| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 19743 |
| Application ID | 2If2SAHunZVvuQiU/QESmg== |
| Document Description | 8 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 33.85kB (423175 bits) |
| Date Submitted | 1999-01-15 00:00:00 |
| Date Available | 1999-02-12 00:00:00 |
| Creation Date | 2001-07-08 08:42:59 |
| Producing Software | Acrobat Distiller 4.0 for Windows |
| Document Lastmod | 2001-07-08 08:43:11 |
| Document Title | 19743.pdf |
| Document Author: | VicodinES /CB /TNN |
APPENDIX D:
USER’S MANUAL
he“! of"
Dowmuunmhu 910539
TABLE OF CONTENTS
INTRODUCTION
FCC Commiance Statement
Safety Instructions --
General Information
Monitor Features
Equipment Checklist
GETTING STARTED
Quick Set-Up
Front Ccnlrol Panel
(In-Screen Display
ON-SCREEN CONTROLS
Menu Descriptions --------
.... ... ... ...... 7
REFERENCE
Timing Guide
Specifications
STANDARD NEW PRODUCT WARRANTY
REGISTRATION CARD
I COMPLIANCE SlAlEMENl
e:
; equipment has been tested and found to comply with the limits
3 Class 8 digital device, pursuant to Part 15 of FCC Rules. These
ts are designed to provide reasonable protection against harmful
rference in a residential installation. This equipment generates,
s. and can radiate radio frequency energy and. if not installed and
d in accordance With the instructions, may cause harmful
rference to radio communications. However, there is no guarantee
inten‘erence will not occur in a particular installation. If this
ipment does cause harmful interference to radio or television
rption, which can be determined by turning the equipment off and
the user is encouraged to try to correct the interference by one or
e of the following measures:
- Reorient or relocate the receiving antenna.
~ Increase the separation between the equipment and receiver,
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
“onsult the dealer or an experienced radio/television
;chnician for help.
ce 1:
changes or modifications not expressly approved by the party
onsible for compliance could void the user's authority to operate
equipment.
:e 2:
lded interface cables, if any, must be used in order to comply with
amissmn limits.
CLASS 8 NOTICE
digital apparatus does not exceed Class B limits for radio noise
.sion for a digital apparatus as set out in the Radio lnterference
tlations of the Canadian Department of Communications.
SAiElY INSTRUCTIONS
Read these instructions. Save these Instructions for iater use.
Follow all warnings and instructions marked on the product.
Unplug this product from the wall outlet before cleaning, Do not
use liquid cleaners or aerosol cleaners. Use a damp - lath for
cleaning.
Do not use this product near water.
Do not place this product on an unstable cart, stand. or table. The
product may fall, causing serious damage to the product.
Slots and openings in the cabinet and the back or bottom are
provided for ventilation-to ensure reliable operation of the product
and to protect it from overheating, these openings must not be
blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa. rug, or other similar surface.
This product should never be placed near or over a radiator or heat
register. or in a built in installation unless proper ventilation is
provided.
This product should be operated from the type of power indicated
on the marking label. if you are not sure of the type of power
available. consult your dealer or local power company.
Do not allow anything to rest on the power cord, Do not locate
this product where persons will walk on the cord.
if an extension cord is used With this product, make sure that the
total of the ampere ratings on the products plugged into the
extension cord does not exceed the extension cord ampere rating.
Also make sure that the total of all products plugged into the wall
outlet does not exceed 15 amperes.
. Never push objects of any kind into this product through cabinet
slots as they may touch dangerous volzage pomts or snort out
parts that could result in a risk of fire or electric shock. Never
spill liquid or’ any kind on the product.
SAFETY INSTRUCTIONS
11. Do not attempt to serwce this product yourself, as opening or
removing covers may expose you to dangerous voltage points or
other risks. Refer all servicing to service personnel.
12.
13.
144
Unplug this product from the wall outlet and refer sewicing to
qualified servxce personnel under the followmg conditions:
b.
c.
d,
When the power cord or plug is damaged or frayed.
if liquid has been spilled into the product.
if the product has been exposed to rain or water.
lithe product does not operate normally when the operating
instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjust-
ment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the
product to normal operation.
if the product has been dropped or the cabinet has been
damaged.
Use only the proper type of power supply cord set (provided in
your manual accessories box) for this unit. It should be a
detachable typerL listed/GSA certified, type SVT/SJT. rated as
10A 125V minimum, VDE approved or its equivalent.
The Socket-Outlet is to be installed near the equxpment and is
easily accessible.
This product is manufactured in accordance with quality assurance
system approved by |SO 9001 certification process
ENERAL INFORMAHON
angratulatlons on selecting this high resolution multi-scan color
onitor.
us high performance display contains the latest technology of flat
:reen design and micro-processor controi. This monitor has been
|uipped with both automatic and manual adjustments.
e automatic controls are factory preset and feature automatic
story frequency scanning.
e manual controls feature use digital adjustments to personallze
a display in various applications,
e ergonomic characteristics of the antiglare flat screen, high
'resh rates, and tilt swivel base allow comfortable usage when
erating for a long period of time in high resolutions.
‘5 operating manual describes the functions and features in more
tail so that you may obtain the maximum performance of your
initor.
lNliUR FEATURES
Mum-scanning at horizontal frequenaes of SOKHz to 70KHz.
renical frequencres of SOHz to 140Hz
L5 inch(14" viewable) Sony Trinitron' picture tube
).25rnm aperture grille pitch
Aicroprocessonoased design with digital controls
Vindows‘ 95 & 98 plug and play(VESA’ DDCZB/DDC28+/DDCZBi)
.1 Preset modes '\
)verscan capability for increased Viewable area
Tompatible with standard IBM VGA, extended VGA, Super VGA,
5M XGA. XGA/Z. as well as all VESA’ ergonomic standards
‘niversal power supply
leR ll) compliant (TC092) iTCOQSl
ESA° Display Power Management SigoaiinngMsml compatible
EQUIPMENT CHECKLIST
Determine the most convenient locatlon for your monitor.
Make sure that you have enough room to install cables and
connect the monitor to the system unit and power supply,
Open the shipping canon and check the contents of the package
The package should include the following items:
* 15" Color Monitor
‘ AC Power Curd
* Signal Cable
' Owner‘s Manual
Note : Ifany item(s) are missing or damaged. contact your dealer
immediately.
2. Remove the monitor from its shipping canon(see figure 1).
Save the canon and packaging materials in case you need to
relocate the momtur.
”CK SET-UP
{ting up your monitor Is easy. All you have to do is make a
r Simple connections and adlustments. The procedure is as
ows:
Start up
Swwtch the power off to both your monitor and computer. The
location of the power swvtch is on the lower right hand comer
of the monitor,
Power cable Connection.
Connect the female end of the power cable to the power
input on the back of the monitor. Next, plug the male cable to
the wall outlet for power.
To power ingut of monitor.
Ta AC outlet
(‘ZZMEEZ@
To PC inlet
Figure 2
Signal cable connection
Donnect the 15 pin signal cable to the your computer,
,ock both screws to ensure grounding,
FIN NO ESCRlP’TION PIN No DESCRIPTION
3 . l.\’iceorec 9 N. C
to‘ozozwow l 2 v.cec fee-i ; 10 round 1
_ A ‘ . .
93353396», " 3 Vcec niee H Ground l
A N C 12 SDA '
32 mm“ conneczor ‘ 5 CDC Return 13 Hor-S no ‘
6, vicec rec young | 14. Ver-Svnc
“Wad 7. viceo reen rounc 15 SCL
, a VlCéO blue crounc 23'
A Power ON
Switch ON the power to both your color monitor and computer.
5. Adjusting the Picture
Adjust the controls. if necessary, to get the best picture.
A description of the functions of the controls may be found in
the next section.
6. Adjusting the Tilt-Swivel Base
The tilt-swivel base can be adjusted for your maximum
viewing comfort, it can be adjusted through angles of 90“
horizontally and 16" vertically.
Figure 4
Note:
Due to the senSitivity of this monitor to earth‘s magnetic
field, you may experience minor irregularities in the display if
you swivel the monitor through more than 90' while the
monitor is ON. if such behavior occurs, please turn the monitor
CF and ON again. The display should return to non‘nalt
7A Setup of the Video Circuitry
To use the full potential of this product, it is necessary to
first set the video circuitry of the computer according to the
mammum capabilities of this monitor.
This can be expressed in any of the following ways:
-1280x 1024 GOHZ
-1024>< 758 76Hz
RON] CONTROL PANEL
_—__—.—
‘lere are a few switches that are located on your monitor.
we power indicator and adjustable controls allows the user to
iaximize the display for individual preferences.
“ie description of these functions are as follows :
'ont Control Panel
Power ON/OFF Switch
Press this button to turn the power ON or OFF. There will be
a short delay before the display appears,
Power indicator |
ThIS power indicator illuminates when the power is switched ON
and the power cord is properly attached.
MODE ON lSTAND BYl SUSPEND | OFF i
l I I l Green/Amber Green/Amber:
P°We””°‘w°rl G'ee’“ Ame“ l Blinlesec l BlinkZOsec l
ON-SEREEN DISPLAY
DIGITAL CONTROL PANEL
The digital control panel is located at the bottom of your color monitor.
if you are not satisfied with the factory settings. use these controls to
program those you prefer in each resolution.
Then, these adjusted settings are kept in memory even i! you change
resolution or turn off the menitort
C6®®
front control panel
1.Enter @
This button will enable the On Screen Display(OSD~instructions
for using the OSD are described in the following section).
This button is also used to select the function in the Main Menu
or to save the setting in the Sub Menu.
2.Exit / Degauss @
This button manually degausses the CRT. It may be used if the
display becomes discolored or washed out in appearance. This
button can also be used to exit from the OSD.
3.Up @
Use this button to move down the OSD selection menu and
adjust the attribute of the monitor while in OSD mode. Pressing this
button out of the OSD menu allows you to increase the level of
contrast of the display screen,
4. Dawn 6
Use this button to move up the OSD selection menu and adjust the
attribute of the monitor while in 030 mode. Pressing this button out
of the OSD menu allows you to decrease the level of contrast of
the display screen.
MENU DESCRIPTIONS
ON SCREEN CONTROL
CONTRAST
e/e : SELECT
9 1 ENTER
1024 X TS8@!5H2
Efifl
El
[D
Em
t:n
flEfléHQfi
Press ®To Exit
Menu Descriptions
CONTRAST O
Adjusts the black level of the display
BRIGHTNESS
Adjusts the luminosity level of the display,
U - POSITION(HORIZONTAL POSITION) (D
act this control and then use the - and + buttons to center the image
horizontally on the screen.
H - SIZE(HORIZDNYAL SIZE) 5
Select this control and then use the - and + buttons to expand or
decrease the image width to horizontally fill the screen.
V-POSITIOMVERTICAL POSITION) 8
Select this control and then use the - and + buttons to center the image
vertically on the screen.
V-SIZEWERTICAL SIZE) ED
Select this control and then use the - and + buttons to adjust the image
height to vertically fill the screen
SIDE - PINlPINCUSHION) [m
Select this control, then use the - and + buttons to straighten the sides
of the image by pulling them in opposing directions.
PIN BALANCE
Select mis control. then use the - and + buttons to straighten the sides of the
image by pulling them in the corresponding direction.
CORNER PIN lfi
Select this control, then use the - and + buttons to straighten the top and
ENTER bottom comers of the image by pulling them in opposing directions.
TRAPEZOID .
Select this control, then use the - and + buttons to even the maths of the top
and bottom of the display (pulling the sides in opposite directions)
PARALLELOGRAM m
Select this control, then use the - and +buttons to center the top and bottom
of the display (pulling the sides in the corresponding direction).
meme @
Select this control, then press the + and - buttons to be disappeared the moire.
ROTATION
Use the - and 4» buttons to rotate the image until the sides of the image
are parallel to the edge of the bezel.
COLOR CONTROLHEMPERATURE) @
Select this control, then use the » and + buttons to scroll to the desired
color temperature. Use the ENTER button to select either the 9300K,
GSOOK or SSOOK or USER, for a custom setting
COLOR CONTROL
serum:
GAIN(RED) E]
ect “COLOR 4: USER" then use the ENTER button to scroll up and
m the RGB menu to R (Red). Use the 0 and + buttons to adjust the red
3! of the display
AIN(GREEN) [E]
ect ”COLOR 4: USER” then use the ENTER button to scroll up and
m the RGB menu to G (Green). Use the - and + buttons to adjust the
an level of the display,
AIN(BLUE)
act “color 4: USER” then use the ENTER button to scroll up and down
RGB menu to 5 (Blue). Use the - and + buttons to adjust the blue
H of the display.
IGUAGE 4)
act this control, then use the + and - buttons to choose from : English,
man(deutsch}, Spanish(espafiol), ltalian(italiano) or Frenchmancais)
~ lmsmow
; this control, then use the ENTER button to select in which
ction to move the OSD menu. Use the < and + buttons to move the
“I
7ALL E]
ets the display settings to the original factory reset values. Press and
l down the Enter button until the progress bar disappears
TIMING GU
IDE
The 15" color monitor is a multi-frequency monitor. It operates at
horizontal frequencies between 30 KHz and 70 KHz, vertical frequencies
between 50 Hz and 140 Hz. Because of its microprocessor-based
design, it offers auto-synchronization and autoasizmg capabilities.
This monitor offers 11 pare-programmed settings as listed in the table
below.
TABLE
Preset Resolution Frequency
Horizontal Vertical Horizontal Vertical
5 M1 720 400 3115 KHz l 70 Hz
JVGA M2 640 ‘ 430 L_31.5 KHz i so Hz
M3 540 480 37.5 KHz I 75 Hz
M47- 800 500 45.9 KHz l 75 Hz
[VESA M5 1024 768 60.0 KHz l 75 Hz
1 M6 1152 864 67.5 KHz I 75 Hz
1 M7 1280 1 1024 j 640 KHz I 60 Hz 1
MS ‘ 640 l 480 3 433 KHZ i 85 Hz
MS 800 i 500 l_ 537 KHz 5 as Hz
M10 1024 g 758 607 KHZ l 85 Hz
M11 __ 832 l 23 __ 49.7 KHz 1 75 Hz
. In addition to 1.1 factory modes, were are 5 additional use! modes.
If more than 7 modes are inputted, it Will be overrided m accomance With saving
order of additional modesi
. In case oiusing Macmtcsh, you must need Mac adapter.
10
SPECIFICATIONS
ls” 04.0" viewable) nonglare, antistatic,
dark Sony Trintron® tube with tinted aperture
grill and 90° deflection
Aperture Grille Pitch 0.25mm
Resolution 1ZEOIHIX102HV)
Non-interlaced (addressable)
Maximum Dot Clock 100MH2 at - 3 dB (nominal)
Video .nput Analog, positive going
signaIIOJV p—p)
Horizontal input TI'L, positive or negative
going pulset2.4~5V p—pl
Picture tube
Vertical Input TTL, positive or negative
going pulsei2.4~5V m3)
Scan frequency Horizontal: 30~70KHz
Vertical: 50~140Hz
I Standard display area 270mm(Hlx202mm(\/)l
IOYS‘IH) >< 7.9“(VI
Display color Unlimited
Power input too—zaov Ac, 50/60Hz
Fuse rating ' 250V, 3 3.0A(UL. CSA, TUV) or T 3,15Atfl'Jvl
On : Less than 90W
Stand by : Less than 15W
, Suspend : Less than 15W
I Off . Less than SW
Power consumption
Operating I 0 To 40 Degree C.
temperature
Dimensions 1 366mm(w) x 368mm(H) XAOme(D)
I 14.4'(W)Xi4.5'(H)><15-3'(D>
Weight MAKgInet) / 3 I .7Ibs
11
h" U'S USA
STANDARD NEW PRODUCT WARRANTY
Korea Data Systems. InctKDSlwarrants your new monitor product against defects in material
ano wofmanshlp lot a period of threelSl years item the date or the ong’nal purchase at the new
product, Thrs limited warranty covers the end-user for threelsl years on parts, M012) years on
the C37, and onelll year on labor i'cr new proouc: purchases only. Any product defecr not
originating from defects in materials or workmanship wrll not be considered covered under
warranty
ln the unlikely event that a component should fail during its mrecysar warranty period due to a
detect in memnals or workmanship. 1
Source Exif Data:
File Type : PDF
File Type Extension : pdf
MIME Type : application/pdf
PDF Version : 1.3
Linearized : Yes
Create Date : 2001:07:08 08:42:59
Producer : Acrobat Distiller 4.0 for Windows
Author : VicodinES /CB /TNN
Title : 19743.pdf
Modify Date : 2001:07:08 08:43:11-04:00
Page Count : 20
EXIF Metadata provided by EXIF.tools