Kodak K100 Operating Instructions

K100 - Operating Instructions k-100 Free User Guide for Kodak Camcorder, Manual

: Kodak Kodak-K100-Operating-Instructions-787638 kodak-k100-operating-instructions-787638 kodak pdf

Open the PDF directly: View PDF .
Page Count: 32

CINE-KODAK

K-100

CAMERAS

• This instruction manual is for the Cine-

Kodak K-I00 Camera and the Turret Model.

On the turret model you can mount three

picture-taking lenses with matching view-

finder lenses - thus allowing you to change

quickly from wide-angle to medium to tele-

photo shots. The Cine-Kodak ~-100 Camera

has a single taking lens and viewfinder lens.

Any of the lenses, Ifimm to I52mm with C

mounts, can be used. The cameras use either

single- or double-perforated Ifimm film.

Movies are more than just pictures. Mere-

ly following the rules for proper camera op-

eration will produce technically acceptable

pictures. Add to this imagination and artis-

tic effort and your pictures become good

movies - movies that you will be proud to

show and that your friends will really enjoy

seeing.

Simple instructions are given on the next

6 pages. For more detailed information, read

further in the manual.

wind the motor

Turn the

WINDING HANDLE

clockwise until

the

SPRING MOTOR DIAL

is at about 40 feet.

remove the cover

Turn the locking knob counterclockwise

and lift off the cover.

Before making any important pictures, it

is always well to shoot a roll of film. This

will give you practice in camera operation

and provide a check on your results. If you

have any questions, your dealer will be glad

to help.

T. M. REG. U. S. PAT. OFF.

p

"

Serial Numbers: The serial number of your camera is

stamped on the rear carry handle clip. The serial number

of the lens is stamped on the front of the lens barrel.

Record these numbers with your personal papers for posi-

tive identification of the camera and lens. In case of loss

or theft, report the fact to your Kodak dealer and to the

local police at once.

EASTMAN KODAK COMPANY

1-57

•

ROCHESTER 4, N. Y .

PRINTED IN THE UNITED STATES OF AMERiCA

The Kodascope Pageant Sound Projector,

ac or de, 105

to 125 volts, has a capacity of 2000 feet of film. It

operates at both sound and silent speeds. An acces-

sory microphone plugged into the amplifier enables

you to narrate your silent movies and to use the

Pageant as a public address system.

The Kodascope Analyst Projector,

60-cycle ac only, can

project movies in normal fashion on a screen and also

in natural light on its own built-in screen. It also

operates by a remote control switch which provides

immediate

forward or reverse operation. It is ideally

suited for such special applications as sports analysis,

motion study, etc.

Kodak Cine Photoguide

Take the guesswork out of movie making with the

Kodak Cine Photo guide. Here is a 32-page pocket-

sized booklet with a durable leather-like cover. It con-

tains on-the-spot movie-making information for both

common and unusual lighting conditions. Among the

subjects covered by convenient dial computers, tables,

and brief text are: indoor and outdoor exposure,

close-up photography, movie continuity, field size and

depth-of-field tables for many Kodak Cine Lenses and

supplementary lenses, and film and filter data. See

your Kodak dealer.

28

2

load the camera

Remove the empty take-up spool. Unroll

about two feet

01

film from the. new spool

and place the spool of film on the

SUPPLY

SPINDLE,

square hole down.

Follow the film path as shown by the red

lines and arrows on the plate. Push the film

down and, at the same time, pull it forward

to engage the

FILM SPROCKET

teeth in the

film perforations. The take-up spool turns in

the direction of the arrow shown on the

camera.

Press down the

EXPOSURE LEVER

for a

moment and check the following:

1

The spools must be seated all

the way down on the spindles.

Check to see that

.the

film

2

moves evenly and follows the

film-guide lines.

CAUTION: It

is

possible to run film through

the camera without taking satisfactory pic-

tU1"eS,if the film perforations are not engaged

by the PULLDOWN. This is because the driv-

ing force then comes irom the sprocket only.

Set the

FILM METER

at

LOAD.

Then replace

the cover and turn the locking knob clockwise

to secure the cover. Run the camera until the

film meter is at 100.

,II

.It

I,·'

i

Kodascope Proiectors

The Kodascope projectors answer all your needs for

sound or silent motion pictures. The projectors come

equipped with powerful 750-watt lamps amply bright

for average projection. A 1000-watt lamp can be used

for large audiences. The projectors are fitted with a

2-inch

f

/1.6 Lumenized Kodak Projection Ektanon

Lens. The following Kodak Projection Ektanon

Lenses are also available: a 1Yz-inch

f

/2.0, a 3-inch

f

/2.0, and a 4-inch

f/2.5.

The Kodascope projectors are smartly styled, light,

compact, and easy to operate. All are permanently

lubricated.

The Kodascope Royal Projector,

illustrated above, is de-

signed to give the best in silent movie projection. It

operates on ac or

de,

105 to 125 volts, both forward

and in reverse, and has a speed control knob for rapid

rewind.

27

hand crank

The Cine-Kodak K-IOOCamera can be hand-cranked

either forward or reverse for special effects. No more

than two feet of film should be reverse wound at a

time. This is accomplished by use of the Cine-Kodak

K-IOOHand Crank. See your Cine-Kodak dealer.

electric motor drive

The camera is adaptable to electric motor drive by

using the Cine-Kodak K-IOOMotor Drive Shaft avail-

able from your Cine-Kodak dealer.

field case

A fine instrument deserves good care, and there is no

better way of caring for your camera than to keep it

in a suitable case. Not only will its appearance be

benefited, but the camera will actually take better

pictures longer, if it is properly cared for. The field

case not only protects the camera from scuff-marks

and bangs, but permits it to be ready for picture tak-

ing at a moment's notice. The case will also help keep

your camera clean; dust collecting on the lens sur-

face requires frequent brushing off to maintain pic-

ture clarity, snap, and brilliance.

26

1"

I

3

set the speed dial

The speed dial can be turned until anyone of

five speeds (16, 24, 32, 48, or 64 frames per

second) is opposite the index mark.

For normal screen action, when using a si-

lent projector, use the 16 frames per second

speed. Film to be run at sound speed should

be exposed at 24 frames per second.

select the lens

Select the desired taking lens and corre-

sponding viewfinder lens. Rotate the turret

until these lenses are in the proper picture-

taking position.

select the lens opening

Slide the card supplied with each roll of

Kodak film into the Cine-Kodak Universal

Guide on the side of the camera. One side of

the card is for movie making outdoors-the

other side is for use indoors with photo-

graphic flood lamps.

Turn the dial on the guide so that the se-

lected camera speed is opposite the proper

light condition; then use the lens opening

indicated.

4

KODACHROME filM

Oaylight Type

Filters are used in black-and-white photography to

obtain correct tone rendering, to create special sky

and moonlight effects, to cut haze, and to obtain con-

trast between areas differing in color. The wise use

of a filter will often make the difference between ex-

cellent photography and mere record.

Correction filters aid in reproducing colors as

grays in the relative brightness that the eye sees

them. Oftentimes blue reproduces too light without

a filter, and there is no contrast between sky and

clouds. Filters also cut bluish atmospheric haze on

distant scenes.

A filter such as the Kodak ND-3 Filter is needed

when Cine-Kodak Tri-X Film is used in sunlight.

Filters such as the K2, G, A, and Xl are recom-

mended for black-and-white photography. All are

supplied as Kodak Combination Lens Attachments in

series sizes. Additional information on filters comes

with your film.

Cine-Kodak Filters

;

WITH FILTER

Kodachrome Filters

A filter such as the Kodak Skylight Filter

is recommended

for Kodachrome Film Daylight Type, for pictures in

open shade under a clear blue sky, pictures made on

overcast or hazy days, distant scenes (mountain or

marine views), sunlit snow scenes, and aerial photo-

graphs.

A filter such as the Kodak Photoflood Filter No. 80B (for

Kodak Daylight Type CoJor Films)

can be used if regular

daylight Kodachrome is to be exposed indoors with

photographic flood lamp illumination. Type 'A film is

preferred for photographic flood lamp illumination.

A filter such as the Kodak Daylight Filter for Kodak Type A

Color Films

is recommended if Kodachrome Film Type

A is to be exposed outdoors in daylight. Exposures

with this filter are the same as those for Kodachrome

Film Daylight Type.

25

cine aids

r

combination lens attachments

O·

~

,

Kodak

Adapter Ring

Kodak

Portra Lens

Kodak

Wratten Filter

Kodak

Lens Hood

set the focus

Turn the front collar of the lens barrel until

the figure corresponding to the distance

from the camera to the subject is at the

index.

The Kodak Combination Lens Attachments permit

the use of any desired combination of Kodak Portra

Lens, Kodak Pola-Screen, and Kodak Wratten Filter.

See table below for attachment series number and

adapter ring number for the various lenses.

Kodak Adapter Rings screw into the lens barrel.

The Kodak Retaining Ring is unscrewed from the

Adapter Ring to admit a filter or Portra Lens. The

retaining ring is then screwed back into place.

To use a filter and a Portra Lens at the same time,

obtain another Kodak Retaining Ring. The Portra

Lens must always be nearer the camera lens.

set the lens opening

Turn the collar of the lens barrel until the

proper lens opening is at the index. The lens

in the illustration is set for

1/8

and 15 feet.

Attachment

JI

Lens Series Adapter Ring

n

Number Number

~

1

15mm,

1/2.5

6 28

(SCREW-IN)

I

(WIDE-ANGLE)

I

Kodak Cine Ektar Lenses

25mm,

1/1.9

5 22

(SCREW-IN)

("C" Mount)

25mm,

1/1.4

6 26

(SCREW-IN)

102mm,

f

/2.7

6

NONE REQUIRED

152mm,

f

/4.0

6

NONE REQUIRED

15mm,

1/2.5

6 28

(SCREW-IN)

(WIDE-ANGLE)

25mm,

1/1.9

6 27

(SCREW-IN)

Kodak Cine Ektar

25mm,

1/1.4

6 27

(SCREW-IN)

Interchangeable Lenses ,

40mm,

1/1.6

6 27

(SCREW-IN)

("5" Mount)

63mm,

1/2.0

6

NONE REQUIRED

102mm,

1/2.7

6

NONE REQUIRED

152mm,

1/4.0

6

NONE REQUIRED

I

focus the viewfinder

Hold the camera as shown and focus the sub-

ject in the finder by turning the finder focus

knob back and forth until the image is sharp.

frame and shoot

Frame the picture within the finder rectan-

gular mask and push the exposure lever

downward to start taking pictures.

Tri-X Reversal

is a very fast black-and-white film par-

ticularly suitable for commercial, television, indus-

trial, and athletic photography where adverse light-

ing conditions are frequently encountered.

Cine-Kodak Negative Films

Plus-X

Tri-X

The use of these black-and-white films results in a

negative from which positive projection prints can

be obtained. They are intended for processing by

independent commercial laboratories or by the user.

magnetic sound track for 16mm film

Kodak Sonotrack Coating-a

magnetic sound track coat-

ing service-is now available for processed, single-

or double-perforated Kodachrome or black-and-white

I6mm Cine-Kodak film.

Sonotrack Coating can be applied to film taken at

either sound or silent speed. It is placed on the side

of the film that faces the projection lamp.

Kodak Sonotrack Coating is available in three

widths. Single-perforated I6mm film having no

sound track will be Sonotrack coated the full width

of the track area. When an optical sound track is on

the film, it will be Sonotrack coated half the width of

the optical track, unless you specify that the full

width of the optical track be coated. It is available in

edge-coating for double-perforated I6mm film.

Sonotrack Coating must be ordered through

your Kodak dealer. This coating can be or-

dered by your dealer after your 16mm Cine-

Kodak film has been processed. Unexposed

film will not be coated.

23

Cine-Ko ak

ilrns

All16rn11~ films perforaied. one

or two edges can be used.

Kodachrome Film

Kodachrome Film, Daylight Type reproduces colors with

startling realism when exposed under daylight con-

ditions.

Kodachrome Film, Type A is color-balanced for photo-

graphic flood lamps and requires no filter when so

used. The film can also be used for taking pictures

in daylight with a filter such as the Kodak Daylight

Filter for Kodak Type

A

Color Films (see page 25).

Processing-Exposed Kodachrome Film may be taken

to a dealer who will arrange for processing at a labo-

ratory of your choice. If you prefer, you may mail it

to a Kodak Laboratory using a Kodak Processing

Mailing Label or to any other laboratory processing

Kodachrome Film. The mailing labels may be ob-

tained from your dealer, and film sent in with these

labels will be returned to the same dealer. Payment

will be made to your dealer who can also order full-

color duplicates of your Kodachrome Films.

Cine-Kodak Black-and-White Reversal Films

These films are sold at a price which does not include

processing by the Eastman Kodak Company. They

are intended for processing by independent commer-

ciallaboratories or by the user. Conventional reversal

processing provides a positive image for projection.

Duplicate prints can also be obtained from many

commercial laboratories.

Plus-XReversal is a very fine-grain film used in general

black-and-white picture making. It can be used with

natural or artificial illumination.

22

T

complete operating

winding motor

•

8

loading

•

8

camera speed

•

12

using the turret

•

12

lenses

•

13

focus 14

setting the lens opening 14

the viewfinder 1S

correction for close-ups 16

sighting 17

making exposures 18

shutter speeds 18

scene length 18

unloading and care of exposed film 19

pictures outdoors at night 19

animation by single-frame exposures 20

cine-kodak films 22

cine aids 24

.•

complete instructions

cleaning the lenses

The glass-air surfaces of the lens on your camera.have

been Lumenized to reduce internal reflections, flare,

and scattered light. This increases the brilliance of

black-and-white pictures and the color purity of

Kodachrome pictures. All Lumenized lenses appear

tinted by reflected light but this color has no effect

on the image.

To clean the lens, carefully brush off any dust or

grit with wadded Kodak Lens Cleaning Paper or a

fine camel's-hair brush. If necessary, wipe the sur-

faces gently with a wad of lens cleaning paper or a

clean, soft, lint-free cloth. Always wipe with a circu-

lar motion. Fingerprints, oil spots, or other scum

deposits can be removed with a drop of Kodak Lens

Cleaner on the cloth. DO NOT USE ALCOHOL.

winding motor

Be sure the

EXPOSURE LEVER

is in the off or horizontal

position. Raise the

WINDING HANDLE

on the side of

the camera and fit the opening in the handle over the

square end of the shaft. Turn the winding handle

clockwise until the

SPRING MOTOR DIAL

is at about 40

feet.

loading

Turn the locking knob counterclockwise to the

UN-·

LOCKED

position and lift off the cover.

Take the empty take-up spool out of the camera.

Remove a spool of Cine-Kodak film from its carton

cleaning the film channel

Open the pressure plate as far as it

will go. With the ball of the thumb,

rub off any accumulation of dirt on

the polished tracks of the plate.

With a match covered with a clean

cloth that has been dipped in Stod-

dard's Solvent, such as Sovasol No.

5 (Socony-Vacuum Oil Company) or

Sunoco Spirits (Sun Oil Company),

remove any accumulation on the

tracks of the aperture plate. (Do not

use alcohol as a cleaning agent.) Re-

move any dust or lint on the edges

of the rectangular aperture. Be ex-

tremely careful not to scratch the

polished surfaces over which the

film travels. Never scrape the tracks

with a metallic tool.

21

8

animation

by

single-frame exposures

One of the most absorbing fields made possible by

your camera is animation-the movie method of

breathing life into inanimate objects. You may wish

to try the simpler type where chessmen play their

own game, and books, ash trays, etc., roam around

over a table top. Or you may be sufficiently fascinated

by the almost limitless possibilities of animation to

try your hand at the more complicated types.

To animate a subject, expose a single frame, move

the subject slightly, expose another frame, move the

subject again, and so on. If a

certain

movement is

to take place in one second on the screen with the

projector operated at normal (16) speed, 16 single-

frame exposures will be required.

Applications of animation include: animated

titles, graphs that draw themselves, machines, and

other manufactured products that assemble them-

selves.

The Cine-Kodak K-100 Cameras are also excel-

lent for time-lapse photography-a method of greatly

accelerating a period of time. The growth of a flower

to full bloom, rapid movement of street traffic, cloud

formations for an entire day, can all be depicted in

a few seconds' time with time-lapse photography.

Expose one frame at a time at intervals which will

produce the desired effects. The interval between

exposures will vary according to subject matter.

To make single-frame exposures, set the speed dial

at 16 frames per second and push

up

the exposure

lever once for each exposure. Each single frame is

exposed for 1/20 of a second. If the Universal Guide

is used for determining the exposure, one stop small-

er than the exposure indicated for 16 frames per sec-

ond should be used; for example, if the exposure

guide reading is

f

/5.6 for 16 frames per second, the

lens opening should be set at

f/8.

20

and metal can. Remove the paper band around the

film. Save the paper band, carton and metal can to

send the film to your dealer for processing.

Pull out about two feet of film, Be especially careful

not to let too much film unwind or the film on the spool

will be fogged. Place the spool of film on the

SUPPLY

SPINDLE

with the square hole down. Make sure that the

spool is properly seated-the end of the supply spindle

should project through the round hole in the spool.

Following the red film-guide lines and arrows, in-

sert the film between the

UPPER FILM GUIDE

and the

FILM SPROCKET.

Push the film down and at the same

time pull it forward to engage the sprocket teeth in

the film perforations. Open the

PRESSURE PLATE

only

enough to make it stay open. Do not push it beyond

this open position. (The illustration below shows the

pressure plate fully opened in order to show the pull-

down.)

Following the film-guide lines, pass the film

between the pressure plate and the

APERTURE PLATE.

Be sure the film is placed all the way into the film

channel.

Close the pressure plate and move the film back and

forth until the

PULLDOWN

engages a film perforation

9

10

NOTE:

It is extremely important that the film

perforations be engaged by the pulldown.

Check again to see if the film is properly lo-

cated in the film channel and follows the red

lines so that correct loops, which are also

important to the functioning of the camera,

are formed. Then inspect the pressure plate to

be sure

it

is seated correctly with respect to

the film and the film channel.

Follow the red film-guide lines and pass the film

between the

LOWER FILM GUIDE

and the film sprocket.

Engage the sprocket teeth in the film perforations.

Insert the end of the film in the slot in an empty

take-up spool. Turn the spool one turn to securely at-

tach the film to the spool. Place the spool, square hole

down, on the take-up spindle. Turn the take-up spool

clockwise with your finger until the film appears

snug on the spool.

Press down the exposure lever for a moment and

check the following conditions:

1

The spools must be seated all the way

down on the spindles.

2

The film must move evenly and must

follow the film-guide lines.

film meter

Set the film meter at

LOAD.

Then replace the cover

and turn the locking knob clockwise to

LOCKED,

to se-

cure the cover. Run the camera until the film meter

is at 100.

unloading and care of exposed film

pictures outdoors at night

......-

~

The usable length of film has been exposed when the

film meter shows O. Before removing the camera

cover, run off the trailer as follows:

Run the camera until the line below 0 on the film

meter is opposite the pointer. The end of the film can

usually be

heard

as it leaves the film channel. Remove

the cover; then remove the full spool of exposed film

from the take-up spindle. For best results have the

film processed as soon as possible after it is exposed.

See the directions that accompany your film.

Before rethreading, make sure the gate is free of

dirt, pieces of film, or foreign particles.

Unusual and artistic effects in color or black-and-

white can be obtained at night with your camera.

Brilliantly lighted streets or the theater districts of

large cities make interesting shots. Lighted streets

and squares photographed on wet nights or after a

heavy snow are especially attractive. Animated elec-

tric signs are always good subjects. For best results,

photograph only brightly illuminated scenes.

Use Cine-Kodak Tri-X Reversal or Cine-Kodak

Tri-X Negative Film for sporting events on dull

days, indoor-lighted events, and night-lighted out-

door events.

making exposures

With the spring motor fully wound, about 40 feet of

film can be exposed. If several consecutive scenes

must be photographed, be sure to wind the spring

when the spring motor dial indicates that the motor

will run about 5 to 10 feet of film. However, it is

best to wind the spring after each scene. In this way

the camera is always ready for use.

To start the motor, push the exposure lever down-

ward. To stop, release the lever. Pressing the lever

all the way down locks it in the running position.

11

scene length

About 6 feet of film (15 seconds at 16 frames per

second) is sufficient for average scenes in which the

action is continuous. However, the length of a scene

should be governed by the nature of the subject.

Landscape shots, for example, can be of greater

duration than scenes with brief, fast-moving action.

shutter speeds

The exposure data is given on the basis of 16 frames

per second. The use of any faster speed requires a

larger lens opening (stop); for example, at 32 frames

per second, the lens opening should be 1 stop larger;

at 64 frames per second, the lens opening should be

2 stops larger. The Cine-Kodak Universal Guide

shows the proper lens opening for each camera speed.

Exposure Time in Seconds

Single Frame 1/20

EXPOSURE TIME

PE~

FRAME

Angle of Opening

in Shutter 165

0

16 Frames per Second 1/35

24 Frames per Second 1/50

32 Frames per Second 1170

48 Frames per Second

1/100

64 Frames per Second

1/140

camera speed

For normal screen action with silent pictures, set the

camera speed at 16 frames per second.

If sound is to be dubbed in, or if you expect to run

the film at sound speed, the camera should be oper-

ated at 24 frames per second. When setting the

camera speed, remember that any camera speed

faster

than projection speed will produce slower-

than-normal action in the projected picture.

The speed dial can be turned until anyone of five

speeds (16, 24, 32, 48, or 64 frames per second) is

opposite the index mark. Intermediate speeds can be

obtained by turning the dial until the index mark is

between any two numbers.

using the turret

The turret rotates on a central axis, and, when

turned, brings each lens successively into picture-

taking position. To make certain that each lens is

correctly positioned, the turret snaps into place for

each lens.

With the turret snapped in place, the taking lens is

at the upper right and lined up with the film plane

mark on the camera cover. The viewfinder lens for

that particular taking lens is at the top of the turret.

If a 15mm lens and 152mm lens are used on the

turret, the 152mm lens must be in the lower position

when the 15mm lens is in the picture-taking position.

To avoid disturbing the lens settings when rotat-

ing the turret, grasp the two adjacent viewfinder

12 lenses.

field of view.

The heavy, upper right cross is the ref-

erence cross.

For correction when filming a subject 2V2to 7 feet

from the camera, with the 25mm lens, note the posi-

tion of the reference cross with respect to some point

on the subject. Then move the camera so that the

middle cross is at the position previously occupied by

the reference cross. The camera is now in position to

photograph the field previously outlined by the mask.

For correction at 1V2 to 2% feet, with the 25mm

lens, use the lower cross instead of the middle cross.

For other lenses the crosses are to be used for dif-

ferent subject distances. See the table below.

Viewfinder Lenses 15mm

I

25-40-50mml 63-75mm 1102-152mm

When Film-to-Sub.iect Distance is

Use Lower Cross 1 Foot to 1% Feet to 2% Feet to 3V2Feet to

11/2Feet 2% Feet 4 Feet 6 Feet

Use Middle Cross 1V2Feet to 2% Feet to 4 Feet to 6 Feet to

4Y2Feet 7 Feet

9

Feet 12% Feet

sighting

Hold the camera as shown in the illustration. Brace

the elbows against the side of the body to steady the

camera. The Cine-Kodak K-100 Cameras can be hand-

held. However, the pictures, when projected on the

screen, will appear much steadier if the camera is

placed on a tripod while pictures are being taken.

The tripod socket is on the bottom of the camera.

17

When replacing a finder lens, insert the lens into the

lens retaining mount so that the stud on the lens

mount fits in the slot in the lens tube; then tighten

the retaining collar.

correction for close-ups

Because the finder and the taking lens are separated,

they do not always cover the same area and slight

compensations are necessary when filming subjects

very near the camera. To simplify framing for close-

ups, three crosses have been placed within the finder

REFERENCE CROSS

2'12

FT. TO 7 FT.

REFERENCE CROSS

1'12

FT. TO 2% FT.

16

"

lenses

J;

\!

~

Kodak Cine Ektar Lenses, 15mm

1/2.5,

25mm

1/1.4,

25mm

1/1.9,

102mm

1/2.7,

and 152mm

1/4.0

in

type C mounts fit directly on this camera. A Kodak

Ektar

1/1.4

Converter, 25mm to 15mm, used with a

converter adapter, is available to fit the 25mm

1/1.4

lens with a type C mount. The Kodak Cine Ektar

Lens, 25mm

1/1.4,

with the converter in place, be-

comes a fast, wide-angle lens which covers a field

approximately 60% larger than a 25mm lens. This

reduction in focal length is accomplished without

loss of lens speed or of image quality.

By using a Kodak Cine Lens Adapter Type C the

following interchangeable Kodak Cine

Ektar

Lenses

can be used: a 15mm

1/2.5

wide-angle lens, a 40mm

1/1.6,

a 63mm

1/2.0,

a 102mm

1/2.7,

and a 152mm

1/4.0.

Viewfinder lenses are available for use with

15, 40, 50, 63, 75, 102, and 152mm focal length lenses.

For wider coverage than can be obtained with the

standard 25mm lens, use a 15mm wide-angle lens. The

wide-angle lens covers a larger field, about 60% more

than the 25mm lens. For large, clear pictures at long

range-close-ups of sports, wild life, children at play

-use a telephoto or long-focus lens.

Taking the image produced by a 25mm lens as

normal, the other lenses produce images- magnified

in direct ratio to their focal lengths. Thus the 63mm

lens produces an image 27'2 times larger than a

25mm lens; with the 152mm lens the image will be

6 times larger.

IMPORTANT: For best results when using a long-locus

or telephoto lens, brace the camera against a firm

support. Use a tripod. whenever possible.

These pictures are actual enlargements from a Cine-Kodak film of the

same subject photographed from the same distance with five different

Cine-Kodak lenses: A is 25mm; B is 40mm; C is 63mm; D is l02mm;

and E is 152mm.

13

focus

Check the focusing scale before each scene is photo-

graphed. The scale setting must correspond to the

camera-to-subject distance. Accurate focusing is

particularly important when making close-ups. When

the subject is four feet or less from the camera, meas-

ure the distance carefully to the small metal boss

with the

¢

on the camera cover. This marks the posi-

tion of the film plane. To focus, turn the

front

lens

collar so that the subject distance is at the index.

setting the lens opening

LENS OPENING

1.4

•

1.9

•

2.8

e

4

e

5.6

•

8•

11

•

16

•

22 •

The lens opening must be set to accommodate changes

in the light conditions. For example, on dull days or

in the shade, a larger lens opening is used, while in

bright sunlight a smaller lens opening is used. Lens

opening

f

/22 is the smallest opening;

f

/16 is larger

and admits about twice as much light. Each succeed-

ing marked opening doubles the light passing through

the lens.

The larger the number, the smaller the lens

opening.

Set the lens opening by turning the lens

collar until the proper number is at the index.

the viewfinder

The finder is a telescopic type finder. It is designed so

that with the 25mm viewfinder lens, the subject ap-

.pears full size. Adjust the finder focus by turning the

finder focus knob back and forth until the image is

sharp. For most people, proper adjustment of the

finder focus will allow you to change from one turret

position to another without further adjustment of

the finder focus. The rectangular mask which appears

in the finder is in focus at the same time as the sub-

ject so that a sharp definition of the field that is being

photographed can be seen.

The field outside the mask is also visible, so that

action outside the field being photographed can be

observed and the camera moved to include it if

desirable. '

When other lenses are used, a viewfinder lens

which matches the focal length of the taking lens

must be used. The table on page 17 shows the finder

lenses which are available. To remove the finder lens,

unscrew the retaining collar and lift out the lens.

focus

Check the focusing scale before each scene is photo-

graphed. The scale setting must correspond to the

camera-to-subject distance. Accurate focusing is

particularly important when making close-ups. When

the subject is four feet or less from the camera, meas-

ure the distance carefully to the small metal boss

with the

¢

on the camera cover. This marks the posi-

tion of the film plane. To focus, turn the

front

lens

collar so that the subject distance is at the index.

setting the lens opening

LENS OPENING

1.4

•

1.9

•

2.8

e

4

e

5.6

•

8•

11

•

16

•

22 •

The lens opening must be set to accommodate changes

in the light conditions. For example, on dull days or

in the shade, a larger lens opening is used, while in

bright sunlight a smaller lens opening is used. Lens

opening

f

/22 is the smallest opening;

f

/16 is larger

and admits about twice as much light. Each succeed-

ing marked opening doubles the light passing through

the lens.

The larger the number, the smaller the lens

opening.

Set the lens opening by turning the lens

collar until the proper number is at the index.

the viewfinder

The finder is a telescopic type finder. It is designed so

that with the 25mm viewfinder lens, the subject ap-

.pears full size. Adjust the finder focus by turning the

finder focus knob back and forth until the image is

sharp. For most people, proper adjustment of the

finder focus will allow you to change from one turret

position to another without further adjustment of

the finder focus. The rectangular mask which appears

in the finder is in focus at the same time as the sub-

ject so that a sharp definition of the field that is being

photographed can be seen.

The field outside the mask is also visible, so that

action outside the field being photographed can be

observed and the camera moved to include it if

desirable. '

When other lenses are used, a viewfinder lens

which matches the focal length of the taking lens

must be used. The table on page 17 shows the finder

lenses which are available. To remove the finder lens,

unscrew the retaining collar and lift out the lens.

When replacing a finder lens, insert the lens into the

lens retaining mount so that the stud on the lens

mount fits in the slot in the lens tube; then tighten

the retaining collar.

correction for close-ups

Because the finder and the taking lens are separated,

they do not always cover the same area and slight

compensations are necessary when filming subjects

very near the camera. To simplify framing for close-

ups, three crosses have been placed within the finder

REFERENCE CROSS

2'12

FT. TO 7 FT.

REFERENCE CROSS

1'12

FT. TO 2% FT.

16

"

lenses

J;

\!

~

Kodak Cine Ektar Lenses, 15mm

1/2.5,

25mm

1/1.4,

25mm

1/1.9,

102mm

1/2.7,

and 152mm

1/4.0

in

type C mounts fit directly on this camera. A Kodak

Ektar

1/1.4

Converter, 25mm to 15mm, used with a

converter adapter, is available to fit the 25mm

1/1.4

lens with a type C mount. The Kodak Cine Ektar

Lens, 25mm

1/1.4,

with the converter in place, be-

comes a fast, wide-angle lens which covers a field

approximately 60% larger than a 25mm lens. This

reduction in focal length is accomplished without

loss of lens speed or of image quality.

By using a Kodak Cine Lens Adapter Type C the

following interchangeable Kodak Cine

Ektar

Lenses

can be used: a 15mm

1/2.5

wide-angle lens, a 40mm

1/1.6,

a 63mm

1/2.0,

a 102mm

1/2.7,

and a 152mm

1/4.0.

Viewfinder lenses are available for use with

15, 40, 50, 63, 75, 102, and 152mm focal length lenses.

For wider coverage than can be obtained with the

standard 25mm lens, use a 15mm wide-angle lens. The

wide-angle lens covers a larger field, about 60% more

than the 25mm lens. For large, clear pictures at long

range-close-ups of sports, wild life, children at play

-use a telephoto or long-focus lens.

Taking the image produced by a 25mm lens as

normal, the other lenses produce images- magnified

in direct ratio to their focal lengths. Thus the 63mm

lens produces an image 27'2 times larger than a

25mm lens; with the 152mm lens the image will be

6 times larger.

IMPORTANT: For best results when using a long-locus

or telephoto lens, brace the camera against a firm

support. Use a tripod. whenever possible.

These pictures are actual enlargements from a Cine-Kodak film of the

same subject photographed from the same distance with five different

Cine-Kodak lenses: A is 25mm; B is 40mm; C is 63mm; D is l02mm;

and E is 152mm.

13

camera speed

For normal screen action with silent pictures, set the

camera speed at 16 frames per second.

If sound is to be dubbed in, or if you expect to run

the film at sound speed, the camera should be oper-

ated at 24 frames per second. When setting the

camera speed, remember that any camera speed

faster

than projection speed will produce slower-

than-normal action in the projected picture.

The speed dial can be turned until anyone of five

speeds (16, 24, 32, 48, or 64 frames per second) is

opposite the index mark. Intermediate speeds can be

obtained by turning the dial until the index mark is

between any two numbers.

using the turret

The turret rotates on a central axis, and, when

turned, brings each lens successively into picture-

taking position. To make certain that each lens is

correctly positioned, the turret snaps into place for

each lens.

With the turret snapped in place, the taking lens is

at the upper right and lined up with the film plane

mark on the camera cover. The viewfinder lens for

that particular taking lens is at the top of the turret.

If a 15mm lens and 152mm lens are used on the

turret, the 152mm lens must be in the lower position

when the 15mm lens is in the picture-taking position.

To avoid disturbing the lens settings when rotat-

ing the turret, grasp the two adjacent viewfinder

12 lenses.

field of view.

The heavy, upper right cross is the ref-

erence cross.

For correction when filming a subject 2V2to 7 feet

from the camera, with the 25mm lens, note the posi-

tion of the reference cross with respect to some point

on the subject. Then move the camera so that the

middle cross is at the position previously occupied by

the reference cross. The camera is now in position to

photograph the field previously outlined by the mask.

For correction at 1V2 to 2% feet, with the 25mm

lens, use the lower cross instead of the middle cross.

For other lenses the crosses are to be used for dif-

ferent subject distances. See the table below.

Viewfinder Lenses 15mm

I

25-40-50mml 63-75mm 1102-152mm

When Film-to-Sub.iect Distance is

Use Lower Cross 1 Foot to 1% Feet to 2% Feet to 3V2Feet to

11/2Feet 2% Feet 4 Feet 6 Feet

Use Middle Cross 1V2Feet to 2% Feet to 4 Feet to 6 Feet to

4Y2Feet 7 Feet

9

Feet 12% Feet

sighting

Hold the camera as shown in the illustration. Brace

the elbows against the side of the body to steady the

camera. The Cine-Kodak K-100 Cameras can be hand-

held. However, the pictures, when projected on the

screen, will appear much steadier if the camera is

placed on a tripod while pictures are being taken.

The tripod socket is on the bottom of the camera.

17

making exposures

With the spring motor fully wound, about 40 feet of

film can be exposed. If several consecutive scenes

must be photographed, be sure to wind the spring

when the spring motor dial indicates that the motor

will run about 5 to 10 feet of film. However, it is

best to wind the spring after each scene. In this way

the camera is always ready for use.

To start the motor, push the exposure lever down-

ward. To stop, release the lever. Pressing the lever

all the way down locks it in the running position.

11

scene length

About 6 feet of film (15 seconds at 16 frames per

second) is sufficient for average scenes in which the

action is continuous. However, the length of a scene

should be governed by the nature of the subject.

Landscape shots, for example, can be of greater

duration than scenes with brief, fast-moving action.

shutter speeds

The exposure data is given on the basis of 16 frames

per second. The use of any faster speed requires a

larger lens opening (stop); for example, at 32 frames

per second, the lens opening should be 1 stop larger;

at 64 frames per second, the lens opening should be

2 stops larger. The Cine-Kodak Universal Guide

shows the proper lens opening for each camera speed.

Exposure Time in Seconds

Single Frame 1/20

EXPOSURE TIME

PE~

FRAME

Angle of Opening

in Shutter 165

0

16 Frames per Second 1/35

24 Frames per Second 1/50

32 Frames per Second 1170

48 Frames per Second

1/100

64 Frames per Second

1/140

10

NOTE:

It is extremely important that the film

perforations be engaged by the pulldown.

Check again to see if the film is properly lo-

cated in the film channel and follows the red

lines so that correct loops, which are also

important to the functioning of the camera,

are formed. Then inspect the pressure plate to

be sure

it

is seated correctly with respect to

the film and the film channel.

Follow the red film-guide lines and pass the film

between the

LOWER FILM GUIDE

and the film sprocket.

Engage the sprocket teeth in the film perforations.

Insert the end of the film in the slot in an empty

take-up spool. Turn the spool one turn to securely at-

tach the film to the spool. Place the spool, square hole

down, on the take-up spindle. Turn the take-up spool

clockwise with your finger until the film appears

snug on the spool.

Press down the exposure lever for a moment and

check the following conditions:

1

The spools must be seated all the way

down on the spindles.

2

The film must move evenly and must

follow the film-guide lines.

film meter

Set the film meter at

LOAD.

Then replace the cover

and turn the locking knob clockwise to

LOCKED,

to se-

cure the cover. Run the camera until the film meter

is at 100.

unloading and care of exposed film

pictures outdoors at night

......-

~

The usable length of film has been exposed when the

film meter shows O. Before removing the camera

cover, run off the trailer as follows:

Run the camera until the line below 0 on the film

meter is opposite the pointer. The end of the film can

usually be

heard

as it leaves the film channel. Remove

the cover; then remove the full spool of exposed film

from the take-up spindle. For best results have the

film processed as soon as possible after it is exposed.

See the directions that accompany your film.

Before rethreading, make sure the gate is free of

dirt, pieces of film, or foreign particles.

Unusual and artistic effects in color or black-and-

white can be obtained at night with your camera.

Brilliantly lighted streets or the theater districts of

large cities make interesting shots. Lighted streets

and squares photographed on wet nights or after a

heavy snow are especially attractive. Animated elec-

tric signs are always good subjects. For best results,

photograph only brightly illuminated scenes.

Use Cine-Kodak Tri-X Reversal or Cine-Kodak

Tri-X Negative Film for sporting events on dull

days, indoor-lighted events, and night-lighted out-

door events.

animation

by

single-frame exposures

One of the most absorbing fields made possible by

your camera is animation-the movie method of

breathing life into inanimate objects. You may wish

to try the simpler type where chessmen play their

own game, and books, ash trays, etc., roam around

over a table top. Or you may be sufficiently fascinated

by the almost limitless possibilities of animation to

try your hand at the more complicated types.

To animate a subject, expose a single frame, move

the subject slightly, expose another frame, move the

subject again, and so on. If a

certain

movement is

to take place in one second on the screen with the

projector operated at normal (16) speed, 16 single-

frame exposures will be required.

Applications of animation include: animated

titles, graphs that draw themselves, machines, and

other manufactured products that assemble them-

selves.

The Cine-Kodak K-100 Cameras are also excel-

lent for time-lapse photography-a method of greatly

accelerating a period of time. The growth of a flower

to full bloom, rapid movement of street traffic, cloud

formations for an entire day, can all be depicted in

a few seconds' time with time-lapse photography.

Expose one frame at a time at intervals which will

produce the desired effects. The interval between

exposures will vary according to subject matter.

To make single-frame exposures, set the speed dial

at 16 frames per second and push

up

the exposure

lever once for each exposure. Each single frame is

exposed for 1/20 of a second. If the Universal Guide

is used for determining the exposure, one stop small-

er than the exposure indicated for 16 frames per sec-

ond should be used; for example, if the exposure

guide reading is

f

/5.6 for 16 frames per second, the

lens opening should be set at

f/8.

20

and metal can. Remove the paper band around the

film. Save the paper band, carton and metal can to

send the film to your dealer for processing.

Pull out about two feet of film, Be especially careful

not to let too much film unwind or the film on the spool

will be fogged. Place the spool of film on the

SUPPLY

SPINDLE

with the square hole down. Make sure that the

spool is properly seated-the end of the supply spindle

should project through the round hole in the spool.

Following the red film-guide lines and arrows, in-

sert the film between the

UPPER FILM GUIDE

and the

FILM SPROCKET.

Push the film down and at the same

time pull it forward to engage the sprocket teeth in

the film perforations. Open the

PRESSURE PLATE

only

enough to make it stay open. Do not push it beyond

this open position. (The illustration below shows the

pressure plate fully opened in order to show the pull-

down.)

Following the film-guide lines, pass the film

between the pressure plate and the

APERTURE PLATE.

Be sure the film is placed all the way into the film

channel.

Close the pressure plate and move the film back and

forth until the

PULLDOWN

engages a film perforation

9

.•

complete instructions

cleaning the lenses

The glass-air surfaces of the lens on your camera.have

been Lumenized to reduce internal reflections, flare,

and scattered light. This increases the brilliance of

black-and-white pictures and the color purity of

Kodachrome pictures. All Lumenized lenses appear

tinted by reflected light but this color has no effect

on the image.

To clean the lens, carefully brush off any dust or

grit with wadded Kodak Lens Cleaning Paper or a

fine camel's-hair brush. If necessary, wipe the sur-

faces gently with a wad of lens cleaning paper or a

clean, soft, lint-free cloth. Always wipe with a circu-

lar motion. Fingerprints, oil spots, or other scum

deposits can be removed with a drop of Kodak Lens

Cleaner on the cloth. DO NOT USE ALCOHOL.

winding motor

Be sure the

EXPOSURE LEVER

is in the off or horizontal

position. Raise the

WINDING HANDLE

on the side of

the camera and fit the opening in the handle over the

square end of the shaft. Turn the winding handle

clockwise until the

SPRING MOTOR DIAL

is at about 40

feet.

loading

Turn the locking knob counterclockwise to the

UN-·

LOCKED

position and lift off the cover.

Take the empty take-up spool out of the camera.

Remove a spool of Cine-Kodak film from its carton

cleaning the film channel

Open the pressure plate as far as it

will go. With the ball of the thumb,

rub off any accumulation of dirt on

the polished tracks of the plate.

With a match covered with a clean

cloth that has been dipped in Stod-

dard's Solvent, such as Sovasol No.

5 (Socony-Vacuum Oil Company) or

Sunoco Spirits (Sun Oil Company),

remove any accumulation on the

tracks of the aperture plate. (Do not

use alcohol as a cleaning agent.) Re-

move any dust or lint on the edges

of the rectangular aperture. Be ex-

tremely careful not to scratch the

polished surfaces over which the

film travels. Never scrape the tracks

with a metallic tool.

21

8

Cine-Ko ak

ilrns

All16rn11~ films perforaied. one

or two edges can be used.

Kodachrome Film

Kodachrome Film, Daylight Type reproduces colors with

startling realism when exposed under daylight con-

ditions.

Kodachrome Film, Type A is color-balanced for photo-

graphic flood lamps and requires no filter when so

used. The film can also be used for taking pictures

in daylight with a filter such as the Kodak Daylight

Filter for Kodak Type

A

Color Films (see page 25).

Processing-Exposed Kodachrome Film may be taken

to a dealer who will arrange for processing at a labo-

ratory of your choice. If you prefer, you may mail it

to a Kodak Laboratory using a Kodak Processing

Mailing Label or to any other laboratory processing

Kodachrome Film. The mailing labels may be ob-

tained from your dealer, and film sent in with these

labels will be returned to the same dealer. Payment

will be made to your dealer who can also order full-

color duplicates of your Kodachrome Films.

Cine-Kodak Black-and-White Reversal Films

These films are sold at a price which does not include

processing by the Eastman Kodak Company. They

are intended for processing by independent commer-

ciallaboratories or by the user. Conventional reversal

processing provides a positive image for projection.

Duplicate prints can also be obtained from many

commercial laboratories.

Plus-XReversal is a very fine-grain film used in general

black-and-white picture making. It can be used with

natural or artificial illumination.

22

T

complete operating

winding motor

•

8

loading

•

8

camera speed

•

12

using the turret

•

12

lenses

•

13

focus 14

setting the lens opening 14

the viewfinder 1S

correction for close-ups 16

sighting 17

making exposures 18

shutter speeds 18

scene length 18

unloading and care of exposed film 19

pictures outdoors at night 19

animation by single-frame exposures 20

cine-kodak films 22

cine aids 24

focus the viewfinder

Hold the camera as shown and focus the sub-

ject in the finder by turning the finder focus

knob back and forth until the image is sharp.

frame and shoot

Frame the picture within the finder rectan-

gular mask and push the exposure lever

downward to start taking pictures.

Tri-X Reversal

is a very fast black-and-white film par-

ticularly suitable for commercial, television, indus-

trial, and athletic photography where adverse light-

ing conditions are frequently encountered.

Cine-Kodak Negative Films

Plus-X

Tri-X

The use of these black-and-white films results in a

negative from which positive projection prints can

be obtained. They are intended for processing by

independent commercial laboratories or by the user.

magnetic sound track for 16mm film

Kodak Sonotrack Coating-a

magnetic sound track coat-

ing service-is now available for processed, single-

or double-perforated Kodachrome or black-and-white

I6mm Cine-Kodak film.

Sonotrack Coating can be applied to film taken at

either sound or silent speed. It is placed on the side

of the film that faces the projection lamp.

Kodak Sonotrack Coating is available in three

widths. Single-perforated I6mm film having no

sound track will be Sonotrack coated the full width

of the track area. When an optical sound track is on

the film, it will be Sonotrack coated half the width of

the optical track, unless you specify that the full

width of the optical track be coated. It is available in

edge-coating for double-perforated I6mm film.

Sonotrack Coating must be ordered through

your Kodak dealer. This coating can be or-

dered by your dealer after your 16mm Cine-

Kodak film has been processed. Unexposed

film will not be coated.

23

cine aids

r

combination lens attachments

O·

~

,

Kodak

Adapter Ring

Kodak

Portra Lens

Kodak

Wratten Filter

Kodak

Lens Hood

set the focus

Turn the front collar of the lens barrel until

the figure corresponding to the distance

from the camera to the subject is at the

index.

The Kodak Combination Lens Attachments permit

the use of any desired combination of Kodak Portra

Lens, Kodak Pola-Screen, and Kodak Wratten Filter.

See table below for attachment series number and

adapter ring number for the various lenses.

Kodak Adapter Rings screw into the lens barrel.

The Kodak Retaining Ring is unscrewed from the

Adapter Ring to admit a filter or Portra Lens. The

retaining ring is then screwed back into place.

To use a filter and a Portra Lens at the same time,

obtain another Kodak Retaining Ring. The Portra

Lens must always be nearer the camera lens.

set the lens opening

Turn the collar of the lens barrel until the

proper lens opening is at the index. The lens

in the illustration is set for

1/8

and 15 feet.

Attachment

JI

Lens Series Adapter Ring

n

Number Number

~

1

15mm,

1/2.5

6 28

(SCREW-IN)

I

(WIDE-ANGLE)

I

Kodak Cine Ektar Lenses

25mm,

1/1.9

5 22

(SCREW-IN)

("C" Mount)

25mm,

1/1.4

6 26

(SCREW-IN)

102mm,

f

/2.7

6

NONE REQUIRED

152mm,

f

/4.0

6

NONE REQUIRED

15mm,

1/2.5

6 28

(SCREW-IN)

(WIDE-ANGLE)

25mm,

1/1.9

6 27

(SCREW-IN)

Kodak Cine Ektar

25mm,

1/1.4

6 27

(SCREW-IN)

Interchangeable Lenses ,

40mm,

1/1.6

6 27

(SCREW-IN)

("5" Mount)

63mm,

1/2.0

6

NONE REQUIRED

102mm,

1/2.7

6

NONE REQUIRED

152mm,

1/4.0

6

NONE REQUIRED

I

set the speed dial

The speed dial can be turned until anyone of

five speeds (16, 24, 32, 48, or 64 frames per

second) is opposite the index mark.

For normal screen action, when using a si-

lent projector, use the 16 frames per second

speed. Film to be run at sound speed should

be exposed at 24 frames per second.

select the lens

Select the desired taking lens and corre-

sponding viewfinder lens. Rotate the turret

until these lenses are in the proper picture-

taking position.

select the lens opening

Slide the card supplied with each roll of

Kodak film into the Cine-Kodak Universal

Guide on the side of the camera. One side of

the card is for movie making outdoors-the

other side is for use indoors with photo-

graphic flood lamps.

Turn the dial on the guide so that the se-

lected camera speed is opposite the proper

light condition; then use the lens opening

indicated.

4

KODACHROME filM

Oaylight Type

Filters are used in black-and-white photography to

obtain correct tone rendering, to create special sky

and moonlight effects, to cut haze, and to obtain con-

trast between areas differing in color. The wise use

of a filter will often make the difference between ex-

cellent photography and mere record.

Correction filters aid in reproducing colors as

grays in the relative brightness that the eye sees

them. Oftentimes blue reproduces too light without

a filter, and there is no contrast between sky and

clouds. Filters also cut bluish atmospheric haze on

distant scenes.

A filter such as the Kodak ND-3 Filter is needed

when Cine-Kodak Tri-X Film is used in sunlight.

Filters such as the K2, G, A, and Xl are recom-

mended for black-and-white photography. All are

supplied as Kodak Combination Lens Attachments in

series sizes. Additional information on filters comes

with your film.

Cine-Kodak Filters

;

WITH FILTER

Kodachrome Filters

A filter such as the Kodak Skylight Filter

is recommended

for Kodachrome Film Daylight Type, for pictures in

open shade under a clear blue sky, pictures made on

overcast or hazy days, distant scenes (mountain or

marine views), sunlit snow scenes, and aerial photo-

graphs.

A filter such as the Kodak Photoflood Filter No. 80B (for

Kodak Daylight Type CoJor Films)

can be used if regular

daylight Kodachrome is to be exposed indoors with

photographic flood lamp illumination. Type 'A film is

preferred for photographic flood lamp illumination.

A filter such as the Kodak Daylight Filter for Kodak Type A

Color Films

is recommended if Kodachrome Film Type

A is to be exposed outdoors in daylight. Exposures

with this filter are the same as those for Kodachrome

Film Daylight Type.

25

hand crank

The Cine-Kodak K-IOOCamera can be hand-cranked

either forward or reverse for special effects. No more

than two feet of film should be reverse wound at a

time. This is accomplished by use of the Cine-Kodak

K-IOOHand Crank. See your Cine-Kodak dealer.

electric motor drive

The camera is adaptable to electric motor drive by

using the Cine-Kodak K-IOOMotor Drive Shaft avail-

able from your Cine-Kodak dealer.

field case

A fine instrument deserves good care, and there is no

better way of caring for your camera than to keep it

in a suitable case. Not only will its appearance be

benefited, but the camera will actually take better

pictures longer, if it is properly cared for. The field

case not only protects the camera from scuff-marks

and bangs, but permits it to be ready for picture tak-

ing at a moment's notice. The case will also help keep

your camera clean; dust collecting on the lens sur-

face requires frequent brushing off to maintain pic-

ture clarity, snap, and brilliance.

26

1"

I

3

2

load the camera

Remove the empty take-up spool. Unroll

about two feet

01

film from the. new spool

and place the spool of film on the

SUPPLY

SPINDLE,

square hole down.

Follow the film path as shown by the red

lines and arrows on the plate. Push the film

down and, at the same time, pull it forward

to engage the

FILM SPROCKET

teeth in the

film perforations. The take-up spool turns in

the direction of the arrow shown on the

camera.

Press down the

EXPOSURE LEVER

for a

moment and check the following:

1

The spools must be seated all

the way down on the spindles.

Check to see that

.the

film

2

moves evenly and follows the

film-guide lines.

CAUTION: It

is

possible to run film through

the camera without taking satisfactory pic-

tU1"eS,if the film perforations are not engaged

by the PULLDOWN. This is because the driv-

ing force then comes irom the sprocket only.

Set the

FILM METER

at

LOAD.

Then replace

the cover and turn the locking knob clockwise

to secure the cover. Run the camera until the

film meter is at 100.

,II

.It

I,·'

i

Kodascope Proiectors

The Kodascope projectors answer all your needs for

sound or silent motion pictures. The projectors come

equipped with powerful 750-watt lamps amply bright

for average projection. A 1000-watt lamp can be used

for large audiences. The projectors are fitted with a

2-inch

f

/1.6 Lumenized Kodak Projection Ektanon

Lens. The following Kodak Projection Ektanon

Lenses are also available: a 1Yz-inch

f

/2.0, a 3-inch

f

/2.0, and a 4-inch

f/2.5.

The Kodascope projectors are smartly styled, light,

compact, and easy to operate. All are permanently

lubricated.

The Kodascope Royal Projector,

illustrated above, is de-

signed to give the best in silent movie projection. It

operates on ac or

de,

105 to 125 volts, both forward

and in reverse, and has a speed control knob for rapid

rewind.

27

The Kodascope Pageant Sound Projector,

ac or de, 105

to 125 volts, has a capacity of 2000 feet of film. It

operates at both sound and silent speeds. An acces-

sory microphone plugged into the amplifier enables

you to narrate your silent movies and to use the

Pageant as a public address system.

The Kodascope Analyst Projector,

60-cycle ac only, can

project movies in normal fashion on a screen and also

in natural light on its own built-in screen. It also

operates by a remote control switch which provides

immediate

forward or reverse operation. It is ideally

suited for such special applications as sports analysis,

motion study, etc.

Kodak Cine Photoguide

Take the guesswork out of movie making with the

Kodak Cine Photo guide. Here is a 32-page pocket-

sized booklet with a durable leather-like cover. It con-

tains on-the-spot movie-making information for both

common and unusual lighting conditions. Among the

subjects covered by convenient dial computers, tables,

and brief text are: indoor and outdoor exposure,

close-up photography, movie continuity, field size and

depth-of-field tables for many Kodak Cine Lenses and

supplementary lenses, and film and filter data. See

your Kodak dealer.

28

CINE-KODAK

K-100

CAMERAS

• This instruction manual is for the Cine-

Kodak K-I00 Camera and the Turret Model.

On the turret model you can mount three

picture-taking lenses with matching view-

finder lenses - thus allowing you to change

quickly from wide-angle to medium to tele-

photo shots. The Cine-Kodak ~-100 Camera

has a single taking lens and viewfinder lens.

Any of the lenses, Ifimm to I52mm with C

mounts, can be used. The cameras use either

single- or double-perforated Ifimm film.

Movies are more than just pictures. Mere-

ly following the rules for proper camera op-

eration will produce technically acceptable

pictures. Add to this imagination and artis-

tic effort and your pictures become good

movies - movies that you will be proud to

show and that your friends will really enjoy

seeing.

Simple instructions are given on the next

6 pages. For more detailed information, read

further in the manual.

wind the motor

Turn the

WINDING HANDLE

clockwise until

the

SPRING MOTOR DIAL

is at about 40 feet.

remove the cover

Turn the locking knob counterclockwise

and lift off the cover.

Before making any important pictures, it

is always well to shoot a roll of film. This

will give you practice in camera operation

and provide a check on your results. If you

have any questions, your dealer will be glad

to help.

T. M. REG. U. S. PAT. OFF.

p

"

Serial Numbers: The serial number of your camera is

stamped on the rear carry handle clip. The serial number

of the lens is stamped on the front of the lens barrel.

Record these numbers with your personal papers for posi-

tive identification of the camera and lens. In case of loss

or theft, report the fact to your Kodak dealer and to the

local police at once.

EASTMAN KODAK COMPANY

1-57

•

ROCHESTER 4, N. Y .

PRINTED IN THE UNITED STATES OF AMERiCA

~@@1ffifu

~ GUARANTEE ~

Within a year after purchase, any re-

pairs necessary to your Cine-Kodak

K-IOOCamera due to a defect in ma-

terials or workmanship will be made

or, at our option, the camera will be

replaced without charge. No other

warranty or guarantee, express or im-

plied, shall be applicable to this equip-

ment. Nor are we responsible for loss

of film, for other expenses or incon-

veniences, or for any consequential

damages occasioned by the equipment.

In case of a defect, the camera

should be sent directly or through a

Kodak dealer to Eastman Kodak Com-

pany or a repair firm authorized by us

to make such repairs. It should be ac-

companied by a description of the

trouble encountered and other avail-

able information regarding the cam-

era, including the date and place of

purchase.

~t::::la@@