Kodak Gen 5 Grd Users Manual

GRD to the manual e8a20f47-65ac-4776-89d4-b956442c8247

2015-02-04

: Kodak Kodak-Gen-5-Grd-Users-Manual-370319 kodak-gen-5-grd-users-manual-370319 kodak pdf

Open the PDF directly: View PDF PDF.
Page Count: 6

DownloadKodak Kodak-Gen-5-Grd-Users-Manual- Kodak-gen-5-grd-users-manual
Open PDF In BrowserView PDF
Kodak Gen 5 GRD, GRD7, GRDM & GR7M Film
Technical Information Instruction Sheet – TI2375
August 2006

Features / Customer Product Specifications
Kodak Gen 5 films are fast, high contrast, broad band red-sensitive film. Their sharp dots are capable of
high resolution at fine screen rulings. These films are optimized for exposure on film recorders that use a
helium-neon laser (633 nm) or a red laser diode (630 to 670 nm) as the exposing source.
These films feature high processing speeds (development in as little as 20 seconds) and low
replenishment rates in rapid-access developer and fixer, which contribute to improved productivity and
reduced operating costs.
Gen 5 films are coated on a dimensionally stable Estar base with antistatic and surface properties to
ensure dependable transport and handling behavior.

Safelight Recommendations
Use an EncapSulite T20/ND.75 safelight or equivalent. Keep the film at least 1.2 metres (4 feet) from
the safelight. Do not expose the film to safelight illumination for longer than two minutes.
European office:

US office:

EncapSulite International Ltd.
Auf dem Loor 14a
51143 Köln Germany
Phone: 49 (0)2203-8 37 37

EncapSulite International Inc.
1220 Bamore Road
Rosenberg, TX 77471
Phone: 1-281-239-0225

Storage
Keep unexposed film and processed film in a cool, dry place, preferable at a temperature of 70° F (21° C)
or lower and 50% RH. Process film as soon as possible after exposure.

Exposure
These films are intended for use on film recorders that use a 633 nm helium-neon (HN) laser
or a 630 to 670 nm red laser diode (RLd) as the exposing source. Follow the exposure
procedures recommended by the equipment manufacturer.

Mechanized Processing
Notice: Observe precautionary information on products labels and on the Material Safety Data Sheets.
Gen 5 films can be processed in Kodak RA 2000 developer and replenisher, diluted either 1:2 or 1:4. To
achieve the highest productivity (20-second development time) and the best image quality and linearity,
use a 1:2 dilution. To achieve the maximum savings in chemical usage, use a 1:4 dilution and a 30-second
development time.
The recommended starting points for development and replenishment, using Kodak RA 2000 developer
and replenisher (1:2) are:

Rapid Access Processors, 20 seconds at 95° F (35° C)
Tank Turnovers per Week

Percent Exposed Area

Minimum of 0.5

50%

Basic Replenishment Rates
0.23 mL/sq in (350 mL/ sq m)

The recommended starting points for development and replenishment, using Kodak RA 2000 developer
and replenisher (1:4) are:

Rapid Access Processors, 30 seconds at 95° F (35° C)
Tank Turnovers per Week

Percent Exposed Area

Minimum of 0.5

© Kodak, 2006. Kodak and Gen 5 are trademarks of Kodak.

50%

Basic Replenishment Rates
0.30 mL/sq in (465 mL/ sq m)

Kodak Gen 5 GRD, GRD7, GRDM & GR7M Film
Technical Information Data Sheet – TI2375
August 2006

1. Support
Dimensionally Stable Support
GRD, GRDM

4 mil (0.004 in., 0.10mm)

Estar base

GRD7, GR7M

7 mil (0.007 in., 0.18mm)

Estar thick base

2. Dimensional Stability
Dimensional stability is an all-inclusive term. In photography, it applies to size changes caused by
changes in humidity and in temperature, and by processing and aging. The dimensional properties of The
Estar base may vary slightly in different directions within a sheet; the differences that may exist, however,
are not always aligned with the length and width directions:
Data for the 4-mil products (GRD, GRDM):

Thermal Coefficient of Linear Expansion
Unprocessed or Processed

0.001% per ° F (0.0018% per ° C)

Humidity Coefficient of Linear Expansion
Unprocessed

0.0017% per % RH

Processed

0.0016% per % RH

Processing Dimensional Change
Dependent on drying conditions

2. Reciprocity
With recommended processing, the reciprocity speed change is negligible within exposure range of
1/1000 second to 1 billionth second; there is no change in contrast.

4. Graphs1
Using Kodak RA 2000 developer and replenisher (1:2)
Characteristic
A. (10-98)
B. (12-98)
Spectral Sensitivity
C. (10-98)

1

NOTICE: While the data presented are typical of production coatings, they do not represent standards
that must be met by Kodak. Varying storage, exposure, and processing conditions will affect results. The
company reserves the right to change and improve product characteristics at any time.

© Kodak, 2006. Kodak and Gen 5 are trademarks of Kodak.
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Company                         : Forward branding & identity
Source Modified                 : D:20070424180437
Create Date                     : 2007:04:24 14:04:43-04:00
Creator Tool                    : Acrobat PDFMaker 7.0.7 for Word
Modify Date                     : 2007:04:24 14:05:35-04:00
Metadata Date                   : 2007:04:24 14:05:35-04:00
Document ID                     : uuid:fd18a0a3-3db4-47d5-88ab-1765f31ce275
Instance ID                     : uuid:7b174305-aa26-47ec-9524-1b8911f299a0
Version ID                      : 6
Format                          : application/pdf
Title                           : Title
Creator                         : Rob
Subject                         : 
Headline                        : 
Page Count                      : 6
Page Layout                     : OneColumn
Language                        : EN-US
Author                          : Rob
EXIF Metadata provided by EXIF.tools

Navigation menu