Gently pull the paper out of the rollers. IMPORTANT: If the paper tears while removing it, check inside
the printer for torn pieces of paper and remove them. Additional jams are likely to occur if all of the torn
pieces are not removed.
3. Replace the rear access door. Gently push the door forward until it snaps into place.
Is Further Troubleshooting Required?
If you need further information to help answer your
questions, please contact Technical Support and
have your KSN number ready. Your KSN number can
be found on the printer by lifting the printer access door
as shown.

KODAK SERVICE NUMBER
F330065

*F330065*
*F330065*

www.kodak.com/go/aiosupport

More Accessories

More Options

More Convenience

Wireless
2.0 USB
Bluetoot
h Adapter

The KODAK EasyShare All-in-One Printer gives you more. Be sure to visit our online store to select from our
full line of supplies and accessories at www.kodak.com/go/AiO
Kodak's Inkjet Photo Paper
Get prints that look great the first time with Kodak's unique backprint technology that automatically enables
optimized prints.
Value Packs
Save up to 50% on everything you print and pay as low as 10 cents a print with our ink and paper Value
Packs.
Two-sided Printing Accessory
It's easy to print both sides of your document with the Kodak EasyShare 5000 Series Two-Sided Printing
Accessory.
Wireless Adaptor
Go wireless with the Kodak Wireless 2.0 USB Bluetooth Adaptor.
Note: A USB 2.0 cable is required to connect your Kodak All-in-One Printer to your Windows or Macintosh
OS computer. Available in the Kodak online store or see your local retailer.

www.kodak.com/go/aiosupport

Safety
- Read and follow these instructions before using KODAK products.
- Always follow basic safety procedures.
- Follow all warnings and instructions marked on the equipment.

WARNING STATEMENTS
- Do not expose this product to liquid, moisture, or extreme temperatures. KODAK AC adapters are intended
for indoor use only. The use of controls, adjustments, or procedures other than those specified herein may
result in exposure to shock and/or electrical or mechanical hazards.
- Keep ink cartridges out of reach of children. Ink may be harmful if swallowed.
- Do not place your AiO Printer on an unstable cart, stand, bracket, or table. Injury to persons and damage to
the equipment may occur.
- The use of an accessory attachment that is not recommended by Kodak, such as an AC adapter, may cause
fire, electric shock, or injury.
- Pushing objects through the equipment openings can result in an electric shock or risk of fire.

CAUTIONARY STATEMENTS
- Adjust only those controls covered in the operating instructions.
- Do not disassemble this product; there are no user-serviceable parts inside. Refer servicing to qualified
service personnel.
- The AC adapter power supply is equipped with 3-wire grounding type plugs. If you cannot insert the plug
into the power outlet, contact an electrician to check or replace the power outlet.
- Do not plug the AC adapter into a household extension cord.
- If the power cord or plug is frayed or damaged, the equipment gets wet, or the equipment does not operate
normally when the operating instructions are followed, unplug your AiO Printer from the power outlet and
contact Kodak qualified service personnel for further instructions.
- For added protection from damage during a lightning storm, or any time when your AiO Printer and it's
associated AC adapter will be left unused for long periods of time, unplug the AC adapter from the power
outlet and any attached fax line from the printer.
- To reduce the risk of fire, use only 26 AWG or larger telecommunication line cord.
- To prevent your AiO printer from overheating do not place it near a heat register, or install it in a cabinet
without proper ventilation.
- Do not use your AiO Printer near water or spill liquid on it.
- Unplug the equipment from the wall outlet before cleaning.
- Dropping your AiO Printer may damage the housing and result in extensive damage that will require repair
by a qualified technician to restore normal operation.
- Excessive dust levels may damage internal parts.
For more information, go to www.kodak.com/go/MSDS

www.kodak.com/go/aiosupport

Limited Warranty
Limited Warranty
Kodak warrants Kodak consumer electronic products and accessories ("Products"), excluding batteries, to be free from
malfunctions and defects in both materials and workmanship for one year from the date of purchase.
Retain the original dated sales receipt. Proof of the date of purchase will be required with any request for warranty
repair.
Limited Warranty Coverage
Warranty service is only available from within the country where the Products were originally purchased. You may be
required to send Products, at your expense, to the authorized service facility for the country where the Products were
purchased.
Kodak will repair or replace Products if they fail to function properly during the warranty period, subject to any
conditions and/or limitations stated herein. Warranty service will include all labor as well as any necessary
adjustments and/or replacement parts. If Kodak is unable to repair or replace a Product, Kodak will, at its option,
refund the purchase price paid for the Product provided the Product has been returned to Kodak together with proof of
the purchase price paid. Repair, replacement, or refund of the purchase price are the sole remedies under this warranty.
If replacement parts are used in making repairs, those parts may be remanufactured. or may contain remanufactured
materials. If it is necessary to replace the entire Product, it may be replaced with a remanufactured Product.
Remanufactured Products, parts and materials are warranted for the remaining warranty term of the original Product,
or 90 days after the date of repair or replacement, whichever is longer.
Limitations
This warranty does not cover circumstances beyond Kodak's control. This warranty does not apply when failure is due
to shipping damage, accident, alteration, modiﬁcation, unauthorized service, misuse, abuse, use with incompatible
accessories or attachments (such as third party ink or ink tanks), failure to follow Kodak's operation, maintenance or
repacking instructions, failure to use items supplied by Kodak (such as adapters and cables), or claims made after the
duration of this warranty.
KODAK MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY FOR THIS PRODUCT, AND DISCLAIMS THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. In the event that the
exclusion of any implied warranty is ineffective under the law, the duration of the implied warranty will be one year
from the purchase date or such longer period as required by law.
The option of repair, replacement, or refund is Kodak's only obligation. Kodak will not be responsible for any special,
consequential or incidental damages resulting from the sale, purchase, or use of this product regardless of the cause.
Liability for any special. consequential or incidental damages (including but not limited to loss of revenue or proﬁt,
downtime costs, loss of the use of the equipment, cost of substitute equipment, facilities or services. or claims of your
customers for such damages resulting from the purchase use or failure of the Product), regardless of cause or for
breach of any written or implied warranty is expressly disclaimed.
Your Rights
Some states or jurisdictions do not allow exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. Some states or jurisdictions do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you speciﬁc rights, and you may have other rights which vary from state to state or by jurisdiction.
Your statutory rights are not affected.
Outside the United States and Canada
In countries other than the United States and Canada, the terms and conditions of this warranty may be different.
Unless a speciﬁc Kodak warranty is communicated to the purchaser in writing by a Kodak company, no warranty or
liability exists beyond any minimum requirements imposed by law, even though defect, damage, or loss may be by
negligence or other act.

www.kodak.com/go/aiosupport

Blank

REGISTRATION HAS ITS REWARDS—including a terriﬁc offer.
Register your KODAK All-in-One Printer and get great support, expert tips, free
software downloads—plus a phenomenal deal on inkjet supplies to get you started.
Simply register right away when prompted during software installation or on the
web at www.kodak.com/go/register

REGISTRATION TAKES A MINUTE—BUT THE REWARDS ARE LASTING.
Inkjet supplies offer valid for U.S. residents only.

Any questions?
Look here for answers:
www.kodak.com/go/5300aiosupport

User’s Guide - The User Guide is installed with your Kodak AiOSoftware and is located:
Windows: Program Files
Kodak
Printer
Center
Help
Macintosh: Library Documentation Kodak AiO Printers
For printer support, please call 1-800-421-6699

Eastman Kodak Company
Rochester, NY 14650 U.S.A.
© Eastman Kodak Company, 2007
MC/MR/TM: Kodak, EasyShare.
Printed in the U.S.A.
The Bluetooth® trademarks are owned by the Bluetooth SIG, Inc.
Windows® is a registered trademark of Microsoft Corporation
Macintosh® is a registered trademark of Apple Computer, Inc.
1K2682

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2007:12:07 15:57:49-08:00
Create Date                     : 2007:12:07 15:53:35-08:00
Metadata Date                   : 2007:12:07 15:57:49-08:00
Format                          : application/pdf
Title                           : untitled
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Document ID                     : uuid:991c01a4-838a-41c2-a4c4-9c260430c803
Instance ID                     : uuid:0e6625f2-58df-478a-8996-d5d1ba04165a
Page Count                      : 20

EXIF Metadata provided by EXIF.tools

Kodak Easyshare 5300 Users Manual

Navigation menu

Versions of this User Manual:

Views

Navigation