Kontron Embedded Technology REVOLUTION-V5 Notebook PC W/ 802.11 b/g WLAN and Bluetooth Radio User Manual plus UserMan

Kontron Embedded Technology Inc Notebook PC W/ 802.11 b/g WLAN and Bluetooth Radio plus UserMan

User Manual

Download: Kontron Embedded Technology REVOLUTION-V5 Notebook PC W/ 802.11 b/g WLAN and Bluetooth Radio User Manual plus UserMan
Mirror Download [FCC.gov]Kontron Embedded Technology REVOLUTION-V5 Notebook PC W/ 802.11 b/g WLAN and Bluetooth Radio User Manual plus UserMan
Document ID520595
Application ID6JE/j8Pj2ZAzSp1R8HZEKw==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize316.47kB (3955884 bits)
Date Submitted2005-03-04 00:00:00
Date Available2005-03-04 00:00:00
Creation Date2005-02-18 18:50:29
Producing SoftwareAcrobat Distiller 5.0 (Windows)
Document Lastmod2005-02-18 18:50:29
Document Titleplus UserMan.pdf
Document CreatorPScript5.dll Version 5.2
Document Author: amanda

User Manual
NOTEBOOK PC
KONTRON / Revolution plus
Version 1.00
Part Number:
Contents
Contents ..........................................................................................................................................................i
Dear Valued Customer,................................................................................................................................... iv
Technical Alteration Disclaimer ........................................................................................................................v
Copyright Notice...............................................................................................................................................v
Symbols used in this Manual .......................................................................................................................... vi
Introduction to User Manual ...........................................................................................1
Safety Instructions.........................................................................................................................................2
Operation of Laser Source Devices .................................................................................................................2
Safety Instructions for the CMOS Lithium Battery ............................................................................................3
Safety Instructions for the Removable Lithium Battery Modules ......................................................................3
Care and Maintenance ...................................................................................................................................5
Display .............................................................................................................................................................5
Other Areas......................................................................................................................................................5
Base Unit and Optional Parts........................................................................................................................6
Base Units........................................................................................................................................................6
Optional Parts ..................................................................................................................................................6
The ReVolution Convertible Laptop and Tablet ..........................................................................................8
ReVolution at a Glance ....................................................................................................................................9
Front Panel ..................................................................................................................................................9
Bottom Panel ...............................................................................................................................................9
Front Panel – LEDs ...................................................................................................................................10
Front Laptop View .....................................................................................................................................10
Front Laptop View (continued)...................................................................................................................11
Interface Panel ..........................................................................................................................................11
Interface Panel – Right Side ......................................................................................................................12
Interface Panel - Left Side .........................................................................................................................12
I/O Extension Stick (Port Replicator) .........................................................................................................13
Cabled I/O Extension.................................................................................................................................14
In-Vehicle Mount........................................................................................................................................14
Getting Started .............................................................................................................................................16
Connecting to Power......................................................................................................................................16
Connecting the AC/DC Adapter.................................................................................................................17
Power On/Off Button .................................................................................................................................17
Power On and Power Off ...............................................................................................................................18
Turning on the System ..............................................................................................................................18
Turning off the System ..............................................................................................................................20
Battery Power.................................................................................................................................................20
Converting from Laptop to Tablet and Back...................................................................................................21
Open to Laptop Position ............................................................................................................................21
Convert from Laptop to Tablet ...................................................................................................................21
Convert from Tablet to Laptop ...................................................................................................................21
Close from Laptop Position........................................................................................................................22
Windows Set-up .............................................................................................................................................22
Accessing the User Manual ...........................................................................................................................22
Modifying the System ..................................................................................................................................24
Alternative Display .........................................................................................................................................24
Battery Packs.................................................................................................................................................25
Removing Battery from Right Bay .............................................................................................................25
Inserting Battery into Right Bay .................................................................................................................26
Hard Disk Drive - Master................................................................................................................................27
ReVolution User Manual 1.00
02/18/05
Removing a Hard Disk Drive (HDD) ..........................................................................................................27
Inserting a Hard Disk Drive (HDD).............................................................................................................28
Left Bay Modules ...........................................................................................................................................29
CD-ROM, CD-RW, DVD and DVD/CD-RW Modules .....................................................................................29
Removing any Left Bay Module.................................................................................................................30
Inserting any Left Bay Module ...................................................................................................................30
PCMCIA Cards...............................................................................................................................................31
Shoulder Straps .............................................................................................................................................32
Audio..............................................................................................................................................................33
Volume Level.............................................................................................................................................33
CD-ROM, CD-RW, DVD and DVD/CD-RW Combo Module Drives ...............................................................33
Software Installation- CD writer .................................................................................................................33
Software Installation - DVD player .............................................................................................................33
Chipset...........................................................................................................................................................34
Driver Installation: Chipset.........................................................................................................................34
Driver Installation: Application Accelerator ................................................................................................34
LAN - Embedded............................................................................................................................................34
Modem ...........................................................................................................................................................34
Power Management Modes ...........................................................................................................................35
Windows ....................................................................................................................................................35
Battery Operations.....................................................................................................................................36
Touchscreen ..................................................................................................................................................37
User Settings .............................................................................................................................................37
Driver Installation .......................................................................................................................................37
Calibrate ....................................................................................................................................................38
Touch Pad......................................................................................................................................................39
Touch Pad Basics:.....................................................................................................................................39
USB Ports ......................................................................................................................................................40
Driver Installation .......................................................................................................................................40
Video..............................................................................................................................................................41
Driver Installation .......................................................................................................................................42
Video Rotation ...........................................................................................................................................43
Wireless - 802.11b/g (WLAN) ...........................................................................................................................44
Driver .........................................................................................................................................................44
Wireless - Bluetooth .......................................................................................................................................46
Technical Data..............................................................................................................................................47
ReVolution .....................................................................................................................................................47
Main Specification .....................................................................................................................................47
Mechanical Specification ...........................................................................................................................48
Environmental Specifications.....................................................................................................................48
CE-Directives and Standards ....................................................................................................................49
CD-ROM Module............................................................................................................................................50
CD-RW Module ..............................................................................................................................................50
DVD Module...................................................................................................................................................50
DVD/CD-RW Module .....................................................................................................................................50
Floppy Disk Drive Module ..............................................................................................................................51
Lithium Ion Battery Pack ................................................................................................................................51
Technical Appendices .................................................................................................................................52
RS232 Serial Port (COM A) ...........................................................................................................................52
Parallel Port (I/O Stick Option Only)...............................................................................................................52
Analog Monitor (VGA-Output, I/O Stick Option Only).....................................................................................53
USB 2.0 Ports ................................................................................................................................................53
Power Supply Connector ...............................................................................................................................53
PS/2 Keyboard/Mouse Connector (I/O Stick Option Only) .............................................................................54
RJ-11 Modem Port .........................................................................................................................................54
ii
02/18/05
ReVolution User Manual 1.00
RJ-45 LAN Port ..............................................................................................................................................54
Line-In ............................................................................................................................................................55
MIC-In ............................................................................................................................................................55
Speakers........................................................................................................................................................55
System Hardware Assignments .....................................................................................................................56
Table of IRQ Assignment by BIOS ............................................................................................................56
DMA Channel Table ..................................................................................................................................56
Embedded Controller...................................................................................................................................57
Embedded Controller LEDs ...........................................................................................................................57
Power and Battery Indicators .........................................................................................................................57
Phoenix BIOS Setup ....................................................................................................................................58
Navigating the Setup Menus ..........................................................................................................................58
Legend Bar ....................................................................................................................................................58
Field Help Window .........................................................................................................................................59
General Help Window ....................................................................................................................................59
Advanced Hard Disk Features...................................................................................................................59
Memory Cache...............................................................................................................................................61
Boot Features Menu.......................................................................................................................................61
Advanced Menu .............................................................................................................................................62
OEM Platform Advanced Memory Menu ...................................................................................................62
Integrated Device Control Sub-Menu ........................................................................................................63
Advanced Chipset Control Menu ...............................................................................................................63
I/O Device Configuration Menu ......................................................................................................................64
Keyboard Features.........................................................................................................................................65
Security Menu ................................................................................................................................................65
Boot Menu......................................................................................................................................................66
Exit Menu .......................................................................................................................................................66
Exit Saving Values.....................................................................................................................................66
Exit Discarding Changes ...........................................................................................................................66
Load Setup Defaults.......................................................................................................................................67
Discard Changes .......................................................................................................................................67
Save Changes ...........................................................................................................................................67
BIOS Messages .............................................................................................................................................68
Test Points and Beep Codes .........................................................................................................................71
Customer Service.........................................................................................................................................75
Technical Support ..........................................................................................................................................75
Returning Defective Merchandise ..................................................................................................................76
ReVolution User Manual 1.00
02/18/05
iii
Dear Valued Customer,
At Kontron Mobile Computing, we strive to be the worldwide leader in customer-specific computing
solutions for demanding environments. Our mission is to provide you with a total system solution for your
field automation needs.
The ReVolution convertible laptop/tablet is a computing platform designed for off-site and in-vehicle users
requiring remote, high-powered computing capabilities. The ReVolution expands to integrate multiple
technologies into one powerful solution specific to your application needs.
Kontron Mobile Computing has built its reputation around the endurance of its products in demanding
environments. The ReVolution meets strict standards for computing equipment in shock, vibration,
temperature, humidity and altitude testing. It withstands the toughest conditions and proves itself again
and again in mission-critical field applications.
When we deliver your new ReVolution, our job at Kontron Mobile Computing will have just begun. We will
do what it takes to ensure your complete satisfaction with our services and your ReVolution. We want this
to be the beginning of a long and outstanding experience for you, our valued customer.
Kontron Mobile Computing
7631 Anagram Drive
Eden Prairie, MN 55344-7310
iv
02/18/05
ReVolution User Manual 1.00
Technical Alteration Disclaimer
The information contained in this manual may be subject to technical alteration, as a result of the continual upgrading
of our products. The attached documentation does not guarantee the technical processes or product characteristics
described in the manual.
Kontron Mobile Computing does not accept any liability for printing errors or other inaccuracies in this manual. This
manual only contains a general description of technical processes and instructions that may not be applicable in
every case. If in doubt, please contact your nearest Kontron Mobile Computing representative or office listed in the
“Technical Support” section of this manual.
Copyright Notice
This manual is protected by copyright. All rights reserved by Kontron Mobile Computing Inc. Copies of all or part of
this manual or translations into different languages may only be made with the prior written consent of Kontron Mobile
Computing. This manual only reflects the technical status of the ReVolution product at the time of printing.
©2002 Kontron Mobile Computing Inc.
Printing and duplication, even of sections, is permissible only with the express approval of:
Kontron Mobile Computing
7631 Anagram Drive
Eden Prairie, MN 55344-7310
ReVolution User Manual 1.00
02/18/05
Symbols used in this Manual
Symbol
Meaning
This symbol indicates the danger of injury to the user or the risk
of damage to the product if the corresponding warning notices are
not observed. It may also cause interference with radio-sensitive
equipment.
This symbol indicates that the product or parts that may be
damaged if the corresponding warning notices are not observed.
This symbol indicates general information about the product and
the user manual.
This symbol precedes helpful hints and tips for daily use.
SYSM
Program names are printed in italics.
format a:
Commands are printed in Courier.
®
®
®
®
®
®
vi
Windows, Windows XP Professional, Windows 2000 Professional and Windows 98SE, MS-DOS, are
registered trademarks of the Microsoft Corporation.
IBM, PC-AT, OS/2 and PS/2 are registered trademarks of the International Business Machines Corporation.
Intel and Pentium are registered trademarks of Intel Corporation.
UNIX is a registered trademark and exclusively licensed from the X/Open Company Limited.
LINUX is a registered trademark and exclusively licensed by Linus Thorwald
Other product names cited in this manual may also be trademarks and are used here solely for identification
purposes.
Solaris is a registered trademark of Sun Microsystems, Inc.
02/18/05
ReVolution User Manual 1.00
Introduction to User Manual
The ReVolution User Manual provides information to assist in using your ReVolution computer in the most productive
manner for your organization. It includes safety instructions, care and maintenance advice, and photographs of the
ReVolution, specific components and accessories.
The manual also includes a “Getting Started” section for first-time operations, or as a refresher on starting up the
system. The “Modifying the System” section describes how to use and adjust the components and devices. Refer to
the “Technical Data” section for component specifications, and the “Technical Appendices” section for programming
information. The “Customer Service” section offers technical support contact information.
To obtain additional copies of this user manual, or to view it online:
1. Insert the ReVolution Utilities CD that came with the original shipment of your ReVolution computer. This contains
an electronic copy of the manual.
2. Go to www.kontronmobile.com. Select the following path: Technical Support ĺTechnical SearchĺManual
3. Call or write the Kontron Technical Support department to order additional hard copies. Contact information is
located on the Technical Support page.
ReVolution User Manual 1.00
02/18/05
Safety Instructions
Please read this section carefully and observe the following instructions – and those on the computer - for your own
safety and correct use of the ReVolution.
Kontron Mobile Computing built and tested the ReVolution computer in accordance with EN60950. In order to
maintain this condition and ensure safe operation, you must observe the instructions and warnings contained here
and elsewhere in this manual.
Do not operate the ReVolution in areas sensitive to radio
interference, such as airplanes and hospitals. There is no
means to shut off the Bluetooth and WLAN radios installed in the system.
T Operate the ReVolution in accordance with the instructions for use.
T Make sure electrical receptacles match the regulations in your area.
T Place cables, especially the power cable, out of traffic areas where people could trip over them.
T Do not put an AC power connection in sockets shared by a number of other power users.
T Do not use an extension cable.
T Plug the power cable into a nearby socket to prevent an accidental disconnection.
T Use only the cables supplied by Kontron.
T Do not place the ReVolution in the proximity of heat sources or in a damp location. Make sure it has adequate
ventilation.
T Connect to ReVolution interfaces: only devices and components that meet the requirements of a SELV circuit
(security low voltage output) in accordance with EN60950.
T Lock or screw down all plugs on the connection cables to the housing.
T You may not safely operate the ReVolution if:
–it has visible damage or
–it no longer functions.
Shut down the computer and secure it against unintentional operation.
T Any extensions to the computer must meet legal stipulations and the device specifications.
T Only authorized Kontron technical repair personnel may perform assembly, extensions, new settings, alterations
or repairs while under warranty.
T Only use original accessories approved by Kontron.
Operation of Laser Source Devices
Class 1 laser products typically contain a label similar to the following. Use caution when dealing with such
devices.
The CD-ROM, CD-RW, DVD, DVD/CD-RW Combo modules and others contain a light-emitting diode (classified in
accordance with IEC 825-1:1993: LASER CLASS 1) and must not be opened. When the cover is opened, invisible
laser radiation is emitted. Do not expose yourself to this radiation.
02/18/05
ReVolution User Manual 1.00
Safety Instructions for the CMOS Lithium Battery
The CPU board is equipped with an internal, rechargeable CMOS lithium battery. Please refer to the “Technical Data”
section for information about battery type.
T This battery is not user-replaceable.
T Kontron shall not assume any warranty obligation if any attempt is made to replace the battery by individuals
other than those at Kontron repair facilities.
T Please observe local regulations for the disposal of the battery and the disposal information of the batterymanufacturers.
Safety Instructions for the Removable Lithium Battery Modules
The ReVolution is equipped with a removable lithium battery. Please observe following instructions:
T Refer to the “Getting Started” and “Technical Data” sections for information about the battery type.
T Only use batteries supplied by Kontron.
T Kontron shall not assume any warranty obligation if a different battery, a different battery type or a different
power source is used.
T Please observe local regulations for the disposal of the battery and the disposal information of the batterymanufacturers.
FCC Statement
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement:
This Transmitter has been demonstrated co-location compliance requirements with (Bluetooth/ Model No: MB011SL).
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To
maintain compliance with FCC RF exposure compliance requirements, avoid direct contact to the transmitting
antenna during transmitting.
Any changes or modifications (including the antennas) made to this device that are not expressly approved by the
manufacturer may void the user’s authority to operate the equipment.
Canadian Notice
This digital apparatus does not exceed the Class B limits for radio noise for digital apparatus set out in the Radio
Interference Regulations of the Canadian Department of Communications.
European Union Notice
Warning: This is a Class B product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures to mitigate such interference.
ReVolution User Manual 1.00
02/18/05
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended
by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
ACHTUNG
Explosionsgefahr bei falsch eingesetzter Batterie. Batteriewechsel nur mit gleichen oder ähnlichen, vom Hersteller
empfohlenen, Batterien.
WARNING
Only authorized service personnel should attempt to repair this equipment. Improper repairs can create a safety
hazard.
WARNUNG
Lebensgefahr Achtung, nur autorisiertes Kundendienst Fachpersonal darf dieses Gerät reparieren. Falsche
Reparaturen können lebensgefährlich sein.
02/18/05
ReVolution User Manual 1.00
Care and Maintenance
Display
Use a soft cloth to clean the display. You can use a slightly dampened cloth if display is soiled but DO NOT use any
abrasive substances or materials on the display surface.
Other Areas
Clean all other areas of the ReVolution with a damp, soft cloth. You may dampen the cloth with a mild household
cleaner or simply water. If a mild household cleaner is used, wipe again with a damp cloth only and then with a dry
cloth.
x
Do not use strong solvents, such as benzene, thinner or
rubbing alcohol that could discolor paint or plastic.
x
Do not use commercial household cleaners or cosmetics,
as they may harm the surface.
x
Do not spray water, as liquid damages the computer or
causes it to work improperly.
x
TOUCH PAD: Avoid using sharp objects such as pen or
pencil tips because they can permanently damage the
touch pad’s surface. Use the stylus provided.
x
TOUCHSCREEN Avoid using sharp objects such as pen or
pencil tips because they can permanently damage the
touch pad’s surface. Use the stylus provided.
ReVolution User Manual 1.00
02/18/05
Base Unit and Optional Parts
This section displays the base unit and optional parts of the ReVolution laptop and tablet computer. Get in touch with
your Kontron sales representative for order information.
Base Units
Description
Convertible Laptop and Tablet Standard
Components:
x
x
x
x
x
x
x
x
Resistive Matrix Touchscreen
Master Hard Drive
CD-ROM Drive
Battery Pack
AC/DC Adapter
Power Cord
Stylus
Shoulder Strap
Optional Parts
Description
Master Removable Hard Drive Module –
40GB std; upgradeable to 60GB
CD-ROM Drive Module
CD-RW Drive Module
DVD Drive Module
DVD/CD-RW Combo Module
Floppy Disk Drive Module
Slave Removable Hard Drive Module –
40GB or 60GB
Backlit, Sealed Keyboard
02/18/05
ReVolution User Manual 1.00
Description
Battery Pack
External Battery Charger
I/O Extension Stick
(Port Replicator)
Hard Case
Soft Case
Shoulder Strap
In-Vehicle Mount with or without Docking
Station
Mount
AC Power Adapter
DC to DC Converter, 11-32 VDC
DC Power Cord with cigarette lighter plug,
12 ft.
ReVolution User Manual 1.00
02/18/05
The ReVolution Convertible Laptop and Tablet
Before using your ReVolution convertible laptop/tablet computer, please take a few minutes to learn about its features.
This section displays “at a glance” the components and options.
The ReVolution converts from a laptop to a tablet – and back! Switch-It™ is the unique hinge that turns the display
180 clockwise. The ReVolution consists of the following additional features:
x
x
x
x
x
x
x
x
x
x
x
x
QuickSilver 3™ CPU module with 1.6 GHz (or higher) Intel Mobile Pentium III-M processor
Rugged, lightweight, magnesium alloy construction tested to specific U.S. Military and NEMA standards for
resistance to shock, vibration, water, temperature and dust
40GB master removable hard drive (60GB upgrade)
512 MB DDR (upgradeable to 1GB)
CD-ROM drive module
Windows XP Professional, 2000 Professional and Windows 98SE operating system support
Bluetooth technology for wireless PAN connectivity
2 PCMCIA slots
Spread Spectrum wireless LAN connectivity
56Kb Modem (V.90)
Video RAM, 8-48MB (shared)
Wide range of optional components
Drive Options:
x
x
x
x
x
x
CD-ROM module
CD-RW module
40 GB or 60 GB slave removable hard drive
DVD module
DVD/CD-RW combo
Floppy Disk Drive module
You can configure the ReVolution for almost any application, through the user-friendly Phoenix BIOS setup, outlined
in the “Technical Appendices” section.
02/18/05
ReVolution User Manual 1.00
ReVolution at a Glance
Front Panel
Locking
Handles
Locking Display
Latch
Open Display
Latch
Left Bay
Left Bay
Latch
Right Bay
Stylus
Right Bay
Latch
Bottom Panel
Master Removable
Hard Disk Access
Slide Latch
Left Front Bay
Ejector Latch
Right Front Bay
Ejector Latch
ReVolution User Manual 1.00
02/18/05
Front Panel – LEDs
(1)
(2)
(3)
(4)
LED Indicators (L-R)
1) Hard Disk Drive Activity
2) LAN Activity
3) Future Use
4) Future Use
(1)
(2)
(3)
(4)
Stylus
LED Indicators (R-L)
1) Power
2) Battery Indicator
3) Caps Lock
4) Numeric Key Lock
Front Laptop View
Wireless
Antennas
Touchscreen
Display
Keyboard
Touch Pad
Mouse Buttons
10
02/18/05
ReVolution User Manual 1.00
Front Laptop View (continued)
Microphone
Brightness Control
button
Power On/Off
button
Stereo
Speaker
Stereo
Speaker
Interface Panel
The Interface Panel along the back spine of the ReVolution provides access to the ports and operating controls
described on the following page.
ReVolution User Manual 1.00
02/18/05
11
Interface Panel – Right Side
LAN Port
RJ-45
Modem Port
RJ-11
PCMCIA Card Slots
Interface Panel - Left Side
MIC-In
Line-In
Speakers
2 USB 2.0 Ports
Power Connector
COM 1
Docking Connector
12
02/18/05
ReVolution User Manual 1.00
I/O Extension Stick (Port Replicator)
The I/O Extension Stick fits into the docking connector on the back interface panel, and provides additional I/O ports
not standard on the back interface panel.
x
If PS2 or USB devices are attached to the I/O Extension
Stick, and the I/O Stick is “hotplugged” (the system is
running), these devices may fail to run. The system must
be rebooted. If these devices are plugged into the I/O Stick
after it is plugged into the system, they will operate
normally.
Docking
Connector
I/O Extension
Stick
2 USB 2.0 Ports
MIC In
P/S 2
Line In
Speakers
COM 1
VGA Output
Parallel Port
ReVolution User Manual 1.00
02/18/05
13
Cabled I/O Extension
In-Vehicle Mount
In-Vehicle Mount
Additional
Accessories
Other mounting solutions are also available. Contact your Kontron Mobile Computing sales representative for more
information.
14
02/18/05
ReVolution User Manual 1.00
This page was intentionally left blank.
ReVolution User Manual 1.00
02/18/05
15
Getting Started
This section describes first-time or typical start-up operations of the ReVolution system:
‰
‰
‰
‰
‰
‰
Connecting to Power
Power On and Power Off
Battery Power
Converting from Laptop to Tablet and Back
Windows End-User Experience
Accessing this ReVolution User Manual
Connecting to Power
The ReVolution is shipped in the “off” condition. Depending on your required range of use, you can connect the
ReVolution to AC (via an AC/DC adapter) or DC power supply.
This section will detail the proper cabling requirements for your ReVolution system.
16
x
Before using your system, become familiar with the
components and check that everything is connected
properly.
x
Following a proper cabling procedure will prevent a
false “power on” condition, which could result in unit
operational failure.
x
Attach the power cable last!
x
The plug on the AC power cable supplied corresponds
to the requirements of the country in which you
purchased your ReVolution system.
x
To avoid accidentally disconnecting your computer, plug
the AC power cable into a nearby outlet.
x
Allow at least 200 mm (approximately 8”) between the
ReVolution and the AC/DC adapter.
x
The AC/DC adapter must be uncovered and stand freely
with at least 100 mm (approximately 4”) free space
around it and the ReVolution.
x
Do not place the AC/DC adapter on a heat-sensitive
surface.
02/18/05
ReVolution User Manual 1.00
Connecting the AC/DC Adapter
When AC is available, connect the ReVolution to the AC power supply with an AC/DC adapter, as described below.
The AC voltage socket is on the left
side of the Interface panel.
Connect the locking DC power cord to the
DC voltage socket of the ReVolution.
The other end of the DC power cord
connects into available DC power connector
i.e. cigarette lighter.
Connect the female end of the AC power
cord into the AC power adapter.
Plug the male end of the AC power
adapter into an available wall socket.
Power On/Off Button
When pressed for ~1/2 second continuously, the system will:
x From Off: Check for valid temperature and then turn on.
x From Suspend: Check for valid temperature and then turn
on.
x From On: Initiate power off sequence.
When pressed for > 4 seconds continuously, the system:
begins an override function according to the ACPI specification.
The Override Function is useful if the system becomes
unresponsive. It will perform a “hard” shut down.
ReVolution User Manual 1.00
02/18/05
17
Power On and Power Off
The Power On/Off button is the lower of the two buttons located in the bottom-center of the display panel.
Power On/Off
button
Turning on the System
Do not operate the ReVolution in areas sensitive to radio
interference, such as airplanes and hospitals.
There is no means to shut off the Bluetooth and WLAN radios installed in the
system.
Press the Power On/Off button for approximately 1/2 second. The computer will check for valid temperature, then
turn on.
As the computer powers up, the LEDs will blink and the screen will indicate that the computer is installing BIOS and
checking memory. This is the Power-On Self Test (POST). When finished with POST, a System Configuration screen
shows briefly how the system BIOS is configured. To examine the configuration at length, press the Pause/Break key
as soon as the System Configuration comes up on the display. Press Enter to continue. The system then loads the
operating system.
The Power Indicator LED is the fourth light left of center. It is visible when the display is open or closed. The
following table lists the various power states as indicated by the combination of flashes of the Power and Battery
Indicator LEDs:
Power State
OFF
On, Charging
Low Battery
Running on battery
Running on AC not charging
Battery Malfunction
Sleep mode battery
Sleep mode AC
Power LED
OFF
ON
OFF
OFF
ON
Fast Blink
Slow Blink
OFF
Battery Indicator LED
OFF
Slow Blink
Fast Blink
ON
OFF
Fast Blink
OFF
Slow Blink
To awaken the ReVolution from sleep mode, press the Power button.
Slow blink is defined as - 0.5 Hz, 50% duty cycle, i.e. ON for one second, OFF for one second
Fast blink is defined as - 1 Hz, 50 % duty cycle, i.e. On for 500 ms, OFF for 500 ms
18
02/18/05
ReVolution User Manual 1.00
Never operate this computer in AC mode while standing in water.
You can operate it in DC or battery mode.
If you should encounter a problem in powering up:
1. Verify all connectors are properly connected.
2. Verify your boot drive.
3. Boot your system with only the power cord connected to the
computer. This is the minimum required to see if the system is
working.
4. If your system still does not start after steps 1-3, contact your
nearest Technical Support department for assistance. See the
“Technical Support” section of this manual for contact information.
ReVolution User Manual 1.00
02/18/05
19
Turning off the System
Kontron recommends that you close all applications before
shutting down or powering off the ReVolution.
1.
Follow the shut down procedures specified in the operating system manual provided with your unit.
OR
2.
Press the Power On/Off button and hold it down for approximately 1/2 second.
Battery Power
If an AC/DC power source is not available, you can operate your ReVolution from one or two battery packs.
The LED indicator for battery power is the third LED left of center.
Battery LED Indicator
A lithium ion battery pack is the only component that can be installed in the right front bay. It will provide
approximately 3.5 hours operating time under power management.
You can insert an additional lithium ion battery pack into the left front bay to extend your computer’s operating time.
Together, the two batteries will provide approximately 7 hours under power management. Refer to the “Modifying the
System” section for instructions on removing and inserting a battery pack, and power management information.
The Battery Indicator LED is the second light from the right, as displayed above. It is visible when the display is
open or closed. The following table lists the various power states as indicated by the combination of flashes of the
Battery and Power Indicator LEDs:
Power State
OFF
On, Charging
Low Battery
Running on battery
Running on AC not charging
Battery Malfunction
Sleep mode battery
Sleep mode AC
Power LED
OFF
ON
OFF
OFF
ON
Fast Blink
Slow Blink
OFF
Battery Indicator LED
OFF
Slow Blink
Fast Blink
ON
OFF
Fast Blink
OFF
Slow Blink
Slow blink is defined as - 0.5 Hz, 50% duty cycle, i.e. ON for one second, OFF for one second
Fast blink is defined as - 1 Hz, 50 % duty cycle, i.e. On for 500 ms, OFF for 500 ms
20
02/18/05
ReVolution User Manual 1.00
Converting from Laptop to Tablet and Back
Open to Laptop Position
1.
Pivot both locking handles out and down, to free the display.
2.
Press the open display latch while lifting the display.
3.
Lift the display to vertical position for laptop mode.
Convert from Laptop to Tablet
1.
Open the display to a vertical position as described above.
2.
Rotate the display in CLOCKWISE direction 180 until the display stop-peg clicks into the receiver on the
base chassis.
3.
Close the display, making sure it rests between the alignment guides on the nylon corner mounts.
4.
Press the locking display latch until it engages the latch catch.
5.
Pivot the locking handles up and in until they engage the locking tab on the display.
Convert from Tablet to Laptop
1.
Pivot both locking handles out and down, to free the display.
2.
Press the open display latch while lifting the display.
3.
Open the display to a vertical position.
4.
Rotate the display in counter-clockwise direction 180 until the display stop-clicks into the receiver on the base
chassis.
5.
Adjust screen to desired viewing angle.
ReVolution User Manual 1.00
02/18/05
21
Close from Laptop Position
1.
Pull display down toward the keyboard.
2.
Hold in position.
3.
Press locking display latch.
4.
Release pressure on display.
5.
Pivot both locking handles up and inward until they engage the locking tab on the display.
Windows Set-up
The first time you power on your ReVolution, a series of screens will inform you of operating system setup options
and prompt you for personal preferences. Simply follow the onscreen instructions to finish the setup of your operating
environment.
Accessing the User Manual
To view or obtain additional copies of this ReVolution User Manual, you may:
1.
Insert the ReVolution Utility CD that came with the original shipment of your ReVolution computer. This CD
contains an electronic copy of the manual.
2.
Go to www.kontronmobile.com. Select the following path: Technical Support ĺTechnical SearchĺManual.
3.
Call or write the Kontron Technical Support department to order additional hard copies. Contact information is
located on the Technical Support page.
22
02/18/05
ReVolution User Manual 1.00
This page was intentionally left blank.
ReVolution User Manual 1.00
02/18/05
23
Modifying the System
This section describes how to use and adjust the components and devices of the ReVolution. You will find
instructions for removing and inserting the following components:
x
x
x
x
x
x
Alternative Display
Battery Pack
Hard Disk Drive-Master
Left Bay Modules (CD-ROM, Floppy Disk Drive, etc.)
PCMCIA Cards
Shoulder Straps
You will find information about the following devices in this section:
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Audio
Chipset
LAN
Modem
Touchscreen
Touch Pad
USB 2.0
Video
Wireless 802.11b/g
Wireless Bluetooth
CD-ROM
DVD
Power Management Modes
Volume Level
You can find device drivers for operating systems such as Microsoft Windows on the ReVolution Utilities CD shipped
with the unit. Occasionally there will be special instructions on how to properly install a device driver. These
instructions are stored in the directory of the device driver in a text file for your reference.
Drivers on the ReVolution Utilities CD include:
x
x
x
x
x
x
x
x
x
x
x
Audio
Chipset
LAN
Modem
Touchscreen
Touch Pad
USB 2.0
Video
Speed Step
Wireless 802.11b/g
Wireless Bluetooth
Alternative Display
For some applications, you may want to use an additional SVGA monitor. To connect an SVGA display to your
ReVolution, you must use an optional I/O extension stick (port replicator).
24
02/18/05
ReVolution User Manual 1.00
Battery Packs
The right front bay only accepts a lithium ion battery pack that will provide approximately 3.5 hours of operating time.
This bay contains the main or primary battery source. This section describes how to remove a battery pack from, and
insert one into, the right front bay. Refer to the “Left Bay Modules” section for information on removing and inserting
an additional or secondary battery pack into the left bay. Refer to the “Power Management Modes” section for more
information on battery operations.
x
The photograph above shows the angles at which you
insert a battery into the right bay and left bay.
x
Insert a battery into the right bay sideways, with battery
label facing up and a set of the battery contact points
facing away from you and positioned in the front LEFT
portion of the battery pack.
x
Insert a battery into the left bay length-wise, with battery
label up and a set of battery contact point facing away
from you and positioned in the front RIGHT portion of
the battery pack .
x
If two batteries are inserted and both are charged, the
computer can be on when you remove or insert one or
the other of the batteries.
x
If two batteries are used during operation, the system is
designed to deplete the “secondary” or Left Bay battery
first.
Removing Battery from Right Bay
•Push ejector latch forward.
•The battery pack ejects.
•Open door of right front bay.
•Turn unit over.
ReVolution User Manual 1.00
02/18/05
25
Inserting Battery into Right Bay
To insert a battery into the right front bay:
x
x
x
x
x
Open the right bay door.
Insert a battery into the right bay sideways, with battery label facing up. A set of the battery contact points facing
away from you and positioned in the front LEFT portion of the battery pack.
Align the latch post at the bottom of the battery with the receiving slot on the bottom of the bay.
Carefully slide the battery into the bay until it locks into place.
Close and lock the door.
‰ The system will notify you when the main power source
has been lost, and the unit is running on battery power.
When the system is running on battery power, the
computer will sustain approximately 3.5 hours of
operating time.
‰ The system will monitor the presence of external input
voltage and the battery pack voltage. It will begin to
charge whenever it detects a low battery voltage
condition and stop charging when one or both batteries
are fully charged.
‰ The system charges one battery at a time, charging the
left battery fully, then the right battery.
‰ Charge time with system power off takes up to 3.5 hours
per battery. With system power on, charge time takes up
to 7 hours per battery.
‰ For faster battery charging, Kontron recommends the
optional external battery charger listed in the “Base Unit
and Optional Parts” section of this manual.
26
02/18/05
ReVolution User Manual 1.00
Hard Disk Drive - Master
The ReVolution comes standard with a master removable hard disk drive, located inside the bottom panel. An
upgrade to 60GB is available. The following two series of photographs demonstrate how to remove and insert a hard
disk drive module.
x Turn off the computer before removing or inserting the hard disk
drive module.
Removing a Hard Disk Drive (HDD)
• Make sure all module doors are closed.
• Lay unit on its top.
• Push slide latch to right
• Remove door.
• Lift handle on HDD module to 90° angle.
• Slide module back until it disengages from connector.
• Lift module straight up.
ReVolution User Manual 1.00
02/18/05
• Remove module from bay.
27
Inserting a Hard Disk Drive (HDD)
• Lift handle on HDD module up to 90° angle.
• Align posts on sides of module with receiving
slots in HDD bay.
• Close top display so only metal is exposed.
• Lay unit on its top.
• Push slide latch to right.
• Remove HDD door.
• Push module down until it reaches bottom of the bay.
• Pull forward until it fully engages HDD connector.
• Press handle back down. The module must be fully
engaged with the connector for the handle to fit down.
• Replace HDD module door.
• Move slide latch left until it reaches stop point.
28
02/18/05
ReVolution User Manual 1.00
Left Bay Modules
The left front bay of the ReVolution accepts the following modules:
x CD-ROM
x CD-RW (read-write)
x Floppy Disk Drive
x DVD
x DVD/CD-RW Combo
x Slave Hard Disk Drive
x Battery Pack
All these modules can be inserted and removed from the left bay in the same manner, as demonstrated below. The
computer can be on when performing these functions. However, if the modules are not in the bay when the system is
started, the system will not recognize them if added or swapped while the system is running. You will have to reboot
for the system to detect the module.
CD-ROM, CD-RW, DVD and DVD/CD-RW Modules
x
Use of controls, adjustments or performance of
procedures other than those specified herein may result
in hazardous laser radiation exposure.
x
The laser beam used in any laser equipped drive unit
can be harmful to the eyes. Never look directly at the
laser read head while changing discs.
x
Use discs that bear the COMPACT DISC logo.
x
Handle discs by their edges.
x
Store discs in their cases to minimize dust,
contamination, scratches, bending or other damage.
x
Periodically wipe each disc with a soft, dry cloth, gently
rubbing outward from the center.
DO NOT:
x
Expose computer to a sudden impact or excessive
vibration.
x
Touch the bottom surface of the disc.
x
Bend a disc.
x
Write on a disc with a hard object, such as a ballpoint
pen or pencil.
x
Affix any label directly on a disc.
x
Expose discs to direct sunlight.
x
Store discs in areas subject to high temperatures or
humidity.
x
Use fluids such as Benzene, record cleaning fluid, or
anti-static fluid, that can damage the drive mechanism or
lens.
ReVolution User Manual 1.00
02/18/05
29
Removing any Left Bay Module
• Push ejector latch forward.
• The module ejects.
• Remove module carefully and place it
in a safe, clean location.
Inserting any Left Bay Module
To insert any of the modules listed above:
x
x
x
x
Place the computer right-side up.
Open the door of the left front bay.
Align the latch post at the bottom of the module with the receiving slot on the bottom of the bay.
Carefully slide the module into the bay until it locks into place.
x
30
Align the groove on the battery bottom with the guide in
the bay to insert properly.
02/18/05
ReVolution User Manual 1.00
PCMCIA Cards
Two PCMCIA slots on the back interface panel accept two Type II PC Cards or one Type III PC Card. You can insert
and remove the cards while the computer is on.
Top Card Ejector
Top Card Slot
Bottom Card Ejector
Bottom Card Slot
To remove a card from the top card slot,
press the top card ejector button.
To remove a card from the bottom card slot,
press the bottom card ejector.
To insert a PC card, carefully slide the card
right-side up into one of the card slots until
the card clicks.
ReVolution User Manual 1.00
x
The peak power consumption of each of the PCMCIA
slots may not exceed 3.3 Watts Peak (600 mA at +5 V).
x
Follow the card manufacturer's instructions in the PC
Card documentation.
x
Do not force a PC Card into or out of the slot.
x
Prevent external debris from entering the slot.
x
Make sure that the PC cards all have the legally
prescribed approvals (e.g. IEC/EN 60950).
x
The ReVolution has an extended temperature range.
This might be not the case with your PC Card. Please
note that the operating temperature range could be
decreased for the whole system depending on the
manufacturer’s recommended temperature range for
the PC card that you want to use.
02/18/05
31
Shoulder Straps
All four corners of the ReVolution have a catch on which to attach a shoulder strap. Choose the two corners most
comfortable for you. The following photographs display how to attach the two ends of the strap to the computer.
• Attach the hook end of the shoulder strap to the catch.
• Repeat steps one and two with another corner.
• Extract the recessed catch from the corner.
The shoulder strap attaches to any two of the
four corners.
32
02/18/05
ReVolution User Manual 1.00
Audio
The audio system is made up of an AD1881A, which meets the Audio Codec ’97 2.0 and 2.1 Extensions. The main
architectural features of the AD1881A are the high-quality analog mixer section, two channels of Ȉǻ ADC conversion,
two channels of Ȉǻ DAC conversion with Data Direct Scrambling (D S) rate generators.
The audio system has three 3.5 mm diameter jacks: a microphone input, speaker output and line in.
x
The Microphone Jack allows you to receive monophonic input from an external microphone.
x
The Speaker Output Jack allows you to directly drive external speakers at 1W.
x
The Line-In Jack allows you to receive stereo line-level audio input from an external source.
This audio system enables you to enjoy various multimedia audio features. This audio chip provides the following
features and more:
x
Recording and playing back of PCM and WAV files in 8-bit or 16-bit format.
x
Sampling of various rates from 8 KHz to 48 KHz for the WAV file.
x
Playback of MIDI files through an FM synthesizer.
x
Recording from various sound sources, such as an integrated microphone, an external microphone, or an
audio device attached to the line-in jack.
Volume Level
The ReVolution will adjust the speaker output level when you change the volume slider on the Windows task bar or
press the volume up/down function keys.
CD-ROM, CD-RW, DVD and DVD/CD-RW Combo Module Drives
x
All these modules can be inserted and removed from the left bay
in the same manner. The computer can be on when performing
these functions. However, if the modules are not in the bay when
the system is started, the system will not recognize them if added
or swapped while the system is running. You will have to reboot
for the system to detect the module.
Software Installation- CD writer
With the CD-RW drive module installed in the ReVolution, you can record using CD-R(CD-Recordable) or CD-RW
(CD-ReWritable) discs. Types of files you can record are backup files, pictures and movies, or your own creation of
audio files. Easy to use CD recording software is included with the CD-RW drive.
For more information, refer to the CD-RW software provided with the drive package.
Software Installation - DVD player
With the DVD drive installed in the ReVolution, you can play DVD movies. Easy to use DVD software is included with
the DVD drive.
For more information, refer to the DVD software provided with the drive package.
ReVolution User Manual 1.00
02/18/05
33
Chipset
The ReVolution uses the Intel 830M and ICH4 chipset. This chipset incorporates the Video, IDE, USB, and AC97
sub-systems. Specialized operating system drivers are located on the utilities CD shipped with your ReVolution and
must be installed to maximize the performance of this chipset. If you ordered your ReVolution with an operating
system pre-installed you will not need to install these drivers, these drivers are installed for you at the factory.
Driver Installation: Chipset
The Intel chipset driver is installed at the factory for your ReVolution. If special instructions are available for driver
installation for the chipset, you will find these instructions in the directory that contains the driver.
Driver Installation: Application Accelerator
The Intel Application Accelerator software is designed to improve hard drive interface performance. Review the
documents in the application accelerator directory on the CD or on Intel’s web site to learn more about the details of
this software.
LAN - Embedded
The built-in network feature allows you to connect your computer to an Ethernet-based (10/100/1000) Mbps) network
via the RJ-45 jack. To use the network feature, connect an Ethernet cable from the network jack on the rear of the
computer to a network jack or hub on your network.
Modem
Via the RJ-11 on the back interface panel, you have access to a PCI V.90/K56flex modem. This modem design is
based on Lucent Technologies L56xMF (Mars II) PCI bus host-based modem controller chip set. This chip set has a
high level of integration with the advantage of letting the DSP perform MIPS-intensive operations, such as V.90 and
K56flex, while consuming the host with less MIPS-intensive functions, such as V.42bis.
This modem includes data, fax and TAM (telephone answering machine) functions. It complies fully with Microsoft’s
PC98 and PC99 requirements, and supports both APM and ACPCI power management.
The DAA of this modem is designed to comply with the regulations of the following countries:
x
-America:
US, Canada
x
-Asia:
Japan, Malaysia, Singapore, Hong Kong, Australia, New Zealand
x
-Europe:
CTR21 - 18 European Countries:
Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Norway, Portugal, Spain, Sweden, Switzerland, Netherlands and UK.
You can use the built-in modem only on a public-switched telephone network (PSTN). You cannot use a private
branch exchange (PBX) or some other type of digital telephone extension line. If you connect the built-in modem to a
line other than PSTN, an error message appears, preventing you from using the line. If you are not sure which kind of
phone line you are using, contact your telephone company.
34
02/18/05
ReVolution User Manual 1.00
Power Management Modes
Windows
Your ReVolution will manage power consumption while running the Windows operating system, based on the settings
in Windows Control Panel power options. To maximize battery run-time, be aware of the settings affecting power
consumption. In addition to Control Panel power options, the following items can influence battery run time:
x
x
x
LCD backlight level
Intel Speed Step mode
Wireless network settings
Set the power management properties for your application in Windows Power Options.
If you are running an operating system that does not fully support power management (APM or ACPI), such as
Legacy, you can set basic power management features in BIOS setup. Refer to the “Phoenix BIOS Setup” section
in this document for these settings.
ReVolution User Manual 1.00
02/18/05
35
Battery Operations
The right bay battery is the primary battery source and is identified as battery number 1. The left bay battery is the
secondary battery source identified as battery number 2. Using two or more batteries will allow you to swap charged
batteries into the module bays for extended portable operation.
Single battery operation
The ReVolution running on a single battery will deplete battery charge until an alarm level is met then trigger the
action set for that alarm. Set the alarm level and action in Power Options in Windows Control Panel.
Stand-by battery operation
When running the ReVolution with two charged batteries, the secondary battery will be depleted first. The primary
battery will power the ReVolution when the secondary battery is empty, keeping the ReVolution running as a stand-by
battery. Replace the depleted secondary battery with a charged battery to resume powering the ReVolution on the
secondary battery.
Alternate battery operation
Place a battery in either bay and run the ReVolution until a low battery message is displayed. Place a charged battery
in the remaining open bay to continue operation and remove the discharged battery.
36
02/18/05
ReVolution User Manual 1.00
Touchscreen
Your ReVolution is designed with a resistive touch screen that acts as a mouse pointer. Use the provided stylus for
best results.
Stylus
User Settings
Multiple behavior settings are available for the touchscreen. Your preferences may differ from the default settings for
interacting with screen objects. You can change these settings by:
x
x
x
Running the touchscreen property sheet from the Start-Programs-UPDD-Settings menu,
Clicking on “Pointer Device Settings” in the system tray, or
Running “Pointer Devices” in Windows Control Panel. The following screen will appear.
x
x
x
x
Navigate the Settings and Advanced tabs to adjust click responsiveness.
Select the Events tab to program the mouse event that executes when touching the screen.
The Windows tab provides double-click settings and a test area to try your new settings.
Click the Help button if you need more information.
Driver Installation
The driver for your touchscreen is loaded at the factory when you order a Microsoft Windows operating system. If you
need to reload the driver, use the ReVolution Utilities CD included with your unit.
ReVolution User Manual 1.00
02/18/05
37
Calibrate
The ReVolution touchscreen is calibrated at the factory. Run the calibration routine when an alignment problem exists
between the mouse pointer and the stylus contact location on the screen. You can adjust the calibration of the
touchscreen by running the program at Start-Programs-UPDD-Calibrate. Carefully touch the location of the markers
with your stylus to recalibrate the touch screen.
After calibrating the ReVolution touchscreen you can test the alignment by pressing the Test button to view the
tracking accuracy.
38
02/18/05
ReVolution User Manual 1.00
Touch Pad
The built-in touch pad is a PS/2-compatible pointing device that senses movement on its surface; the cursor responds
as you move your finger on the surface of the touch pad. The central location on the palm rest provides optimal
comfort and support.
Touch Pad Basics:
1.
Move your finger across the touch pad to move the cursor.
2.
Press the left and right buttons located on the bottom edge of the touch pad to select and execute. These two
buttons are similar to the left and right buttons on a mouse. Tapping on the touch pad produces similar results.
Function
Execute
Left Button
Click twice quickly
Select
Drag
Click once
Click and hold, then use
finger to drag the cursor on
the touch pad
Access Content Menu
Scroll
Right Button
Tap
Tap twice (at same speed
as double-clicking a mouse
button)
Tap once
Tap twice (at same speed
as double-clicking a mouse
button), then hold finger to
the touch pad on the
second tap and drag the
cursor.
Click once
Note: Keep your fingers clean and dry when using the touch pad. Also keep the touch pad dry and clean. The touch
pad is sensitive to finger movements. Hence, the lighter the touch, the better the response. Tapping harder will not
increase the touch pad’s responsiveness.
Change the behavior of the touch pad by adjusting the Mouse Properties in the Microsoft Windows Control Panel,
displayed on the following page. For additional touch pad control, load the touch pad driver found on the ReVolution
Utilities CD included with your unit.
ReVolution User Manual 1.00
02/18/05
39
Special touch pad features allow greater control of touch pad usage. Familiarize yourself with these features on this
screen.
USB Ports
Driver Installation
The ReVolution is designed with a USB 2.0 compliant controller that requires an operating system driver to exploit its
capabilities. The driver is preinstalled at the factory and a backup of the driver is on the ReVolution Utilities CD
delivered with your system.
40
02/18/05
ReVolution User Manual 1.00
Video
The ReVolution is designed with the Intel i830M grapics and memory ccontroler (GMCH). You can control the video
system through the Microsoft Windows Control Panel. You can also gain quick access to video options by clicking the
Intel Graphics Technology icon in the system
tray or by right clicking on the desktop, as follows.
ReVolution User Manual 1.00
02/18/05
41
The Graphics Controller property sheet through the Windows Control Panel allows you view and change device color
depth, resolution, color correction, display schemes, and hot keys.
Driver Installation
Browse the ReVolution Utilities CD to locate the video driver installation. Intel frequently updates the graphics drivers
for ICH4. Download this driver from www.intel.com.
42
02/18/05
ReVolution User Manual 1.00
Video Rotation
The ReVolution can change the orientation of the display image in four degrees of rotation. Rotating the screen can
be useful when running the ReVolution in tablet mode, to suit your workspace. The normal orientation when in laptop
mode is zero degrees. You may want to switch to 90 or 270 for a “Portarit” display or simply flip the screen by
setting 180 rotation. There is three ways to change screen rotation. Use the system tray icon, right click on the
desktop, or use the hot keys.
Hot Key Rotation:
To rotate your screen's image press  +  and hit the  key.
Rotate to 0 press  +  and hit the <0> key.
Rotate to 90 press  +  and hit the <9> key.
Rotate to 180 press  +  and hit the <8> key.
Rotate to 270 press  +  and hit the <7> key.
Task Bar Rotation
Desktop Rotation:
ReVolution User Manual 1.00
02/18/05
43
Wireless - 802.11b/g (WLAN)
Do not operate the ReVolution in areas sensitive to radio
interference, such as airplanes and hospitals.
There is no means to shut off the Bluetooth and WLAN radios installed in the
system.
The integrated Wireless LAN (WLAN) device in the ReVolution is an 802.11b/g wireless network card that is attached
to the computer via a mini-PCI slot.
The main characteristics include:
x
Operating frequency in the 2.4 GHz band.
x
Compliance with WECA Wireless Fidelity (Wi-Fi) testing standard and ability to communicate up the maximum
transfer rate of 11 Mbps.
x
Maximum range of about 105 Meters.
This device provides a plug-and-play seamless connectivity to all network resources, and Internet access at up to 11
Mbps. No cables are necessary to run, just an access point. It provides a high-speed connectivity at up to 11 Mbps
over an extended operating range. It automatically falls back to 5.5, 2, and 1 Mbps. It is compliant with IEEE 802.11b/g
standards which also assures compatibility with other 802.11b/g compliant devices and networks.
Frequency Range:
Typical outdoor operating range
Modulation Technique:
Channel Support
2.4 GHz to 2.4835 GHz
30 M @ 11 Mbps
50 M @ 5.5 Mbps
100 M @ 2 Mbps
105 M @ 1 Mbps
DSSS(Direct Sequence Spread Spectrum) with BPSK (1Mbps),
QPSK (2Mbps), and CKK(5.5 and 11 Mbps), OFDM
US/Canada: 11 (1 ~ 11)
Major European Country: 13(1 ~ 13)
France: 4(10~13)
th
Japan: 14(1 ~ 13 or 14 )
Driver
The software for the WLAN allows you to view and set the connection to other 802.11b/g devices. Run this utility by
navigating to Start-Programs-IEEE 802.11b/g MiniPCI Utility in Windows 2000 or Windows 98. The following screen will
appear. When running Windows XP go to Device Manager.
44
02/18/05
ReVolution User Manual 1.00
To secure transmissions with an 802.11b/g device that has WEP enabled, set a pass phrase or key on the Advanced
Setting window.
ReVolution User Manual 1.00
02/18/05
45
Wireless - Bluetooth
Do not operate the ReVolution in areas sensitive to radio
interference, such as airplanes and hospitals. There is no
means to shut off the Bluetooth and WLAN radios installed in the system.
For PAN environments, Bluetooth provides freedom from wired connections. By using this radio-based link,
computers, mobile phones, PDA and other portable handheld devices are able to transmit data to each other or
connect to Internet without a single cable.
While the possibilities are nearly endless for the applications of the technology, some of the current capabilities
include:
x
x
x
x
x
Eliminating the need for wired connections between electronic products and accessories such as a keyboard,
mouse, headsets, printers, other computers;
Exchanging files, business cards, calendar appointments, etc. with groups of Bluetooth users;
Transferring and synchronizing files between devices;
Connecting to localized content services in public areas;
Functioning as remote controls, keys, tickets and e-cash wallets.
The Bluetooth wireless technology and Wireless LAN (802.11b/g) are complementary technologies. The Bluetooth
wireless technology is designed to replace cables between cell phones, laptops, and other computing and
communication devices within a 10-meter range. Wireless LAN is wireless Ethernet; it provides an extension or
replacement of wired networks for dozens of computing devices.
Issues do arise with the coexistence of both Bluetooth and Wireless LAN. Any time devices are operated in the same
frequency band, there is the potential for interference which results in a lower bandwidth
This device has a maximum range of about 10 meters, depending on the environment. The maximum data transfer
rate is 1.0Mbps. This is a Class 2 device with a typical Tx power of 2+/-0.5 dBm. The operating frequency range is 2.402
GHz to 2.480 GHz with a channel spacing of 1 MHz.
46
02/18/05
ReVolution User Manual 1.00
Technical Data
ReVolution
Main Specification
Processor
Intel Mobile Pentium® III-M 1.6 GHz or higher
Main Battery
Lithium Ion battery - 57 Watt, 3.5 hour life (approximate)
BIOS:
AMI BIOS 8.00.10
RAM:
512 MB DDR standard
L2-Cache
512KB
Keyboard:
Full-size QWERTY keyboard with 84 keys (USA Standard)
Interfaces:
1x Power Connector with 10-28 VDC, 4.6 Amps
1x Serial Port (COM 1)
2x USB 2.0 Ports
1x1394 port
Docking connector
1x RJ11 56K V.90 Modem
1x RJ45 10/100Mbs Ethernet/LAN
Audio phonejacks:
1x MIC-In
1x Line-In
1x Speaker-Out
Integrated: 802.11b/g WLAN, Bluetooth PAN
Hard Disk
Drives:
40GB primary removable hard drive standard – upgradeable
to 60GB
40GB secondary, optional removable hard drive –
upgradeable to 80MB
Call Technical Support or your Sales Representative for other
available options.
PCMCIA:
Card BUS connector provides two open PC Card slots that
accommodate two Type II, or one Type III PCMCIA device.
Graphics
Controller:
Integrated Direct AGP Graphics
Core frequency up to 166 MHz
350 MHz RAM DAC
Video-RAM: 8 to 48 MB of Dynamic Video Memory (shared)
Up to 32 MB with 128 MB RAM; 48 MB with 256 MB RAM
Pointing
Device:
Touch Pad on the keyboard, Touchscreen on the display
Power
specification
10-24 VDC
AC adapter:
Input: 90-264 VAC, 50-60 Hz; Output: 12V, 55W
RTC/CMOS
Battery
Rechargeable LIon real-time clock/CMOS battery on main
board. Not user-serviceable.
ReVolution User Manual 1.00
02/18/05
47
Mechanical Specification
Dimensions:
Width
12.8" (326 mm)
Depth
10.25" (261 mm)
Height
2.125" (54 mm)
Weight:
8 lbs. with one battery module installed.
Chassis:
Rigid, lightweight magnesium design
Environmental Specifications
Operating temperature
–15 C to +50°C
(5 F to 140 °F)
NOTE: Excludes all CD-ROM, DVD and floppy
devices. See device specifications later in
this section.
Storage temperature
–20 C to +70 °C
(–4 F to 158 °F )
NOTE: Excludes all CD-ROM, DVD and floppy
devices. See device specifications later in
this section.
Operating humidity
10–88 % relative humidity, non-condensing
Storage humidity
5–95 % relative humidity, non condensing
Shock
Mil-Std 810F:
Method: 516.5
Procedures:
I = 40G
IV = 26 drops @ 36”
V = 75G
NOTE: Excludes all CD-ROM, DVD and floppy
devices. See device specifications later in
this section.
Vibration
Mil-Std 810F:
Method: 514.5
Procedure I
Category 20 & 24
Blowing Rain
IP54/NEMA 3
Sand and Dust
NEMA 3
Altitude Operating
Up to 15,000 ft. (4,500 m)
Altitude Non-Operating
Up to 35,000 ft. (10,668 m)
EMI & Safety
FCC Part 15 Class B (ETSI 300 328/1997)
CE Directive Class B (ETSI 301489-17/2002)
UL, EN 60950
48
02/18/05
ReVolution User Manual 1.00
CE-Directives and Standards
CE –Directives
Low Voltage directive
(Electrical Safety)
EN 60950
EMC Directive
EN 55022
Electrical Safety
Standards
U.S.A.
UL 60950/2002
Canada
CSA 22.2 No. 60950-00
EMC
Standards
U.S.A.
FCC Part 15.247/2002
ReVolution User Manual 1.00
02/18/05
49
CD-ROM Module
Interface
IDE
Temperature range
in operation: 5°C to +50°C
in storage: -30°C to +65°C
Humidity
5% - 90% (relative, non-condensing)
Features
Read Data 24X CAV max.
Audio Play 8X CAV max.
CD-RW Module
Interface
IDE
Temperature range
in operation: 5°C to +50°C
in storage: -20°C to +60°C
Humidity
10% - 80% (relative, non-condensing)
Features
Write 8X max.
Read 24X max.
DVD Module
Interface
IDE
Temperature range
in operation: 5°C to +50°C
in storage: -30°C to +65°C
Humidity
5% - 90% (relative, non-condensing)
Features
DVD-ROM 24X CAV max.
CD 8X CAV max.
DVD/CD-RW Module
Interface
IDE
Temperature range
in operation: 5°C to +50°C
in storage: -20°C to +60°C
Humidity
10% - 80% (relative, non-condensing)
Features
Read:
DVD-ROM 8X CAV max.
CD-ROM 24X CAV max.
Write:
CD-R 8X CLV
CD-RW 4X CLV
High Speed CD-RW 8X CLV
50
02/18/05
ReVolution User Manual 1.00
Floppy Disk Drive Module
Interface
TTL
Temperature range
in operation: 5°C to +50°C
in storage: -40°C to +60°C
Humidity
20% - 80% (relative, non-condensing)
FDD:
3.5" 1.44Mb Formatted
Lithium Ion Battery Pack
Interface
SMBUS VI.0
Temperature range
Operating: 0° to +45°C charging
-20° to +60°C discharging
Service Life
300 Cycles typ.
Typical Capacity
8800mAH@.2C
Nominal Voltage
7.40V
Remaining Capacity LEDs:
Green (Three)
76-100% remaining
Green (Two)
51-75% remaining
Green (One)
26-50% remaining
Red
0-25%
ReVolution User Manual 1.00
02/18/05
51
Technical Appendices
The following tables show the connector pin-out assignments for the external connections of the ReVolution computer.
Active low signals are indicated by a minus sign. Refer to the “ReVolution at a Glance” section for locations.
RS232 Serial Port (COM A)
Pin
Signal name
DCD (Data Carrier Detect)
RXD
(Receive Data)
TXD
(Transmit Data)
DTR
(Data Terminal Ready)
GND (Signal Ground)
DSR
(Data Set Ready)
RTS
(Request to Send)
CTS
(Clear to Send)
RI
(Ring Indicator)
9-pin SUB D-plug
Parallel Port (I/O Stick Option Only)
Pin
Signal name
–STROBE
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
10
–ACKN
11
BUSY
12
PE
13
SELECT
14
–AUTOFD
15
–ERROR
16
–INIT
17
–SLCTIN
18–25
GND
52
25-pin SUB D-socket
02/18/05
ReVolution User Manual 1.00
Analog Monitor (VGA-Output, I/O Stick Option Only)
Pin
Signal name
red
green
blue
4, 5
4 is NC, 5 is GND
6–8
GND
not connected
10–12
10-GND, 11-NC, 12-DDC Data
13
HSYNC
14
VSYNC
15
DDC Clock
15-pin SUB D-socket
USB 2.0 Ports
Pin
Signal name
+5 Volts
P-
P+
GND
USB
Power Supply Connector
Pin
Signal name
4-pin Female socket
(Looking into socket on back
interface panel))
Ground
Ground
DC Input(+10 to +28 Volts DC)
DC Input(+10 to +28 Volts DC)
ReVolution User Manual 1.00
02/18/05
53
PS/2 Keyboard/Mouse Connector (I/O Stick Option Only)
Pin
Name
Dir.
Description
DATA
Mouse Data
DATA
Keyboard Data
GND
Ground
VCC
Power , +5 VDC
CLK
Mouse Clock
CLK
Keyboard Clock
This illustrates the pin-out of the external PS/2 Keyboard/Mouse connector. This connection is “hot pluggable” and
interchangeable between the external keyboard and the external mouse. Hot pluggable means you may connect
either the external keyboard or external mouse while the computer power is on.
RJ-11 Modem Port
Pin
Name
Not Connected
TIP
RING
Not Connected
RJ-45 LAN Port
Pin
Name
Description
TX+
Transmit Data+
TX-
Transmit Data-
RX+
Receive Data+
Not Connected
Pin 4 is shorted to Pin
5 then AC coupled to
ground through a 75
Ohm resistor
Not Connected
See Above
RX-
Receive Data-
Not Connected
Pin 7 is shorted to Pin
8 then AC coupled to
ground through a 75
Ohm resistor
Not Connected
See Above
54
RJ-45 LAN Port
02/18/05
ReVolution User Manual 1.00
Line-In
LINE IN RIGHT
LINE IN LEFT
AGND_A
MIC-In
MUTE
MIC
AGND_A
Speakers
SPEAKER RIGHT
MUTE_S
SPEAKER RIGHT
AGND_A
ReVolution User Manual 1.00
02/18/05
55
System Hardware Assignments
The ReVolution, like all computers based on standard IBM-compatible personal computer architecture, contains a set
of user hardware- and software-configurable resources. The system uses some of these resources for various
standard and optional features. The user can modify others.
This section describes the standard system resources, their use and assignment status.
The following table of Interrupt ReQuests (IRQs) are assigned by the BIOS. Plug-and-play operating systems
(Windows 98/2000/XP) may change the IRQ assignments.
Table of IRQ Assignment by BIOS
IRQ Number
Use
Type
Status
Timer
ISA
Permanent Assignment
Keyboard
ISA
Permanent Assignment
Programmable Interrupt
Controller
ISA
Permanent Assignment
COM Port B (2)
ISA
BIOS enable/disable
COM Port A (1)
ISA
BIOS enable/disable
PNP/PCI
Floppy Disk
ISA
Permanent Assignment, if installed
LPT1
Real Time Clock
ISA
Permanent Assignment
ACPI EC
LPC
PNP/PCI Assignment
BIOS Adjustable
10
PNP/PCI
11
PNP/PCI
12
Mouse
ISA
BIOS enable/disable
13
Math Coprocessor
ISA
Permanent Assignment
14
IDE Controller
ISA
PCI/PNP assignment
15
DMA Channel Table
DMA Channel
56
Use
Status
Unused
Available To User
Unused
Available To User
Floppy Disk
Permanent Assignment
ECP Parallel Port
BIOS adjustable
DMA Controller
Permanent Assignment
Unused
Available To User
Unused
Available To User
Unused
Available To User
02/18/05
ReVolution User Manual 1.00
Embedded Controller
The Embedded Controller (EC) in the ReVolution supervises its “power state” by monitoring incoming power levels
and temperature, making decisions for safe operation. The EC also interacts with the system BIOS and informs the
APM manager with power-related messages. When a fault condition occurs, the EC will change the power state and
indicate the fault by flashing a series of codes on the power LED:
Embedded Controller LEDs
Refer to the “ReVolution at a Glance” section for LED locations.
Symbol
Name
NumLock
Battery Indicator
Purpose
Indicates NumLock state. LED is on when NumLock
is active.
Indicates capital letter state. LED is on when Caps
Lock is active.
Indicates battery status
Power
Indicates AC power attached
Hard Disk Drive Activity
Indicates when hard drive is accessed.
LAN Activity
Indicates embedded LAN activity.
Wireless Activity
Future Use
Mail
Future Use
Caps Lock
You must clear the active fault before the EC will continue operation. The EC is continuously on when power is
applied to the ReVolution. It is field-upgradeable.
The EC will perform a power-down override, which forces the ReVolution to turn off, when a user presses the power
on/off button continually for 4 seconds.
Note: The Embedded Controller is active whenever there is a DC power source (external or battery) present, even
with ReVolution power off. If the ReVolution is stored with one battery installed, the EC will discharge a fully charged
battery in approximately 27 days. Kontron recommends that the ReVolution be stored for extended periods with no
battery installed.
Power and Battery Indicators
Power State
OFF
On, Charging
Low Battery
Running on battery
Running on AC not charging
Battery Malfunction
Sleep mode battery
Sleep mode AC
Power LED
OFF
ON
OFF
OFF
ON
Fast Blink
Slow Blink
OFF
Battery Indicator LED
OFF
Slow Blink
Fast Blink
ON
OFF
Fast Blink
OFF
Slow Blink
Slow blink is defined as - 0.5 Hz, 50% duty cycle, i.e. ON for one second, OFF for one second
Fast blink is defined as - 1 Hz, 50 % duty cycle, i.e. On for 500 ms, OFF for 500 ms
ReVolution User Manual 1.00
02/18/05
57
Phoenix BIOS Setup
Use the Phoenix BIOS Setup program for:
x Setting system time and date.
x Installing new drives for hard disks and floppy disks.
x Enhancing system performance by controlling advanced features such as shadow memory and cache
memory.
To start the Phoenix BIOS Setup utility:
1. Turn on or reboot your system.
2. Press the ESC key when ReVolution splash screen appears.
3. PhoenixBIOS displays this message: Press  to enter SETUP
4. Pressing  displays the Main Menu.
Incorrect settings can cause your system to malfunction.
Navigating the Setup Menus
The Menu Bar at the top of the window lists these selections:
Main
Advanced
Security
Power
Exit
Use this menu for basic system configuration.
Use this menu to set the Advanced Features available on your system's chipset.
Use this menu to set User and Supervisor Passwords and the Backup and Virus-Check reminders.
Use this menu to configure Power-Management features.
Exits the current menu.
Use the left/right Å Æ arrow keys to make a selection.
Legend Bar
Use the keys listed in the legend bar on the bottom of the screen to make your selections or exit the current menu.
The chart on the following page describes the legend keys and their alternates:
Key Function
 or 

ļ Left or right ҏarrow keys
Ľҏ Up or down ҏarrow keys
 or 
 or 
 or 
 or <->
 or <+> or 




General Help window (See below).
Exit this menu.
Select a different menu.
Move cursor up and down.
Cycle cursor up and down.
Move cursor to top or bottom of window.
Move cursor to next or previous page.
Select the Previous Value for the field.
Select the Next Value for the field.
Load the Default Configuration values for this menu.
Load the Previous Configuration values for this menu.
Execute Command or Select P Submenu.
Refresh screen.
To select an item:
x Use the arrow keys to move the cursor to the field you want.
x Use the plus-and-minus value keys to select a value for that field. The Save Values commands in the Exit Menu
save the values currently displayed in all the menus.
To display a sub menu:
x Use the arrow keys to move the cursor to the sub menu you want.
x Press . A pointer (_) marks all sub menus.
58
02/18/05
ReVolution User Manual 1.00
Field Help Window
The Help window on the right side of each menu displays the help text for the currently selected field. It updates as
you move the cursor to each field.
General Help Window
Advanced Hard Disk Features
If Advanced Hard Disk Features are installed, select one of the Master or Slave sub-menus on the Main Menu.
Use the legend keys listed on the bottom to make your selections and exit to the Main Menu.
Use the chart on the following page to configure the hard disk drive with Advanced Hard Disk Features:
ReVolution User Manual 1.00
02/18/05
59
Advanced Hard Disk Features
Feature
Options
Type
None
User
Auto (Default)
IDE Removable
CD-ROM
ATAPI Removable
Cylinders
Heads
Sectors
Multi-Sector Transfers
1 to 65,536
1 to 16
Description
None = Autotyping is not able to
supply the drive type, or end user has
selected None, disabling any drive
that may be installed.
User = You supply the hard-disk
drive information in the following
fields.
Auto = Autotyping, the drive itself
supplies the information.
IDE Removable = Removable disk
drive
CD-ROM = CD-ROM drive.
ATAPI Removable = Removable
disk drive.
Number of cylinders.
Number of read/write heads.
Disabled
Standard
2 sectors
4 sectors
8 sectors
16 sectors
Enabled
Disabled
Any selection except Disabled
determines the number of sectors
transferred per block. Standard is 1
sector per block.
32-Bit I/O
Enabled
Disabled (Default)
This setting enables or disables 32-bit
IDE data transfers.
Transfer Mode
Standard
Fast PIO 1
Fast PIO 2
Fast PIO 3
Fast PIO 4
OR
Standard
Fast DMA A
Fast DMA B
Fast DMA F
Disabled
Mode 0
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Selects the method for transferring
the data between the hard disk and
system memory. The Setup menu
only lists those options supported by
the drive and platform.
LBA Mode Control
Ultra DMA Mode
60
Enabling LBA causes Logical Block
Addressing to be used in place of
Cylinders, Heads, & Sectors.
Selects the Ultra DMA mode used for
moving data to/from the drive.
Autotype the drive to select the
optimum transfer mode.
02/18/05
ReVolution User Manual 1.00
Memory Cache
Enabling cache saves time for the CPU by holding data most recently accessed in regular memory (dynamic RAM or
DRAM) in a special storage area of static RAM (SRAM), which is faster. Before accessing regular memory, the CPU
first accesses the cache. If it does not find the data it is looking for there, it accesses regular memory.
Selecting Memory Cache from the Main Menu displays a menu like the one shown here. The actual features
displayed depend on your system's hardware.
Feature
Memory Cache
Cache System BIOS area
Cache Video BIOS area
Cache Base 0-512K:
Cache Base 512k-640k:
Cache Extended Memory Area:
Cache segments, e.g., E800-EFFF
Options
Enabled (Default)
Disabled
Uncached
Write Protect (Default)
Uncached
Write Protect (Default)
Uncached
Write Through
Write Protect
Write Back (Default)
Uncached
Write Through
Write Protect
Write Back (Default)
Uncached
Write Through
Write Protect
Write Back (Default)
Enabled
Disabled (Default)
Write Through
Write Protect
Write Back
Description
Sets the state of the memory cache.
Controls caching of BIOS system.
Controls caching of video BIOS area.
Controls caching of 512k base
memory
Controls caching of 512k – 640k base
memory
Controls caching of system memory
above one megabyte
Controls caching of individual
segments of memory usually reserved
for shadowing system or option
ROMs
WARNING: Incorrect settings can cause your system to malfunction.
Boot Features Menu
Select Boot from the menu bar on the Main Menu.
Use the legend keys to make your selections and exit to the Main Menu.
Use the following chart to select your boot options.
Feature
Boot-time Diagnostic Screen:
Quickboot Mode:
Options
Enabled
Disabled (Default)
Enabled (Default)
Disabled
Description
Display the diagnostic screen during
boot.
Allows the system to skip certain
tests while booting. This will
decrease the time to boot the system.
The BIOS attempts to load the operating system from the disk drives in the sequence selected here. The topmost
item is the first boot device that BIOS will attempt to boot an operating system. If the device is not bootable the BIOS
will move to the next device until a bootable device is found. If no devices are found to be bootable then the BIOS will
post an error message.
ReVolution User Manual 1.00
02/18/05
61
Advanced Menu
Select Advanced from the menu bar on the Main Menu.
Use the legend keys to make your selections and exit to the Main Menu.
Use the following chart to configure the keyboard features:
Feature
Installed O/S
Options
Other
Win95
Win98 (Default)
WinME
Win2000
Reset Configuration Data:
No (Default)
Yes
Large Disk Access Mode:
Other
DOS (Default)
Local Bus IDE adapter:
Disabled (Default)
Primary (Default)
Description
Select the operating system installed
on your system that you will use most
often.
NOTE: An incorrect setting can
cause some operating systems to
display unexpected behavior.
Select “Yes” if you want to clear the
Extended System Configuration Data
(ESCD) area.
UNIX, Novell Netware, or other
operating systems, select ‘Other’. If
you are installing new software and
the drive fails, change this selection
and try again. Different operating
systems require different
representations of drive geometries.
Enable the integrated local bus IDE
adapter
The items in this menu will allow the
user to:
1) Test Mobile features of the
Almador-m Chipset
2) Alter the Reference board
environment.
OEM Platform Advanced Menu
Advanced Chipset Control
I/O Device Configuration
Keyboard Features
Legacy USB Support
Enabled (Default)
Disabled
Enable support for Legacy Universal
Serial Bus.
OEM Platform Advanced Memory Menu
Feature
Platform Power Management SubMenu
Options
Description
These items will control the
various CPU and Chipset Power
Management Features of this
platform
These items will control:
1) Which ACPI Tables will be
include in the RSDT Entry
Table Field.
2) The values stored in specific
ACPI Table Fields.
3) The Enabling of Specific
ACPI Features.
These items determine whether
the integrated PCI Devices will
be enabled in PCI Config. Space
This item allows IDE drives to be
set above ATA 33 if the drive
supports that speed.
ACPI Table/Features Control Sub
Menu
Integrated Devise Control SubMenu
ATA 66/ATA 100 Support
62
Enabled
Disabled
02/18/05
ReVolution User Manual 1.00
Integrated Device Control Sub-Menu
Feature
Options
Description
USB – Device 29
Disabled
Enabled (Default)
USB – Device 29, Function 1
Disabled
Enabled (Default)
USB – Device 29, Function 2
Disabled
Enabled (Default)
AC97 – Device 31, Function 5
Disabled
Enabled (Default)
Enable or Disable all ICH3 USB
1.1 Devices by setting item to the
desired value.
Enable or Disable all ICH3 USB
1.1 Devices by setting item to the
desired value.
Enable or Disable all ICH3 USB
1.1 Devices by setting item to the
desired value.
Enable or Disable the AC97 Audio
Device if present. This Setup Item
will have no effect if an AC97
Audio MDC is not present.
Advanced Chipset Control Menu
Feature
Options
Description
IGD Boot Type
VBIOS Default (Default)
CRT
LCD
CRT_LCD
Select the Video Display that the
Internal Graphics Device will
make active during the POST:
1) VBIOS Default
2) CRT
3) LCD
4) CRT_LCD
IGD – LCD Panel Type
Default Primary Video
Graphics Aperture
Enable Memory Gap
ReVolution User Manual 1.00
800x600
1024x768
LVDS
LVDS (Default)
Selecting “VBIOS Default” will
allow the VBIOS to choose the
Video Display to enable.
Select the LCD Panel used by the
Internal Graphics Device by
selecting the appropriate setup
item. The first item is Panel 1, the
last item is Panel 16. Some
Panels are not numbered due to
size constraints.
NOTE: SVGA screen requires
change to 800x600 LVDS.
Select PCI to use a PCI video
card for the boot display device.
AGP (Default)
PCI
Select AGP to use an AGP video
card for the boot display device.
Select the size of the Graphics
Aperture for the AGP video
device.
32MB
64MB (Default)
128MB
256MB
Disable (Default)
Extended
Free RAM Address space for use
with an option card starting at
15MB.
02/18/05
63
I/O Device Configuration Menu
The CPU communicates with external devices such as printers through devices called Input/Output (I/O) ports such
as serial and parallel ports. These I/O devices require the use of system resources such as I/O addresses and
interrupt lines. If these devices are Plug and Play, either the BIOS can allocate the devices during POST, or the
operating system can do it.
If the I/O devices are not Plug and Play, they may require manually setting them in Setup. On some systems, the
chipset manages the communication devices. Other systems have, instead, a separate I/O chip on the motherboard
for configuring and managing these devices.
Many systems allow you to control the configuration settings for the I/O ports.
Select I/O Device Configuration on the Advanced Menu to display this menu and specify how you want to configure
these I/O Devices:
Use the legend keys to make your selections and exit to the Main Menu.
Use the following chart to configure the Input/Output settings:
Feature
Options
Description
Serial port A:
Serial port B:
Disabled
Enabled (Default)
Auto
OS Controlled
Disabled turns off the port.
Enabled requires you to enter the base
Input/Output address
and the Interrupt number on the next
line.
Auto makes the BIOS configure the
port automatically during
POST.
OS Controlled lets the PnP Operating
System (such as
Windows 95) configure the port after
POST.
Parallel Port:
Disabled
Enabled (Default)
Auto
OS Controlled
Disabled turns off the port.
Enabled requires you to enter the base
Input/Output address
and the Interrupt number below.
Auto makes the BIOS auto configure
the port during POST.
OS Controlled lets the PnP Operating
System (such as
Windows 95) configure the port after
POST.
Mode
Output only
Bi-directional
ECP (Default)
EPP & ECP
Output only is standard one-way
protocol for a parallel
device.
Bi-directional uses two-way protocol of
an Extended
Capabilities Port (ECP).
Floppy Disk Controller
Disabled
Enabled
Auto (Default)
Enables the on-board legacy diskette
controller.
Disabled turns off all legacy diskette
drives.
Auto select per BIOS or OS
Use this menu to specify how the I/O (Input and Output) ports are configured:
x Manually by you.
x Automatically by the BIOS during POST
x Automatically by a PnP Operating System such as Windows 95 after the Operating System boots.
Warning: If you choose the same I/O address or Interrupt for more than one port, the menu displays an asterisk (*) at
the conflicting settings. It also displays this message at the bottom of the menu:
* Indicates a DMA, Interrupt, I/O, or memory resource conflict with another device.
Resolve the conflict by selecting another settings for the devices.
64
02/18/05
ReVolution User Manual 1.00
Keyboard Features
Select Keyboard from the menu bar on the Main Menu.
Use the legend keys to make your selections and exit to the Main Menu.
Use the following chart to configure the keyboard features:
Feature
Numlock
Options
Auto
On
Off (Default)
Enabled
Disabled (Default)
2/sec
6/sec
10/sec
13.3/sec
21.8/sec
26.7/sec
30/sec (Default)
¼ sec
½ sec (Default)
¾ sec
1 sec
Key Click
Keyboard auto-repeat rate
Keyboard auto-lag delay
Description
On or Off turns NumLock on or off
at bootup. Auto turns NumLock on if
it finds a numeric key pad.
Enables key click.
Sets the number of times per second
to repeat a keystroke when you hold
the key down.
Sets the delay time after the key is
held down before it begins to repeat
the keystroke.
Security Menu
Select Security from the menu bar on the Main Menu.
Use the legend keys to make your selections and exit to the Main Menu.
Enabling "Supervisor Password" requires a password for entering Setup. The passwords are not case sensitive.
Pressing  at either Set Supervisor Password or Set User Password displays a dialog box like this:
Set Password
Enter password:
Confirm password: [
Enter: Accept
Type the password and press . Repeat.
Note: In some systems, the User and Supervisor passwords are related; you cannot have a User password without
first creating a Supervisor password. In other systems, you can create and use them independently.
Use the following chart to configure the system-security and anti-virus options.
Feature
Set Supervisor Password
Options
Up to seven alphanumeric
characters
Set User Password
Up to seven alphanumeric
characters
Password on Boot
Enabled
Disabled
Diskette Access
Enabled
Disabled
ReVolution User Manual 1.00
Description
Pressing  displays dialog box for entering
the supervisor password. In related systems, this
password gives full access to Setup menus.
Pressing  displays the dialog box for entering
the user password. In related systems, this password
gives restricted access to SETUP menus.
Enabled requires a password on boot. Requires prior
setting of the Supervisor password. If supervisor
password is set and this option disabled, BIOS
assumes user is booting.
Enabled requires a password to boot from or access
the floppy disk.
02/18/05
65
Boot Menu
Select Boot from the menu bar on the Main Menu.
Use this menu to arrange to specify the priority of the devices from which the BIOS will attempt to boot the Operating
System. The BIOS will attempt first to boot from the CD-ROM drive (the only Removable Device listed). Failing that, it
will attempt to boot from the Primary Master hard disk, and so on down the list.
Removable Devices, Hard Drive, and Network Boot are the generic types of devices on your system from which
you can boot an operating system. You may have more than one device of each type. If so, the generic type is
marked with a plus or minus sign. Use the  key to expand or collapse the devices marked with <+> or <->.
Press  to expand all such devices.
Note: Floppy drives are not managed on this menu as part of Removable Devices. To change a device’s priority on
the list, first select it with the up-or-down arrows, and move it up or down using the <+> and <-> keys. Pressing 
moves a device between the Removable Devices and Hard Drive. Pressing  enables or disables a device.
Feature
Removable Devices
Options
Legacy Floppy Drives
Hard Drive
Toshiba MK6412MAT-(PM)
Bootable Add - Cards
Description
Keys used to view or configure
devices
CD-ROM Drive
Exit Menu
Select Exit from the menu bar on the Main Menu.
The following sections describe each of the options on this menu. Note that  does not exit this menu. You must
select one of the items from the menu or menu bar to exit.
Exit Saving Values
After making your selections on the Setup menus, always select either "Exit Saving Value" or "Save Changes." Both
procedures store the selections displayed in the menus in CMOS (short for "battery-backed CMOS RAM") a special
section of memory that stays on after you turn your system off. The next time you boot your computer, the BIOS
configures your system according to the Setup selections stored in CMOS.
After you save your selections, the program displays this message: Values have been saved to CMOS!
Press  to continue
If you attempt to exit without saving, the program asks if you want to save before exiting.
During bootup, PhoenixBIOS attempts to load the values saved in CMOS. If those values cause the system boot to
fail, reboot and press  to enter Setup. In Setup, you can get the Default Values (as described below) or try to
change the selections that caused the boot to fail.
Exit Discarding Changes
Use this option to exit Setup without storing in CMOS any new selections you may have made. The selections
previously in effect remain in effect.
66
02/18/05
ReVolution User Manual 1.00
Load Setup Defaults
To display the default values for all the Setup menus, select "Load Setup Defaults" from the Main Menu. The program
displays this message:
ROM Default values have been loaded!
Press  to continue
If, during bootup, the BIOS program detects a problem in the integrity of values stored in CMOS, it displays these
messages:
System CMOS checksum bad - run SETUP
Press  to resume,  to Setup
The CMOS values have been corrupted or modified incorrectly, perhaps by an application program that changes data
stored in CMOS. Press  to resume the boot or  to run Setup with the ROM default
values already loaded into the menus. You can make other changes before saving the values to CMOS.
Discard Changes
If, during a Setup Session, you change your mind about changes you have made and have not yet saved the values
to CMOS, you can restore the values you previously saved to CMOS. Selecting “Discard Changes” on the Exit menu
updates all the selections and displays this message:
CMOS values have been loaded!
Press  to continue
Save Changes
Selecting “Save Changes” saves all the selections without exiting Setup. You can return to the other menus if you
want to review and change your selections.
ReVolution User Manual 1.00
02/18/05
67
BIOS Messages
The following is a list of the messages that the BIOS can display. Most of them occur during POST. Some of them
display information about a hardware device, e.g., the amount of memory installed. Others may indicate a problem
with a device, such as the way it has been configured.
Following the list are explanations of the messages and remedies for reported problems. *If your system displays one
of the messages marked below with an asterisk (*), write down the message and contact Kontron Technical Support.
If your system fails after you make changes in the Setup menus, reset the computer, enter Setup and install Setup
defaults or correct the error.
0200 Failure Fixed Disk
Fixed disk is not working or not configured properly. Check to see if fixed disk is attached properly. Run Setup.
Find out if the fixed-disk type is correctly identified.
0210 Stuck key
Stuck key on keyboard.
0211 Keyboard error
Keyboard not working.
*0212 Keyboard Controller Failed
Keyboard controller failed test. May require replacing keyboard controller.
0213 Keyboard locked - Unlock key switch
Unlock the system to proceed.
0220 Monitor type does not match CMOS - Run SETUP
Monitor type not correctly identified in Setup
*0230 Shadow Ram Failed at offset: nnnn
Shadow RAM failed at offset nnnn of the 64k block at which the error was detected.
*0231 System RAM Failed at offset: nnnn
System RAM failed at offset nnnn of in the 64k block at which the error was detected.
*0232 Extended RAM Failed at offset: nnnn Extended memory not working or not configured properly at offset
nnnn.
0250 System battery is dead - Replace and run SETUP
The CMOS clock battery indicator shows the battery is dead. Replace the battery and run Setup to reconfigure the
system. Note: ReVolution’s CMOS battery is rechargeable and should never need replacement.
0251 System CMOS checksum bad - Default configuration used
System CMOS has been corrupted or modified incorrectly, perhaps by an application program that changes data
stored in CMOS. The BIOS installed Default Setup Values. If you do not want these values, enter Setup and enter
your own values. If the error persists, check the system battery or contact KMC.
*0260 System timer error
The timer test failed. Requires repair of system board.
*0270 Real time clock error
Real-Time Clock fails BIOS hardware test. May require board repair.
0271 Check date and time settings
BIOS found date or time out of range and reset the Real-Time Clock. May require setting legal date (1991- 2099).
0280 Previous boot incomplete - Default configuration used
68
02/18/05
ReVolution User Manual 1.00
Previous POST did not complete successfully. POST loads default values and offers to run Setup. If the failure was
caused by incorrect values and they are not corrected, the next boot will likely fail. On systems with control of wait
states, improper Setup settings can also terminate POST and cause this error on the next boot. Run Setup and verify
that the waitstate configuration is correct. This error is cleared the next time the system is booted.
0281 Memory Size found by POST differed from CMOS
Memory size found by POST differed from CMOS.
02B0 Diskette drive A error
02B1 Diskette drive B error
Drive A: or B: is present but fails the BIOS POST diskette tests. Check to see that the drive is defined with the
proper diskette type in Setup and that the diskette drive is attached correctly.
02B2 Incorrect Drive A type - run SETUP
Type of floppy drive A: not correctly identified in Setup.
02B3 Incorrect Drive B type - run SETUP
Type of floppy drive B: not correctly identified in Setup.
02D0 System cache error - Cache disabled
RAM cache failed and BIOS disabled the cache. On older boards, check the cache jumpers. You may have to
replace the cache. See your dealer. A disabled cache slows system performance considerably.
02F0: CPU ID:
CPU socket number for Multi-Processor error.
*02F4: EISA CMOS not writeable
ServerBIOS2 test error: Cannot write to EISA CMOS.
*02F5: DMA Test Failed
ServerBIOS2 test error: Cannot write to extended DMA (Direct Memory Access) registers.
*02F6: Software NMI Failed
ServerBIOS2 test error: Cannot generate software NMI (Non-Maskable Interrupt).
*02F7: Fail-Safe Timer NMI Failed
ServerBIOS2 test error: Fail-Safe Timer takes too long.
device Address Conflict
Address conflict for specified device.
Allocation Error for: device
Run ISA or EISA Configuration Utility to resolve resource conflict for the specified device.
CD ROM Drive
CD ROM Drive identified.
Entering SETUP ...
Starting Setup program
*Failing Bits: nnnn
The hex number nnnn is a map of the bits at the RAM address which failed the memory test. Each 1 (one) in the
map indicates a failed bit. See errors 230, 231, or 232 above for offset address of the failure in System, Extended, or
Shadow memory.
Fixed Disk n
Fixed disk n (0-3) identified.
Invalid System Configuration Data
Problem with NVRAM (CMOS) data.
I/O device IRQ conflict
ReVolution User Manual 1.00
02/18/05
69
I/O device IRQ conflict error.
PS/2 Mouse Boot Summary Screen:
PS/2 Mouse installed.
nnnn kB Extended RAM Passed
Where nnnn is the amount of RAM in kilobytes successfully tested.
nnnn Cache SRAM Passed
Where nnnn is the amount of system cache in kilobytes successfully tested.
nnnn kB Shadow RAM Passed
Where nnnn is the amount of shadow RAM in kilobytes successfully tested.
nnnn kB System RAM Passed
Where nnnn is the amount of system RAM in kilobytes successfully tested.
One or more I2O Block Storage Devices were excluded from the Setup Boot Menu
There was not enough room in the IPL table to display all installed I2O block-storage devices.
Operating system not found
Operating system cannot be located on either drive A: or drive C:. Enter Setup and see if fixed disk and drive A: are
properly identified.
*Parity Check 1 nnnn
Parity error found in the system bus. BIOS attempts to locate the address and display it on the screen. If it cannot
locate the address, it displays ????. Parity is a method for checking errors in binary data. A parity error indicates
that some data has been corrupted.
*Parity Check 2 nnnn
Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate
the address, it displays ????.
Press  to resume,  to Setup,  for previous
Displayed after any recoverable error message. Press  to start the boot process or  to enter Setup and
change the settings. Press  to display the previous screen (usually an initialization error of an Option ROM,
i.e., an add-on card). Write down and follow the information shown on the screen.
Press  to enter Setup
Optional message displayed during POST. Can be turned off in Setup.
PS/2 Mouse:
PS/2 mouse identified.
Run the I2O Configuration Utility
One or more unclaimed block storage devices have the Configuration Request bit set in the LCT. Run an I2O
Configuration Utility (e.g. the SAC utility).
System BIOS shadowed
System BIOS copied to shadow RAM.
UMB upper limit segment address: nnnn
Displays the address nnnn of the upper limit of Upper Memory Blocks, indicating released segments of the BIOS
which can be reclaimed by a virtual memory manager.
Video BIOS shadowed
Video BIOS successfully copied to shadow RAM.
70
02/18/05
ReVolution User Manual 1.00
Test Points and Beep Codes
At the beginning of each POST routine, the BIOS outputs the test point error code to I/O address 80h. Use this code
during trouble shooting to establish at what point the system failed and what routine was being performed. The
following is a list of the checkpoint codes written at the start of each test and the beep codes issued for terminal
errors. Unless otherwise noted, these codes are valid for PhoenixBIOS 4.0 Release 6.x.
Code
02h
03h
04h
06h
07h
08h
09h
0Ah
0Bh
0Ch
0Eh
0Fh
10h
11h
12h
13h
14h
16h
17h
18h
1Ah
1Ch
20h
22h
24h
28h
29h
2Ah
2Ch
2Eh
2Fh
32h
33h
36h
38h
3Ah
3Ch
3Dh
41h
42h
45h
46h
47h
48h
49h
4Ah
4Bh
4Ch
4Eh
4Fh
Beeps
1-2-2-3
1-3-1-1
1-3-1-3
1-3-4-1
1-3-4-3
2-1-2-3
Description
Verify Real Mode
Disable Non-Maskable Interrupt (NMI)
Get CPU type
Initialize system hardware
Disable shadow and execute code from the ROM.
Initialize chipset with initial POST values
Set IN POST flag
Initialize CPU registers
Enable CPU cache
Initialize caches to initial POST values
Initialize I/O component
Initialize the local bus IDE
Initialize Power Management
Load alternate registers with initial POST values
Restore CPU control word during warm boot
Initialize PCI Bus Mastering devices
Initialize keyboard controller
BIOS ROM checksum
Initialize cache before memory Auto size
8254 timer initialization
8237 DMA controller initialization
Reset Programmable Interrupt Controller
Test DRAM refresh
Test 8742 Keyboard Controller
Set ES segment register to 4 GB
Auto size DRAM
Initialize POST Memory Manager
Clear 512 kB base RAM
RAM failure on address line xxxx*
RAM failure on data bits xxxx* of low byte of memory bus
Enable cache before system BIOS shadow
Test CPU bus-clock frequency
Initialize Phoenix Dispatch Manager
Warm start shut down
Shadow system BIOS ROM
Auto size cache
Advanced configuration of chipset registers
Load alternate registers with CMOS values
Initialize extended memory for RomPilot
Initialize interrupt vectors
POST device initialization
Check ROM copyright notice
Initialize I20 support
Check video configuration against CMOS
Initialize PCI bus and devices
Initialize all video adapters in system
QuietBoot start (optional)
Shadow video BIOS ROM
Display BIOS copyright notice
Initialize MultiBoot
ReVolution User Manual 1.00
02/18/05
71
50h
51h
52h
54h
55h
58h
59h
5Ah
5Bh
5Ch
60h
62h
64h
66h
67h
68h
69h
6Ah
6Bh
6Ch
6Eh
70h
72h
76h
7Ch
7Dh
7Eh
80h
81h
82h
83h
84h
85h
86h
87h
88h
89h
8Ah
8Bh
8Ch
8Fh
90h
91h
92h
93h
95h
96h
97h
98h
99h
9Ah
9Ch
9Dh
9Eh
9Fh
A0h
A2h
A4h
72
2-2-3-1
1-2
Display CPU type and speed
Initialize EISA board
Test keyboard
Set key click if enabled
Enable USB devices
Test for unexpected interrupts
Initialize POST display service
Display prompt "Press F2 to enter SETUP"
Disable CPU cache
Test RAM between 512 and 640 kB
Test extended memory
Test extended memory address lines
Jump to UserPatch1
Configure advanced cache registers
Initialize Multi Processor APIC
Enable external and CPU caches
Setup System Management Mode (SMM) area
Display external L2 cache size
Load custom defaults (optional)
Display shadow-area message
Display possible high address for UMB recovery
Display error messages
Check for configuration errors
Check for keyboard errors
Set up hardware interrupt vectors
Initialize Intelligent System Monitoring
Initialize coprocessor if present
Disable onboard Super I/O ports and IRQs
Late POST device initialization
Detect and install external RS232 ports
Configure non-MCD IDE controllers
Detect and install external parallel ports
Initialize PC-compatible PnP ISA devices
Re-initialize onboard I/O ports.
Configure Motherboard Configurable Devices (optional)
Initialize BIOS Data Area
Enable Non-Maskable Interrupts (NMIs)
Initialize Extended BIOS Data Area
Test and initialize PS/2 mouse
Initialize floppy controller
Determine number of ATA drives (optional)
Initialize hard-disk controllers
Initialize local-bus hard-disk controllers
Jump to UserPatch2
Build MPTABLE for multi-processor boards
Install CD ROM for boot
Clear huge ES segment register
Fix up Multi Processor table
Search for option ROMs. One long, two short beeps on checksum failure
Check for SMART Drive (optional)
Shadow option ROMs
Set up Power Management
Initialize security engine (optional)
Enable hardware interrupts
Determine number of ATA and SCSI drives
Set time of day
Check key lock
Initialize typematic rate
02/18/05
ReVolution User Manual 1.00
A8h
AAh
ACh
AEh
B0h
B1h
B2h
B4h
B5h
B6h
B7h
B9h
BAh
BBh
BCh
BDh
BEh
BFh
C0h
C1h
C2h
C3h
C4h
C5h
C6h
C7h
C8h
C9h
CAh
CBh
CCh
CDh
CEh
D2h
E0h
E1h
E2h
E3h
E4h
E5h
E6h
E7h
E8h
E9h
EAh
EBh
ECh
EDh
EEh
EFh
F0h
F1h
F2h
F3h
F4h
F5h
Erase F2 prompt
Scan for F2 key stroke
Enter SETUP
Clear Boot flag
Check for errors
Inform RomPilot about the end of POST.
POST done - prepare to boot operating system
One short beep before boot
Terminate QuietBoot (optional)
Check password (optional)
Initialize ACPI BIOS
Prepare Boot
Initialize SMBIOS
Initialize PnP Option ROMs
Clear parity checkers
Display MultiBoot menu
Clear screen (optional)
Check virus and backup reminders
Try to boot with INT 19
Initialize POST Error Manager (PEM)
Initialize error logging
Initialize error display function
Initialize system error handler
PnPnd dual CMOS (optional)
Initialize note dock (optional)
Initialize note dock late
Force check (optional)
Extended checksum (optional)
Redirect Int 15h to enable remote keyboard
Redirect Int 13h to Memory Technologies Devices such as ROM, RAM, PCMCIA, and
serial disk
Redirect Int 10h to enable remote serial video
Re-map I/O and memory for PCMCIA
Initialize digitizer and display message
Unknown interrupt
The following are for boot block in Flash ROM
Initialize the chipset
Initialize the bridge
Initialize the CPU
Initialize system timer
Initialize system I/O
Check force recovery boot
Checksum BIOS ROM
Go to BIOS
Set Huge Segment
Initialize Multi Processor
Initialize OEM special code
Initialize PIC and DMA
Initialize Memory type
Initialize Memory size
Shadow Boot Block
System memory test
Initialize interrupt vectors
Initialize Run Time Clock
Initialize video
Initialize System Management Manager
Output one beep
Clear Huge Segment
ReVolution User Manual 1.00
02/18/05
73
F6h
F7h
74
Boot to Mini DOS
Boot to Full DOS
02/18/05
ReVolution User Manual 1.00
Customer Service
This section provides contact information should you need technical support for your system, or need to return
merchandise.
Technical Support
If you should encounter difficulties with your application or with this product, or need guidance on setting up your
system, we are ready to assist you. Please contact our Technical Support department at the following locations:
USA:
Technical Support hours are: 7:00AM to 6:00PM – Monday – Friday
TEL:
(888) 343-5396 (Toll free in US and Canada)
(952) 974-7200
FAX:
(952) 949-2791
E-mail: support@kontronmobile.com
Europe, Middle East, Africa:
TEL:
FAX:
E-mail:
(+49) 8165-77 112
(+49) 8165-77 110
techsup@kontron.com
Kontron Asia (except China):
TEL:
FAX:
011-886-2-2910-3532
011-886-2-2910-3482
Sales Contact:
E-mail: sales@kontron-asia.com
Technical Support Contact:
E-mail: support@kontron-asia.com
Kontron China:
TEL:
FAX:
E-mail:
+86 21 5426 1660
+86 21 5426 1650
FAE@kontron.com.cn
Technical Support Contact:
E-mail: FAE@kontron.com.cn
When you call, make sure to have the following information on hand:
x unit part number (P/No #),
x serial number (S/No #) of the defective unit (found on the back of the unit).
Then, explain the nature of your problem to the service technician.
If you have any questions about Kontron Mobile Computing, or our products and services, you may reach us at the
aforementioned telephone numbers, by e-mail, or by writing to:
Kontron Mobile Computing Inc.
7631 Anagram Drive
Eden Prairie, MN 55344 USA
ReVolution User Manual 1.00
02/18/05
75
Returning Defective Merchandise
Before returning any merchandise, please follow these instructions:
1. In the USA / North America, contact:
KMC Technical Support
Technical Support hours are: 7:00AM to 6:00PM – Monday – Friday
TEL: (888) 343-5396 (Toll free in US and Canada)
(952) 974-7200
FAX: (952) 949-2791
E-mail: support@kontronmobile.com
In Europe:
Contact our Service Department and request an
RMA # (Return Material Authorization) by:
Fax: (+49) 8165-77 331
E-mail: service@kontron.com
In Asia:
Contact your sales representative and request an
RMA # (Return Material Authorization) by:
FAX: 011-886-2-2910-3482
E-mail: sales@kontron-asia.com
In China:
Contact your sales representative and request an
RMA # (Return Material Authorization) by:
FAX: +86 21 5426 1650
E-mail: FAE@kontron.com.cn
2.
Make sure that you receive a RMA # from Kontron-Service before returning any merchandise. Clearly write or
mark this number on the outside of the package you are returning.
3. Include the name and telephone number of a person whom we can contact for further explanations if necessary
when returning goods. Where applicable, always include all duty papers and invoice(s) associated with the
item(s) in question.
4. Ensure that the unit is packed in its original box, if available, or packed to avoid shipping damage.
5. Include a copy of the RMA form and problem description.
76
02/18/05
ReVolution User Manual 1.00
©2002 Kontron Mobile Computing Inc.
Kontron Mobile Computing
7631 Anagram Drive
Eden Prairie, MN 55344-7310 USA
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2005:02:18 18:50:29+08:00
Modify Date                     : 2005:02:18 18:50:29+08:00
Page Count                      : 85
Creation Date                   : 2005:02:18 10:50:29Z
Mod Date                        : 2005:02:18 10:50:29Z
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : amanda
Metadata Date                   : 2005:02:18 10:50:29Z
Creator                         : amanda
Title                           : plus UserMan.pdf
EXIF Metadata provided by EXIF.tools
FCC ID Filing: Q7KREVOLUTION-V5

Navigation menu