Korea Data Systems Co KD-1511 User Manual 8
Korea Data Systems Co Ltd 8
8
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 70159 |
| Application ID | GfECwcdmCL/25rmnuop6Mg== |
| Document Description | 8 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 22.23kB (277832 bits) |
| Date Submitted | 1999-11-16 00:00:00 |
| Date Available | 1998-09-18 00:00:00 |
| Creation Date | 2001-05-15 22:43:14 |
| Producing Software | Acrobat Distiller 4.0 for Windows |
| Document Lastmod | 2001-05-15 22:43:14 |
| Document Title | 8 |
APPENDIX C:
USER’S MANUAL
¢
Operation & Installation Guide
MODEL NO. : KD-1511
15" Multi-Scan Color Monitor
(13.8"dfag. Viewing area)
FCC Compliance Statement
EH
Safety Instructions
Introduction
Product Package
Setup
Controls and Adiustments
Timing Guide
oomwN-a
Specifications
FCC Compliance Statement
Note:
This equipment has been tested and found to comply with the limits
for a Class 8 digital device, pursuant to Part 150i FCC Rules, These
limits are deSigned to provide reasonable protection against harmful
interference in a residential installation, This equipment generates,
uses. and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However. there is no guarantee
that interference will not occur in a particular installation If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equrpment off and
on, the user is encouraged to try to correcr the interference by one or
more of the followmg measures:
- Reorient or relocate the receiving antenna
- increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
— Consult the dealer or an experienced radio/televiSion
technician for help.
Notice 1:
responsible for compliance could void the user‘s authority to operate
the equipment
Notice 2:
Shielded interface cables, if any, must be used in order to comply with
the emisSion limits
DOC CLASS B NOTICE
This digital apparatus does not exceed Class B limits for radio noise
emission for a digital apparatus as set out in the Radio Interference
Regulations of the Canadian Department of Communications
“
Safety Instructions
l .
2.
10.
Read these instructions Save these instructions for later use.
Follow all warnings and instructions marked on the product.
Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
Do not use this product near water,
Do not place this product on an unstable cart, stand, or table. The
product may lall, causmg serious damage to the product
Slots and openings in the cabinet and the back or bottom are
provided for ventilation;to ensure reliable operation of the product
and to protect it from overheating, these openings must not be
blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface.
This product should never be placed near or over a radiator or heat
register, or in a built in installation unless proper ventilation is
provided
Thls product should be operated from the type of power indicated
on the marking label lf you are not sure of the type of power
available, consult your dealer or local power company.
Do not allow anything to rest on the power cord Do not locate
this product where persons will walk on the cord.
If an extension cord is used with this product, make sure that the
total of the ampere ratings on the products plugged into the
extension cord does not exceed the extension cord ampere rating.
Also make sure that the total of all products plugged into the wall
outlet does not exceed 15 amperes
Never push objects ol any kind into this product through cabinet
slots as they may touch dangerous voltage points or short out
parts that could result in a risk of fire or electric shock. Never
spill liquid of any kind on the product
III
ll
Safety lnstructions
ll Do not attempt to service this product yourself, as opening or
, removmg covers may expose you to dangerous voltage points or
' other risks. Refer all servicing to servrce personnel.
12. Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b If liquid has been spilled into the product.
c, If the product has been exposed to rain or water.
, If the product does not operate normally when the operating
instructions are followed. Adjust only those controls that are
covered by the operating instructions Since improper adjust-
ment of other controls may result in damage and will otten
require extensrve work by a qualified technician to restore the
product to normal operation.
e. if the product has been dropped or the cabinet has been
damaged.
13 Use only the proper type of power supply cord set (provided in
your manual accessories box) for this unit, it should be a
detachable type:UL listed/GSA certified, type SVT/SJT, rated as
10A 125V minimum, VDE approved or its equivalent
14 The Socket-Outlet is to be installed near the equipment and is
easily accessible
COLOR CONTROL
5500 K
5500 K usen
E! _:1 55W-
E] —:1 557°
E] —:l 55“!-
o/er SELECT
e: ENTER
®~ RETURN
IV
Introduction
ll General information
Congratulations on selecting lhls high resolution multi—scan color
monitor.
This high performance display contains the latest technology of flat
screen design and micro-processor control. This monitor has been
equipped with both automatic and manual adjustments,
The automatic controls are factory preset and feature automatic
factory frequency scanning,
The manual controls feature use digital adjustments to personalize
the display in various applications.
The ergonomic characteristics of the antiglare flat screen, high
refresh rates, and tilt swrvel base allow comfortable usage when
2. Features
- ls'antiglare, flat screen, high-contrast picture tube.
- 0.28mm dot pitch
0 IBM compatible
0 Multi-scan .' horizontal frequencies 30‘70khz, vertical
frequencies 50—140hz.
- Universal auto—switching power supply,
- Power management
0 Digital controls for Sizing & distortion
- DDC 28
Product Package
Determine the most convenient location for your monitor.
Make sure that you have enough room to install cables and
connect the monitor to the system and power Supply.
Open the shipping carton and check the contents of the package
The package should include the following items:
- 15" Color Monitor
~ Power Cord
- Owner's Manual
Note If any llem(s) are l’l’llSSing or damaged, Contact your dealer
immediately
2, Remove the monitor from its shipping carton (see figure 1).
Save the carton and packaging materials in case you need to
relocate the monitor.
Figure l
Setup 5"
Setting Up your monitor is easy All you have to do is make a
few simple connections and adiustments The procedure is as
follows.
1. Start up
Switch the power off to both your monitor and computer. The T
location of the power swnch is on the lower right hand corner
of the monitor
2. Power cable Connection.
Connect the female end of the power cable to the power
input on the back of the monitor, Next, plug the male cable to
the wall outlet for power.
To power input of monitor
E? 2 hit; Q I]
To AC outlet
lzmtltil
To PC inlet
Figure?
3. Signal cable connection
Connect the 15 pin signal cable to the PC
Lock both screws to ensure that the monitor is properly grounded,
M “4-3-
PlN NO, DESCRlPTlON PIN NO DESCRlPTION
‘l Video red 9 N. C
2. Videojieen Wround
3.Viceo blue Tune
l" A N c 12. SDA
5. DDC Return 13. Hor-S m:
D we 15an comm” 6. Video red ground M Ver< ric
“W3 7. Video reen round 15. S L
8 Video blue §round
3 , (
Setup
4. Power on
Switch on the power to borh your monitor and computer.
5 Adjusting the Picture
A djust the controls. if necessary, to get the best picture.
A description of the functions of the controls may be found in
the next section
6. Adjusting the Tilt-Swivel Base
The tilt~swrvel base can be adjusted for your maxrmurn
viewing comfort, it can be adjusted through angles of 90“
horizontally and 16" vertically.
5' i1-
90.
Note:
Due to the sensitivity of this monitor to earth's magnetic
field. you may experience minor irregularities in the display if
you swivel the monitor through more than 90‘ while the
monitor is ON. If such behavror occurs, please turn the monitor
OFF and ON again‘ The display should return to normal
7. Setup ofthe Video Circuitry
To use the full potential of this product it is necessary to
first set the Video circuitry of the computer according to the
maximum capabilities of this monitor.
This can be expressed in any of the following ways;
-1280 x 1024 Nl
-1280 x 1024, BOHZ
41024 x 768, 76HZ
x»
—
Controls and Adiustments
i There are a few swrtches that are located on your monitorr
The power indicator and adiustable controls allow the user to
maximize the display ior individual preferencesr
The description of these functions are as follows :
Front Panel Controls
DIGlTAL CONTROL PANEL
Figure 5
1. Power ON/OFF Switch
Press this button to turn the power ON (1) Press it once
again to turn the power OFF (0). There will be a two second delay lor
the monitor to come on
2. Power Indicator
This indicator should be on when the power is switched ON. If
r not. check the power cord to see if is properly connectedr
i MODE 1 ON STAND BY l; SUSPEND OFF
Green/Blink Green/Blink Greemlink
Power Indmtor Green 1 Osec 1.0 sec 2.05ec
Controls and Adjustments
Digital Control Panel
Then, these adjusted settings are kept in memory even if you change
resolution or turn off the monitor.
0®®
EXlT/ DOWN up ENTER
DEGAUSS
KEY FUNCTION
1. ENTER @
Press this key to display the main monitor menu.
Press this key again to select a particular sub-menu
2. EXIT/DEGAUSS ®
EXIT
Press this key to close rhe main monitor menu.
DEGAUSS
Press this key degauss your monitor.
3. DOWN/UPG) (9
When the main menu is displayed, use these buttons to select the
menu you want.
_%:
Controls and Adiustments
ON SCREEN CONTROL ON SCREEN mot.
fig CONTRAST a
9/9 : SELECT
E 9 : ENTER Q
Q E
ED @
El El
WZA x m @75Hx
Primate Exit
Fmfi'mKHz 51:75“:
Press 8 To Exit
Menu Descriptions
1. CONTRAST 0
Selecting this function allows you to make adjustments to the black
level of the display screen
2. BRIGH’TNESS {c}:-
Selecting this function allows you to make adiustments to the luminosity
level of the display screen.
3. H — POSITlONlHORlZONTAL POSITION) [3
Select this function, then use the + and - buttons to center the image
horizontally on the display screen.
4. H-SIZEtHOHlZONTALSlZE) 8
Select this function, then use the + and » buttons to expand or
decrease the image width to horizontally fill the display screen.
5. V—POSITIONNERT'ICAL POSmON) 8
Select this function, then use the + and - buttons to center the image
vertically on the display screen.
6. V-SlZElVERTlCALSlZE) CD
Select this function, then use the + and - buttons to expand or
decrease the image height to vertically flll the disply screen.
7. SlDE-PINtCUSHIONl M
select this function, then use the + and v buttons to straighten the
sides of the image by pulling them in opposing directions
ii
Controls and Adjustments
a. PIN BALANCE
Select this control, then use the + and - buttons to straighten the
srdes of the image by pulling them in the corresponding direction
9. CORNER PIN
Select this control, then use the + and - buttons to straighten the top
and bottom corners of the image by pulling them in opposing
direction)
10.TRAPEZOID (5;
Select this control, then use + and - buttons to even the widths of
the top and bottom of the display (pulling the sides in opposing
directions)
11.PARALLELOGRAM Q)
Select this control, then use the + and - buttons to center the top and
bottom of the display (pulling the sides in the corresponding
direction)
12.ROTATION @
Select this control, then use the + and - buttons to rotate the image
until sides ol the image are parallel to the edge of the bezel.
13. COLOR CONTROL
Select this control, then use the + end - buttons to scroll to the
desired temperature. Use the button to select either the 9300“
K, 6500” K , 5500“ K or user fora custom HGE setting
144 050 POSITION
Select the function, then use the + and - buttons to move OSD
window horizontally or vertically
15. RECALL El
Select this function, then press and hold the ._l button, contmue to
depress this button until the progress bar disappears.
—
Tlming Guide
The 15" color monitor rs a Digital multr—scan monitor. It operates
at horizontal frequencies of anywhere between 30 KHz and 70 KHz.
Because of its microprocessorvbased design, it offers
auto-synchronization and auto-sizing capabilities. At the preset
status, this monitor otters 11 pre-programmed settings for more
common graphics standards. They are listed in the table below.
h Preset Resolufion “Tm H F’WWVIL Polarity Interlaced
M1 640x480/VGA 315 so -/- N
M2 720x400/VGA 31.5 70 -/+ N
l M3 640x480/VGA 37.5 75 -/~ EE
M4 540x480/VGA 433 as j -/- N
M5 SOOXGOONESA 46.9 75 +/+ N
M6 102A><7es7MAg_k 497—1 75 -/- N
M7 800x600/VESA 53,7 85 +/ + N
MB lOZ4x768/VESA-l 50.0 75 + / + N
M9 1280x1024/VESA 54.0 50 +/+ N
M10 1152x864/VESA 67.5 75 +/+ —N_—1
M11 1024X7GSIVESA 68.7 as +/+ L N
- ln ifldl‘lfifl to H factory modes, there are 6 additional user modes
1! more than 6 modes are inputted, it Will he uvernded rn accordance wrtn sawing
order of additional modes
Specifications
h 15- diagonal, 0.28mm dot pitch, 90
degree deflection non—glare etched
P'ere tube screen, tinted glass, medium-short
persistence phosphor.
Resolution 1280 X 1024 addressable
1024 x 768 physical
Wdeo input Analog, posrtive going
signall0.7V p-p)
Horizontal input
TTLt positive or negative
90an pulsel2.4~5v pp)
Vertical input
TTTL, posrtive or negative
gomg puise(2,4—5V pp)
Scan frequency
Horizontal: 30~ 70KHz
Vertical: 50~l40Hz
Standard display area
TZSOmmlH) x ‘lSSrnmlvl/
10.23'lH) x 7t67'lV)
Display color
Unlimited
L Power input
F100~240V AC. SO/GOHZ
‘ Fuse rating
250V. 3 3 DAlUL, CSA, TUV) or T 3.15AlTUV)
Power consumption
TOn : Less than 80W
‘ Stand by : Less than 15W
Suspend : Less than 15W
‘ Off ' Less than BW
Operating 0 To 40 Degree C.
temperature A
366mleV) X 382mmlH)
Dimensions x 408mmlDll
( ‘ 14t4'(W)X14 B'lH) X 18.0"(Dl
f Weight l 13,2Kglnetl/29 98lbs
lO
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2001:05:15 22:43:14 Producer : Acrobat Distiller 4.0 for Windows Modify Date : 2001:05:15 22:43:14-04:00 Page Count : 16EXIF Metadata provided by EXIF.tools